Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid

Obtenção de uma porcelana dielétrica a partir de matérias-primas do Rio Grande do Norte

The dielectric porcelain is usually obtained by mixing various raw materials proportions and is used in the production of electronic equipment for various applications, from capacitors of high and low Power to insulators for low, medium, high and extra high voltage, which are used in distribution lines and transmission of electricity.This work was directed to the s tudy of technological properties of technic porcelain, made from raw materials extracted from pegmatites found in the regions of Seridó and the Alto Oeste of Rio Grande do Norte, which are made of kaolin, quartz and feldspar, abundant and high quality in these regions. The technic ceramics were obtained by mixing in appropriate levels, kaolin, feldspar, quartz and clay, the last item from a pottery in the city of Sao Gonçalo do Amarante, Rio Grande do Norte. During the development the following characterizations correlated to raw materials were made: laser particle sizing, x-ray diffraction, DTA and TG. The compositions studied were formed by uniaxial pressing at a pressure of 50 MPa and sintered at temperatures ranging from 1150 to 1350ºC and levels (times) of sintering between 30, 60, 90 and 120 minutes. The characterization of the samples were taken from the analysis of weight loss, linear shrinkage, porosity, stoneware curve, bulk density, flexural strength of three points, SEM and X-ray diffraction, TMA, Dielectric and cross Resistivity. The studied materials can be employed in producing the objects used in electrical engineering such as: insulators for low, medium and high-voltage electrical systems, command devices, bushing insulation for transformers, power capacitors, spark plugs, receptacles for fluorescent and incandescent light bulbs and others

Estudos comparativos do ciclo de regeneração de diferentes tipos de silicoaluminofosfatos

Different types of heterogeneous catalysts of the silicoaluminophosphate type, (SAPO-5, SAPO-11, SAPO-31, SAPO-34 and SAPO-41), molecular sieves with a: AFI, AEL, ATO, CHA and AFO structure, respectively, were synthesized through the hydrothermal method. Using sources such as hydrated alumina (pseudobohemita), phosphoric acid, silica gel, water, as well as, different types of organic structural templates, such as: cetyltrimethylammonium bromide (CTMABr), di-isopropylamine (DIPA), di-n- propylamine (DNPA) and tetraethylammonium hydroxide (TEOS), for the respective samples. During the preparation of the silicoaluminophosphates, the crystallization process of the samples occurred at a temperature of approximately 200 ° C, ranging through periods of 18-72 h, when it was possible to obtain pure phases for the SAPOs. The materials were furthermore washed with deionized water, dried and calcined to remove the molecules of the templates. Subsequently the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), absorption spectroscopy in the infrared region (FT-IR), specific surface area and thermal analysis via TG/DTG. The acidic properties were determined using adsorption of n-butylamine followed by programmed termodessorption. These methods revealed that the SAPO samples showed a typically weak to moderate acidity. However, a small amount of strong acid sites was also detected. The deactivation of the catalysts was conducted by artificially coking the samples, followed by n-hexane cracking reactions in a fixed bed with a continuous flow micro-reactor coupled on line to a gas chromatograph. The main products obtained were: ethane, propane, isobutene, n-butane, n-pentane and isopentane. The Vyazovkin (model-free) kinetics method was used to determine the catalysts regeneration and removal of the coke

Síntese hidrotérmica assistida por micro-ondas de tiO2, e aplicação em nanocompósito

In recent decades have seen a sharp growth in the study area of nanoscience and nanotechnology and is included in this area, the study of nanocomposites with self-cleaning properties. Since titanium dioxide (TiO2) has high photocatalytic activity and also antimicrobial, self-cleaning surfaces in your application has been explored. In this study a comparison was made between two synthesis routes to obtain TiO2 nanoparticles by hydrothermal method assisted by microwave. And after analysis of XRD and SEM was considered the best material for use in nanocomposites. It was deposited nanocomposite film of poly (dimethyl siloxane) (PDMS) with 0.5, 1, 1.5 and 2% by weight of nanoparticles of titanium dioxide (TiO2) by the spraying method. The nanocomposite was diluted with hexane and the suspension was deposited onto glass substrate, followed by curing in an oven with forced air circulation. The photocatalytic activity of the nanocomposite impregnated with methylene blue was evaluated by UV- vis spectroscopy from the intensity variation of absorption main peak at 660nm with time of exposure to the UV chamber. Changes in the contact angle and microhardness were analyzed before and after UV aging test. The effect of ultraviolet radiation on the chemical structure of the PDMS matrix was evaluated by spectrophotometry Fourier transform infrared (FTIR).The results indicated that the addition of TiO2 nanoparticles in the coating PDMS gave high photocatalytic activity in the decomposition of methylene blue, an important characteristic for the development of self-cleaning coatings

