Impacts of climate change on water resources in the Mediterranean basin : a case study in Catalonia, Spain

Most climate change projections show important decreases in water availability in the Mediterranean region by the end of this century. We assess those main climate change impacts on water resources in three medium-sized catchments with varying climatic conditions in north-eastern Spain. A combination of hydrological modelling and climate projections with B1 and A2 IPCC emission scenarios is performed to infer future stream flows. The largest reduction (22-48% for 2076-2100) of stream flows is expected in the headwaters of the two wettest catchments, while lower decreases (22-32% for 2076-2100) are expected in the drier one. In all three catchments, autumn and summer are the seasons with the most notable projected decreases in stream flow, 50% and 34%, respectively (2076-2100). Thus, ecological flows might be noticeably impacted by climate change in the catchments, especially in the headwaters of those wet catchments.

High encapsulation efficiency of sodium alendronate in eudragit S100/HPMC blend microparticles

The hydrophilic drug sodium alendronate was encapsulated in blended microparticles of Eudragit® S100 and Methocel® F4M or Methocel® K100LV. Both formulations prepared by spray-drying showed spherical collapsed shape and smooth surface, encapsulation efficiencies of 85 and 82% and mean diameters of 11.7 and 8.4 µm, respectively. At pH 1.2, in vitro dissolution studies showed good gastro-resistance for both formulations. At pH 6.8, the sodium alendronate release from the microparticles was delayed and was controlled by Fickian diffusion. In conclusion, the prepared microparticles showed high encapsulation efficiency of sodium alendronate presenting gastro-resistance and sustained release suitable for its oral administration.

Avaliação da porosidade de microcápsulas contendo proteína bioativa por porosimetria de mercúrio e adsorção de nitrogênio

Microcapsules containing lactoferrin were produced by spray drying using dextrin:octenylsuccinate starch, as wall materials. Porosity characteristics of spray-dried microcapsules were investigated by mercury intrusion porosimetry and nitrogen adsorption. The outer and inner structures of microcapsules were studied by Scanning Electron Microscopy and sizes were determined by Laser Diffraction. Results indicate that all microcapsules presents adsorption isotherm of type II and that micropores on the microcapsules surface will be very few or none. Our results show that microstructure, surface area and size of microcapsules are affected by dextrin: octenylsuccinate starch proportion. Pore characteristics for various microcapsules are found to be different.

Química forense: perspectivas sobre novos métodos analíticos aplicados à documentoscopia, balística e drogas de abuso

In this review recent methods developed and applied to solve criminal occurences related to documentoscopy, ballistic and drugs of abuse are discussed. In documentoscopy, aging of ink writings, the sequence of line crossings and counterfeiting of documents are aspects to be solved with reproducible, fast and non-destructive methods. In ballistic, the industries are currently producing ''lead-free'' or ''nontoxic'' handgun ammunitions, so new methods of gunshot residues characterization are being presented. For drugs analysis, easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to provide a relatively simple and selective screening tool to distinguish m-CPP and amphetamines (MDMA) tablets, cocaine and LSD.

Desenvolvimento e uso do compósito de Nb2O5|Cu como revestimento aplicado por aspersão térmica sobre o aço AISI 1020 para proteção contra a corrosão pelo solo em estruturas enterradas

An Nb2O|Cu corrosion-resistant coating was developed and applied onto AISI 1020 steel substrate by Powder Flame Spray. A galvanostatic electrochemical technique was employed, with and without ohmic drop, in four different soils (two corrosively aggressive and two less aggressive). Behavior of coatings in different soils was compared using a cathodic hydrogen reduction reaction (equilibrium potential, overvoltage and exchange current density) focusing on the effect of ohmic drop. Results allow recommendation of Nb2O5|Cu composite for use in buried structure protection.

