Radio frequency studies of surface resistance and critical magnetic field of type I and type II superconductors

The surface resistance and the critical magnetic field of lead electroplated on copper were studied at 205 MHz in a half-wave coaxial resonator. The observed surface resistance at a low field level below 4.2°K could be well described by the BCS surface resistance with the addition of a temperature independent residual resistance. The available experimental data suggest that the major fraction of the residual resistance in the present experiment was due to the presence of an oxide layer on the surface. At higher magnetic field levels the surface resistance was found to be enhanced due to surface imperfections.

The attainable rf critical magnetic field between 2.2°K and T_c of lead was found to be limited not by the thermodynamic critical field but rather by the superheating field predicted by the one-dimensional Ginzburg-Landau theory. The observed rf critical field was very close to the expected superheating field, particularly in the higher reduced temperature range, but showed somewhat stronger temperature dependence than the expected superheating field in the lower reduced temperature range.

The rf critical magnetic field was also studied at 90 MHz for pure tin and indium, and for a series of SnIn and InBi alloys spanning both type I and type II superconductivity. The samples were spherical with typical diameters of 1-2 mm and a helical resonator was used to generate the rf magnetic field in the measurement. The results of pure samples of tin and indium showed that a vortex-like nucleation of the normal phase was responsible for the superconducting-to-normal phase transition in the rf field at temperatures up to about 0.98-0.99 T_c' where the ideal superheating limit was being reached. The results of the alloy samples showed that the attainable rf critical fields near T_c were well described by the superheating field predicted by the one-dimensional GL theory in both the type I and type II regimes. The measurement was also made at 300 MHz resulting in no significant change in the rf critical field. Thus it was inferred that the nucleation time of the normal phase, once the critical field was reached, was small compared with the rf period in this frequency range.

Avaliação da sorção de Cu (II) e Hg (II) pela Sargassum sp modificado com epicloridrina

É crescente o aumento da preocupação do homem com a contaminação de ambientes aquáticos uma vez que da subsistência dos mesmos depende o bem estar de todos. Ao mesmo tempo em que cresce a preocupação tem aumentado a quantidade de pesquisas em busca de tecnologias alternativas ao tratamento e remediação de efluentes aquosos contaminados pelas mais diversas substâncias incluindo os metais pesados. Nas últimas décadas, tem crescido o número de trabalhos avaliando a capacidade de sorção e a viabilidade da utilização de biossorventes de baixo custo na captação de íons metálicos e um desses materiais são as biomassas de algas pardas. Dentre os vários gêneros existentes no planeta o território brasileiro é rico na macroalga do gênero Sargassum. Muito embora a composição dessas biomassas varie o principal constituinte das mesmas é o ácido algínico e seus sais alcalinos na forma de um copolímero linear, homopolimérico, com unidades do ácido manurônico, (M), (1-4)-β-D- ligado e seu epímero em C-5 nos resíduos α-L-gulurônicos, (G), respectivamente, covalentemente ligados entre si em sequencias diferenciadas ou em blocos. Os monômeros podem aparecer em blocos homopoliméricos consecutivos, resíduos G (unidades G), resíduos consecutivos M (unidades M), pequenas unidades alternadas M e G (blocos MG), ou em blocos aleatoriamente organizados. A proposta dessa dissertação é realizar a modificação do copolímero existente na biomassa com epicloridrina, avaliar e comparar a captação de íons Cu (II) e Hg (II) pela biomassa da alga Sargassum sp., com a biomassa não modificada e resultados publicados na literatura

Design, Synthesis, and Study of Novel Platforms for Iron-N2 Chemistry and Photoinduced, Copper-mediated C-N Bond Formation

