Trimethoprim-selective electrodes with molecularly imprinted polymers acting as ionophores and potentiometric transduction on graphite solid-contact

This work proposes a new biomimetic sensor material for trimethoprim. It is prepared by means of radical polymerization, having trimethylolpropane trimethacrylate as cross-linker, benzoyl peroxide as radicalar iniciator, chloroform as porogenic solvent, and methacrylic acid and 2-vinyl pyridine as monomers. Different percentages of sensor in a range between 1 and 6% were studied. Their behavior was compared to that obtained with ion-exchanger quaternary ammonium salt (additive tetrakis(p-chlorophenyl)borate or tetraphenylborate). The effect of an anionic additive in the sensing membrane was also tested. Trimethoprim sensors with 1% of imprinted particles from methacrylic acid monomers showed the best response in terms of slope (59.7 mV/decade) and detection limit (4.01 × 10− 7 mol/L). These electrodes displayed also a good selectivity towards nickel, manganese aluminium, ammonium, lead, potassium, sodium, iron, chromium, sulfadiazine, alanine, cysteine, tryptophan, valine and glycine. The sensors were not affected by pH changes from 2 to 6. They were successfully applied to the analysis of water from aquaculture.

Trace Elements in Ambient Air at Porto Metropolitan Area—Checking for Compliance with New European Union (Eu) Air Quality Standards

Because of the scientific evidence showing that arsenic (As), cadmium (Cd), and nickel (Ni) are human genotoxic carcinogens, the European Union (EU) recently set target values for metal concentration in ambient air (As: 6 ng/m3, Cd: 5 ng/m3, Ni: 20 ng/m3). The aim of our study was to determine the concentration levels of these trace elements in Porto Metropolitan Area (PMA) in order to assess whether compliance was occurring with these new EU air quality standards. Fine (PM2.5) and inhalable (PM10) air particles were collected from October 2011 to July 2012 at two different (urban and suburban) locations in PMA. Samples were analyzed for trace elements content by inductively coupled plasma–mass spectrometry (ICP-MS). The study focused on determination of differences in trace elements concentration between the two sites, and between PM2.5 and PM10, in order to gather information regarding emission sources. Except for chromium (Cr), the concentration of all trace elements was higher at the urban site. However, results for As, Cd, Ni, and lead (Pb) were well below the EU limit/target values (As: 1.49 ± 0.71 ng/m3; Cd: 1.67 ± 0.92 ng/m3; Ni: 3.43 ± 3.23 ng/m3; Pb: 17.1 ± 10.1 ng/m3) in the worst-case scenario. Arsenic, Cd, Ni, Pb, antimony (Sb), selenium (Se), vanadium (V), and zinc (Zn) were predominantly associated to PM2.5, indicating that anthropogenic sources such as industry and road traffic are the main source of these elements. High enrichment factors (EF > 100) were obtained for As, Cd, Pb, Sb, Se, and Zn, further confirming their anthropogenic origin.

Study and characterization of the ZnPc:C60/MoOx interface in organic solar cells by means of photoelectron spectroscopy

Dissertation to obtain the academic degree of Master in materials engineering submitted to the Faculty of science and engineering of Universidade Nova de Lisboa

Expressão e purificação da proteína E3 do vírus chikungunya (CHIKV)

