The analysis and prediction of the quantity and composition of household refuse

This thesis describes the development of a simple and accurate method for estimating the quantity and composition of household waste arisings. The method is based on the fundamental tenet that waste arisings can be predicted from information on the demographic and socio-economic characteristics of households, thus reducing the need for the direct measurement of waste arisings to that necessary for the calibration of a prediction model. The aim of the research is twofold: firstly to investigate the generation of waste arisings at the household level, and secondly to devise a method for supplying information on waste arisings to meet the needs of waste collection and disposal authorities, policy makers at both national and European level and the manufacturers of plant and equipment for waste sorting and treatment. The research was carried out in three phases: theoretical, empirical and analytical. In the theoretical phase specific testable hypotheses were formulated concerning the process of waste generation at the household level. The empirical phase of the research involved an initial questionnaire survey of 1277 households to obtain data on their socio-economic characteristics, and the subsequent sorting of waste arisings from each of the households surveyed. The analytical phase was divided between (a) the testing of the research hypotheses by matching each household's waste against its demographic/socioeconomic characteristics (b) the development of statistical models capable of predicting the waste arisings from an individual household and (c) the development of a practical method for obtaining area-based estimates of waste arisings using readily available data from the national census. The latter method was found to represent a substantial improvement over conventional methods of waste estimation in terms of both accuracy and spatial flexibility. The research therefore represents a substantial contribution both to scientific knowledge of the process of household waste generation, and to the practical management of waste arisings.

The measurement and significance of ATP pools in activated sludge treating coke oven liquors

Coke oven liquor is a toxic wastewater produced in large quantities by the Iron and Steel, and Coking Industries, and gives rise to major effluent treatment problems in those industries. Conscious of the potentially serious environmental impact of the discharge of such wastes, pollution control agencies in many countries have made progressively more stringent quality requirements for the discharge of the treated waste. The most common means of treating the waste is the activated sludge process. Problems with achieving consistently satisfactory treatment by this process have been experienced in the past. The need to improve the quality of the discharge of the treated waste prompted attempts by TOMLINS to model the process using Adenosine Triphosophnte (ATP) as a measure of biomass, but these were unsuccessful. This thesis describes work that was carried out to determine the significance of ATP in the activated sludge treatment of the waste. The use of ATP measurements in wastewater treatment were reviewed. Investigations were conducted into the ATP behaviour of the batch activated sludge treatment of two major components of the waste, phenol, and thiocyanate, and the continuous activated sludge treatment of the liquor itself, using laboratory scale apparatus. On the basis of these results equations were formulated to describe the significance of ATP as a measured activity and biomass in the treatment system. These were used as the basis for proposals to use ATP as a control parameter in the activated sludge treatment of coke oven liquor, and wastewaters in general. These had relevance both to the treatment of the waste in the reactor and to the settlement of the sludge produced in the secondary settlement stage of the treatment process.

Waste to power

ABSTRACT: There has been a growing trend towards the use of biomass as a primary energy source, which now contributes over 54% of the European pulp and paper industry energy needs [1]. The remaining part comes from natural gas, which to a large extent serves as the major source of energy for numerous recovered fiber paper mills located in regions with limited available forest resources. The cost of producing electricity to drive paper machinery and generate heat for steam is increasing as world demand for fossil fuels increases. Additionally, recovered fiber paper mills are also significant producers of fibrous sludge and reject waste material that can contain high amounts of useful energy. Currently, a majority of these waste fractions is disposed of by landspreading, incineration, or landfill. Paper mills must also pay a gate fee to process their waste streams in this way and the result of this is a further increase in operating costs. This work has developed methods to utilize the waste fractions produced at recovered fiber paper mills for the onsite production of combined heat and power (CHP) using advanced thermal conversion methods (pyrolysis and gasification) that are well suited to relatively small scales of throughput. The electrical power created would either be used onsite to power the paper making process or alternatively exported to the national grid, and the surplus heat created could also be used onsite or exported to a local customer. The focus of this paper is to give a general overview of the project progress so far and will present the experimental results of the most successful thermal conversion trials carried out by this work to date. Application: The research provides both paper mills and energy providers with methodologies to condition their waste materials for conversion into useful energy. The research also opens up new markets for gasifier and pyrolysis equipment manufacturers and suppliers.