Preparação e caracterização de catalisadores à base de titânio suportado em MCM-41 para produção de compostos oxigenados através da pirólise catalítica do capim elefante

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Avaliação da correlação entre os parâmetros, carbono orgânico total e elementos tóxicos, em solo de um posto de serviço e revenda de combustíveis

Today a major responsibility for the contamination of soil and groundwater and surface water are establishments known as gas stations of fuel which has attracted increasing attention from both the general population as the state agencies of environmental control due to leaks in storage tanks and mainly to disruption of pipe corrosion of tanks and pumping. Other services, like oil changes and car wash are also causes for concern in this type of establishment. These leaks can cause or waste produced, and the contamination of aquifers, serious health problems and public safety, since most of these stations located in urban areas. Based on this, the work was to evaluate soil contamination of a particular service station and fuel sales in the city of Natal, through the quantification of heavy metals like Cd, Cu, Cr, Ni, Pb, Zn of total organic carbon (TOC) and organic matter using different techniques such as optical emission spectrometry with inductively coupled plasma source (ICP OES), Total Organic Carbon analyzer and gravimetric analysis respectively. And also to characterize the soil through particle size analysis. Samples were taken in 21 georeferenced points and collected in the same period. The soils sampled in sampling stations P3, P5, P6, P10, P11, P12, P13, P14, P15, P17, P18 and P20 showed the smallest size fractions ranging from fine sand to medium sand. The other study sites ranged from fine sand to medium sand, except the point P8 showed that only the type size medium sand and P19, indicating a particle size of the coarse type. The small correlation of organic matter with the elements studied in this work suggests that these are not of anthropogenic origin but geochemical support

Hidrocarbonetos alifáticos em sedimentos de fundo do estuário do Rio Potengi, grande Natal (RN): implicações ambientais

The Potengi river estuary is located in the region of Natal (RN, Brazil), comprising a population of approximately 1,000,000 inhabitants. Besides the dominant urban presence, the estuary has fragments of mangrove forest. The objective of this study is to determine the aliphatic hydrocarbons found in the bottom sediments of this estuary, identifying their levels, distribution and their possible origins through the diagnostic rates, indexes and results comparisons with the local anthropic and natural characteristics. The samples were obtained according to a plan that allowed sampling of the estuary up to 12 km upstream from it as mounth. 36 stations were selected, grouped into 12 cross sections through the course of the river and spaced on average by 1 km. Each section consisted of three stations: the right margin, the deepest point and the left margin. The hydrocarbon n-alkanes from C10 to C36, the isoprenoids pristane and phytane, the unresolved complex mixture (UCM) and the total resolved hydrocarbons were analyzed by gas chromatography. N-alkanes, pristane, phytane and UCM were detected only at some stations. In the other, the concentration was below the detection limit defined by the analytical method (0.1 mg / kg), preventing them from being analyzed to determine the origin of the material found. By using different parameters, the results show that the estuary receives both the input of petrogenic hydrocarbons, but also of biogenic hydrocarbons, featuring a mixture of sources and relatively impacted portions. Based on the characteristics and activities found in the region, it is possible to affirm that petrogenic sources related to oil products enter the estuary via urban runoff or boats traffic, boat washing and fueling. Turning to the biogenic source, the predominant origin was terrestrial, characterized by vascular plants, indicating contribution of mangrove vegetation. It was evident the presence of, at specific points in the estuary, hydrocarbon pollution, and, therefore is recommended the adoption of actions aimed at interrupting or, at least, mitigating the sources potentially capable of damp petrogenic hydrocarbons in the estuary studied.

Gestão compartilhada de P&D em petróleo:a interação entre a Petrobrás e a Universidade Federal do Rio Grande do Norte

This work addresses the relationship between University-Firm aims to understand the model of shared management of R&D in petroleum of Petrobras with UFRN. This is a case study which sought to investigate whether the model of cooperation established by the two institutions brings innovation to generate technical-scientific knowledge and contribute to the coordination with other actors in the promotion of technological innovation. In addition to desk research the necessary data for analysis were obtained by sending questionnaires to the coordinators of projects in R&D at the company and university. Also, interviews were conducted with subjects who participated in the study since its inception to the present day. This case study were analysed through the Resource-Based View and Interorganizational Networks theory. The sample data also stands that: searches were aligned to the strategic planning and that 29% of R&D projects have been successful on the scope of the proposed objectives (of which 11% were incorporated into business processes); which was produced technical and scientific knowledge caracterized by hundreds of national and international publications; thesis, dissertations, eleven patents, and radical and incremental innovations; the partnership has also brought benefits to the academic processes induced by the improved infrastructure UFRN and changing the "attitude" of the university (currently with national prominence in research and staff training for the oil sector). As for the model, the technical point of view, although it has some problems, it follows that it is appropriate. From the viewpoint of the management model is criticized for containing an excess of bureaucracy. From the standpoint of strategic allocation of resources from the legal framework needs to be reassessed, because it is focused only on the college level and it is understood that should also reach the high school given the new reality of the oil sector in Brazil. For this it is desirable to add the local government to this partnership. The set of information leads to the conclusion that the model is identified and named as a innovation of organizational arrangement here known as Shared Management of R&D in petroleum of Petrobras with UFRN. It is said that the shared management model it is possible to exist, which is a simple and effective way to manage partnerships between firms and Science and Technology Institutions. It was created by contingencies arising from regulatory stand points and resource dependence. The partnership is the result of a process of Convergence, Construction and Evaluation supported by the tripod Simplicity, Systematization and Continuity, important factors for its consolidation. In practice an organizational arrangement was built to manage innovative university-industry partnership that is defined by a dyadic relationship on two levels (institutional and technical, therefore governance is hybrid), by measuring the quarterly meetings of systematic and standardized financial contribution proportional to the advancement of research. These details have led to the establishment of a point of interaction between the scientific and technological-business dimension, demystifying they are two worlds apart