RESUMO: O vírus chikungunya (CHIKV) é um vírus de RNA, com invólucro, da família Togaviridae, transmitido por mosquitos Aedes spp. Distribuído por largas regiões de África e Ásia, causa grandes epidemias de artrite grave. A semelhança de sintomas com outras doenças como a dengue e a malária e a persistência de IgM específicas, dificultam o diagnóstico da infeção por CHIKV. A deteção no sangue de E3, uma glicoproteína viral secretada, a incluir num ensaio imunoenzimático poderá melhorar o diagnóstico nos países onde as técnicas de biologia molecular são de difícil acesso. Para testar a utilidade de E3 num ensaio de diagnóstico, esta deverá ser expressa em quantidade, purificada e usada para produção de anticorpos específicos. Para expressar E3 numa forma solúvel, suscetível de ser purificada num único passo cromatográfico sem proteases, recorreu-se à estratégia da fusão com o domínio de ligação à quitina (CBD)-inteína (IMPACT™ System, NEB). A sequência codificadora de E3 foi amplificada a partir de RNA viral, clonada em pTYB21 e expressa em E. coli como uma proteína de fusão insolúvel de 64 kDa. A expressão a 12ºC induzida por IPTG 0,1 mM aumentou a solubilidade de CBD-inteína-E3. A aplicação de lisados celulares em colunas de quitina originou a retenção de CBD-inteína-E3 na matriz. Porém, a autoclivagem da inteína na coluna, induzida com reagentes tiol, foi pouco eficiente e mesmo a proteína E3 separada não eluiu da coluna. E3 foi ainda expressa em E. coli com uma cauda de seis histidinas (E3[His]6) por clonagem no vetor pET28b(+). Lisados celulares aplicados em colunas de níquel permitiram a eluição de uma proteína de 9 kDa, compatível com a massa molecular estimada para E3[His]6, ainda que com outros contaminantes proteicos. A identidade da proteína de 9 kDa será confirmada pela indução de anticorpos com esta preparação e reatividade daqueles com células infetadas com CHIKV.----------------ABSTRACT: Chikungunya virus (CHIKV) is an enveloped, positive strand RNA virus belonging to the family Togaviridae. Transmitted by Aedes spp mosquitoes, CHIKV causes large epidemics of severe arthritogenic disease in Africa and Asia and represents a serious threat in countries where vectors are present. Symptoms similarity with other diseases, e.g. dengue and malaria, along with CHIKV IgM persistence turns accurate CHIKV diagnosis a difficult task in low-income countries. Detection of E3, a small secreted viral glycoprotein, to be included in an immunoenzymatic test was envisaged as a possible improvement in CHIKV diagnosis. To test the diagnostic value of E3, recombinant E3 should be expressed and purified to generate antibodies. In order to express CHIKV E3 in a soluble form amenable to purification by a single step affinity chromatography, the chitin binding domain (CBD)-intein fusion strategy without proteases (IMPACT™ System, NEB) was employed. The E3 coding sequence was amplified from viral RNA, cloned in pTYB21 and expressed in E. coli ER2566 as an insoluble 64 kDa CBD-intein-E3 fusion protein. Solubility was partially achieved by lowering the expression temperature to 12ºC and the inducer (IPTG) concentration to 0.1 mM. Clarified cell lysate loaded onto a chitin column allowed ligation of the fusion protein but the intein-mediated cleavage efficiency was low and E3 failed to elute from the column as demonstrated by SDS-PAGE. E3 was further expressed with a six histidine tag, E3[His]6, employing the pET System (Novagen). E3[His]6 was expressed in E. coli Rosetta (30ºC, 0.4 mM IPTG) as a 9 kDa protein. Soluble cell extracts in 20-40 mM imidazole, applied onto a nickel column and eluted with 500 mM imidazole yielded a protein preparation enriched in the 9kDa protein. The 9 kDa will be used as antigen to generate antibodies that upon reaction with CHIKV infected cells will confirm its identity.

Towards printed carbon nanotube transistors on paper substrates

This thesis reports the work performed in the optimization of deposition parameters of Multi – Walled Carbon Nanotubes (MWCNT) targeting the development of a Field Effect Transistors (FET) on paper substrates. The CNTs were dispersed in a water solution with sodium dodecyl sulphate (SDS) through ultrasonication, ultrasonic bath and a centrifugation to remove the supernatant and have a homogeneous solution. Several deposition tests were performed using different types of CNTs, dis-persants, papers substrates and deposition techniques, such as spray coating and inkjet printing. The characterization of CNTs was made by Scanning Electron Microscopy (SEM) and Hall Effect. The most suitable CNT coatings able to be used as semiconductor in FETs were deposited by spray coat-ing on a paper substrate with hydrophilic nanoporous surface (FS2) at 100 ºC, 4 bar, 10 cm height, 5 second of deposition time and 90 seconds of drying between steps (4 layers of CNTs were deposited). Planar electrolyte gated FETs were produced with these layers using gold-nickel gate, source and drain electrodes. Despite the small current modulation (Ion/Ioff ratio of 1.8) one of these devices have p-type conduction with a field effect mobility of 1.07 cm2/V.s.

Mechanical, fatigue and wear properties of sintered Carbon Nanotube-based functionally graded materials

Tese de Doutoramento Engenharia Mecânica

Processamento e caracterização mecânica e metalográfica de compósitos adiamantados à base de cobre-níquel obtidos por hot pressing

Dissertação de mestrado em Engenharia de Materiais

Clivagem e caracterização de frutalina recombinante produzida em Escherichia coli

Dissertação de mestrado integrado em Engenharia Biomédica (área de especialização em Engenharia Clínica)

Expressão e caracterização de uma lectina recombinante de interesse biomédico

Dissertação de mestrado integrado em Engenharia Biomédica (área de especialização em Engenharia Clínica)

Synthesis of five-membered heterocycles by indirect electrochemical approach in "Green" media

Radical cyclization continues to be a central methodology for the preparation of natural products containing heterocyclic rings. Hence, some electrochemical results obtained by cyclic voltammetry and controlled-potential electrolysis in the study of electroreductive intramolecular cyclization of ethyl (2S, 3R)-2-bromo-3-propargyloxy-3-(2’,3’,4’,6’-tetra-O-acetyl-beta-D-glucopyranosyloxy) propanoate (1a), 2-bromo-3-allyloxy-3-(2’,3’,4’,6’-tetra-O-acetyl-beta-D-glucopyranosyloxy)propanoate (1b), 2-bromo-[1-(prop-2-yn-1-yloxy)propyl]benzene (1c) and [1-bromo-2-methoxy-2-(prop-2’-yn-1-yloxy)ethyl]benzene (1d) promoted by (1,4,8,11-tetramethyl-1,4,8,11-tetraazacyclotetradecane)nickel(I), [Ni(tmc)]+, electrogenerated at glassy carbon cathodes in ethanol and ethanol:water mixtures containing tetraalkylammonium salts, are presented. During controlled-potential electrolyses of solutions containing [Ni(tmc)]2+ and bromoalkoxylated compounds (1) catalytic reduction of the latter proceeds via one-electron cleavage of the carbon–bromine bond to form a radical intermediate that undergoes cyclization to afford the substituted tetrahydrofurans.

