Crystallographic and spectroscopic studies on palladium(II) complexes containing pyrazole and thiocyanate ligands

Mononuclear palladium(II) complexes containing both pyrazole-type ligands and thiocyanate, of general formula [Pd(SCN) 2(L) 2] {L = pyrazole (HPz) and l-phenyl-3-methylpyrazole (phmPz)} have been prepared and characterized by elemental analysis, i.r. and n.m.r. spectroscopy and by single crystal X-ray diffraction methods. The Pd atom in these structures lies on the crystallographic inversion center; in a square-planar coordination geometry made by two sulfur and two nitrogen atoms of the ligands, both in trans positions.

Possible effects of sodium chloride treatment on quality of effluents from Alabama channel Catfish ponds

Channel catfish ponds are treated with salt (sodium chloride) to increase chloride concentration and prevent nitrite toxicity in fish. A survey indicated that most farmers try to maintain chloride concentration of 50 to 100 mg/L in ponds by annual salt applications. Averages and standard deviations for selected water quality variables in salt-treated ponds were as follows: chloride, 87.2 ± 37.5 mg/L; total dissolved solids (TDS), 336 ± 96 mg/L; specific conductance, 512 ± 164 μmhos/cm. Maximum values were 189 mg/L for chloride, 481 mg/L for TDS, and 825 μmhos/cm for specific conductance. Good correlations between specific conductance values and both chloride and TDS concentrations suggest that specific conductance can be a rapid method for estimating concentrations of these two variables in surface water. The maximum limit for chloride concentration in Alabama streams allowed by the Alabama Department of Environmental Management is 230 mg/L. The usual recommended upper limit of TDS for protection of aquatic life in freshwater streams is 1,000 mg/L. Based on the observed relationship between TDS concentration and specific conductance in Alabama catfish ponds, 1,000 mg/L TDS corresponds to 1,733 μmhos/cm specific conductance. It is unlikely that effluents from salt-treated catfish ponds would violate the in-stream chloride standard of 230 mg/L or harm aquatic life in streams. Nevertheless, chloride concentrations in ponds should be measured before salt application as a safe guard against excessive salt application and chloride concentrations above the in-stream chloride standard.

Habitat, distribuição e aspectos adaptativos de peixes da microbacia do ribeirão Grande, Estado de São Paulo, Brasil

The ichthyofauna of ribeirão Grande microbasin that runs through one of the few remaining fragments of Atlantic Forest (in Mantiqueira mountain range, Valley of Paraíba) was studied. Fish samples were obtained with an electric fishing powered by a maximum capacity generator of 155 V and 60-Hz alterning current, gill-nets and traps. In three collecting days, during July/2001, October/2001, January/2002 and April/2002, 2865 fishes were sampled. These fishes belonged to 12 families, 23 genera and 37 species. The species were more abundant between the piedmont and the plain of the Valley of Paraíba. The Characidium, Trichomycterus genera and the Imparfinis minutus species presented only one ovary or testis and no swim bladder. The ecological significance of morphological features in stream mountain fishes was used to predict the niche adaptation for those conditions, towards K-strategy.

Robust control applications for smart truss structure

A finite element modeling of an intelligent truss structure with piezoelectric stack actuators for the purpose of active damping and structural vibration attenuation is presented. This paper concerns with the following issues aspects: the design of intelligent truss structure considering electro-mechanical coupling between the host structure and piezoelectric stack actuators; the H 2 norm approach to search for optimal placement of actuators and sensors; and finally some aspects in robust control techniques. The electro-mechanical behavior of piezoelectric elements is directly related to the successful application of the actuators in truss structures. In order to achieve the desired damping in the interested bandwidth frequency it is used the H ∞ output feedback solved by convex optimization. The constraints to be reached are written by linear matrix inequalities (LMI). The paper concludes with a numerical example, using Matlab and Simulink, in a cantilevered, 2-bay space truss structure. The results demonstrated the approach applicability.

