Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Estudo sobre o efeito dos parâmetros de processamento dos pós e sinterização do aço inox 316l reforçado com NbC

This masther dissertation presents a contribution to the study of 316L stainless steel sintering aiming to study their behavior in the milling process and the effect of isotherm temperature on the microstructure and mechanical properties. The 316L stainless steel is a widely used alloy for their high corrosion resistance property. However its application is limited by the low wear resistance consequence of its low hardness. In previous work we analyzed the effect of sintering additives as NbC and TaC. This study aims at deepening the understanding of sintering, analyzing the effect of grinding on particle size and microstructure and the effect of heating rate and soaking time on the sintered microstructure and on their microhardness. Were milled 316L powders with NbC at 1, 5 and 24 hours respectively. Particulates were characterized by SEM and . Cylindrical samples height and diameter of 5.0 mm were compacted at 700 MPa. The sintering conditions were: heating rate 5, 10 and 15◦C/min, temperature 1000, 1100, 1200, 1290 and 1300◦C, and soaking times of 30 and 60min. The cooling rate was maintained at 25◦C/min. All samples were sintered in a vacuum furnace. The sintered microstructure were characterized by optical and electron microscopy as well as density and microhardness. It was observed that the milling process has an influence on sintering, as well as temperature. The major effect was caused by firing temperature, followed by the grinding and heating rate. In this case, the highest rates correspond to higher sintering.

Análise mecânica e microestrutural das ligas de cobalto-cromo de uso odontológico após sucessivas refundições

The cobalt-chromium alloy is extensively used in the Odontology for the confection of metallic scaffolding in partial removable denture. During the last few years, it has been reported an increasing number of premature imperfections, with a few months of prosthesis use. The manufacture of these components is made in prosthetic laboratories and normally involves recasting, using parts of casting alloy and parts of virgin alloy. Therefore, the objective of the present study was to analyze the mechanical properties of a commercial cobalt-chromium alloy of odontological use after successive recasting, searching information to guide the dental prosthesis laboratories in the correct manipulation of the cobalt-chromium alloy in the process of casting and the possible limits of recasting in the mechanical properties of this material. Seven sample groups were confectioned, each one containing five test bodies, divided in the following way: G1: casting only with virgin alloy; G2: casting with 50% of the alloy of the G1 + 50% of virgin alloy; G3: casting with 50% of the alloy of the G2 + 50% of virgin alloy; G4: casting with 50% of the alloy of the G3 + 50% of virgin alloy; G5: 50% of alloy of the G4 + 50% of virgin alloy; G6: 50% of alloy of the G5 + 50% of virgin alloy and finally the G7, only with recasting alloy. The modifications in the mechanical behavior of the alloy were evaluated. Moreover, it was carried the micro structural characterization of the material by optic and electronic scanning microscopy, and X ray diffraction.and fluorescence looking into the correlatation of the mechanical alterations with structural modifications of the material caused by successive recasting process. Generally the results showed alterations in the fracture energy of the alloy after successive recasting, resulting mainly of the increasing presence of pores and large voids, characteristic of the casting material. Thus, the interpretation of the results showed that the material did not reveal significant differences with respect to the tensile strength or elastic limit, as a function of successive recasting. The elastic modulus increased from the third recasting cycle on, indicating that the material can be recast only twice. The fracture energy of the material decreased, as the number of recasting cycles increased. With respect to the microhardness, the statistical analyses showedno significant differences. Electronic scanning microscopy revealed the presence of imperfections and defects, resulting of the recasting process. X ray diffraction and fluorescence did not show alterations in the composition of the alloy or the formation of crystalline phases between the analyzed groups. The optical micrographs showed an increasing number of voids and porosity as the material was recast. Therefore, the general conclusion of this study is that the successive recasting of of Co-Cr alloys affects the mechanical properties of the material, consequently leading to the failure of the prosthetic work. Based on the results, the best recommendadition is that the use of the material should be limited to two recasting cycles