The intermediate pyrolysis of de-inking sludge to produce a sustainable liquid fuel

De-inking sludge is a waste product generated from secondary fibre paper mills who manufacture recycled paper into new paper sheets; it refers directly to the solid residues which evolve during the de-inking stage of the paper pulping process. The current practice for the disposal of this waste is either by land-spreading, land-filling or incineration which are unsustainable. This work has explored the intermediate pyrolysis of pre-conditioned de-inking sludge pellets in a recently patented 20 kg/h intermediate pyrolysis reactor (The Pyroformer). The reactor is essentially two co-axial screws which are configured in such a way as to circulate solids within the reactor and thus facilitate in the cracking of tars. The potential application of using the volatile organic vapours and permanent gases evolved would be to generate both combined heat and power (CHP) located at paper making sites. The results show that de-inking sludge could be successfully pyrolysed and the organic vapours produced were composed of a mixture of aromatic hydrocarbons, phenolic compounds and some fatty acid methyl esters as detected by liquid GC-MS. The calorific value of the oil after condensing was between 36 and 37 MJ/kg and the liquid fuel properties were also determined, permanent gases were detected by a GC-TCD and were composed of approximately 24% CO, 6% CH and 70% CO (v/v%). The solid residue from pyrolysis also contained a small residual calorific value, and was largely composed of mainly calcium based inert metal oxides. The application of applying intermediate pyrolysis to de-inking sludge for both CHP production and waste reduction is in principle a feasible technology which could be applied at secondary fibre paper mills. © 2013 Elsevier B.V. All rights reserved.

The intermediate pyrolysis of de-inking sludge to produce a sustainable liquid fuel

De-inking sludge is a waste product generated from secondary fibre paper mills who manufacture recycled paper into new paper sheets; it refers directly to the solid residues which evolve during the de-inking stage of the paper pulping process. The current practice for the disposal of this waste is either by land-spreading, land-filling or incineration which are unsustainable. This work has explored the intermediate pyrolysis of pre-conditioned de-inking sludge pellets in a recently patented 20 kg/h intermediate pyrolysis reactor (The Pyroformer). The reactor is essentially two co-axial screws which are configured in such a way as to circulate solids within the reactor and thus facilitate in the cracking of tars. The potential application of using the volatile organic vapours and permanent gases evolved would be to generate both combined heat and power (CHP) located at paper making sites. The results show that de-inking sludge could be successfully pyrolysed and the organic vapours produced were composed of a mixture of aromatic hydrocarbons, phenolic compounds and some fatty acid methyl esters as detected by liquid GC-MS. The calorific value of the oil after condensing was between 36 and 37 MJ/kg and the liquid fuel properties were also determined, permanent gases were detected by a GC-TCD and were composed of approximately 24% CO, 6% CH and 70% CO (v/v%). The solid residue from pyrolysis also contained a small residual calorific value, and was largely composed of mainly calcium based inert metal oxides. The application of applying intermediate pyrolysis to de-inking sludge for both CHP production and waste reduction is in principle a feasible technology which could be applied at secondary fibre paper mills. © 2013 Elsevier B.V. All rights reserved.

A decision support system for waste collection management and its potential improvement with Radio-Frequency Identification Technology (RFID)

Due to vigorous globalisation and product proliferation in recent years, more waste has been produced by the soaring manufacturing activities. This has contributed to the significant need for an efficient waste management system to ensure, with all efforts, the waste is properly treated for recycling or disposed. This paper presents a Decision Support System (DSS) framework, based on Constraint Logic Programming (CLP), for the collection management of industrial waste (of all kinds) and discusses the potential employment of Radio-Frequency Identification Technology (RFID) to improve several critical procedures involved in managing waste collection. This paper also demonstrates a widely distributed and semi-structured network of waste producing enterprises (e.g. manufacturers) and waste processing enterprises (i.e. waste recycling/treatment stations) improving their operations planning by means of using the proposed DSS. The potential RFID applications to update and validate information in a continuous manner to bring value-added benefits to the waste collection business are also presented. © 2012 Inderscience Enterprises Ltd.