Electrosynthesis of heterocyclic compounds by radical cyclization in environmentally friendly media

We investigated the reductive intramolecular cyclization of bromopropargyl ethers derivatives, catalyzed by electrogenerated (1,4,8,11-tetramethyl-1,4,8,11-tetraaza-cyclotetradecane)nickel(I), [Ni(tmc)]+ as the catalysts in N,N,N-trimethyl-N-(2- hydroxyethyl)ammonium bis(trifluoromethylsulfonyl)imide,[N1 1 1 2(OH)][NTf2] and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C2mim][NTf2] by cyclic voltammetry and controlled-potential electrolysis. The results show that the reaction leads to the formation of the expected cyclic compounds, which are important intermediates in the synthesis of natural products with possible biological activities.

Reflow soldering in an oxidant atmosphere

Dissertação de mestrado integrado em Materials Engineering

Virulence markers and antimicrobial susceptibility of bacteria of the Bacteroides fragilis group isolated from stool of children with diarrhea in São Paulo, Brazil

Bacteroides fragilis has been isolated from several human and non-human monomicrobial and mixed infections. In this study, some virulence markers and the antimicrobial susceptibility of bacteria of the B. fragilis group isolated from children's stools were evaluated. All the 64 isolates showed the following characteristics: capsulated, beta-hemolytic, hydrophilic, and serum-resistant. Only, 24 (37.5%) strains were resistant at 60ºC, for 30 min, and among them, 12 (18.75%) were resistant at 60ºC, for 60 min. Also, none strain was resistant at 100ºC. Four strains were able to hemagglutinate erythrocytes and D-mannose, D-galactose, D-arabinose, and D-xylose inhibited hemagglutination in 2 B. fragilis strains (p76a, p76b). The hemagglutination in the strain B. uniformis p3-2 was inhibited by D-xylose and D-galactose. The bft gene detection and the enterotoxin production were observed only in 13 EF-enterotoxigenic species. Fragilysin activity was confirmed on HT-29 cells. The antimicrobial determination confirmed that both imipenem and metronidazole were efficient against B. fragilis species; all the strains were resistant to lead and nickel. Plasmids of 2.9, 4.4, 4.8, and 8.9 kb were observed in 6 tested strains. These results show the values of the species identification from clinical infections, as well as of the periodic evaluation of the resistance patterns of the B. fragilis group at Brazilian medical institutions.

Survey of antimicrobial susceptibility patterns of the bacteria of the Bacteroides fragilis group isolated from the intestinal tract of children

The bacteria of the Bacteroides fragilis group are considered important clinical pathogens and they are the most common anaerobes isolated from human endogenous infections. In this study, the susceptibility patterns to antibiotics and metals of 114 species of the B. fragilis group isolated from children with and without diarrhea were determined. Susceptibility was assayed by using an agar dilution method with Wilkins-Chalgren agar. All B. fragilis strains were resistant to lead and nickel, but susceptible to metronidazole and imipenem. beta-lactamase production was detected by using biological and nitrocefin methods, respectively, in 50% and 90.6% of the isolates of children with diarrhea and in 60% and 90% of the isolates of children without diarrhea. Our results show an increase of antibiotics and metals resistance in this microbial group, and a periodic evaluation of the antimicrobial susceptibility is needed. In Brazil, the contamination for antibiotics or metal ions is often observed, and it is suggested an increase the antimicrobial resistance surveillance of this microbial group, mainly those isolated from children's diarrhea.

Ab initio absorption spectrum of NiO combining molecular dynamics with the embedded cluster approach in a discrete reaction field

We developed a procedure that combines three complementary computational methodologies to improve the theoretical description of the electronic structure of nickel oxide. The starting point is a Car-Parrinello molecular dynamics simulation to incorporate vibrorotational degrees of freedom into the material model. By means ofcomplete active space self-consistent field second-order perturbation theory (CASPT2) calculations on embedded clusters extracted from the resulting trajectory, we describe localized spectroscopic phenomena on NiO with an efficient treatment of electron correlation. The inclusion of thermal motion into the theoretical description allowsus to study electronic transitions that, otherwise, would be dipole forbidden in the ideal structure and results in a natural reproduction of the band broadening. Moreover, we improved the embedded cluster model by incorporating self-consistently at the complete active space self-consistent field (CASSCF) level a discrete (or direct) reaction field (DRF) in the cluster surroundings. The DRF approach offers an efficient treatment ofelectric response effects of the crystalline embedding to the electronic transitions localized in the cluster. We offer accurate theoretical estimates of the absorption spectrum and the density of states around the Fermi level of NiO, and a comprehensive explanation of the source of the broadening and the relaxation of the charge transferstates due to the adaptation of the environment