Efeito das variáveis laboratoriais protéticas na adesão da porcelana com ligas de níquel-cromo

The metalceramic crowns are usually used in dentistry because they provide a resistant structure due to its metallic base and its aesthetics from the porcelain that recovers this structure. To manufacture these crowns, a series of stages should be accomplished in the prosthetic laboratories, and many variables can influence its success. Changes in these variables cause alterations in the metallic alloy and in the porcelain, so, as consequence, in the adhesion between them. The composition of the metal alloy can be modified by recasting alloys, a common practice in some prosthetic laboratories. The aim of this paper is to make a systematic study investigating metalceramic crowns as well as analyzing the effect of recasting Ni-Cr alloys. Another variable which can influence the mechanism of metalceramic union is the temperature used in firing porcelain procedure. Each porcelain has to be fired in a fixed temperature which is determined by the manufacturer and its change can cause serious damages. This research simulate situations that may occur on laboratory procedures and observe their consequences in the quality of the metalceramic union. A scanning eletron microscopy and an optic microscopy were accomplish to analyse the metal-ceramic interface. No differences have been found when remelting alloys were used. The microhardness were similar in Ni-Cr alloys casted once, twice and three times. A wettability test was accomplished using a software developed at the Laboratório de Processamento de Materiais por Plasma, on the Universidade Federal do Rio Grande do Norte. No differences were found in the contact angle between the solid surface (metallic substratum) and the tangencial plane to the liquid surface (opaque). To analyse if the temperature of porcelain firing procedure could influence the contact area between metal and porcelain, a variation in its final temperature was achieve from 980° to 955°C. Once more, no differences have been found

Estudo da molhabilidade de ligas de adição à base de prata sobre insertos cerâmicos para aplicação em brocas perfuração de poços de petróleo

Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Estudo da influência da temperatura de brasagem nas uniões zircônia/aço inox 304 utilizando metalização mecânica

Metal-Ceramic (M/C) Zirconia-stainless steel interfaces have been processed through brazing techniques due to the excellent combination of properties such as high temperature stability, high corrosion resistance and good mechanical properties. However, some M/C interfaces show some defects, like porosity and cracks results in the degradation of the interfaces, leading even to its total rupture. Most of time, those defects are associated with an improper brazing parameters selection to the M/C system. In this work, ZrO2 Y-TZP and ZrO2 Mg - PSZ were joint with the stainless steel grade 304 by brazing using a eutectic silver-copper (Ag28Cu) interlayer alloy with different thermal cycles. Ceramic surfaces were previous mechanically metallized with titanium to improve adhesion of the system. The effect of temperature on the M/C interface was studied. SEM-EDS and 3 point flexural bend test were performed to evaluate morphology, chemical composition and mechanical resistance of the M/C interfaces. Lower thermal cycle temperatures produced better results of mechanical resistance, and more regular/ homogeneous reaction layers between braze alloy and metal-ceramic surfaces. Also was proved the AgCu braze alloy activation in situ by titanium

Aplicação de técnicas eletroquímicas na determinação do potencial de corrosividade de ligas de alumínio em água produzida

The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed

Análise da Expressão de APE1 após Estresse Oxidativo Induzido em Células Proficientes e Deficientes na Via de Reparo por Excisão de Nucleotídeos