Developing actions to minimise avoidable waste and its challenge to plant safety

Purpose: Considering the UK's limited capacity for waste disposal (particularly for hazardous/radiological waste) there is growing focus on waste avoidance and minimisation to lower the volumes of waste being sent to disposal. The hazardous nature of some waste can complicate its management and reduction. To address this problem there was a need for a decision making methodology to support managers in the nuclear industry as they identify ways to reduce the production of avoidable hazardous waste. The methodology we developed is called Waste And Sourcematter Analysis (WASAN). A methodology that begins the thought process at the pre-waste creation stage (i.e. Avoid). Design/methodology/ approach: The methodology analyses the source of waste, the production of waste inside the facility, the knock on effects from up/downstream facilities on waste production, and the down-selection of waste minimisation actions/options. WASAN has been applied to case studies with licencees and this paper reports on one such case study - the management of plastic bags in Enriched Uranium Residues Recovery Plant (EURRP) at Springfields (UK) where it was used to analyse the generation of radioactive plastic bag waste. Findings: Plastic bags are used in EURRP as a strategy to contain hazard. Double bagging of materials led to the proliferation of these bags as a waste. The paper reports on the philosophy behind WASAN, the application of the methodology to this problem, the results, and views from managers in EURRP. Originality/value: This paper presents WASAN as a novel methodology for analyzing the minimization of avoidable hazardous waste. This addresses an issue that is important to many industries e.g. where legislation enforces waste minimization, where waste disposal costs encourage waste avoidance, or where plant design can reduce waste. The paper forms part of the HSE Nuclear Installations Inspectorate's desire to work towards greater openness and transparency in its work and the development in its thinking.© Crown Copyright 2011.

Experimental investigation of the fuel properties of glidfuel, palm oil mill effluent biodiesel and blends

Biofuels derived from industry waste have potential to substitute fossil fuels (Diesel and Gasoline) in internal combustion (IC) engines. Use of waste streams as fuels would help to reduce considerably life-cycle greenhouse gas emissions and minimise waste processing costs. In this study an investigation into the fuel properties of two waste derived biofuels were carried out, they are: (i) Glidfuel (GF) biofuel - a waste stream from paper industry, and (ii) Palm Oil Mill Effluent (POME) biodiesel - biodiesel produced from palm oil industry effluent through various treatment and transesterification process. GF and POME was mixed together at various proportions and separately with fossil diesel (FD) to assess the miscibility and various physical and chemical properties of the blends. Fuel properties such as kinematic viscosity, higher heating value, water content, acid number, density, flash point temperature, CHNO content, sulphur content, ash content, oxidation stability, cetane number and copper corrosion ratings of all the fuels were measured. The properties of GF, POME and various blends were compared with the corresponding properties of the standard FD. Significance of the fuel properties and their expected effects on combustion and exhaust emission characteristics of the IC engine were discussed. Results showed that most properties of both GF and POME biodiesel were comparable to FD. Both GF and POME were miscible with each other, and also separately with the FD. Flash point temperatures of GF and POME biodiesel were 40.7°C and 158.7°C respectively. The flash point temperature of GF was about 36% lower than corresponding FD. The water content in GF and FD were 0.74 (% wt) and 0.01 (% wt) respectively. Acidity values and corrosion ratings of both GF and POME biodiesel were low compared to corresponding value for FD. The study concluded that optimum GF-POME biofuel blends can substitute fossil diesel use in IC engines.

A globálisan növekvő hulladékmennyiség és a kezelésére irányuló nemzetközi törekvések (International efforts to cope with globally increasing waste amounts)

