A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Direct torque control of permanent magnet synchronous machines - analysis and implementation

Thedirect torque control (DTC) has become an accepted vector control method besidethe current vector control. The DTC was first applied to asynchronous machines,and has later been applied also to synchronous machines. This thesis analyses the application of the DTC to permanent magnet synchronous machines (PMSM). In order to take the full advantage of the DTC, the PMSM has to be properly dimensioned. Therefore the effect of the motor parameters is analysed taking the control principle into account. Based on the analysis, a parameter selection procedure is presented. The analysis and the selection procedure utilize nonlinear optimization methods. The key element of a direct torque controlled drive is the estimation of the stator flux linkage. Different estimation methods - a combination of current and voltage models and improved integration methods - are analysed. The effect of an incorrect measured rotor angle in the current model is analysed andan error detection and compensation method is presented. The dynamic performance of an earlier presented sensorless flux estimation method is made better by improving the dynamic performance of the low-pass filter used and by adapting the correction of the flux linkage to torque changes. A method for the estimation ofthe initial angle of the rotor is presented. The method is based on measuring the inductance of the machine in several directions and fitting the measurements into a model. The model is nonlinear with respect to the rotor angle and therefore a nonlinear least squares optimization method is needed in the procedure. A commonly used current vector control scheme is the minimum current control. In the DTC the stator flux linkage reference is usually kept constant. Achieving the minimum current requires the control of the reference. An on-line method to perform the minimization of the current by controlling the stator flux linkage reference is presented. Also, the control of the reference above the base speed is considered. A new estimation flux linkage is introduced for the estimation of the parameters of the machine model. In order to utilize the flux linkage estimates in off-line parameter estimation, the integration methods are improved. An adaptive correction is used in the same way as in the estimation of the controller stator flux linkage. The presented parameter estimation methods are then used in aself-commissioning scheme. The proposed methods are tested with a laboratory drive, which consists of a commercial inverter hardware with a modified software and several prototype PMSMs.

Sliding Mode Control for Switched Mode Power Supplies

Control applications of switched mode power supplies have been widely investigated. The main objective ofresearch and development (R&D) in this field is always to find the most suitable control method to be implemented in various DC/DC converter topologies. Inother words, the goal is to select a control method capable of improving the efficiency of the converter, reducing the effect of disturbances (line and load variation), lessening the effect of EMI (electro magnetic interference), and beingless effected by component variation. The main objective of this research work is to study different control methods implemented in switched mode power supplies namely (PID control, hysteresis control, adaptive control, current programmed control, variable structure control (VSC), and sliding mode control (SMC). The advantages and drawbacks of each control method are given. Two control methods, the PID and the SMC are selected and their effects on DC/DC (Buck, Boost, and Buck-Boost) converters are examined. Matlab/SimulinkTM is used to implement PID control method in DC/DC Buck converter and SMC in DC/DC (Buck, and Buck Boost) converters. For the prototype, operational amplifiers (op-amps) are used to implement PID control in DC/DC Buck converter. For SMC op-amps are implemented in DC/DC Buck converter and dSPACETM is used to control the DC/DC Buck-Boost converter. The SMC can be applied to the DC/DC (Buck, Boost, and Buck-Boost) converters. A comparison of the effects of the PID control and the SMC on the DC/DC Buck converter response in steady state, under line variations, load variations, and different component variations is performed. Also the Conducted RF-Emissions between the PID and SMC DC/DC Buck Converter are compared. The thesis shows that, in comparison with the PID control, the SMC provides better steady-state response, better dynamic response, less EMI, inherent order reduction, robustness against system uncertainty disturbances, and an implicit stability proof. Giving a better steady-state and dynamic response, the SMC is implemented in a DC/DC resonant converter. The half-wave zero current switching (HWZCS) DC/DC Buck converter is selected as a converter topology. A general guideline to select the tank component values, needed for the designing of a HWZCS DC/DC Buck, is obtained. The implementation of the SMC to a HWZCS DC/DC Buck converter is analysed. The converter response is investigated in the steady-state region and in the dynamic region.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Strategy Implementation Bottlenecks: Identification, Analysis and Removal