Riboflavin is a vitamin very important in aerobic organisms, as a precursor of many coenzymes involved in the electron transporter chain. However, after photosensitization of riboflavin with UV or visible light, it generates reactive oxygen species (ROS), which can oxidize the DNA. The repair of oxidative lesions on DNA occurs through the base excision repair pathway (BER), where APE1 endonuclease plays a central role. On the other hand, the nucleotide excision repair pathway (NER) repairs helix-distorting lesions. Recently, it was described the participation of NERproteins in the repair of oxidative damage and in stimulation of repair function fromAPE1. The aim of this research was to evaluate the cytotoxic effects of photosensitized riboflavin (RF*) in cells proficient and deficient in NER, correlating with APE1 expression. For this propose, the cells were treated with RF* and it was performed the cell viability assay, extraction of whole proteins, cells fractionation, immunoblotting, indirect immunofluorescence and analysis of polymorphisms of BER gens. The results evidenced that cells deficient in XPA and CSB proteins were more sensitive to RF*. However, XPC-deficient cells presented similar resistance to MRC5- SV cells, which is proficient in NER. These results indicate that XPA and CSB proteins have an important role on repair of oxidative lesions induced by RF*. Additionally, it was evidenced that single nucleotide polymorphisms (SNPs) in BER enzymes may influence in sensitivity of NER-deficient cell lines. Concerning the APE1 expression, the results showed that expression of this protein after treatment with RF* only changed in XPC-deficient cells. Though, it was observed that APE1 is recruited and is bound to chromatin in MRC5-SV and XPA cells after treatment with RF*. The results also showed the induction of DNA damage after treatment with RF*, through the analysis of-H2AX, since the treatment promoted an increase of endogenous levels of this phosphorylated protein, which acts signaling double strand-break on DNA. On the other hand, in XPC-deficient cells, regardless of resistance of RF*, the endogenous levels of APE1 are extremely reduced when compared with other cell lines and APE1 is not bound to chromatin after treatment with RF*. These results conclude that RF* was able to induce cell death in NERdeficient cells, where XPA and CSB cells were more sensitive when compared with MRC5-SV and XPC-deficient cells. This last result is potentially very interesting, since XPC-deficient cell line presents low levels of APE1. Additionally, the results evidenced that APE1 protein can be involved in the repair of oxidative damage induced by RF*, because APE1 is recruited and bound strongly to chromatin after treatment.

Influência da esplenectomia na biodistribuição do ácido dimercaptosuccínico-tecnécio-99m (99mTc-DMSA) em ratos Wistar

A esplenectomia é indicada em doenças hematológicas, hiperesplenismo grave, traumas e tem sido causa de importantes alterações metabólicas e imunológicas. O objetivo do presente trabalho é avaliar se a retirada do baço altera a biodistribuição do radiofármaco DMSA Tc99m em ratos Wistar e se há correlação com possíveis alterações da função renal. Foram usados dois grupos: esplenectomia (n=6) e controle (n=6) animais não operados. Após 15 dias, foi administrado 0,1 ml de DMSA-Tc99m via plexo orbital (0,66 MBq). Trinta minutos depois, foram retiradas amostras do rim, coração, pulmão, tireóide, estômago, bexiga, fêmur, sangue. Após pesadas as amostras, foi determinado o percentual de radioatividade/g (% ATI/g) em cada uma delas, com o Wizard Gama Counter Perkin-Elmer . Dosadas uréia e creatinina sérica, hematócrito, plaquetas e leucócitos. Estatística pelo teste t, com significância 0,05. Foi observada redução significante no %ATI/g no rim e sangue (p<0,05) dos animais esplenectomizados, aumento significante (p<0,05) da uréia (88,8±18,6mg/dL) e creatinina (0,56±0,08), comparado aos controles (51,5±1,6 e 0,37±0,02mg/dL, respectivamente) assim como leucocitose, aumento de plaquetas e redução de hematócrito. Em conclusão, a esplenectomia provocou comprometimento da função renal, repercutindo na alteração da captação de DMSA 99mTc pelo rim de ratos. Uma parceria entre a Unidade de Medicina Nuclear da Liga Norteriograndense Contra o Câncer e o Núcleo de Cirurgia Experimental da Universidade Federal do Rio Grande doNorte tornou possível a realização deste trabalho, que contou com a participação de profissionais de diferentes áreas como: Biologia, Biomedicina, Medicina Nuclear, Cirurgia Geral, Bioquímica e Estatística, atestando dessa forma o caráter multidisciplinar do trabalho

