The effect of flow regimes in the distillation of systems containing two liquid phases

Single phase solutions containing three components have been observed to exhibit foaminess near a single to two liquid phase boundary. It was seen, in a sintered plate column under mass transfer conditions, that distillation systems where the liquid appeared as one phase in one part of a column and two phases in another part, exhibited foaminess when the liquid concentration was near the one phase to two phase boundary. Various ternary systems have been studied in a 50 plate. 30mm i.d. Oldershaw column and it was observed that severe foaming occurred in the middle section of the column near the one liquid phase to two liquid phase boundary and no foaming occurred at the end of the column where liquid was either one phase or two phase. This is known as Ross type foam. Mass transfer experiments with Ross type ternary systems have been carried out in a perspex simulator with small and large hole diameter trays. It was observed that by removal of the more volatile component, Ross type foam did not build up on the tray. Severe entrainment of liquid was observed in all cases leading to a 'dry' tray, even with a low free area small diameter hole tray which was expected to produce a bubbly mixture. Entrainment was more severe for high gas superficial velocities and large hole diameters. This behaviour is quite different from the build up of foam observed when one liquid phase/two liquid phase Ross systems were contacted with air above a small sintered disc or with vapour in an Oldershaw distillation column. This observation explains why distillation columns processing mixtures which change from one liquid phase to two liquid phases (or vice versa) must be severely derated to avoid flooding. Single liquid phase holdups at the spray to bubbly transition were measured using a perspex simulator similar to that of Porter & Wong (17). i.e. with no liquid cross flow. A light transmission technique was used to measure the transition from spray regime to bubbly regime. The effect of tray thickness and the ratio of hole diameter to tray thickness on the transition was evaluated using trays of the same hole diameter and free area but having thickness of 2.38 mm, 4 mm, and 6.35 mm. The liquid holdup at the transition was less with the thin metal trays. This result may be interpreted by the theory of Lockett (101), which predicts the transition liquid holdup in terms of the angle of the gas iet leaving the holes in the sieve plate. All the existing correlations have been compared and none were found to be satisfactory and these correlations have been modified in view of the experimental results obtained. A new correlation has been proposed which takes into account the effect of the hole diameter to tray thickness ratio on the transition and good agreement was obtained between the experimental results and the correlated values of the liquid holdup at the transition. Results have been obtained for two immiscible liquids [kerosene and water] on trays to determine whether foaming can be eliminated by operating in the spray regime. Kerosene was added to a fixed volume of water or water was added to a fixed volume of kerosene. In both cases, there was a transition from spray to bubbly. In the water fixed system. the liquid holdup at the transition was slightly less than the pure kerosene system. Whilst for the kerosene fixed system, the transition occurred at much lower liquid holdups. Trends In the results were similar to those for single liquid phase. New correlations have been proposed for the two cases. It has been found that Ross type foams, observed in a sintered plate column and in the Oldershaw column can be eliminated by either carrying out the separation in a packed column or by the addition of defoaming additives.

Computer aided manufacturing of geometric models

As systems for computer-aided-design and production of mechanical parts have developed, there has arisen a need for techniques for the comprehensive description of the desired part, including its 3-D shape. The creation and manipulation of shapes is generally known as geometric modelling. It is desirable that links be established between geometric modellers and machining programs. Currently, unbounded APT and some bounded geometry systems are being widely used in manufacturing industry for machining operations such as: milling, drilling, boring and turning, applied mainly to engineering parts. APT systems, however, are presently only linked to wire-frame drafting systems. The combination of a geometric modeller and APT will provide a powerful manufacturing system for industry from the initial design right through part manufacture using NC machines. This thesis describes a recently developed interface (ROMAPT) between a bounded geometry modeller (ROMULUS) and an unbounded NC processor (APT). A new set of theoretical functions and practical algorithms for the computer aided manufacturing of 3D solid geometric model has been investigated. This work has led to the development of a sophisticated computer program, ROMAPT, which provides a new link between CAD (in form of a goemetric modeller ROMULUS) and CAM (in form of the APT NC system). ROMAPT has been used to machine some engineering prototypes successfully both in soft foam material and aluminium. It has been demonstrated above that the theory and algorithms developed by the author for the development of computer aided manufacturing of 3D solid modelling are both valid and applicable. ROMAPT allows the full potential of a solid geometric modeller (ROMULUS) to be further exploited for NC applications without requiring major investment in new NC processor. ROMAPT supports output in APT-AC, APT4 and the CAM-I SSRI NC languages.