Sokoldalú nemzetközi megállapodások és programok foglalkoznak a hulladékok keletkezésének és az országhatárokon átterjedő hatásainak problémájával, a nemzetközi együttműködést szükségessé tevő megoldásokkal. A leginkább átfogó megközelítést a probléma hajtóerőinek szentelt globális programok tartalmazzák, de a fenntarthatóság alapelveire támaszkodó termelési eljárásokra és fogyasztási szokásokra, a zöld gazdaságra való áttérést szorgalmazó dokumentumok nem tartalmaznak számon kérhető kötelezettségeket. A konkrétabb hulladékkeletkezési és hatásterjedési ügyekben – mindenekelőtt a veszélyes hulladékok és a nemzeti fennhatóság alá nem tartozó területekre eljutó vagy ott keletkező hulladékok esetében – jóval konkrétabb nemzetközi megállapodások és programok léteznek. Ezek szabályozási, szakpolitikai, technológiai célokat, feladatokat határoznak meg az országok és az érintett ágazati szereplők szintjén is. Egyes problémák kapcsán és egyes térségekben a hulladékgazdálkodás jelentős eredményeket tud felmutatni, de általában véve a nemzetközi megállapodások hatékony végrehajtásával komoly gondok vannak. Továbbá a meglévő nemzetközi eszközök összességükben még teljes körű végrehajtásuk esetén sem lennének képesek ellensúlyozni a hulladékprobléma globális szintű növekedését. Következésképpen további erőfeszítésekre van szükség – minden kormány, érintett nem-kormányzati szervezet és az ágazatok részéről – különösen a megelőzés vonatkozásában. ____ Various multilateral agreements and programmes deal with the problems of waste generation and its transboundary impacts, and those solutions, which necessitate international co-operation. Those global programmes include the most comprehensive approach, which are dedicated to the drivers of these problems, however, these documents promoting the transition to sustainable production and consumption, or to the green economy do not consist of binding commitments. In case of more concrete issues of waste generation and transboundary impacts there are much more concrete international agreements and programmes, especially, for the hazardous waste streams and the waste transmitted to and/or generated in areas outside national jurisdiction. These determine regulatory, policy, technological goals and tasks for the participating countries and the relevant sectors. Significant progress is demonstrated for some specific problems and in certain regions, but in general, there are serious concerns about the efficient implementation of the international agreements in their entirety. Moreover, even if those were fully accomplished, the existing set of the international instruments would be unable to counterweigh the global increase of the waste problem. Consequently, further efforts are needed by all countries, the relevant non-governmental organisations and sectors, primarily in order to prevent the further global escalation of the problem.

The Study of Sonar for Imaging of the Solid-Liquid Interface Inside Large Tanks

Retrieval, treatment, and disposal of high-level radioactive waste (HLW) is expected to cost between 100 and 300 billion dollars. The risk to workers, public health, and the environment are also a major area of concern for HLW. Visualization of the interface between settled solids and the optically opaque liquid is needed for retrieval of the waste from underground storage tanks. A Profiling sonar selected for this research generates 2-D image of the interface. Multiple experiments were performed to demonstrate the effectiveness of sonar in real-time monitoring the interface inside HLW tanks. First set of experiments demonstrated that objects shapes could be identified even when 30% of solids entrained in liquid, thereby mapping the interface. Simulation of sonar system validated these results. Second set of experiments confirmed the sonar’s ability in detecting the solids with density similar to the immersed liquid. Third set of experiments determined the affects of near by objects on image resolution. Final set of experiments proved the functional and chemical capabilities of sonar in caustic solution.

Waste Not, Want Not: Managing Perishables in Small and Medium Retail Enterprises

Purpose of this paper:
Recent literature indicates that around one third of perishable products finish as waste (Mena et al., 2014): 60% of this waste can be classified as avoidable (EC, 2010) suggesting logistics and operational inefficiencies along the supply chain. In developed countries perishable products are predominantly wasted in wholesale and retail (Gustavsson et al., 2011) due to customer demand uncertainty the errors and delays in the supply chain (Fernie and Sparks, 2014). While research on logistics of large retail supply chains is well documented, research on retail small and medium enterprises’ (SMEs) capabilities to prevent and manage waste of perishable products is in its infancy (c.f. Ellegaard, 2008) and needs further exploration. In our study, we investigate the retail logistics practice of small food retailers, the factors that contribute to perishable products waste and the barriers and opportunities of SMEs in retail logistics to preserve product quality and participate in reverse logistics flows.

