Enhanced Plasticity of Zr-Based Bulk Metallic Glass Matrix Composite with Ductile Reinforcement

A composite material containing uniformly distributed micrometer-sized Nb particles in a Zr-based amorphous matrix was prepared by suction cast. The resulting material exhibits high fractured strength over 1550 MPa and enhanced plastic strain of about 29.7% before failure in uniaxial compression test at room temperature. Studies of the serrations on the stress-strain curves and the shear bands on the fractured samples reveal that the amplitude of the stress drop of each serration step corresponds to the extent of the propagation of a single shear band through the materials. The composite exhibits more serration steps and smaller amplitude of stress drop due to the pinning of shear band propagation by ductile Nb particles.

Direct numerical test of the B-G-K model equation by the DSMC method

In the present paper the rarefied gas how caused by the sudden change of the wall temperature and the Rayleigh problem are simulated by the DSMC method which has been validated by experiments both in global flour field and velocity distribution function level. The comparison of the simulated results with the accurate numerical solutions of the B-G-K model equation shows that near equilibrium the BG-K equation with corrected collision frequency can give accurate result but as farther away from equilibrium the B-G-K equation is not accurate. This is for the first time that the error caused by the B-G-K model equation has been revealed.

Size Effect and Geometrical Effect of Polycrystals and Thin Film/Substrate System in Micro-indentation Test

Micro-indentation test at scales on the order of sub-micron has shown that the measured hardness increases strongly with decreasing indent depth or indent size, which is frequently referred to as the size effect. Simultaneously, at micron or sub-micron scale, the material microstructure size also has an important influence on the measured hardness. This kind of effect, such as the crystal grain size effect, thin film thickness effect, etc., is called the geometrical effect by here. In the present research, in order to investigate the size effect and the geometrical effect, the micro-indentation experiments are carried out respectively for single crystal copper and aluminum, for polycrystal aluminum, as well as for a thin film/substrate system, Ti/Si3N4. The size effect and geometrical effect are displayed experimentally. Moreover, using strain gradient plasticity theory, the size effect and the geometrical effect are simulated. Through comparing experimental results with simulation results, length-scale parameter appearing in the strain gradient theory for different cases is predicted. Furthermore, the size effect and the geometrical effect are interpreted using the geometrically necessary dislocation concept and the discrete dislocation theory. Member Price: $0; Non-Member Price: $25.00

Surface Tension and Its Temperature Coefficient of Molten Tin Determined with the Sessile Drop Method at Different Oxygen Partial Pressures

The surface tension of molten tin has been determined by the sessile drop method at The surface tension of molten tin has been determined by the sessile drop method at temperatures ranging from 523 to 1033 K and in the oxygen partial pressure (P-O2) range from 2.85 x 10(-19) to 8.56 x 10(-6) MPa, and its dependence on temperature and oxygen partial pressure has been analyzed. At P-O2 = 2.85 x 10(-19) and 1.06 x 10(-15) MPa, the surface tension decreases linearly with the increase of temperature and its temperature coefficients are -0.151 and -0.094 mNm(-1) K-1, respectively. However, at high P-O2 (3.17 x 10(-10), 8.56 x 10(-6) MPa), the surface tension increases with the temperature near the melting point (505 K) and decreases above 723 K. The surface tension decrease with increasing P-O2 is much larger near the melting point than at temperatures above 823 K. The contact angle between the molten tin and the alumina substrate is 158-173degrees, and the wettability is poor.

Theory and Application of the Transient Injection Well Test

Based on the theory of the pumping well test, the transient injection well test was suggested in this paper. The design method and the scope of application are discussed in detail. The mathematical models are developed for the short-time and long-time transient injection test respectively. A double logarithm type curve matching method was introduced for analyzing the field transient injection test data. A set of methods for the transient injection test design, experiment performance and data analysis were established. Some field tests were analyzed, and the results show that the test model and method are suitable for the transient injection test and can be used to deal with the real engineering problems.