Several new ligand platforms designed to support iron dinitrogen chemistry have been developed. First, we report Fe complexes of a tris(phosphino)alkyl (CP^iPr₃) ligand featuring an axial carbon donor intended to conceptually model the interstitial carbide atom of the nitrogenase iron-molybdenum cofactor (FeMoco). It is established that in this scaffold, the iron center binds dinitrogen trans to the C_alkyl anchor in three structurally characterized oxidation states. Fe-C_alkyl lengthening is observed upon reduction, reflective of significant ionic character in the Fe-C_alkyl interaction. The anionic (CP^iPr₃)FeN₂^- species can be functionalized by a silyl electrophile to generate (CP^iPr₃)Fe-N₂SiR₃. This species also functions as a modest catalyst for the reduction of N₂ to NH₃. Next, we introduce a new binucleating ligand scaffold that supports an Fe(μ-SAr)Fe diiron subunit that coordinates dinitrogen (N₂-Fe(μ-SAr)Fe-N₂) across at least three oxidation states (Fe^IIFe^II, Fe^IIFe^I, and Fe^IFe^I). Despite the sulfur-rich coordination environment of iron in FeMoco, synthetic examples of transition metal model complexes that bind N₂ and also feature sulfur donor ligands remain scarce; these complexes thus represent an unusual series of low-valent diiron complexes featuring thiolate and dinitrogen ligands. The (N₂-Fe(μ-SAr)Fe-N₂) system undergoes reduction of the bound N₂ to produce NH₃ (~50% yield) and can efficiently catalyze the disproportionation of N₂H₄ to NH₃ and N₂. The present scaffold also supports dinitrogen binding concomitant with hydride as a co-ligand. Next, inspired by the importance of secondary-sphere interactions in many metalloenzymes, we present complexes of iron in two new ligand scaffolds ([SiP^NMe₃] and [SiP^iPr₂P^NMe]) that incorporate hydrogen-bond acceptors (tertiary amines) which engage in interactions with nitrogenous substrates bound to the iron center (NH₃ and N₂H₄). Cation binding is also facilitated in anionic Fe(0)-N₂ complexes. While Fe-N₂ complexes of a related ligand ([SiP^iPr₃]) lacking hydrogen-bond acceptors produce a substantial amount of ammonia when treated with acid and reductant, the presence of the pendant amines instead facilitates the formation of metal hydride species.

Additionally, we present the development and mechanistic study of copper-mediated and copper-catalyzed photoinduced C-N bond forming reactions. Irradiation of a copper-amido complex, ((m-tol)₃P)₂Cu(carbazolide), in the presence of aryl halides furnishes N-phenylcarbazole under mild conditions. The mechanism likely proceeds via single-electron transfer from an excited state of the copper complex to the aryl halide, generating an aryl radical. An array of experimental data are consistent with a radical intermediate, including a cyclization/stereochemical investigation and a reactivity study, providing the first substantial experimental support for the viability of a radical pathway for Ullmann C-N bond formation. The copper complex can also be used as a precatalyst for Ullmann C-N couplings. We also disclose further study of catalytic C_alkyl-N couplings using a CuI precatalyst, and discuss the likely role of [Cu(carbazolide)₂]^- and [Cu(carbazolide)₃]^- species as intermediates in these reactions.

Finally, we report a series of four-coordinate, pseudotetrahedral P₃Fe^II-X complexes supported by tris(phosphine)borate ([PhBP₃Fe^R]^-) and phosphiniminato X-type ligands (-N=PR'₃) that in combination tune the spin-crossover behavior of the system. Low-coordinate transition metal complexes such as these that undergo reversible spin-crossover remain rare, and the spin equilibria of these systems have been studied in detail by a suite of spectroscopic techniques.

Biossorção de cobre (II) e cálcio (II) pela biomassa da macroalga marrom Sargassum filipendula