Avaliação das atividades antinociceptiva e anti-inflamatória de uma heterofucana da alga Dictyota menstrualis

Fucana é um termo que define uma família de hetero e homopolissacarídeos que contem L-fucose em sua estrutura. Neste trabalho uma hererofucan F 2,0v da alga Dictyota menstrualis foi avaliada como agente antinociceptivo e antiinflamatório. A fucana F 2,0v inibiu a migração de leucócitos em até 100% (20.0 mg/kg) para a cavidade peritoneal após estimulo químico, porém, não alterou a expressão das interleucinas IL-1β, IL-6 e de TNF-α. Com relação a sensação dolorosa a F 2,0v (20.0 mg/kg) possui atividade antinociceptiva periférica com potência semelhante à dipirona. Por outro lado não apresentou efeito no teste da placa quente. Análises de microscopia confocal e citometria de fluxo mostram que a F 2,0v se liga a superfície dos leucócitos. O conjunto de resultados apresentados pela fucana F 2,0v sugerem que o mecanismo de ação está relacionado com sua capacidade de inibir a migração de leucócitos para o local da injúria tecidual. Em resumo os dados mostram que F 2,0v apresenta grande potencial como composto antinociceptivo e antiinflamatório. Estudos futuros serão realizados para caracterizar melhor o mecanismo de ação da F 2,0v

Biodistribuição do pertecnetato de sódio após cirurgia do Switch Duodenal

The biliopancretic diversion with duodenal switch is one of the mixing techniques used in the treatment of morbid obesity. The duodenal switch reduces the stomach capacity and leaves only 50-100 cm of small intestine for nutrition and absorption. The surgery produces hormonal, structural and biochemical changes, which can influence on the result of scintigraphic examinations in operated patients. With the objective of evaluate the postoperative biodistribution of sodium pertechnetate (Na99mTcO4) in brain, thyroid, heart, lung, liver, spleen, kidney, stomach, duodenum, pancreas, small intestine, bladder, muscle and bone of Wistar rats. The rats were randomly allocated into 3 groups of 7 rats each: the duodenal switch group (DS), the control group (C) and the sham group (S). They were operated under anesthesia and aseptic technique. In the tenth postoperative day, 0.1mL of sodium pertechnetate was injected via orbital plexus. After 30 min the animals were killed with overdose of anesthetic and samples of liver, spleen, pancreas, stomach, duodenum, small intestine, thyroid, lung, heart, kidney, bladder, muscle, bone and brain were harvested, washed with saline and weighed. The detention of radioactivity was made using the automatic Gamma Counter Wizard, PerkinElmer and the percentage of activity per gram of tissue (%ATI/g) was calculated. There was no early or late mortality in either rats groups. The values of percent radioactivity per gram of tissue (%ATI/g), showed no significant difference in liver, stomach, small bowel, duodenum, kidney, heart, bladder, bone and brain, when compared the DS rats with sham and controls rats. A postoperative significant increase in mean %ATI/g levels was observed in spleen, pancreas and muscle in group DS rats, as compared to group S and C rats (p<0.05). In the lung there was an increase and in thyroid a decrease in mean %ATI/g of DS rats, when compared to sham rats (p>0.05). In conclusion, the biliopancreatic diversion with duodenal switch in rats modified the biodistribution of sodium pertechnetate in thyroid, lung, pancreas, spleen and muscle. The study had the participation of the departments and laboratories researches, as Nucleus of Experimental Surgery, Department of Surgery, Laboratory of Radiobiology, Department of Pathology and Service of Nuclear Medicine, certifying the character of a multidisciplinary research