Proposta de modelo de interação da Universidade Federal do Rio Grande do Norte e empresas do setor de petróleo

Operational procedures may negatively interfere in negotiation and execution regarding universities and business companies. In some cases it may even derail business interaction. Thus, aiming to overcome this and other barriers a university-industry interaction model was structured. The model enhances the appropriation of technological solutions on behalf of enterprises, as well as aim to improve the quality of teaching and research done at the university. In order to conduct a case study, sampling considering the Federal University of Rio Grande do Norte (UFRN) was made as well as the Oil and Gas sector. For data collection questionnaires, classroom observation, document analysis, semi-structured interviews were used. The study describes the companies as well as the internal organization of UFRN in their interaction context. The diagnosis related to past interactions as well as the expectations of the companies and the university s internal subjects regarding the university-industry relationship were also studied. Thus, specific questionnaires were applied for the three types of groups: researchers, managers and business companies. These subjects pointed out that the great deal of barriers they identified were related to issues regarding the university internal management. Given these barriers, the critical factors were then identified in order to overcome this reality. Among the nine critical factors only one belongs to the macro environment, while the remaining factors are related to organizational issues present in the university context. It was possible to formulate a university-business interaction model one the researched focused on the case study results and contribution from a theoretical framework that was enabled trough literature review. The model considers all business collaboration mechanisms; it focuses on a particular strategic productive sector and provides a co-evolution vision over time, according to the sector´s development strategy. The need for institutionalizing the relationship with the companies involved is pointed out. The proposed model considers all the critical factors identified by the research; it aims long-term relationship with the company and integrates teaching, research and extension actions. The model implementation was also considered. It was seen that it must be done in three phases. The phases will be defined by the level of maturity in the relationship between the university and the companies. Thus, a framework was developed in order to assess the interaction level regarding company institutionalization. Whilst structuring the model was a concern with replication came up. It was pointed out that this model should not only serve to this specific case study situation. So the final result is a model of university-industry relationship appropriate in the first instance, for UFRN, but has applicability, in general, to any Brazilian university

Efeito da salinidade, densidade de estocagem e da infecção hipodermal e necrose hematopoiética (IHHN) na imunidade do camarão Litopenaeus vannamei cultivados em fazendas do Rio Grande do Norte

The main problem faced by the shrimp industry are the infectious diseases. The hypodermal and hematopoietic necrosis infection (IHHN) is one of the major cause of disease in the cultured shrimp, Litopenaeus vannamei. Environmental changes involving water quality, oxygen concentration, salinity, temperature, stocking density, presence of pathogens, among others, triggering a stressing condition for the cultured shrimp, weakening them and allowing the outbreak of diseases. The stress on the animal leads to a change in the molecules immune response components, which can be used as indicators of shrimp health. Thus, the objective of the present study was to evaluate the effect of salinity, stocking density and IHHNV infection on the L. vannamei shrimp. The immune parameters used to check the shrimp health were the total hemocytes counts (THC), the agglutinating activity (AA) and the clotting time (CT) of the serum of shrimp. These parameters were analyzed in healthy and IHHNV-infected shrimp, grown in low (0-0.5 ), medium (19-24 ) and high (> 38 ) salinity, and extensive (7-12 cam.m-2), semi-intensive (15-25 cam.m-2) and intensive (33-45 cam.m -2) stocking density. The IHHNV infection rate was significantly higher in low salinity (P<0.005) and intensive density (P<0.005), both stressful conditions for L. vannamei. Low salinity significantly increased THC (P<0.05) and decreased and CT (P<0.05) in healthy and infected shrimp, but AA (P<0.05) significantly decreased in healthy shrimp at medium salinity. Culture intensification did not affect the THC, AA and CT of healthy and infected shrimp (P>0.05). The IHHNV infection did not affect any immune parameters of shrimp cultured at different salinities and stocking densities. It is necessary to emphasize that this study was conducted in shrimp grown in ponds, where several environmental factors are acting simultaneously. Thus, further studies are needed about the influence of other environmental factors on the immune parameters of shrimp cultured in pond