No presente trabalho, pretendeu-se avaliar a alga marinha Sargassum filipendula na sua capacidade de remoção do metal cobre na presença do metal cálcio, de modo a verificar o efeito da presença do cálcio, proveniente do hidróxido de cálcio (cal hidratada), utilizado no tratamento primário de efluentes por precipitação química. Para tanto, foi realizado primeiramente o estudo da cinética de biossorção de cobre e cálcio em regime de batelada, nas concentrações de 50 e 200 g/mL, e em seguida foi estudado o equilíbrio da biossorção de cobre e cálcio, também em regime de batelada, utilizando soluções isoladas e combinadas de cobre e cálcio, em concentrações variadas, com biomassa lavada com água corrente e com HCl 0,1 mol/L, de modo a verificar se houve melhora na biossorção com a protonação da biomassa. Os resultados do estudo cinético da biossorção do cobre e do cálcio mostraram, em todos os casos, que o equilíbrio ocorreu até os 30 minutos iniciais e que os resultados do cobre se ajustaram melhor a um modelo cinético de segunda ordem, enquanto que os resultados do cálcio não se ajustaram a nenhum dos dois modelos propostos. Foi possível verificar ainda uma relação direta entre biossorção de cobre e liberação de elementos alcalinos e alcalino-terrosos, sugerindo o envolvimento de troca-iônica durante o processo. Já com os resultados de estudo do equilíbrio da biossorção dos metais cobre e cálcio, foi possível obter algumas conclusões, dentre as quais podemos destacar a predileção pelo modelo de isotermas de Langmuir e a interferência na biosorção do cobre causada pela presença do cálcio na solução. Nesta etapa, foi possível ainda estabelecer novamente a correlação de permuta entre os metais cobre e alcalinos/alcalino terrosos. Os modelos de pseudo-primeira ordem e segunda ordem foram utilizados para avaliar a cinética de adsorção dos íons metálicos pela biomassa, enquanto que os modelos das isotermas de Langmuir e de Freundlich, foram utilizados para a representação do equilíbrio da biossorção

Preparação e avaliação de hidrogéis nanocompósitos à base de alginato na remoção de Cu (II) e Zn (II) de soluções aquosas

Esta dissertação teve como objetivo, a preparação de hidrogéis à base de alginato contendo argila e material magnético em sua estrutura. Foram analisadas as modificações nas características físico-químicas dos hidrogéis preparados com diferentes reticulantes (CaCl2 e FeCl3) e diferentes concentrações de material magnético (1 e 3 % m/m) e argila (1, 5 e 10 %). Após isso, os hidrogéis foram avaliados quanto à capacidade de remoção de íons Cu2+ e Zn2+ de soluções aquosas. As amostras foram caracterizadas quanto à composição química por espectroscopia na região do infravermelho (FTIR), quanto à morfologia por microscopia óptica e microscopia eletrônica de varredura (SEM) e quanto às propriedades magnéticas por magnetometria de amostra vibrante (VSM). Através da técnica de difratometria de raios-X (XRD), foi possível verificar a natureza do material magnético e a dispersão da argila nos hidrogéis. A estabilidade térmica das amostras foi analisada por análise termogravimétrica (TGA). Os resultados mostraram que tanto a argila como o material magnético ficaram bem dispersos nas amostras. De forma geral, foram preparados hidrogéis com morfologia esférica, sendo que os hidrogéis de alginato de cálcio tenderam a apresentar maior resistência térmica do que os hidrogéis de alginato de ferro. Todas as amostras magnéticas apresentaram comportamento superparamagnético, porém as amostras de alginato de ferro mostraram-se quebradiças após o intumescimento em água. O tempo médio de equilíbrio de intumescimento foi de 240 minutos. Os resultados de cinética de adsorção mostraram que os hidrogéis de alginato de cálcio preparados nas condições avaliadas nesta Dissertação foram eficientes na remoção dos íons Cu2+ e Zn2+, sendo que o cobre apresentou maior afinidade pelo hidrogel do que o zinco

Pool boiling heat transfer of ultra-light copper foam with open cells

High speed visualizations and thermal performance studies of pool boiling heat transfer on copper foam covers were performed at atmospheric pressure, with the heating surface area of 12.0 mm by 12.0 mm, using acetone as the working fluid. The foam covers have ppi (pores per inch) from 30 to 90, cover thickness from 2.0 to 5.0 mm, and porosity of 0.88 and 0.95. The surface superheats are from -20 to 190 K, and the heat fluxes reach 140 W/cm(2). The 30 and 60 ppi foam covers show the periodic single bubble generation and departure pattern at low surface superheats. With continuous increases in surface superheats, they show the periodic bubble coalescence and/or re-coalescence pattern. Cage bubbles were observed to be those with liquid filled inside and vented to the pool liquid. For the 90 ppi foam covers, the bubble coalescence takes place at low surface superheats. At moderate or large surface superheats, vapor fragments continuously escape to the pool liquid. Boiling curves of copper foams show three distinct regions. Region I and II are those of natural convection heat transfer, and nucleate boiling heat transfer for all the foam covers. Region III is that of either a resistance to vapor release for the 30 and 60 ppi foam covers, or a capillary-assist liquid flow towards foam cells for the 90 ppi foam covers. The value of ppi has an important effect on the thermal performance. Boiling curves are crossed between the high and low ppi foam covers. Low ppi foams have better thermal performance at low surface superheats, but high ppi foams have better one at moderate or large surface superheats and extend the operation range of surface superheats. The effects of other factors such as pool liquid temperature, foam cover thickness on the thermal performance are also discussed.