The functional effects of ceramide on the monocyte CD36 scavenger receptor and NADPH oxidase

Atherosclerosis is the principal cause of death in the United States, Europe and much of Asia. During the last decade, inflammation has been suggested to play a key role in the development of atherosclerosis. Reactive oxygen species (ROS) released during inflammation additionally oxidize LDL, which is subsequently taken up in an unregulated way through scavenger receptors on macrophages to form foam cells, the hallmark of atherosclerotic lesions. Previous work has shown that the lipid ceramide, which is found in aggregated LDL and in atherosclerotic plaques, decreases intracellular peroxide most likely through reducing NADPH oxidase activity. Ceramide is an important component of membrane microdomains called lipid rafts which are important for membrane protein function. Endogenous ceramide enhances lipid raft f'ormation and alters theirs composition. NADPH oxidase membrane subunits cytochrome b558 (which includes gp91) strongly associates with lipid rafts Therefore present study investigated whether short chain ceramides reduce NADPH oxidase in U937 monocytes by disrurting the membrane component of NADPH oxidase. Results showed that C2 ceramide alters the distribution of raft marker, flottillin and the raft environment. NADPH oxidase membrane component gp9J phox and cytosolic component p47 phox were identified in rafts. C2 ceramide reduces both gp91 and p47 phox in rafts, which leads to the decrease of peroxide production by NADPH oxidase. Ceramide is also an important second messenger involved in many different signaling pathways associated with atherogenesis from the activation of sphingomyelinase (SMase). It has been reported that SMase enhances LDL receptor mediated LDL endocytosis. However, no study has been done to investigate the effect of ceramide on scavenger receptors such as CD36 and oxidized LDL (OxLDL) uptake. CD36 is the major recertor far OxLDL. Reduced CD36 expression results in less foam cell formation and less atherosclerotic lesion without disrupting the clearance of OxLDL from plasma. This thesis shows that ceramides significantly reduce CD36 surface expression on U937 monocytes, macrophages and human primary monocytes. This effect is seen using both synthetic short chain ceramide and SMase catalysed long chain ceramide treatment. To investigate whether the effect of ceramide on CD36 is functional, OxLOL uptake was measured in ceramide treated cells. Ceramide reduces the uptake of OxLOL by both U937 monocytes and PMA-differentiated macrophages. The mechanism of ceramide reduction of CD36 expression was studied by measuring the surface antigen using flow cytometry and fluorescence microscopy, whole cellular CD36 expression and shedding of C036 by Western blotting of cell lysates and cell culture supernatants and mRNA level of CD36 using RT-PCR. Ceramide reduces shedding of CD36, activates mRNA expression of CD36 and induces intracellular CD36 accumulation probably through retaining the receptor inside cells. In summary, ceramides modulate several of the processes involved in LOL oxidation and uptake by CD36 receptors on monocytes/macrophages in a way which may protect against atherosclerosis.

Dealing with cell death – an ageing problem?

The aged population have an increased susceptibility to infection, therefore function of the innate immune system may be impaired as we age. Macrophages, and their precursors monocytes, play an important role in host defence in the form of phagocytosis, and also link the innate and adaptive immune system via antigen presentation. Classically-activated ‘M1’ macrophages are pro-inflammatory, which can be induced by encountering pathogenic material or pro-inflammatory mediators. Alternatively activated ‘M2’ macrophages have a largely reparative role, including clearance of apoptotic bodies and debris from tissues. Despite some innate immune receptors being implicated in the clearance of apoptotic cells, the process has been observed to have a dominant anti-inflammatory phenotype with cytokines such as IL-10 and TGF-ß being implicated. The atherosclerotic plaque contains recruited monocytes and macrophages, and is a highly inflammatory environment despite high levels of apoptosis. At these sites, monocytes differentiate into macrophages and gorge on lipoproteins, resulting in formation of ‘foam cells’ which then undergo apoptosis, recruiting further monocytes. This project seeks to understand why, given high levels of apoptosis, the plaque is a pro-inflammatory environment. This phenomenon may be the result of the aged environment or an inability of foam cells to elicit an anti-inflammatory effect in response to dying cells. Here we demonstrate that lipoprotein treatment of macrophages in culture results in reduced capacity to clear apoptotic cells. The capability of lipoprotein treated macrophages to respond to inflammatory stimuli is also shown. Monocyte recruitment to the plaque is currently under study, as is apoptotic cell-mediated immune modulation of human monocyte-derived macrophages.

