Morphological characteristics of the Pterodoras granulosus digestive tube (Valenciennes, 1821) (Osteichthyes, Doradidae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Tomographic follow-up of bone regeneration after bone block harvesting from the mandibular ramus

Autogenous bone is still considered the gold standard, and the applicability of autogenous bone grafts is well established. However, the possibility of second harvesting from the same donor region remains unclear. The aim of this study was to perform a prospective evaluation of hard tissue deposition in the mandibular ramus after bone block harvesting using cone beam computed tomography (CBCT). Twenty-two patients with indications for augmentation procedures using autogenous bone from the mandibular ramus were selected. Three CBCT scans were performed with a tomographic guide before bone harvesting (T1) and at 14 days (T2) and 6 months (T3) after the surgical procedures. Measurements were obtained in 2D (area, mm(2)) and 3D (volume, mm(3)), and were subsequently compared. In the 2D analysis, the mean bone formation rate was 56%, while for the 3D analysis the mean rate was 9.7%. Despite this difference, there was a significant correlation between area and volume measurements. Our findings demonstrated the presence of hard tissue in the mandibular ramus at 6 months after bone harvesting, which suggests that it would be possible to reuse the same region for a second block harvesting. However, the second bone harvesting would involve less bone for transplantation when compared to the first bone harvesting.

Rehabilitation of the Maxillary Arch After Bone Graft Using Immediate Loading With Implant-Supported Fixed Restoration

Moderate and controlled loading environments support or enhance osteogenesis, and, consequently, a high degree of bone-to-implant contact can be acquired. This is because when osteoprogenitor cells are exposed to limited physical deformation, their differentiation into osteoblasts is enhanced. Then, some range of microstrain is considered advantageous for bone ingrowth and osseointegration. The primary stability has been considered one of the main clinical means of controlling micromotion between the implant and the forming interfacial tissue, which helps to establish the proper mechanical environment for osteogenesis. Based on the biological aspects of immediate loading (IL), the objective of this study is to present a clinical case of maxillary arch rehabilitation using immediate loading with implant-supported fixed restoration after bone graft. Ten dental implants were placed in the maxilla 6 months after the autogenous bone graft, removed from the mandible (bilateral oblique line and chin), followed by the installation of an immediate-load fixed cross-arch implant-supported restoration because primary stability was reached for 8 implants. In addition, instructions about masticatory function and how it is related to interfacial micromotion were addressed and emphasized to the patient. The reasons for the IL were further avoidance of an interim healing phase, a potential reduction in the number of clinical interventions for the patient, and aesthetic reasons. After monitoring the rehabilitation for 8 years, the authors can conclude that maxillary IL can be performed followed by a well-established treatment planning based on computed tomography, providing immediate esthetics and function to the patient even when autogenous bone graft was previously performed in the maxilla.

Functional Morphology of the Crop and Proventriculus of Sitophilus zeamais (Coleoptera: Curculionidae)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Low-temperature degradation of a Y-TZP ceramic after surface treatments

The purpose of this study was to evaluate the influence of zirconia surface treatments on low-temperature degradation (LTD). Disc-shaped specimens were subjected to one of four surface treatments, denoted as C (controlno surface treatment), Si (air abrasion with 30 mu m silica-modified alumina particles), Al (air abrasion with 30 mu m alumina particles), and Gr (grinding with 120 grit diamond discs). Half of the samples were submitted to autoclave treatment for 12 h (127 degrees C, 1.5 bar). Samples were characterized by x-ray diffraction and profilometer analysis and were subjected to biaxial flexural strength test. All of the groups exhibited an increase in the amount of monoclinic phase (m-phase) after LTD. The tm transformation was remarkable for the specimens from the C group, which also exhibited a significant increase in strength. The Gr group also exhibited an increase in strength but lower initial roughness, which probably suppressed LTD on the zirconia surface. The specimens subjected to air abrasion exhibited higher initial amounts of m-phase and a small increase in m-phase after LTD; the strength was not affected in these groups. The effects of LTD were different with each surface treatment applied. Apparently, LTD may be suppressed by smoother surfaces or the presence of an initial amount of m-phase on zirconia surface. (c) 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 101B: 1387-1392, 2013.

Tool Condition Monitoring of Single-Point Dresser Using Acoustic Emission and Neural Networks Models

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo da eficacia de dois adesivos dentinarios e um cimento de ionomero de vidro empregados na adesão do amalgama a dentina

Pós-graduação em Odontologia Restauradora - ICT

Avaliação laboratorial da resistência ao cisalhamento de discos de porcelana e de um polímero de vidro cimentados à dentina bovina com o emprego de cimentos adesivos

Pós-graduação em Odontologia Restauradora - ICT

Digestibilidade e tempo de retenção dos grãos de sorgo processados durante a ensilagem em equinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Utilização da mínima quantidade de lubrificante (MQL) com água no processo de retificação cilíndrica em cerâmica avançada com rebolo de ligante resino cerâmico/metálico

Pós-graduação em Engenharia Mecânica - FEB

Análise térmica do processo de retificação plana sob diferentes condições de lubrificação utilizando técnicas de transferência de calor reversa

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Transferência de calor inversa do método convencional e do otimizado de lubri-refrigeração na retificação plana tangencial

Pós-graduação em Ciência e Tecnologia de Materiais - FC

PLA/PGA copolymer as a bone substitute in maxillary sinus augmentation: histological, histometric and immunohistochemistry study in rabbits

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Uso do copolímero de PLA/PGA no processo de reparo de defeitos ósseos em tíbia de coelhos: análise histomorfométrica

Pós-graduação em Odontologia - FOA

Desidratação e retificação de etanol produzido a partir da amêndoa do caroço da manga

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)