Silver nanocluster-based fluorescent sensors for sensitive detection of Cu(II)

In this work, we report the first application of water-soluble fluorescent Ag nanoclusters in fluorescent sensors. The fluorescence of poly(methacrylic acid) (PMAA)-templated Ag nanoclusters was found to be quenched effectively by Cu2+, but not when other common metal ions were present. By virtue of the specific response toward the analyte, a new, simple, and sensitive fluorescent method for detecting Cu2+ has been developed based on Ag nanoclusters.

Selective oxidation of cyclohexane with hydrogen peroxide in the presence of copper pyrophosphate

Liquid phase oxidation of cyclohexane was carried out under mild reaction condition over copper pyrophosphate catalyst in CH3CN using hydrogen peroxide as an oxidant at the temperature between 25 and 80 degrees C. The copper pyrophosphate catalyst was characterized by means of XRD, FT-IR and water contact angle measurement. It was found that appropriate surface hydrophobicity is the key factor for the excellent performance of the catalyst. In addition, a significant improvement for the cyclohexane conversion in the presence of organic acid was observed.

Self-Assembly from Two-Dimensional Layered Networks to Tetranuclear Structures: Syntheses, Structures, and Properties of Four Copper-Thiacalix[4]arene Compounds

Two new copper-thiacalix[4]arene compounds, [Cu-2(1)-Cl-2(H(4)TC4A)](CH3OH) (1) and [Cu(I)2Cl(2)(H(4)PTC4A)](CH3OH)(CHCl3)(0.5) (2) (where H(4)TC4A = p-tert-butylthiacalix[4]arene and H(4)PTC4A = p-phenylthiacalix[4]arene), were synthesized by the solvothermal method in the mixed CH3OH/CHCl3 (1: 1) solvent and reassembled in air at room temperature to two other structures, [(Cu4Cl3)-Cl-II(HCO2)(TC4A)(CH3-OH)(2)(H2O)](CHCl3)(CH3OH)(2.7) (3) and [(Cu4Cl4)-Cl-II(PTC4A)(CH3OH)(4)] (4), respectively. All these four compounds were characterized by TG analyses, FTIR spectroscopy, and singlecrystal X-ray diffraction analyses. Compounds 1 and 2 feature two-dimensional layered networks, while compounds 3 and 4 are assembled by some tetranuclear units.

Theoretical studies on the reaction mechanism of oxidation of primary alcohols by Zn/Cu(II)-phenoxyl radical catalyst

The catalytic mechanism for the oxidation of primary alcohols catalyzed by the two functional models of galactose oxidase (GOase), M-II L (M = Cu, Zn; L = N,N'-bis(3,5-di-tert-butyl-2-hydroxyphenyl)1-2-diiminoquinone)), has been studied by use of the density functional method B3LYP The catalytic cycle of Cu- and Zn-catalysts consists of two parts, namely, substrate oxidation (primary alcohol oxidation) and O-2 reduction (catalyst regeneration). The catalytic mechanisms have been studied for the two reaction pathways (route 1 and route 2). The calculations indicate that the hydrogen atom transfer within the substrate oxidation part is the rate-determining step for both catalysts, in agreement with the experimental observation.

Charge carrier transporting, photoluminescent, and electroluminescent properties of zinc(II)-2-(2-hydroxyphenyl)benzothiazolate complex

Zinc(II)-2-(2-hydroxyphenyl)benzothiazolate complex is an excellent white-light-emitting material. Despite some studies devoted to this complex, no information on the real origin of the unusually broad electroluminescent (EL) emission is available. Therefore, we investigate photoluminescent and EL properties of the zinc complex. Orange phosphorescent emission at 580 nm was observed for the complex in thin film at 77 K, whereas only fluorescent emission was obtained at room temperature. Molecular orbitals, excitation energy, and emission energy of the complex were investigated using quantum chemical calculations. We fabricated the device with a structure of ITO/F16CuPc(5.5 nm)/Zn-complex/Al, where F16CuPc is hexadecafluoro copper phthalocyanine. The EL spectra varied strongly with the thickness of the emissive layer. We observed a significant change in the emission spectra with the viewing angles. Optical interference effects and light emission originating both from fluorescence and from phosphorescence can explain all of the observed phenomena, resulting in the broad light emission for the devices based on the Zn complex. We calculated the charge transfer integral and the reorganization energy to explain why the Zn complex is a better electron transporter than a hole transporter.