This thesis investigates the strategy implementation process of enterprices; a process whichhas lacked the academic attentioon compared with a rich strategy formation research trdition. Strategy implementation is viewed as a process ensuring tha the strtegies of an organisation are realised fully and quickly, yet with constant consideration of changing circumstances. The aim of this sudy is to provide a framework for identifying, analysing and removing the strategy implementation bottleneck af an organization and thus for intesifying its strategy process.The study is opened by specifying the concept, tasks and key actors of strategy implementation process; especially arguments for the critical implementation role of the top management are provided. In order to facilitate the analysis nad synthetisation of the core findings of scattered doctrine, six characteristic approaches to strategy implementation phenomenon are identified and compared. The Bottleneck Framework is introduced as an instrument for arranging potential strategy realisation problems, prioritising an organisation's implementation obstacles and focusing the improvement measures accordingly. The SUCCESS Framework is introduced as a mnemonic of the seven critical factors to be taken into account when promoting sttrategy implementation. Both frameworks are empirically tested by applying them to real strategy implementation intesification process in an international, industrial, group-structured case enterprise.

Bioinspired electronic white cane implementation based on a LIDAR, a tri-axial accelerometer and a tactile belt

This work proposes the creation of a bioinspired electronic white cane for blind people using the whiskers principle for short-range navigation and exploration. Whiskers are coarse hairs of an animal's face that tells the animal that it has touched something using the nerves of the skin. In this work the raw data acquired from a low-size terrestrial LIDAR and a tri-axial accelerometer is converted into tactile information using several electromagnetic devices configured as a tactile belt. The LIDAR and the accelerometer are attached to the user’s forearm and connected with a wire to the control unit placed on the belt. Early validation experiments carried out in the laboratory are promising in terms of usability and description of the environment.

La fonction publique en Suisse : analyse géopolitique d'un fédéralisme à géométrie variable

Bien que présenté comme un modèle de stabilité, le fédéralisme est constamment remis en question. Le but de l'article est de présenter quelques-unes de ses caractéristiques lues à travers les effectifs de la fonction publique en Suisse. Pour ce faire, nous distinguerons quatre types d'employeurs : Confédération, cantons, communes et corporations de droit public, lesquels représentent 10,5 % du total des actifs en Suisse. Nous analyserons la densité administrative, la variation des emplois et le degré de décentralisation selon la culture, le territoire et la religion. Il ressort que la fonction publique intermédiaire, c'est-à-dire les cantons, joue le premier rôle avec ses 140'000 emplois en équivalents plein temps (EPT) sur un total de 328'000, en hausse de 10,3 % par rapport à 2001. Les communes comptent 38 % des agents publics (+3,6 % par rapport à 2001), loin devant la Confédération, 11 % du total (en perte de vitesse : -1,2 %) et les corporations de droit public, 9 % du total (+14,5 %). Le taux d'administration est plus élevé dans la partie francophone que dans la partie germanophone, ainsi que dans les centres économiques et les zones frontières. Les écarts entre les cantons peuvent varier du simple au triple. En fait, deux modèles politico-administratifs transparaissent : le premier « cantonaliste » et davantage étatiste dans la partie latine, l'autre « communaliste » et décentralisé, dominant dans la partie germanophone. Le quotient de décentralisation administrative montre de grandes différences entre l'est et l'ouest, qui s'estompent toutefois avec la modernisation des institutions et le repositionnement de la Suisse face à l'Europe.

Review. Precision viticulture. Research topics, challenges and opportunities in site-specific vineyard management

Precision Viticulture (PV) is a concept that is beginning to have an impact on the wine-growing sector. Its practical implementation is dependant on various technological developments: crop sensors and yield monitors, local and remote sensors, Global Positioning Systems (GPS), VRA (Variable-Rate Application) equipment and machinery, Geographic Information Systems (GIS) and systems for data analysis and interpretation. This paper reviews a number of research lines related to PV. These areas of research have focused on four very specific fields: 1) quantification and evaluation of within-field variability, 2) delineation of zones of differential treatment at parcel level, based on the analysis and interpretation of this variability, 3) development of Variable-Rate Technologies (VRT) and, finally, 4) evaluation of the opportunities for site-specific vineyard management. Research in these fields should allow winegrowers and enologists to know and understand why yield variability exists within the same parcel, what the causes of this variability are, how the yield and its quality are interrelated and, if spatial variability exists, whether site-specific vineyard management is justifiable on a technical and economic basis.