Simultaneous determination of four phenolic compounds in extracts of aerial parts of Ipomoea pes-caprae (L.) R. Br. (Convolvulaceae) by HPLC-UV

Among other applications, Ipomoea pes-caprae is popularly used to treat jellyfish stings, supporting the development of a product for dermatological use. Hydroethanolic spray-dried extract was chosen for the further development of phytomedicines, and a stability-indicative HPLC-UV method was developed and validated for the determination of isoquercitrin and isochlorogenic acids A, B and C. The method was developed using a C18 column (250 x 4.6 mm, 5 µm) with an acetonitrile:water mobile phase at pH 3.0 in a gradient run. The four constituents and other unidentified components of the extract were appropriately resolved without interference of degradation products after stress tests (acid, alkali, neutral, oxidant, photolysis). The method showed linearity in the isoquercitrin concentration range from 5.0-50.0 µg mL-1, with adequate precision (RSD% < 2.5% for the intra- and inter-day studies), accuracy (recovery of 100.0 ± 2.0%), and robustness. Both the herbal drug and spray-dried extract of I. pes-caprae were subjected to stability studies in accelerated and long-term conditions over four months. The samples maintained their characteristics and marker contents (< 10% of variation).

Cotton resistance to ramulose and variability of Colletotrichum gossypii f. sp. cephalosporioides

Four cultivars and 21 lines of cotton were evaluated for resistance to ramulose (Colletotrichum gossypii f. sp. cephalosporioides) in a field where the disease is endemic. The seeds of each genotype were planted in 5 x 5 m plots with three replications. The lines CNPA 94-101 and 'CNPA Precoce 2'were used as standard susceptible and resistant references, respectively. The disease incidence (DI) was calculated from the proportion of diseased plants in the plot. The disease index (DIn) was calculated from the disease severity using a 1 to 9 scale, and was evaluated at weekly intervals starting 107 days after emergence. The data collected was used to calculate the area under disease progress curve (AUDPC). In general, the DIn increased linearly with time and varied from 20.0 to 57.1 and AUDPC from 567 to 1627 among the genotypes which could be clustered in to two distinct groups. The susceptible group contained two cultivars and nine lines and the resistant group contained one cultivar and 12 lines. The relationship between disease index and evaluation times was linear for the 25 genotypes tested. The line CNPA 94-101, used as susceptible standard, was the most susceptible with an average DI = 83.4, DIn = 57.1 and AUDPC = 1627.7. The line CNPA 96-08 with DI = 37.8, DIn = 20.0 and AUDPC = 567.7 was the most resistant one. Among the commercial cultivars 'IAC 22' was the most susceptible and 'CNPA Precoce 2', used as resistant standard was the most resistant. The variability in virulence of the pathogen was studied by spray inoculating nine genotypes with conidial suspensions (10(5)/mL) of either of the 10 isolates. The disease severity was evaluated 30 days later using a scale of 1 to 5. The virulence of the isolate was expressed by DIn. All the isolates were highly virulent but their virulence avaried for several genotypes and could be clustered in two distinct groups of less and more virulent isolates. The isolate MTRM 14 from Mato Grosso was the least virulent while Minas Gerais was the most virulent, with DIn of 6.36 and 46.47, respectively. In this experiment the line HR 102 and the cultivar 'Antares' were the most resistant ones with DIns of 18.32 and 19.14, respectively.

Reactive dissolution of sedimentary rocks in flue gas desulfurization : modeling and experimental investigation