Design/methodology/approach:
As research on waste of perishable products for SMEs is scattered, we focus on identifying key variables that contribute to the creation of avoidable waste. Secondly we identify patterns of waste creation at the retail level and its possibilities for value added recovery. We use explorative case studies (Eisenhardt, 1989) and compare four SMEs and one large retailer that operate in a developed market. To get insights into specificities of SMEs that affect retail logistics practice, we select two types of food retailers: specialised (e.g. greengrocers and bakers) and general (e.g. convenience store that sells perishable products as a part of the assortment)

Findings:
Our preliminary findings indicate that there is a difference between large retailers and SME retailers in factors that contribute to the waste creation, as well as opportunities for value added recovery of products. While more factors appear to affect waste creation and management at large retailers, a small number of specific factors appears to affect SMEs. Similarly, large retailers utilise a range of practices to reduce risks of product perishability and short shelf life, manage demand, and manage reverse logistics practices. Retail SMEs on the other hand have limited options to address waste creation and value added recovery. However, our findings show that specialist SMEs could successfully minimize waste and even create possibilities for value added recovery of perishable products. Data indicates that business orientation of the SME, the buyersupplier relationship, and an extent of adoption of lean principles in retail coupled with SME resources, product specific regulations and support from local authorities for waste management or partnerships with other organizations determine extent of successful preservation of a product quality and value added recovery.

Value:
Our contribution to the SCM academic literature is threefold: first, we identify major factors that contribute to the generation waste of perishable products in retail environment; second, we identify possibilities for value added recovery for perishable products and third, we present opportunities and challenges for SME retailers to manage or participate in activities of value added recovery. Our findings contribute to theory by filling a gap in the literature that considers product quality preservation and value added recovery in the context of retail logistics and SMEs.

Research limitations/implications:
Our findings are limited to insights from five case studies of retail companies that operate within a developed market. To improve on generalisability, we intend to increase the number of cases and include data obtained from the suppliers and organizations involved in reverse logistics flows (e.g. local authorities, charities, etc.).

Practical implications:
With this paper, we contribute to the improvement of retail logistics and operations in SMEs which constitute over 99% of business activities in UK (Rhodes, 2015). Our findings will help retail managers and owners to better understand the possibilities for value added recovery, investigate a range of logistics and retail strategies suitable for the specificities of SME environment and, ultimately, improve their profitability and sustainability.

Sustainable solutions for the construction sector: integration of secondary raw materials in the production cycle of concrete

The construction industry is one of the largest consumers of raw materials and energy and one of the highest contributor to green-houses gases emissions. In order to become more sustainable it needs to reduce the use of both raw materials and energy, thus lim-iting its environmental impact. Developing novel technologies to integrate secondary raw materials (i.e. lightweight recycled aggre-gates and alkali activated “cementless” binders - geopolymers) in the production cycle of concrete is an all-inclusive solution to im-prove both sustainability and cost-efficiency of construction industry. SUS-CON “SUStainable, Innovative and Energy-Efficiency CONcrete, based on the integration of all-waste materials” is an European project (duration 2012-2015), which aim was the inte-gration of secondary raw materials in the production cycle of concrete, thus resulting in innovative, sustainable and cost-effective building solutions. This paper presents the main outcomes related to the successful scaling-up of SUS-CON concrete solutions in traditional production plants. Two European industrial concrete producers have been involved, to design and produce both pre-cast components (blocks and panels) and ready-mixed concrete. Recycled polyurethane foams and mixed plastics were used as aggre-gates, PFA (Pulverized Fuel Ash, a by-product of coal fuelled power plants) and GGBS (Ground Granulated Blast furnace Slag, a by-product of iron and steel industries) as binders. Eventually, the installation of SUS-CON concrete solutions on real buildings has been demonstrated, with the construction of three mock-ups located in Europe (Spain, Turkey and Romania)

STARD 2015: an updated list of essential items for reporting diagnostic accuracy studies

Incomplete reporting has been identified as a major source of avoidable waste in biomedical research.
Essential information is often not provided in study reports, impeding the identification, critical
appraisal, and replication of studies. To improve the quality of reporting of diagnostic accuracy
studies, the Standards for Reporting Diagnostic Accuracy (STARD) statement was developed. Here
we present STARD 2015, an updated list of 30 essential items that should be included in every
report of a diagnostic accuracy study. This update incorporates recent evidence about sources of
bias and variability in diagnostic accuracy and is intended to facilitate the use of STARD. As such,
STARD 2015 may help to improve completeness and transparency in reporting of diagnostic accuracy
studies.