Design and implementation of FPGA-based LQ control of active magnetic bearings

The need for high performance, high precision, and energy saving in rotating machinery demands an alternative solution to traditional bearings. Because of the contactless operation principle, the rotating machines employing active magnetic bearings (AMBs) provide many advantages over the traditional ones. The advantages such as contamination-free operation, low maintenance costs, high rotational speeds, low parasitic losses, programmable stiffness and damping, and vibration insulation come at expense of high cost, and complex technical solution. All these properties make the use of AMBs appropriate primarily for specific and highly demanding applications. High performance and high precision control requires model-based control methods and accurate models of the flexible rotor. In turn, complex models lead to high-order controllers and feature considerable computational burden. Fortunately, in the last few years the advancements in signal processing devices provide new perspective on the real-time control of AMBs. The design and the real-time digital implementation of the high-order LQ controllers, which focus on fast execution times, are the subjects of this work. In particular, the control design and implementation in the field programmable gate array (FPGA) circuits are investigated. The optimal design is guided by the physical constraints of the system for selecting the optimal weighting matrices. The plant model is complemented by augmenting appropriate disturbance models. The compensation of the force-field nonlinearities is proposed for decreasing the uncertainty of the actuator. A disturbance-observer-based unbalance compensation for canceling the magnetic force vibrations or vibrations in the measured positions is presented. The theoretical studies are verified by the practical experiments utilizing a custom-built laboratory test rig. The test rig uses a prototyping control platform developed in the scope of this work. To sum up, the work makes a step in the direction of an embedded single-chip FPGA-based controller of AMBs.

Implementation of Signaling Gateway between Telephone Network and the Internet

Tässä diplomityössä perehdytään verkkoelementiltä, joka yhdistää H.323, MEGACO- ja ISUP-protokollia käyttävät tietoliikenneverkot toisiinsa, vaadittaviin ominaisuuksiin ja toiminnallisuuksiin. Tyypillisesti tällaista toiminnallisuutta tarvitaan IP- ja PSTN-verkkojen yhdistämisessä. Tarkastelu aloitetaan kuvaamalla PSTN-verkon signalointi ja rakenne, jatketaan kuvaamalla internet-protokollia käyttävä verkkoympäristö ja lopuksi perehdytään verkkoelementiltä vaadittaviin toiminnallisuuksiin, jotta PSTN ja MEGACO-pohjaiset verkot toimivat yhteen. Työn käytännöllisenä osuutena kuvataan osa viestisekvenssikaavioista, joita verkkoelementti toteuttaa puuttumatta kuitenkaan eri protokollien toimintaan viestien parametrien tasolla.

Design,implementation and use of an Internet kiosk as an an information system for CNC machinists

Tätä diplomityötä sponsoroi suuri Isobritannialainen lentokoneteollisuudessa toimiva yritys, joka huomasi että globaalin tuotantostrategian ollessa painopisteenä ja tietoteknisten järjestelmien kuten CAD/CAM ollessa merkittävänä osana tuotantoa, on löydettävä ymmärrys siitä, mitkä ovat tuotannon tietojärjestelmien tarpeet ja onko niiden kehittämisestä hyötyä yritykselle.Diplomityössä selitetään Internet teknologiaan perustuvan kioskin kehittämisestä tietotukijärjestelmäksi tuotanto-osastolle, jossa valmistetaan moottorin osia CNC-koneilla. Kioskeissa on piirteitä, jotka voisivat osoittautua hyödyllisiksi myös tuotantoympäristöissä ja siksi tässä työssä tutkitaan kioskiin perustuvaa lähestymistapaa tuotantoympäristöön sovellettuna.Diplomityö kuvaa informaatiokioskin kehittämistä alkaen alkuvaatimusten keruusta tietojärjestelmää varten, tietojärjestelmän suunnittelu- ja kehitysvaiheen sekä lopuksi analysoi kioskin onnistuneisuutta tuotantoympäristössä käytettävyystutkimuksen avulla, joka suoritettiin sen jälkeen kun kioski oli implementoitu tehtaassa.Johtopäätökset osoittavat, että kioski on hyvin implementoitavissa tuotantoympäristöön ja todistaa, että tuotantoinformaation jakelu sähköisessä muodossa on huomattavasti tehokkaampaa kuin paperilla. Käyttäjien kommentit osoittavat että kioski on sopiva heidän tietotarpeisiinsa ja siitä on hyötyä heidän työlleen. Kioski tarjoaa hyötyjä tuotantotason lisäksi myös johtotasolle.