Mass transfer and chemical reaction on a distillation plate

A multistage distillation column in which mass transfer and a reversible chemical reaction occurred simultaneously, has been investigated to formulate a technique by which this process can be analysed or predicted. A transesterification reaction between ethyl alcohol and butyl acetate, catalysed by concentrated sulphuric acid, was selected for the investigation and all the components were analysed on a gas liquid chromatograph. The transesterification reaction kinetics have been studied in a batch reactor for catalyst concentrations of 0.1 - 1.0 weight percent and temperatures between 21.4 and 85.0 °C. The reaction was found to be second order and dependent on the catalyst concentration at a given temperature. The vapour liquid equilibrium data for six binary, four ternary and one quaternary systems are measured at atmospheric pressure using a modified Cathala dynamic equilibrium still. The systems with the exception of ethyl alcohol - butyl alcohol mixtures, were found to be non-ideal. Multicomponent vapour liquid equilibrium compositions were predicted by a computer programme which utilised the Van Laar constants obtained from the binary data sets. Good agreement was obtained between the predicted and experimental quaternary equilibrium vapour compositions. Continuous transesterification experiments were carried out in a six stage sieve plate distillation column. The column was 3" in internal diameter and of unit construction in glass. The plates were 8" apart and had a free area of 7.7%. Both the liquid and vapour streams were analysed. The component conversion was dependent on the boilup rate and the reflux ratio. Because of the presence of the reaction, the concentration of one of the lighter components increased below the feed plate. In the same region a highly developed foam was formed due to the presence of the catalyst. The experimental results were analysed by the solution of a series of simultaneous enthalpy and mass equations. Good agreement was obtained between the experimental and calculated results.

The role of apoptotic cell clearance in a high-lipid environment:links to ageing

Individuals within the aged population show an increased susceptibility to infection, implying a decline in immune function, a phenomenon known as immunosenescence. Paradoxically, an increase in autoimmune disease, such as rheumatoid arthritis, is also associated with ageing, therefore some aspects of the immune system appear to be inappropriately active in the elderly. The above evidence suggests inappropriate control of the immune system as we age. Macrophages, and their precursors monocytes, play a key role in control of the immune system. They play an important role in host defence in the form of phagocytosis, and also link the innate and adaptive immune system via antigen presentation. Macrophages also have a reparative role, as professional phagocytes of dead and dying cells. Clearance of apoptotic cells by macrophages has also been shown to directly influence immune responses in an anti-inflammatory manner. Inappropriate control of macrophage function with regards to dead cell clearance may contribute to pathology as we age. The aims of this study were to assess the impact of lipid treatment, as a model of the aged environment, on the ability of macrophages to interact with, and respond to, apoptotic cells. Using a series of in vitro cell models, responses of macrophages (normal and lipid-loaded) to apoptotic macrophages (normal and lipid-loaded) were investigated. Monocyte recruitment to apoptotic cells, a key process in resolving inflammation, was assessed in addition to cytokine responses. Data here shows, for the first time, that apoptotic macrophages (normal and lipid-loaded) induce inflammation in human monocyte-derived macrophages, a response that could drive inflammation in age-associated pathology e.g. atherosclerosis. Monoclonal antibody inhibition studies suggest the classical chemokine CX3CL1 may be involved in monocyte recruitment to apoptotic macrophages, but not apoptotic foam cells, therefore differential clearance strategies may be employed following lipid-loading. CD14, an important apoptotic cell tethering receptor, was not found to have a prominent role in this process, whilst the role for ICAM-3 remains unclear. Additionally, a small pilot study using macrophages from young (<25) and mid-life (>40) donors was undertaken. Preliminary data was gathered to assess the ability of primary human monocyte-derived macrophages, from young and mid-life donors, to interact with, and respond to, apoptotic cells. MØ from mid-life individuals showed no significant differences in their ability to respond to immune modulation by apoptotic cells compared to MØ from young donors. Larger cohorts would be required to investigate whether immune modulation of MØ by apoptotic cells contribute to inflammatory pathology throughout ageing.