Tailoring Magnetic, Mechanical and Dielectric Properties of Magnetorheological Elastomers based on Natural Rubber and Iron by Magnetic Field Assisted Curing for Possible Applications

If magnetism is universal in nature, magnetic materials are ubiquitous. A life without magnetism is unthinkable and a day without the influence of a magnetic material is unimaginable. They find innumerable applications in the form of many passive and active devices namely, compass, electric motor, generator, microphone, loud speaker, maglev train, magnetic resonance imaging, data recording and reading, hadron collider etc. The list is endless. Such is the influence of magnetism and magnetic materials in ones day to day life. With the advent of nanoscience and nanotechnology, along with the emergence of new areas/fields such as spintronics, multiferroics and magnetic refrigeration, the importance of magnetism is ever increasing and attracting the attention of researchers worldwide. The search for a fluid which exhibits magnetism has been on for quite some time. However nature has not bestowed us with a magnetic fluid and hence it has been the dream of many researchers to synthesize a magnetic fluid which is thought to revolutionize many applications based on magnetism. The discovery of a magnetic fluid by Jacob Rabinow in the year 1952 paved the way for a new branch of Physics/Engineering which later became magnetic fluids. This gave birth to a new class of material called magnetorheological materials. Magnetorheological materials are considered superior to electrorheological materials in that magnetorheology is a contactless operation and often inexpensive.Most of the studies in the past on magnetorheological materials were based on magnetic fluids. Recently the focus has been on the solid state analogue of magnetic fluids which are called Magnetorheological Elastomers (MREs). The very word magnetorheological elastomer implies that the rheological properties of these materials can be altered by the influence of an external applied magnetic field and this process is reversible. If the application of an external magnetic field modifies the viscosity of a magnetic fluid, the effect of external magnetic stimuli on a magnetorheological elastomer is in the modification of its stiffness. They are reversible too. Magnetorheological materials exhibit variable stiffness and find applications in adaptive structures of aerospace, automotive civil and electrical engineering applications. The major advantage of MRE is that the particles are not able to settle with time and hence there is no need of a vessel to hold it. The possibility of hazardous waste leakage is no more with a solid MRE. Moreover, the particles in a solid MRE will not affect the performance and durability of the equipment. Usually MR solids work only in the pre yield region while MR fluids, typically work in the post yield state. The application of an external magnetic field modifies the stiffness constant, shear modulus and loss modulus which are complex quantities. In viscoelastic materials a part of the input energy is stored and released during each cycle and a part is dissipated as heat. The storage modulus G′ represents the capacity of the material to store energy of deformation, which contribute to material stiffness. The loss modulusG′′ represents the ability of the material to dissipate the energy of deformation. Such materials can find applications in the form of adaptive vibration absorbers (ATVAs), stiffness tunable mounts and variable impedance surfaces. MREs are an important material for automobile giants and became the focus of this research for eventual automatic vibration control, sound isolation, brakes, clutches and suspension systems

Model based integration of management systems (MSs) – case study

Abstract Purpose – The purpose of this paper is to present a case study regarding the deployment of a previously developed model for the integration of management systems (MSs). The case study is developed at a manufacturing site of an international enterprise. The implementation of this model in a real business environment is aimed at assessing its feasibility. Design/methodology/approach – The presented case study takes into account different management systems standards (MSSs) progressively implemented, along the years, independently. The implementation of the model was supported by the results obtained from an investigation performed according to a structured diagnosis that was conducted to collect information related to the organizational situation of the enterprise. Findings – The main findings are as follows: a robust integrated management system (IMS), objectively more lean, structured and manageable was found to be feasible; this study provided an holistic view of the enterprise’s global management; clarifications of job descriptions and boundaries of action and responsibilities were achieved; greater efficiency in the use of resources was attained; more coordinated management of the three pillars of sustainability – environmental, economic and social, as well as risks, providing confidence and added value to the company and interested parties was achieved. Originality/value – This case study is pioneering in Portugal in respect to the implementation, at the level of an industrial organization, of the model previously developed for the integration of individualized MSs. The case study provides new insights regarding the implementation of IMSs including the rationalization of several resources and elimination of several types of organizational waste leveraging gains of efficiency. Due to its intrinsic characteristics, the model is able to support, progressively, new or revised MSSs according to the principles of annex SL (normative) – proposals for MSSs – of the International Organization for Standardization and the International Electrotechnical Commission, that the industrial organization can adopt beyond the current ones.