Svavel förekommer i kol och olja och oxideras vid förbränning till svaveldioxid (SO2). Årligen utsläpps stora mängder svaveldioxid som åstadkommer sura regn, minskning av stratosfäriskt ozon och sjukdomar. Av dessa orsaker är det nödvändigt att minska utsläppen av svaveldioxid. Den teknologi som rör planering av reaktorer och processer för rökgasavsvavling (FGD) har utvecklats kraftigt och idag använder man olika typer av lösningar. De vanligaste alternativen för FGD är våtskrubber- och semitorra skrubbersystem (Spray Dry Scrubbers, SDS) och injektionsprocesser för absorbenter. SDS-processer har studerats bland annat av Ahlbeck [4] och Klingspor [5] och injektionsprocesser av Alvfors [6]. Kalksten, som i huvusak består av kalciumkarbonat, används i rökgasavsvavling på grund av sin förmåga att binda svavel i form av sulfatsalter. Den vanligaste rökgasavsvavlingsmetoden är våtskrubbning, där det sedimentära stenmaterialets upplösningshastighet är en av de faktorer som påverkar resultatet mest. Utvärdering av kalkstensreaktivitet är därför speciellt viktig vid planering och drift av anläggningar för rökgasavsvavling. Målsättningen med detta arbete var att modellera upplösningen av olika typers kalksten för att få en kvantitativ utvärdering av kvaliteten på de analyserade proverna. Därtill testades även karbonatbiprodukter från stålindustrin för att utvärdera möjligheter att använda andra råmaterial. Det transienta förloppet har analyserats, varvid upplösningshastigheten modellerades bl.a. i avseende på tid och pH. Under arbetets gång har antalet empiriska korrelationer minskats till fördel för fysikaliska modeller av diffusiva och konvektiva masstransportfenomen. En målsättning var att skapa en effektiv och snabb metod för att testa olika absorbenter för rökgasavsvavling under transienta förlopp. I arbetet användes PSD-analys, gjordes pH-mätningar och andra utvärderingar av de fysikaliska parametrar som ingår i beräkningarna. On-line mätningar för de icke-stationära variablerna tid och pH ger möjlighet att eliminera osäkerheter. Vissa modeller kan vara komplicerade. En modell för upplösningshastigheten med mer detaljerad utvärdering av parametrar och färre approximationer är därför nödvändig då man vill utvärdera reaktionshastigheten för fasta partiklar i sur miljö. Arbetet utfördes under fyra år och fem peer review-artiklar ingår i avhandlingen.

Relationship between IC50determined in vitro/in vivoand the fungicide rate used in the Field

Published data containing fungicide concentrations that control 50% (IC50) of a given fungus were analyzed. In the analysis we considered: (i) the IC50 determined in vitroand in vivofor a given fungicide and for a specific fungus; (ii) the concentration (g/ha) of active ingredient for the fungicide indicated to control a specific disease in the field; (iii) water volume of 120/L used in the spray; (iv) the fungicide a.i. concentration (mg/L) in 120 L volume; (v) and the ratio of the concentration used in the field with that determined in the laboratory. The analysis were performed by using IC50 data for DMIs, QoIs, a carbamate and a benzimidazol against the following fungi Bipolaris sorokiniana, Drechslera tritici-repentis, D. siccans, Fusarium graminearum, Puccinia triticina, Exserohilum turcicum, Phakopsora pachyrhiziand Corynespora cassiicola. The fungicide concentrations sprayed in the field were 33.9 (D. siccansand trifloxystrobin) to 500,000.0 (E. turcicumand iprodione) times higher than that determined in the laboratory. It was concluded that the IC50 was not related to the concentration used in the field and therefore should be used to compare the power among fungicides and to monitor the fungal sensitivity shift towards fungicides

Objective Evaluation of Nasal Dimensions in Children with Acoustic Rhinometry

Aims: This study was carried out to investigate the usefulness of acoustic rhinometry in the evaluation of intranasal dimensions in children. The aim was to define reference values for school children. In addition, the role of the VAS scale in the subjective evaluation of nasal obstruction in children was studied. Materials and methods: Measurements were done with Acoustic Rhinometry A1. The values of special interest were the minimal cross-sectional area (MCA) and the anterior volume of the nose (VOL). The data for reference values included 124 voluntary school children with no permanent nasal symptoms, aged between 7 and 14 years. Data were collected at baseline and after decongestion of the nose; the VAS scale was filled in before measurements. The subjects in the follow-up study (n=74, age between 1 and 12 years) were receiving intranasal spray of insulin or placebo. The nasal symptoms were recorded and acoustic rhinometry was measured at each control visit. Results: In school children, the mean total MCA was 0.752 cm2 (SD 0.165), and the mean total VOL was 4.00 cm3 (SD 0.63) at baseline. After decongestion, a significant increase in the mean TMCA and in the mean TVOL was found. A correlation was found between TMCA and age, and between TVOL and height of a child. There was no difference between boys and girls. A correlation was found between unilateral acoustic values and VAS at baseline, but not after decongestion. No difference wasfound in acoustic values or symptoms between the insulin and placebo group in the follow-up study of two years. Conclusions: Acoustic rhinometry is a suitable objective method to examine intranasal dimensions in children. It is easy to perform and well tolerated. Reference values for children between 7 and 14 years were established.