Atmospheric plasma treatment of porous polymer constructs for tissue engineering applications

Porous 3D polymer scaffolds prepared by TIPS from PLGA (53:47) and PS are intrinsically hydrophobic which prohibits the wetting of such porous media by water. This limits the application of these materials for the fabrication of scaffolds as supports for cell adhesion/spreading. Here we demonstrate that the interior surfaces of polymer scaffolds can be effectively modified using atmospheric air plasma (AP). Polymer films (2D) were also modified as control. The surface properties of wet 2D and 3D scaffolds were characterised using zeta-potential and wettability measurements. These techniques were used as the primary screening methods to assess surface chemistry and the wettability of wet polymer constructs prior and after the surface treatment. The surfaces of the original polymers are rather hydrophobic as highlighted but contain acidic functional groups. Increased exposure to AP improved the water wetting of the treated surfaces because of the formation of a variety of oxygen and nitrogen containing functions. The morphology and pore structure was assessed using SEM and a liquid displacement test. The PLGA and PS foam samples have central regions which are open porous interconnected networks with maximum pore diameters of 49 μm for PLGA and 73 μm for PS foams. (Figure Presented) © 2007 Wiley-VCH Verlag GmbH & Co. KGaA.

Numerical heat transfer analysis of carbon-based foams for use in thermal protection system

The applicability of carbon-based foams as an insulating or active cooling material in thermal protection systems (TPSs) of space vehicles is considered using a computer modeling. This study focuses on numerical investigation of the performance of carbon foams for use in TPSs of space vehicles. Two kinds of carbon foams are considered in this study. For active cooling, the carbon foam that has a thermal conductivity of 100 W/m-k is used and for the insulation, the carbon foam having a thermal conductivity of 0.225 W/m-k is used. A 3D geometry is employed to simulate coolant flow and heat transfer through carbon foam model. Gambit has been used to model the 3D geometry and the numerical simulation is carried out in FLUENT. Numerical results from this thesis suggests that the use of CFOAM and HTC carbon foams in TPS's may effectively protect the aluminum structure of the space shuttle during reentry of the space vehicle.

Exploring the Use of Everglades Agricultural Area Canal Water as Base Medium for the Mass Production of Algae for Biofuels

Freshwater use is a major concern in the mass production of algae for biofuels. This project examined the use of canal water obtained from the Everglades Agricultural Area as a base medium for the mass production of algae. This water is not suitable for human consumption, and it is currently used for crop irrigation. A variety of canals were found to be suitable for water collection. Comparison of two methods for algal production showed no significant difference in biomass accumulation. It was discovered that synthetic reticulated foam can be used for algal biomass collection and harvest, and there is potential for its application in large-scale operations. Finally, it was determined that high alkaline conditions may help limit contaminants and competing organisms in growing algae cultures.

Caracterização mecânica, térmica e acústica de um compósito que utiliza rejeitos de mármore, granito e EPS para a fabricação de blocos para a construção civil