Extraction and separation of cadmium(II), iron(III), zinc(II), and europium(III) by Cyanex302 solutions using hollow fiber membrane modules

The mass transfer behaviors of Cd(II), Fe(III), Zn(II), and Eu(III) in sulfuric acid solution using microporous hollow fiber membrane (HFM) containing bis(2,4,4-trimethylpentyl)monothiophosphinic acid (commercial name Cyanex302) were investigated in this paper. The experimental results showed that the values of the mass transfer coefficients (K-w) decreased with an increase of H+ concentration and increased with an increase of extractant Cyanex302 concentration. The mass transfer resistance of Eu3+ was the largest because K-w value of Eu3+ was the smallest. The order of mass transfer rate of metal ions at low pH was Cd > Zn > Fe > Eu. Mixtures of Zn2+ and Eu3+ or of Zn2+ and Cd2+ were well separated in a counter-current circulation experiment using two modules connected in series at different initial acidity and concentration ratio. These results indicate that a hollow fiber membrane extractor is capable of separating the mixture compounds by controlling the acidity of the aqueous solution and by exploiting different mass transfer kinetics. The interfacial activity of Cyanex302 in sulfuric acid solution was measured and interfacial parameters were obtained according to Gibbs adsorption equation.

Synthesis, 2D NMR, electrochemistry and luminescence of ruthenium(II) complexes with 2,2 '-bipyridine and 5-(omega-bromoalkylamido)-1,10-phenanthroline

The efficient synthesis of 5-(5-bromovaleramido)-1,10-phenanthroline, 5-(6-bromohexanamido)-1,10-phenanthroline, and 5-(11-bromoundecanamido)-1,10-phenanthroline are described, which reacted with cis-Ru(bpy)(2)Cl-2. 2H(2)O and sodium hexafluorophosphate to form Ru(bpy)(2)[phen-NHCO(CH2)(n)Br](PF6)(2) (n = 4, 5 or 10; phen = 1,10-phenanthroline). The intricate H-1 NMR spectra at low field of these complexes were completely assigned in virtue of H-1-H-1 COSY technique. Cyclic voltammetry was used to study electrochemical behaviours of these complexes, and their luminescent properties were investigated with fluorescent spectra.

COMPARATIVE-STUDIES ON PERIODATOCUPRATE(II, III) AND TELLURATOCUPRATE(II, III)

The crystal structures, electronic spectra, and Cu2p XPS of Cu(III) complexes Na4H[Cu(H2TeO6)(2)]. 17H(2)O and Na4K[Cu(HlO(6))(2)]. 12H(2)O have been described. The characterizations of a Cu(III) atom in a complex are as follows: (i) In a square-planar coordination, the average bond length of Cu-O is 0.183 nm, shorter than the 0.190-0.200 nm found for a Cu(II) complex. (2) The ''blue shift'' occurs for d-d transitions in the electronic spectrum of the Cu(III) complex compared to those of its related Cu(II) complex, resulting from the higher valence state. (3) Cu(III) compounds with CuO4 square-planar coordination are expected to be diamagnetic whereas Cu(II) compounds to be paramagnetic. (4) Comprehensive investigations on Cu2p XPS show that the binding energy of Cu2p(3/2) of a pure Cu(III) compound is about 2.0 eV higher than that of its corresponding Cu(II) compound: the shake-up satellites do not appear in the Cu2p XPS for a pure diamagnetic Cu(III) compound, the same as found for a diamagnetic Ni(II) compound: the FWHM of the signal of Cu2p XPS may become broader for Cu(III) compound because its core hole's lifetime shortens due to the higher valence state of copper. (C) 1995 Academic Press, Inc.