DIFFERENTIAL RESPONSE OF CLONES OF EUCALYPT TO GLYPHOSATE1

Weed control is commonly performed by the inter-row mechanical weeding associated to intrarow glyphosate directed spraying, causing a risk for drift or accidental herbicide application, that can affect the crop of interest. The objective was to evaluate the response of clones C219, GG100, I144, and I224 of eucalypt (Eucalyptus grandis x E. urophylla) to glyphosate doses of 0, 18, 36, 72, 180, 360, and 720 g of acid equivalent per hectare. The clones showed different growth patterns with regard to height, leaf number, stem dry weight, relative growth rate, net assimilation rate, and relative leaf growth rate. The clones I144 and GG100 were more susceptible to glyphosate, showing the doses required to reduce dry weight by 50% of 113.4 and 119.6 g acid equivalent per hectare, respectively. The clones C219 and I224 were less susceptible to glyphosate, showing the doses required to reduce dry weight by 50% of 237.5 and 313.5 g acid equivalent per hectare, respectively. Eucalyptus clones respond differently to glyphosate exposure, so that among I224, C219, GG100, and I144, the susceptibility to the herbicide is increasing.

Modelagem de um condicionador de ar de alta precisão para uso em processamento agrícola

Apresenta-se neste trabalho, estudo detalhado sobre a modelagem de um condicionador de ar com controle acurado de temperatura e umidade relativa. Desenvolveu-se um programa de computador que permite predizer o comportamento do sistema sob diferentes condições psicrométricas e de vazão do ar de entrada. O modelo global físico-matemático inclui equações de balanço de massa e de energia para três diferentes volumes de controle que compõem o condicionador. Modelaram-se os processos de mistura, evaporação (ou condensação) simultânea de uma superfície d'água e de uma gota e o aquecimento de corrente de ar, separadamente. Propõem-se expressões semi-empíricas simples para os coeficientes de transferência de calor e massa inerentes ao processo de evaporação sobre uma superfície d'água e um modelo simplificado para o sistema de spray. Construiu-se um condicionador de ar no qual foram feitos testes experimentais para o ajuste das constantes que aparecem nas expressões para os coeficientes de transferência. Os dados obtidos validaram o modelo global, com precisão aceitável para projetos de engenharia.