The use of composite materials for the construction industry has been the subject of numerous scientific papers in Brazil and in the world. One of the factors that motivate this quest is the housing deficit that countries especially the third world face. In Brazil this deficit reaches more than 6.5 million homes, around 12% of all US households . This paper presents a composite that was obtained from waste generated in processes for the production of granite and marble slabs, cement, gypsum, sand, crushed EPS and water. These wastes cause great damage to the environment and are thrown into landfi lls in bulk. The novelty of the work is in the combined study thermal, mechanical and acoustic composite obtained in real situation of rooms that are part of an experimental housing. Many blocks were made from cement compositions, plaster, foam, sand, marb le and / or granite, preliminary tests of mechanical and thermal resistance were made by choosing the most appropriate proportion. Will be given the manufacturing processes and assembly units 500 units 10 x 80 x 28 cm produced for the construction of an ex perimental home. We studied what kind of block and residue, marble or granite, made it more feasible for the intended purpose. The mechanical strength of the produced blocks were above 3.0 MPa. The thermal resistance of the blocks was confirmed by the maxi mum temperature difference between the inner and outer walls of rooms built around 8.0 ° C. The sound absorption for optimal room was around 31%. Demonstrated the feasibility of using the blocks manufactured with composite material proposed for construction.

Ecologia de comunidades e comportamento reprodutivo de anfíbios anuros em savana amazônica

The Amazon savannas occur as isolated patches throughout extensive areas of forest in the states of Amapá, Amazonas, Pará, and Roraima. There is a considerable variation in the composition of anuran assemblages in the localities and phytophysiognomies of Amazon savannas and given the absence of studies on reproductive behavior, a systematic and geographically wide sampling has been carried out in the Amapá savanna, located in the Eastern Amazon. The study was conducted in a savanna area in the state of Amapá to examine the composition, ecology, and reproductive behavior of anuran amphibians. We carried out 24 field trips in each phytophysiognomy (gramineous-woody savana, gramineous-herbaceous-woody savana, park savana, and arboreal savanna); for analysis of reproductive behavior observations were made during the period January to December 2013, lasting four consecutive days. Samples were collected by active and acoustic search along 20 plots of 100x50 meters. Twenty-one anuran species were recorded, of which four are new records for the state of Amapá: Dendropsophus walfordi, Scinax fuscomarginatus, Pseudopaludicola boliviana e Elachistocleis helianneae. The KruskalWallis ANOVA revealed significant differences between richness and species diversity in the phytophysiognomies (p < 0.05). The Bray-Curtis similarity coefficient divided the phytophysiognomies into three groups: arboreal savana, gramineous-woody savanna and gramineous-herbaceous-woody savanna, and park savanna. According to the non-metric multidimensional scaling, the structure of the anuran community resulted in a separation into three phytophysiognomies, with significant differences in the structure of communities (ANOSIM, R = 0.823; p < 0.001). In the study of community ecology, the results obtained for spatial, temporal, and trophic niche breadth suggest that the assemblage of anurans of the Amapá savanna is not composed of predominantly generalist species. Also, the presence of other specialist anurans may explain the processes of speciation associated with the isolation of habitats, resulting in heterogeneity and spatial discontinuity in the phytophysiognomies with open formations. The null model analysis revealed that the community is structured based on temporal and trophic niche, indicating a significant influence of contemporary ecological factors on the assemblage. The absence of structure based on spatial niche might be explained by the spatial segregation in the distribution and occupation of anurans in the different phytophysiognomies of the Amapá savanna. Regarding the reproductive behavior of anurans, 11 species were classified as having a long breeding season, intrinsically associated with the rainy season and the reproductive mode of most species that lay egg clutches in lentic water bodies. Six reproductive modes were recorded and parental care was observed in Leptodactylus macrosternum and L. podicipinus, whose reproductive mode is characterized by foam nests. Regarding behavioral reproductive strategies, calling males were observed in all species of anurans, satellite males were recorded only for D. walfordi, Hypsiboas multifasciatus, S. nebulosus and S. fuscomarginatus; active search for females was observed for Phyllomedusa hypochondrialis and L. fuscus, and male displacement was recorded only for Rhinella major and R. margaritifera. Of the reproductive behaviors observed, throat and vocal sac display is associated with courtship and territorial behavior exhibited by males. In addition to courtship behavior, visual signals associated with courtship strategies were recorded for the anurans of the Amapá savanna.