Capital social e igreja católica :expressões e práticas no sertão do Seridó

It historizes and it analyzes the social capital in the area Seridó. The traditions associative seridoenses are reconstructed starting from the dimensions: economical, social, religious person and politics. In them it is possible to notice actions that form the social capital of the area. The country of Seridó present an associative tradition based on the mutual help, in the trust and reciprocity that she remount there are decades in your history. The relationship among the Catholic Church, that historically it is present in the area, and rural communities, through your community associations, it is the backdrop where you/they are the responsible associative elements for the tear of the regional social fabric: in him (the backdrop) he/she is the responsible social capital for the work of the rural community organizations. The Catholic Church, through your social action and the Program of Combat to the Rural Poverty, of Rio Grande do Norte is the league that sustains the actions collective seridoenses

Testemunhos de um tempo vivido : fragmentos e contextos de uma narrativa de Janduís-RN

Shows up the memory of the elderly, as a consistent experience in the in the construction of the social memory of Janduís, Rio Grande do Norte, where the research takes place. Through an autobiographic narrative, in a qualitative approaching, the intent is to stand up aspects about the individual history and collective memories, starting in a simple question: what did they remember? A question that turns into many others, as how the remember and under which circumstances. So, the lived and remembered moments are the subject of this paper, as these testimonials shows and reveals the citizens typical aspects, intending to telling (again) the city s history by the memories of this people. By oral statements and the analysis that followed, subjective aspects that made a social memory, highlight in violent episodes, that, now remembered, occurred in the historical sediment, which connects several social times, establishing a narrative standard. In Janduís, this standard is about the memory that sticks out their individual ways, and the collective life, in the past, standing out the fair and the events that occurred on it, as the most remembered place, where the memories go stronger. When they narrate are incorporated others facts, the story is reinvented, connecting the past to the future. The paper also revels builders subjects aspects of a social memory, as historical sediment that joins the social times. At the present moment, the fair, to them, is a place that doesn t exist anymore; for the city, is a place of enlargement of women s presence at the trending spaces, which means a place of social transformation. That being said, the fair, in both times, present and past, turns into a analysis object, with important elements to reference narrative s time and place. And how the narrative update the past recorded in the old citizen s memory. What was intended to do was articulate the memory and the history form temporal and special etching that define the place and the narrative context: the lived and the remembered at the group s day by day. In that way, were identify the collective memory s common elements, enunciating the memory and the narratives that update that history, influencing and being influenced, forming in memories in a collective phenomenon fueling the local imaginary

Fazer a ponte para a escola de todos(as)

The purpose of this study is to understand what are the matrix elements in which everyday activities of social author/authors, actor/actors and actress/actresses are embedded, in order to carry out the Escola da Ponte s political and pedagogic process (PPP). Thus, the object of this study is to reflect on an experience developed in a public school supported by the Portuguese State within the scenario of institutions that are committed to building up a school of the people by investing in democratization and community participation in their management process. The methodological course of action was targeted at the presuppositions of qualitative research (WOODS, 1999; BURGESS, 1997; MILLS, 1982; OLIVEIRA, 1998; BOGDAN and BIKLEN, 1994; MACEDO, 2000; CASAL, 1996; GEERTZ, 2000), with data collected from random word association (MACHADO and CARVALHO, 2003), the discourse of the interviewed (KAUFMANN, 1996; SILVA, 2006; 2002), observation notes and documents (ELIAS, 1997). Based on a multiple reference and theoretical framework, the investigation revealed elements that are construed as the raw material and pillars supporting the bridge of a school of the people, as well as the self-organization of the school community which emerges as a dimension that binds together all the elements and brings new arrangements into the school dynamics by moving from the individual to the society (DUPUY, 1990). Along this line, the central argument is that in the short and long run the public school quality does not spring from macro educational policies, nor from ephemeral mass-production programs, projects or governmental policies, but from the intent of the professionals working there in becoming authors and characters in the process of building up and carrying out the PPP. The Project has been conceived in the light of the needs and intentionality of the community whose support comes from the participation and social control held by the students families and the community s power to force to action public administration central agencies aiming at having the State fulfill its responsibilities