Code Generator for Key Management Protocols - Design and Implementation

Key management has a fundamental role in secure communications. Designing and testing of key management protocols is tricky. These protocols must work flawlessly despite of any abuse. The main objective of this work was to design and implement a tool that helps to specify the protocol and makes it possible to test the protocol while it is still under development. This tool generates compile-ready java code from a key management protocol model. A modelling method for these protocols, which uses Unified Modeling Language (UML) was also developed. The protocol is modelled, exported as an XMI and read by the code generator tool. The code generator generates java code that is immediately executable with a test software after compilation.

Tobacco control policies in hospitals before and after the implementation of a national smoking ban in Catalonia, Spain

Background: Diverse projects and guidelines to assist hospitals towards the attainment of comprehensive smoke-free policies have been developed. In 2006, Spain government passed a new smoking ban that reinforce tobacco control policies and banned completely smoking in hospitals. This study assesses the progression of tobacco control policies in the Catalan Network of Smokefree Hospitals before and after a comprehensive national smoking ban. Methods: We used the Self-Audit Questionnaire of the European Network for Smoke-free Hospitals to score the compliance of 9 policy standards (global score = 102). We used two crosssectional surveys to evaluate tobacco control policies before (2005) and after the implementation of a national smoking ban (2007) in 32 hospitals of Catalonia, Spain. We compared the means of the overall score in 2005 and 2007 according to the type of hospital, the number of beds, the prevalence of tobacco consumption, and the number of years as a smoke-free hospital. Results: The mean of the implementation score of tobacco control policies was 52.4 (95% CI:45.4-59.5) in 2005 and 71.6 (95% CI: 67.0-76.2) in 2007 with an increase of 36.7% (p < 0.01). The hospitals with greater improvement were general hospitals (48% increase; p < 0.01), hospitals with > 300 beds (41.1% increase; p < 0.01), hospitals with employees' tobacco consumption prevalence 35-39% (72.2% increase; p < 0.05) and hospitals that had recently implemented smoke-free policies (74.2% increase; p < 0.01). Conclusion: The national smoking ban appears to increase tobacco control activities in hospitals combined with other non-bylaw initiatives such as the Smoke-free Hospital Network.

Tobacco control policies in hospitals before and after the implementation of a national smoking ban in Catalonia, Spain

Background: Diverse projects and guidelines to assist hospitals towards the attainment of comprehensive smoke-free policies have been developed. In 2006, Spain government passed a new smoking ban that reinforce tobacco control policies and banned completely smoking in hospitals. This study assesses the progression of tobacco control policies in the Catalan Network of Smokefree Hospitals before and after a comprehensive national smoking ban. Methods: We used the Self-Audit Questionnaire of the European Network for Smoke-free Hospitals to score the compliance of 9 policy standards (global score = 102). We used two crosssectional surveys to evaluate tobacco control policies before (2005) and after the implementation of a national smoking ban (2007) in 32 hospitals of Catalonia, Spain. We compared the means of the overall score in 2005 and 2007 according to the type of hospital, the number of beds, the prevalence of tobacco consumption, and the number of years as a smoke-free hospital. Results: The mean of the implementation score of tobacco control policies was 52.4 (95% CI:45.4-59.5) in 2005 and 71.6 (95% CI: 67.0-76.2) in 2007 with an increase of 36.7% (p < 0.01). The hospitals with greater improvement were general hospitals (48% increase; p < 0.01), hospitals with > 300 beds (41.1% increase; p < 0.01), hospitals with employees' tobacco consumption prevalence 35-39% (72.2% increase; p < 0.05) and hospitals that had recently implemented smoke-free policies (74.2% increase; p < 0.01). Conclusion: The national smoking ban appears to increase tobacco control activities in hospitals combined with other non-bylaw initiatives such as the Smoke-free Hospital Network.