Electrode characteristics and microstructure of AB(2)-AB(5) composite hydrogen storage alloy formed by ball-milling process

For improving the electrode characteristics of the Zr-based AB(2)-type alloy, a new kind of composite hydrogen Zr0.9Ti0.1(Ni0.50Mn0.35V0.15)(2)(represented as AB(2)) with a rare storage alloy was successfully prepared by ball-milling I earth-based AB(5)-type alloy (represented as AB(5)) which worked as a surface modifier. Effects of ball-milling on the electrode characteristics and microstructure of Zr0.9Ti0.1(Ni0.50Mn0.35V0.15)(2) alloy and mixtures of AB(2) with AB(5) alloy were investigated. After milling the mixed AB(2) and AB(5) powders (9: 1 in mass ratio) for 10min, XRD and SEM analysis showed that AB(2) and AB(5) maintained their original crystalline states, respectively, some AB(5) particles were adhered onto the surface of AB(2), and some fresh surfaces were formed. It was found that the activation cycles of AB(2)-AB(5) composite alloy was shortened from 14 to 7 and the maximum discharge capacity was increased from 330mAh . g(-1) to 347mAh . g(-1) as compared with AB(2) alloy. The discharge rate capability of AB(2) alloy was also improved by ball milling AB(2) with AB(5) alloy process. The combined effect of ball-milling and mixing with AB(5) alloy is superior to that of sole treatment. It was believed that AB(5) alloy works not only as a regular hydrogen storage alloy, but also as a surface modifier to catalyze the hydriding/ dehydriding process of AB(2) alloy.

Electrochemical characteristic of LaNi-based hydrogen storage alloys

Effect of purity of alloy components on the electrode performance of LaNi2 alloys was investigated. The results showed the purity of components had less effect on discharge capacity and self-discharge of LaNi2 alloys. Partial substitution of Al or Mn for Ni greatly improved discharge properties of LaNi2-xAlx, or LaNi2-yMny alloys as negative electrodes in MFl-Ni battery, 0.15less than or equal toxless than or equal to0.25; 0.15less than or equal toyless than or equal to0.25. In addition, surface treatment of LaNi1.8Al0.2 alloy electrode was performed by polymerizing cis-butenedioate with Co-60- gamma -ray radiation, which. had better affect on self-discharge and cycle life of the alloy electrodes at low temperature(-28 C-degrees).

BaLiF3(Eu2+): A promising X-ray storage phosphor

The TSL glow of X-irradiated BaLiF3 crystallite vanished within 15 min of sunlight bleaching or after 2 similar to 3 days of room temperature annealing, which indicate that X-irradiation damage is light and can be easily erased. It is also found that BaLiF3:Eu2+ is photostimulatable and seems be a promising X-ray storage phosphor for practical utilization.

Effect of storage time and cryoprotectant concentrations on the fertilization rate and hatching rate of cryopreserved sperm in red seabream (Pagrus major Temminck & Schlegel, 1843)

This study examined the effects of storage time and cryoprotectant concentrations on the post-thaw sperm of red seabream, Pagrus major. Sperm treated with 12%, 15%, 18% and 21% DMSO were cryopreserved for 10, 30, 60 and 360 days, and fertilization and hatching rates were analysed. For all groups, there were no differences in the fertilization rates and hatching rates between sperm cryopreserved for < 60 days and fresh sperm (98.8 +/- 0.8%, 96.4 +/- 1.3%). However, for sperm cryopreserved for 360 days, both fertilization rates (88.6 +/- 3.0% to 7.0 +/- 1.9%) and hatching rates (79.4 +/- 7.2% to 3.3 +/- 0.8%) decreased drastically. Furthermore, the cryoprotectant concentrations affected sperm quality significantly (P < 0.05). When cryopreserved for 360 days, sperm treated with 15% DMSO obtained the best results compared with other concentrations. We suggest that 15% DMSO may be an effective cryoprotectant for long-term sperm cryopreservation of red seabream.

Soil organic carbon storage and soil CO2 flux in the alpine meadow ecosystem

High-resolution sampling, measurements of organic carbon contents and C-14 signatures of selected four soil profiles in the Haibei Station situated on the northeast Tibetan Plateau, and application of C-14 tracing technology were conducted in an attempt to investigate the turnover times of soil organic carbon and the soil-CO2 flux in the alpine meadow ecosystem. The results show that the organic carbon stored in the soils varies from 22.12x10(4) kg C hm(-2) to 30.75x10(4) kg C hm(-2) in the alpine meadow ecosystems, with an average of 26.86x10(4) kg C hm(-2). Turnover times of organic carbon pools increase with depth from 45 a to 73 a in the surface soil horizon to hundreds of years or millennia or even longer at the deep soil horizons in the alpine meadow ecosystems. The soil-CO2 flux ranges from 103.24 g C m(-2) a(-1) to 254.93 gC m(-2) a(-1), with an average of 191.23 g C m(-2) a(-1). The CO2 efflux produced from microbial decomposition of organic matter varies from 73.3 g C m(-2) a(-1) to 181 g C m(-2) a(-1). More than 30% of total soil organic carbon resides in the active carbon pool and 72.8%. 81.23% of total CO2 emitted from organic matter decomposition results from the topsoil horizon (from 0 cm to 10 cm) for the Kobresia meadow. Responding to global warming, the storage, volume of flow and fate of the soil organic carbon in the alpine meadow ecosystem of the Tibetan Plateau will be changed, which needs further research.

New Timber Architecture in Scotland.