Fall prevention among older adults: a quantitative and qualitative study

The purpose of this study was to investigate the effect of a fall prevention program on older adults as well as to explore the perceptions of older adults have on fall risk and the fall prevention program. This research was completed in Newfoundland and Labrador, Canada with participants above the age of 65. The 10-week fall prevention program focused on balance, strength, and flexibility and was followed by focus groups with the control and intervention groups. Pre and post-test measures (postural sway, TUG test, foam and dome test, ABC Scale, ESE Scale, FES Scale, SAFFE) were completed to determine if the fall prevention program decreased fall risk. The results of the quantitative portion of the study did not produce significant results however the qualitative portion was very informative. Five themes emerged from the focus group data: risk factor awareness, confidence, connectedness, quality of life, and program promotion. This research highlights the importance of fall prevention programs for older adults, not only to keep them healthy, but also for the personal and social benefits they facilitate.

Proprietà di conduzione elettrica in campioni di grafene poroso

Il grafene, allotropo del carbonio costituito da un reticolo bidimensionale, è uno dei nanomateriali più promettenti allo stato attuale della ricerca nei campi della Fisica e della Chimica, ma anche dell'Ingegneria e della Biologia. Isolato e caratterizzato per la prima volta nel 2004 dai ricercatori russi Andre Geim e Konstantin Novoselov presso l'Università di Manchester, ha aperto la via sia a studi teorici per comprendere con gli strumenti della Meccanica Quantistica gli effetti di confinamento in due dimensioni (2D), sia ad un vastissimo panorama di ricerca applicativa che ha l'obiettivo di sfruttare al meglio le straordinarie proprietà meccaniche, elettriche, termiche ed ottiche mostrate da questo materiale. Nella preparazione di questa tesi ho personalmente seguito presso l'Istituto per la Microelettronica e i Microsistemi (IMM) del CNR di Bologna la sintesi mediante Deposizione Chimica da Fase Vapore (CVD) di grafene "tridimensionale" (3D) o "poroso" (denominato anche "schiuma di grafene", in inglese "graphene foam"), ossia depositato su una schiuma metallica dalla struttura non planare. In particolare l'obiettivo del lavoro è stato quello di misurare le proprietà di conduttività elettrica dei campioni sintetizzati e di confrontarle con i risultati dei modelli che le descrivono teoricamente per il grafene planare. Dopo un primo capitolo in cui descriverò la struttura cristallina, i livelli energetici e la conduzione dei portatori di carica nel reticolo ideale di grafene 2D (utilizzando la teoria delle bande e l'approssimazione "tight-binding"), illustrerò le differenti tecniche di sintesi, in particolare la CVD per la produzione di grafene poroso che ho seguito in laboratorio (cap.2). Infine, nel capitolo 3, presenterò la teoria di van der Pauw su cui è basato il procedimento per eseguire misure elettriche su film sottili, riporterò i risultati di conduttività delle schiume e farò alcuni confronti con le previsioni della teoria.

Advanced Aerogel Composites for Oil Remediation and Recovery

Oil spills in marine environments often damage marine and coastal life if not remediated rapidly and efficiently. In spite of the strict enforcement of environmental legislations (i.e., Oil Pollution Act 1990) following the Exxon Valdez oil spill (June 1989; the second biggest oil spill in U.S. history), the Macondo well blowout disaster (April 2010) released 18 times more oil. Strikingly, the response methods used to contain and capture spilled oil after both accidents were nearly identical, note that more than two decades separate Exxon Valdez (1989) and Macondo well (2010) accidents.

The goal of this dissertation was to investigate new advanced materials (mechanically strong aerogel composite blankets-Cabot® Thermal Wrap™ (TW) and Aspen Aerogels® Spaceloft® (SL)), and their applications for oil capture and recovery to overcome the current material limitations in oil spill response methods. First, uptake of different solvents and oils were studied to answer the following question: do these blanket aerogel composites have competitive oil uptake compared to state-of-the-art oil sorbents (i.e., polyurethane foam-PUF)? In addition to their competitive mechanical strength (766, 380, 92 kPa for Spaceloft, Thermal Wrap, and PUF, respectively), our results showed that aerogel composites have three critical advantages over PUF: rapid (3-5 min.) and high (more than two times of PUF’s uptake) oil uptake, reusability (over 10 cycles), and oil recoverability (up to 60%) via mechanical extraction. Chemical-specific sorption experiments showed that the dominant uptake mechanism of aerogels is adsorption to the internal surface, with some contribution of absorption into the pore space.