Optimization of the refining and shoe press in board production

Optimointi on tavallinen toimenpide esimerkiksi prosessin muuttamisen tai uusimisen jälkeen. Optimoinnilla pyritään etsimään vaikkapa tiettyjen laatuominaisuuksien kannalta paras tapa ajaa prosessia tai erinäisiä prosessin osia. Tämän työn tarkoituksena oli investoinnin jälkeen optimoida neljä muuttujaa, erään runkoon menevän massan jauhatus ja määrä, märkäpuristus sekä spray –tärkin määrä, kolmen laatuominaisuuden, palstautumislujuuden, geometrisen taivutusjäykkyyden ja sileyden, suhteen. Työtä varten tehtiin viisi tehdasmittakaavaista koeajoa. Ensimmäisessä koeajossa oli tarkoitus lisätä vettä tai spray –tärkkiä kolmikerroskartongin toiseen kerrosten rajapintaan, toisessa koeajossa muutettiin, jo aiemmin mainitun runkoon menevän massan jauhatusta ja jauhinkombinaatioita. Ensimmäisessä koeajossa tutkittiin palstautumislujuuden, toisessa koeajossa muiden lujuusominaisuuksien kehittymistä. Kolmannessa koeajossa tutkittiin erään runkoon menevän massan jauhatuksen ja määrän sekä kenkäpuristimen viivapaineen muutoksen vaikutusta palstautumislujuuteen, geometriseen taivutusjäykkyyteen sekä sileyteen. Neljännessä koeajossa yritettiin toistaa edellisen koeajon paras piste ja parametreja hieman muuttamalla saada aikaan vieläkin paremmat laatuominaisuudet. Myös tässä kokeessa tutkittiin muuttujien vaikutusta palstautumislujuuteen, geometriseen taivutusjäykkyyteen ja sileyteen. Viimeisen kokeen tarkoituksena oli tutkia samaisen runkoon menevän massan vähentämisen vaikutusta palstautumislujuuteen. Erinäisistä vastoinkäymisistä johtuen, koeajoista saadut tulokset jäivät melko laihoiksi. Kokeista kävi kuitenkin ilmi, että lujuusominaisuudet eivät parantuneet, vaikka jauhatusta jatkettiin. Lujuusominaisuuksien kehittymisen kannalta turha jauhatus pystyttiin siis jättämään pois ja näin säästämään energiaa sekä säästymään pitkälle viedyn jauhatuksen mahdollisesti aiheuttamilta muilta ongelmilta. Vähemmällä jauhatuksella ominaissärmäkuorma saatiin myös pidettyä alle tehtaalla halutun tason. Puuttuvat lujuusominaisuudet täytyy saavuttaa muilla keinoin.

Otimização da eficiência de limpeza em equipamento de beneficiamento de tomate de mesa

A etapa de limpeza no sistema de beneficiamento do tomate de mesa é essencial para a aceitação do produto pelo consumidor, pois o grau de limpeza dos frutos está diretamente relacionado com a qualidade do produto. Entretanto, a etapa de lavagem, nos atuais equipamentos de limpeza, utilizada em unidades comerciais de beneficiamento, demanda volume excessivo de água, trazendo sérias preocupações ambientais. Este trabalho teve como objetivo comparar a eficiência de limpeza em dois sistemas, avaliando diferentes configurações operacionais relacionadas com a rotação de escovas, vazão do sistema e tempo de permanência do fruto sobre o jato. Comparou-se o sistema convencional utilizado em equipamentos comerciais com o sistema composto por um bocal de spray do tipo cone cheio. Os resultados demonstraram que a eficiência de limpeza não está diretamente relacionada com o volume de água utilizado, mas, sim, à pressão da água, associado ao tempo de permanência dos frutos e à rotação das escovas. Portanto, o uso de spray em sistemas de limpeza de frutos de tomate pode trazer benefícios tanto para a eficiência de limpeza, com incrementos superiores a 13%, como para o meio ambiente, trazendo redução no consumo de água.

Measurement systems of soil water matric potential and evaluation of soil moisture under different irrigation depths

The development of new methodologies and tools that enable to determine the water content in soil is of fundamental importance to the practice of irrigation. The objective of this study was to evaluate soil matric potential using mercury tensiometer and puncture digital tensiometer, and to compare the gravimetric soil moisture values obtained by tensiometric system with gravimetric soil moisture obtained by neutron attenuation technique. Four experimental plots were maintained with different soil moisture by irrigation. Three repetitions of each type of tensiometer were installed at 0.20 m depth. Based on the soil matric potential and the soil water retention curve, the corresponding gravimetric soil moisture was determined. The data was then compared to those obtained by neutron attenuation technique. The results showed that both tensiometric methods showed no difference under soil matric potential higher than -40 kPa. However, under drier soil, when the water was replaced by irrigation, the soil matric potential of the puncture digital tensiometer was less than those of the mercury tensiometer.