Identification of structural parameters for active vibration control

The study of algorithms for active vibration control in flexible structures became an area of enormous interest for some researchers due to the innumerable requirements for better performance in mechanical systems, as for instance, aircrafts and aerospace structures. Intelligent systems, constituted for a base structure with sensors and actuators connected, are capable to guarantee the demanded conditions, through the application of diverse types of controllers. For the project of active controllers it is necessary, in general, to know a mathematical model that enable the representation in the space of states, preferential in modal coordinates to permit the truncation of the system and reduction in the order of the controllers. For practical applications of engineering, some mathematical models based in discrete-time systems cannot represent the physical problem, therefore, techniques of identification of system parameters must be used. The techniques of identification of parameters determine the unknown values through the manipulation of the input (disturbance) and output (response) signals of the system. Recently, some methods have been proposed to solve identification problems although, none of them can be considered as being universally appropriate to all the situations. This paper is addressed to an application of linear quadratic regulator controller in a structure where the damping, stiffness and mass matrices were identified through Chebyshev's polynomial functions.

Cytogenetic and random amplified polymorphic DNA analysis of Leptodactylus species from rural and urban environments (Anura, Amphibia)

Cytogenetic and random amplified polymorphic DNA analyses carried out in the species Leptodactylus podicipinus, L. ocellatus, L. labyrinthicus, and L. fuscus from rural and urban habitats of the northwest region of São Paulo State, Brazil, showed that the karyotypes (2n = 22), constitutive heterochromatin distribution and nucleolus organizer region (NOR) location did not differ between the populations from the two environments. The in situ hybridization with an rDNA probe confirmed the location of the NORs on chromosome 8 revealing an in tandem duplication of that region in one of the chromosomes of L. fuscus. DAPI showed that part of the C-band-positive heterochromatin is rich in AT, including that in the proximity the NORs in L. podicipinus and L. ocellatus. The molecular analyses showed that the two populations (urban and rural) of L. podicipinus and L. fuscus are similar from a genetic point of view. The urban and rural populations of species L. ocellatus and L. labyrinthicus showed differences in genetic structures, probably due to urbanization which interferes with the dispersion of those frogs. The marked differences observed between the two populations of L. ocellatus can be representing the cryptic condition of the species. Unweighted pair-group method of analysis and genetic distance analysis detected the genetic proximity between L. ocellatus and L. fuscus. The results indicate that there was no reduction in the genetic diversity in the populations from the urban environment; however, the survival of these frogs would not be guaranteed in the case of an increase in human impact especially for populations of L. labyrinthicus and L. ocellatus. ©FUNPEC-RP.

Caracterização das falhas de transferência na porção norte da Bacia de Santos a partir da integração de dados geológicos e geofísicos

Structures transverse/sub-transverse to the shoreline have been identified and characterized on the precambrian basement outcrop on the continent adjacent to the northern Santos Basin. These structures were analyzed from images of digital elevation model SRTM 90m by extracting NW-SE lineaments that intersect the NE-SW foliation. The lineaments were selected, classified into 48 segments that extend toward offshore, and correlated with basin structures. In the basin 25 2D seismic sections, 12 well logs and data from potential methods were interpreted, identifying the key stratigraphic levels and the major structures. Structural maps of each horizon were generated. Six transfer faults (FTs) were recognized and named FT-1 to FT-6, whose extensions correspond to continental lineaments named FC1 to FC6. The FTs are related to the basin deformation and evolution. In seismic sections, these faults have lateral slip in flower structures, displacement inversions from normal at the top to reverse at the base, abrupt changes in thickness or even disappearance of the seismic reflectors. The structural map of the Basement and Top of the Rift shows control of some depocenters by faults and displacements in some areas. The maps of potential methods indicate that there are pronounced anomaly shifts in some areas, associated with FTs. Some seismic sections indicate reactivation of FTs when they intersect horizons from the basement until the most recent layers. The 3D integration of data facilitated the observation of the FT extensions in the continent discontinuity.