Second, we investigated the potential environmental impacts (energy and chemical burdens) associated with manufacturing, use, and disposal of SL aerogel and PUF to remove the oil (i.e., 1 m3 oil) from a location (i.e., Macondo well). Different use (single and multiple use) and end of life (landfill, incinerator, and waste-to-energy) scenarios were assessed, and our results demonstrated that multiple use, and waste-to-energy choices minimize the energy and material use of SL aerogel. Nevertheless, using SL once and disposing via landfill still offers environmental and cost savings benefits relative to PUF, and so these benefits are preserved irrespective of the oil-spill-response operator choices.

To inform future aerogel manufacture, we investigated the different laboratory-scale aerogel fabrication technologies (rapid supercritical extraction (RSCE), CO2 supercritical extraction (CSCE), alcohol supercritical extraction (ASCE)). Our results from anticipatory LCA for laboratory-scaled aerogel fabrication demonstrated that RSCE method offers lower cumulative energy and ecotoxicity impacts compared to conventional aerogel fabrication methods (CSCE and ASCE).

The final objective of this study was to investigate different surface coating techniques to enhance oil recovery by modifying the existing aerogel surface chemistries to develop chemically responsive materials (switchable hydrophobicity in response to a CO2 stimulus). Our results showed that studied surface coating methods (drop casting, dip coating, and physical vapor deposition) were partially successful to modify surface with CO2 switchable chemical (tributylpentanamidine), likely because of the heterogeneous fiber structure of the aerogel blankets. A possible solution to these non-uniform coatings would be to include switchable chemical as a precursor during the gel preparation to chemically attach the switchable chemical to the pores of the aerogel.

Taken as a whole, the implications of this work are that mechanical deployment and recovery of aerogel composite blankets is a viable oil spill response strategy that can be deployed today. This will ultimately enable better oil uptake without the uptake of water, potential reuse of the collected oil, reduced material and energy burdens compared to competitive sorbents (e.g., PUF), and reduced occupational exposure to oiled sorbents. In addition, sorbent blankets and booms could be deployed in coastal and open-ocean settings, respectively, which was previously impossible.

Utilisation d’un modèle de co-culture cellulaire pour l’évaluation in vitro du transport inverse du cholestérol

De nouveaux modèles cellulaires in vitro par transfert de milieu et par coculture ont été mis au point afin d’évaluer la capacité des HDL à éliminer l’excès de cholestérol des tissus périphériques et de le transporter vers le foie afin d’être excrété par le foie, un processus nommé le transport inverse du cholestérol (TIC). Le système cellulaire par transfert in vitro où des macrophages J774 sont gorgés de LDL acétylées et marqués au 3H-cholestérol a été préalablement établi afin de mesurer par scintillation l’efflux de cholestérol marqué vers le milieu de culture contenant des accepteurs de cholestérol. Ce milieu conditionné est transféré sur des cellules HepG2 afin d’étudier l’influx du cholestérol marqué. Ce dernier nous permet d’observer un transport de cholestérol de 25 % hors des J774 et un transport de 39 000 cpm dans les HepG2 en utilisant un milieu contenant 2 % de sérums humains mis en commun. Une stimulation des cellules J774 par l’AMPc augmente l’efflux et l’influx d’environ 45 %. Des tests de preuve de concept ont été effectués sur le système cellulaire par co-culture qui utilise des chambres de Boyden où les J774 sont localisées au fond d’un puits et les HepG2 dans un insert, et où le milieu est partagé entre les deux types cellulaires. On a déterminé qu’une confluence densité de 60 000 cellules/cm2 sur un insert constitué d’une membrane de polyester avec des pores de 3,0 μm, sans autre revêtement, permet d’observer un influx spécifique au sérum d’environ 6 000 cpm associés aux cellules HepG2, où 50 % des comptes radioactifs sont dans les cellules et l’autre moitié présente à la surface cellulaire.