New Timber Architecture in Scotland illustrates 90 exemplar projects and demonstrates clearly that there is no single building type unsuited to the use of this adaptable, variable and infinitely renewable material. Too long out of fashion, timber is now widely specified and has become an important design element in some of the most innovative projects being built today. The projects selected for inclusion are not the work of a few superstar architects: they represent the output of a significant percentage of architectural practices in Scotland and illustrate a burgeoning confidence in timber as an exciting, contemporary construction material. New Timber Architecture in Scotland aims to stimulate others to follow their lead.

Moisture conditions in timber cladding: field trial data for Sitka spruce.

Exposure trials on timber cladding are valuable for informing facade designers. This paper describes a trial using Sitka spruce (Picea sitchensis). Sitka spruce is the only UK-grown timber available in sufficient volume to supply the growing cladding market, but its suitability is unclear. Data indicated that the moisture content range in timber cladding was wider than generally accepted. The minimum of around 10% moisture content appeared to be similar for all details tested. The maximum was influenced by construction detailing but was around 30%. From a theoretical standpoint, the range, and rate, of moisture content fluctuation observed meant that the commonly quoted average value was largely irrelevant. The mode was a more representative statistic; most of the data were skewed towards the wood's fibre saturation point. Sitka spruce is, therefore, at risk of fungal decay and is only suitable as external cladding in the UK if treated with preservative

Evidence-based design of timber facades’.

Conference paper on a CD-Rom

Timber grading seminar - Some things you should know about how strength grading works and what is changing in the standards.

Presentations from the seminar on timber grading. "This grading seminar will give you a crash course in timber strength grading, what it is, how it works, and how it is changing. It aims to demystify timber grading, tackle some widely held misconceptions, and tell you the things you need to be aware of to improve profitability, and remain correct and safe in what you do. The timber resource in the UK is changing, technology is advancing, and standards are being modified. This seminar will bring you the latest position, informed by CEN and BSI standards committee work and research conducted by the SIRT network."

Strength grading of sawn timber in Europe: an explanation for engineers and researchers.

This paper is a concise explanation of the normative background to strength grading in Europe, addressing important aspects that are commonly misunderstood by structural engineers and timber researchers. It also highlights changes that are being made to the standards to: incorporate requirements of the construction products regulations; add improvements to the system to accommodate the latest knowledge and technology; and widen the application of the standards. Where designs need to be optimised, there is an opportunity to use the system more intelligently, in combination with the latest technology, to better fit design values to the true properties of the timber resource. This can bring a design enhancement equivalent to effort improving other aspects of the structure, such as connectors and reinforcement. Parallel to this, researchers working on other aspects of structural improvement need to understand what grades really mean in respect of the properties of the timber, in order to correctly analyse the results of testing. It is also useful to know how techniques used in grading can assist with material properties characterisation for research. The amount of destructive testing involved in establishing machine grading settings and visual grading assignments presents a barrier to greater use of local timber, and diversification of commercial species, so it is important that any researcher assessing the properties of such species should consider, from the outset, doing the research in a way that can contribute to a grading dataset at a later date. This paper provides an overview of what is required for this.

Sole plate fixing details for modern methods of timber construction.

In order to resist lateral loads, modern methods of timber construction are reliant on the in-plane shear strength of the walls orientated parallel to the applied action. In closed panel systems, the shear stresses are transferred to the foundations by the sole plate through the sheathing board, which is usually mechanically jointed to the timber frame. Since closed panels are delivered to site as single units, access to the internal bottom rail is rather restricted and novel, efficient solutions to secure the panel to the substrate are required. Sole plate fixing components for open and closed panel systems were tested in isolation and combination in order to validate a simplistic version of the weakest link theory. As a result, findings were embedded into a software database with a direct link to a previously developed sole plate and racking design application. This integrated process facilitates the structural optimization of the sole plate detail.

Working Memories for Storage and Recall of Arbitrary Temporal Sequences

A working memory model is described that is capable of storing and recalling arbitrary temporal sequences of events, including repeated items. These memories encode the invariant temporal order of sequential events that may be presented at widely differing speeds, durations, and interstimulus intervals. This temporal order code is designed to enable all possible groupings of sequential events to be stably learned and remembered in real time, even as new events perturb the system.

Store Working Memory Networks for Storage and Recall of Arbitrary Temporal Sequences

Neural network models of working memory, called Sustained Temporal Order REcurrent (STORE) models, are described. They encode the invariant temporal order of sequential events in short term memory (STM) in a way that mimics cognitive data about working memory, including primacy, recency, and bowed order and error gradients. As new items are presented, the pattern of previously stored items is invariant in the sense that, relative activations remain constant through time. This invariant temporal order code enables all possible groupings of sequential events to be stably learned and remembered in real time, even as new events perturb the system. Such a competence is needed to design self-organizing temporal recognition and planning systems in which any subsequence of events may need to be categorized in order to to control and predict future behavior or external events. STORE models show how arbitrary event sequences may be invariantly stored, including repeated events. A preprocessor interacts with the working memory to represent event repeats in spatially separate locations. It is shown why at least two processing levels are needed to invariantly store events presented with variable durations and interstimulus intervals. It is also shown how network parameters control the type and shape of primacy, recency, or bowed temporal order gradients that will be stored.

Hybrid energy storage for energy harvesting powered wireless sensor networks

Science Foundation Ireland (CSET - Centre for Science, Engineering and Technology, grant 07/CE/I1147); Scientific Foundation Ireland (ITOBO (398-CRP))