Social Panorama of Latin America 2004

Includes bibliography

Structural real time control using fluid magnetorheologic damper

In the last decades there was a great development in the study of control systems to attenuate the harmful effect of natural events in great structures, as buildings and bridges. Magnetorheological fluid (MR), that is an intelligent material, has been considered in many proposals of project for these controllers. This work presents the controller design using feedback of states through LMI (Linear Matrix Inequalities) approach. The experimental test were carried out in a structure with two degrees of freedom with a connected shock absorber MR. Experimental tests were realized in order to specify the features of this semi-active controller. In this case, there exist states that are not measurable, so the feedback of the states involves the project of an estimator. The coupling of the MR damper causes a variation in dynamics properties, so an identification methods, based on experimental input/output signal was used to compare with the numerical application. The identification method of Prediction Error Methods - (PEM) was used to find the physical characteristics of the system through realization in modal space of states. This proposal allows the project of a semi-active control, where the main characteristic is the possibility of the variation of the damping coefficient.

Evolução geológica dos batólitos granitóides neoproterozóicos do sudeste do estado de são paulo

The Neoproterozoic granitogenesis related to the Central Mantiqueira Province comprise the calc alkaline to alkaline granitoid complexes of Sorocaba, San Francisco, São Roque, Ibiúna and Piedade. These complexes occur in a ruptil tectonic to tardi (Sn+3) event. The emplacement of the different facies in transtractives structures of the pull-apart type are characterized in the area by the main transcurrent shear zones of Taxaquara-Pirapora, Itu-Jundiuvira, Moreiras, Cangüera and Caucáia of ENE-WSW general direction. The massifs present complex internal architecture characterized by intrusions in restrict initial phase of intermediate equigranular nature. Also present a main phase of porfiroid monzo and sienogranite that fragments the previous phase, followed by lateral accretion of equi to inequigranular material, and in some cases by the accretion of late phases of circular bodies of porfiroid rapakivi granites, and a late to final phase of aplitic to pegmatitic composition. This magmatism grew with the intrusions of successive magmatic pulses, partially controlled by many reactivations of the shear zones. The REE also suggest that the magmatic phases are similar, synchronous and repetitive in four of the complexes in both domains, present in the São Francisco Complex. The crystallization starts from accretion processes, but compositionally quite different from the others. The variation in compositions and ages (TDM) for these granites reflect the derivation from different sources developed under different magmatic conditions, followed by processes of contamination that frequently occur in the crust.

Condiciones generales de competencia en Guatemala

Incluye Bibliografía

Dependência estrutural da capacidade de rotação plástic em vigas de concreto armado

Summary In this work the structural dependence of plastic rotation capacity in RC beams is evaluated using the Finite Element Method. The objective is to achieve a better understanding of the non-linear behavior of reinforced concrete members and perform extensive parameter studies, using a rational model developed by Bigaj [1] to analyze the phenomenon of plastic rotation capacity in reinforced concrete members. It is assumed that only bending failure is relevant due to sufficient member resistance against shear and torsion. The paper begins with the physical and theoretical background of the phenomenon of plastic hinge development in RC structures. Special emphasis is laid on the issue of structural dependence of deformation capacity of plastic hinges in RC members. Member size dependence and influence of properties of construction materials were emphasized as well. The essential components of the Bigajs model for calculating the plastic rotation capacity are discussed. The behaviour of the plastic hinge is analysed taking into account the strain localisation in the damage zones of the hinge region. The Fictitious Crack Model (FCM) and the Compressive Damage Zone Model (CDZ) are adopted in a Fracture Mechanics approach to model the behaviour of concrete in tension and compression, respectively. The approach is implemented in FEMOOP, a FEM in-house solver under development, and applied to evaluate ductility in 2D beams. The models were generated with GiD, a pre-processor and post-processor developed by CIMNE, and analyzed with the capabilities implemented in FEMOOP. © Universitat Politècnica de Catalunya, Barcelona, España 2010.