Estrutura da população de Coleodactylus natalensis Freire, 1999 (Squamata: Sphaerodactylidae) no Parque Estadual Dunas de Natal, Rio Grande do Norte, Brasil

Coleodactylus natalensis Freire, 1999, an endemic species of Atlantic Forest fragments around the Natal municipality, Rio Grande do Norte State, Brazil, has as type locality the Parque Estadual Dunas de Natal (05º48 S to 05º53 S and 35º09 W to 35º12 W), one of the largest restinga (herb and shrub association on sand dunes along the Brazilian coastline) associate fragment, surrounded by urban zone, placed on setentrional Atlantic Forest limits. We made estimates on populational density, spatial distribution, habitat and microhabitat preferences and feeding ecological aspects like sazonal and sexual variations on diet, prey electivities and niche breadth. We randomly sampled ninety-six 50m2 quadrants in each of the four habitats identified in the study area. Were collected 49 specimens and their stomach contents were analyzed; prey items found were correlated with leaf-litter invertebrates from habitat samples. We found a 98,5 ± 75,5 individuals/ha density, in grouped distribution pattern on densest habitats and random distribution on others habitats. This species lives mostly on leaf-litter in forest habitats, in higher humidity points, with lower temperatures, deeper leaf litter and lower sea level elevations than the randomly chosen points in the study area. Isopoda and Aranae were the most important prey categories in numeric, frequency and volumetric terms. Niche breadth has an intermediate value and was variable in sexual and in habitat terms. There was no correlation between morfometric measures and prey size on diet. The C. natalensis population studied seems to be diet opportunist, although selects larger prey items. The Parque Estadual das Dunas do Natal has several indications of anthropic pressure from the surrounding urban area that may affects the local C. natalensis population. Thus, the fragility of this species calls for urgent conservation efforts

Flebotomíneos (Diptera: Psychodidae) em um sistema agroflorestal da Região Metropolitana de Natal, Rio Grande do Norte, Brasil

Sandflies stand out as important vectors of leishmaniasis. The females need to ingest blood meals, enabling them to transmit protozoa of the genus Leishmania, which may give rise to visceral leishmaniasis (VL) or American tegumentary leishmaniasis (ATL), in addition to transmitting other parasites. Leishmaniasis are important infirmities, distributed worldwide, whose infection results from the interaction of reservoir animals, the vector insect, parasitic protozoa and the healthy host. In the state of Rio Grande do Norte (RN), Brazil, these insects are important transmitters of VL, which usually presents in the most serious form. It occurs mainly in metropolitan areas, with the dog as its main reservoir and Lutzomyia longipalpis as the vector. ATL is most present in the highland areas of the state. In addition to hematophagia, engaged in by the females, both sexes need to ingest carbohydrates, which are essential to the sand flies energy requirements and may interfere in the development of Leishmania. The aim of this study was to determine the occurrence and abundance of sand flies in different environments on the farm belonging to the Empresa de Pesquisas Agropecuárias do RN (Institute of Agricultural Research of RN), in the municipality of Parnamirim, in order to relate this occurrence with climatological and biological references and eating habits. Three consecutive monthly collections were carried out with CDC traps in a fragment of the Atlantic Forest, in a residence, on a goat breeding farm and on cashew, dwarf and giant coconut, mango, banana, eucalyptus, acacia and bean plantations. A total of 1241 sandflies from eight species (Lutzomyia evandroi, Lutzomyia longipalpis, Lutzomyia shannoni, Lutzomyia sordellii Lutzomyia walkeri, Lutzomyia wellcomei, Lutzomyia whitmani, and Lutzomyia intermedia) were collected, most in the forest environment. L. longipalpis, the main VL transmitter, was confirmed as a species adapted to anthropic environments, whereas others such as L. wellcomei, the vector of ATL, occurred predominantly in forests. Carbohydrate characterization of the sand flies and plants of the region demonstrated that a number of exotic plants such as hay and eucalyptus may play some role in the adaptation of these species to modified environments. Breeding in laboratory showed a mean biological cycle of 53.5 days from egg to adulthood for L. shannoni and the possibility of diapause behavior in L. wellcomei. This study serves as a source of information that may contribute to the epidemiological vigilance of tegumentary and visceral leishmaniasis in the state, given that it analyzes the bioecology of transmitting species, as well as their potential to adapt to new environments

Rubiaceae em um remanescente de floresta atlântica no Rio Grande do Norte, Brasil

Empresa de Pesquisa Agropecuária do Rio Grande do Norte