Diagnóstico comparativo de mastitis en leche bovina, por tres pruebas de campo: california mastitis test (CMT), acidez (NaOH), y reductasa, en los municipios de la Concordia, San Rafael del Norte y San Sebastián de Yali, Jinotega

Con el propósito de evaluar tres técnicas para la determinación de Mastitis, (California Mastitis Test (CMT), Hidróxido de Sodio (NaHO) y Azul de Metíleno (AM)), en vacas de doble propósito, en 2000 se efectuó un estudio en los municipios de La Concordia, San Rafael de Norte y San Sebastián de Yalí, del Departamento de Jinotega. Se utilizaron Fincas de Referencia atendidas por el entonces Ministerio de Agricultura y Ganadería (MAG), de las cuales se seleccionaron catorce (14) fincas privadas y dos Cooperativas, para un total de 16 fincas que representaron el 53.3 % del total de fincas. De éstas se muestrearon 398 vacas en producción de diversas razas (Pardo suizo, Brahman y cruces entre Pardo suizo, Criollo y Holstein con Cebú y otros) de diversas lactaciones (número parto}. Las muestras de cada cuarto de la vaca, se tomaron a la hora del ordeño, entre 5:00 y 7:00a.m. Los resultados de CMT e NaHO, (+ ó -), se anotaron en campo al momento de prueba. En la prueba de AM, se hicieron 4 lecturas: 1) al momento de prueba, 2) a los 15 minutos, 3) a una hora y, 4) a tres horas después de la prueba. Se obtuvo un total de 396 datos de 4 cuartos en cada técnica, para un total de 4,752 observaciones. La información se analizó mediante una prueba de Chí Cuadrado, con el Procedimiento CATMOD, del Statistical Análisis System (SAS), Versión para PC 6.03, NC. Las variables de clasificación en el análisis fueron Razas (1-3), Números de Parto (1-6) y Meses de lactación (1-9). De las técnicas, se obtuvo el 46.2, 4.6 y 15.3 % de pruebas positivas con CMT, NaOH y AM, respectivamente; la CMT resultó más efectiva en la determinación de mastitis. De las Razas estudiadas, el Brahmán presentó un 45.2% de afectación por mastitis, mayor que Pardo suizo y cruces indefinidos, con 30.6 y 24.2 %, respectivamente. A partir del tercer parto, se incrementa el nivel de infestación de esta enfermedad, y durante la lactación, en los meses 4, 5,8 y 9.

Unsteady Model of Drop Marangoni Migration in Microgravity

The experiments of drop Marangoni migration have been performed by the drop shift facility of short period of 4.5 s, and the drop accelerates gradually to an asymptotic velocity during the free fall. The unsteady and axisymmetric model is developed to study the drop migration for the case of moderate Reynolds number Re = O(1), and the results are compared with the experimental ones in the present paper. Both numerical and experimental results show that the migration velocity for moderate Reynolds number is several times smaller than that given by the linear YGB theory.

Rayleigh-Taylor Instability of a Liquid Drop at High Bond Numbers

给出了高Bond数下黏性液滴表面Rayleigh-Taylor线性不稳定性的分析解,这种不稳定性对于超音速气流作用下液滴破碎的早期阶段起着至关重要的作用.基于稳定性分析的结果,导出了用于估算稳定液滴的最大直径及液滴无量纲初始破碎时间的计算式,这些计算式与相关文献给出的实验和分析结果比较显示了良好的一致.

Nonuniformity Effect of Surface-Nanocrystalline Materials in Nanoindentation Test

In the present research, microstructures of the surface-nanocrystalline Al alloy material are observed and measured based on the transmission electron microscopy (TEM) technique, and the corresponding mechanical behaviors are investigated experimentally and theoretically. In the experimental research, the nanoindentation test method is used, and the load and microhardness curves are measured, which strongly depend on the grain size and grain size nonuniformity. Two kinds of the nanoindentation test methods are adopted: the randomly selected loading point method and the continuous stiffness method. In the theoretical modeling, based on the microstructure characteristics of the surface-nanocrystalline Al alloy material, a dislocation pile-up model considering the grain size effect and based on the Mott theory is presented and used. The hardness-indent depth curves are predicted and modeled.

A diagnostic system for the microgravity experiments on Marangoni drop migrations

An optical diagnostic system designed for the microgravity experiments on Marangoni drop migrations has been depicted in the presented paper. One part of the optical system was used to image and record the drops tracks; the other part was an equal-thick interferential system, it has the ability to observe the fine structures of the drop migrations. Some ground-based experiments had been performed and the results were simply discussed in the present paper.

Space experimental device on Marangoni drop migrations of large Reynolds numbers

The space experimental device for testing the Marangoni drop migrations has been discussed in the present paper. The experiment is one of the spaceship projects of China. In comparison with similar devices, it has the ability of completing all the scientific experiments by both auto controlling and telescience methods. It not only can perform drop migration experiments of large Reynolds numbers but also has an equi-thick interferential system.