Evaluation of skin hydration after exposition to the aqueous and hydroalcoholic bases and silicone emulsion

Several dermocosmetic bases even without active substances, can increase the cutaneous hydration, resulting in a beneficial effect to the skin. The evidence and interpretation of possible hydration effect of formulations in the skin can be carried through by means of histopathological and histomorphometrical evaluation, a time that allows the analysis of the epithelial tissue, of dermis and also of the cellular characteristics. The objective of this research was to evaluate the skin hydration after exposition to the aqueous and hydroalcoholic bases and silicone emulsion. Swines had areas submitted to treatments during 15 days with three different formulations (F1 - aqueous gel, F2 - hydroalcoholic gel and F3 - silicone emulsion). By means of histometric and histopathological techniques were gotten the thickness of the epidermis and stratum corneum. Comparison of means was done using ANOVA followed by the Tukey test. The F1 provoked significant increase in the thickness of the epidermis. The formulaton F2 provoked significant reduction in the thickness of the epidermis and stratum corneum. F3 not presented significant difference in this structures. According to the study, the type of base chosen intervenes with the skin hydration.

Toxicological and histopathological effects of hydramethylnon on Atta sexdens rubropilosa (Hymenoptera: Formicidae) workers

The leaf-cut ants are important agricultural pest, because they can cause intense defoliation in plants and destroy large areas cultivated. Although there are several works for the control of these insects by examining the toxicity of natural chemical compounds on various species of ants, few are focused on analyses of morphological changes caused in the affected organs. The aim of this study was to evaluate the effects of hydramethylnon on Atta sexdens rubropilosa workers through toxicological bioassays and morphological analysis of the post-pharyngeal glands, midgut, and Malpighian tubules of these ants. Hydramethylnon dissolved either in acetone (HA) or in a mixture of acetone and soy oil (HAO) was added to the artificial diet at a concentration of 200 μg/mL. The workers fed daily with the diet containing hydramethylnon showed higher mortality than the controls, especially when HAO was used. Moreover, light and electron microscopy revealed morphological alterations in the midgut and Malpighian tubules of workers treated with HA, whereas alterations of the post-pharyngeal glands were observed in the HAO-treated group. These results indicated that the presence of soy oil provided an alternate route for the ingestion of the formicide's active ingredient and corroborated previous studies that suggested a role for the post-pharyngeal glands in lipid metabolism. Our findings suggest that the oil may carry hydramethylnon to the gland lumen, resulting in lower quantity of the active ingredient in the intestinal lumen and Malpighian tubules that explains the lower degree of morphological alterations in these structures in the workers treated with HAO. These results may provide insight into the toxicological effects of hydramethylnon on leaf-cutting ants and the use of vegetable oil as an adjuvant in baits to control ants. © 2012 Elsevier Ltd.

Comparative feeding kinematics of tropical hylid tadpoles

Anuran larvae, which are otherwise simple in shape, typically have complex keratinized mouthparts (i.e. labial teeth and jaw sheaths) that allow them to graze upon surfaces. The diversity in these structures among species presumably reflects specializations that allow for maximal feeding efficiency on different types of food. However, we lack a general understanding of how these oral structures function during feeding. We used high-speed digital imaging (500 Hz) to observe tadpoles of six species from the anuran family Hylidae grazing on a standardized food-covered substrate. Tadpoles of these species vary in the number of labial tooth rows, belong to two different feeding guilds (benthic and nektonic), and inhabit ponds and streams. We confirmed that the labial teeth in these species serve two functions: anchoring the mouth to the substrate and raking material off of the substrate. In general, tadpoles with a larger maximum gape or those with fewer labial tooth rows opened and closed their mouths slower than tadpoles with smaller gape or more tooth rows. Nektonic feeding tadpoles released each of their tooth rows proportionally earlier in the gape cycle compared with benthic feeding tadpoles. Lastly, we found some support for the idea that deformation of the jaw sheaths during a feeding cycle is predictable based on tadpole feeding guild. Collectively, our data show that anatomical (e.g. number of labial teeth) and ecological features (e.g. feeding guild) of tadpoles significantly influence how tadpoles open and close their mouths during feeding. © 2013. Published by The Company of Biologists Ltd.