Long-term effects of physical activity level on changes in healthy body mass index over 12 years in young adult women

Objectives To examine the effects of overall level and timing of physical activity (PA) on changes from a healthy body mass index (BMI) category over 12 years in young adult women. Patients and Methods Participants in the Australian Longitudinal Study on Women's Health (younger cohort, born 1973-1978) completed surveys between 2000 (age 22-27 years) and 2012 (age 34-39 years). Physical activity was measured in 2000, 2003, 2006, and 2009 and was categorized as very low, low, active, or very active at each survey, and a cumulative PA score for this 9-year period was created. Logistic regression was used to examine relationships between PA accumulated across all surveys (cumulative PA model) and PA at each survey (critical periods PA model), with change in BMI category (from healthy to overweight or healthy to obese) from 2000 to 2012. Results In women with a healthy BMI in 2000, there were clear dose-response relationships between accumulated PA and transition to overweight (P=.03) and obesity (P<.01) between 2000 and 2012. The critical periods analysis indicated that very active levels of PA at the 2006 survey (when the women were 28-33 years old) and active or very active PA at the 2009 survey (age 31-36 years) were most protective against transitioning to overweight and obesity. Conclusion These findings confirm that maintenance of very high PA levels throughout young adulthood will significantly reduce the risk of becoming overweight or obese. There seems to be a critical period for maintaining high levels of activity at the life stage when many women face competing demands of caring for infants and young children.

Accurate determination of interference in pin joints Pin-to-plate interference in experimental models of interference-fit joints is significantly overestimated by direct physical measurements, but it can be accurately determined by a simple photoelastic method

Suitable pin-to-hole interference can significantly increase the fatigue life of a pin joint. In practical design, the initial stresses due to interference are high and they are proportional to the effective interference. In experimental studies on such joints, difficulties have been experienced in estimating the interference accurately from physical measurements of pin and hole diameters. A simple photoelastic method has been developed to determine the effective interference to a high degree of accuracy. This paper presents the method and reports illustrative data from a successful application thereof.

Physical activity and diabetic complications in patients with type 1 diabetes

Type 1 diabetes is associated with the risk for late diabetic complications which are divided into microvascular (retinopathy, nephropathy, and neuropathy) and macrovascular (cardiovascular disease, CVD) diseases. The risk for diabetic complication can be reduced by effective treatment, most importantly the glycaemic control. Glycaemia in type 1 diabetes is influenced by the interplay between insulin injections and lifestyle factors such as physical activity and diet. The effect of physical activity in patients with type 1 diabetes is not well known, however. The aim of this thesis was to investigate the physical activity and the physical fitness of patients with type 1 diabetes with special emphasis on glycaemic control and the diabetic complications. The patients included in the study were all part of the nationwide, multicenter Finnish Diabetic Nephropathy (FinnDiane) Study which aims to characterise genetic, clinical, and environmental factors that predispose to diabetic complications in patients with type 1 diabetes. In addition, subjects from the IDentification of EArly mechanisms in the pathogenesis of diabetic Late complications (IDEAL) Study were studied. Physical activity was assessed in the FinnDiane Study in 1945 patients by a validated questionnaire. Physical fitness was measured in the IDEAL Study by spiroergometry (cycle test with measurement of respiratory gases) in 86 young adults with type 1 diabetes and in 27 healthy controls. All patients underwent thorough clinical characterisation of their diabetic complication status. Four substudies were cross-sectional using baseline data and one study additionally used follow-up data. Physical activity, especially the intensity of activities, was reduced in patients affected by diabetic nephropathy, retinopathy, and CVD. Low physical activity was associated with poor glycaemic control, a finding most clear in women and evident also in patients with no signs of diabetic complications. Furthermore, low physical activity was associated with a higher HbA1c variability, which in turn was associated with the progression of renal disease and CVD during follow-up. A higher level of physical activity was also associated with better insulin sensitivity. The prevalence of the metabolic syndrome in type 1 diabetes was also lower the higher the physical activity. The aerobic physical fitness level of young adults with type 1 diabetes was reduced compared with healthy peers and in men an association between higher fitness level and lower HbA1c was observed. In patients with type 1 diabetes, a higher physical activity was associated with better glycaemic control and may thus be beneficial with respect to the prevention of diabetic complications.

Contribution of different physical forces to the disjoining pressure of a thin water film being pressed by an oil droplet

With an objective to understand the nature of forces which contribute to the disjoining pressure of a thin water film on a steel substrate being pressed by an oil droplet, two independent sets of experiments were done. (i) A spherical silica probe approaches the three substrates; mica, PTFE and steel, in a 10 mM electrolyte solution at two different pHs (3 and 10). (ii) The silica probe with and without a smeared oil film approaches the same three substrates in water (pH = 6). The surface potential of the oil film/water was measured using a dynamic light scattering experiment. Assuming the capacity of a substrate for ion exchange the total interaction force for each experiment was estimated to include the Derjaguin-Landau-Verwey-Overbeek (DLVO) force, hydration repulsion, hydrophobic attraction and oil-capillary attraction. The best fit of these estimates to the force-displacement characteristics obtained from the two sets of experiment gives the appropriate surface potentials of the substrates. The procedure allows an assessment of the relevance of a specific physical interaction to an experimental configuration. Two of the principal observations of this work are: (i) The presence of a surface at constant charge, as in the presence of an oil film on the probe, significantly enhances the counterion density over what is achieved when both the surfaces allow ion exchange. This raises the corresponding repulsion barrier greatly. (ii) When the substrate surface is wettable by oil, oil-capillary attraction contributes substantially to the total interaction. If it is not wettable the oil film is deformed and squeezed out. (C) 2010 Elsevier Inc. All rights reserved.

The Physical Strenuousness of Work is Slightly Associated with an Upward Trend in the Body Mass Index

This paper explores the relationship between the physical strenuousness of work and the body mass index in Finland, using individual microdata over the period 1972-2002. The data contain self-reported information about the physical strenuousness of a respondent’s current occupation. Our estimates show that the changes in the physical strenuousness of work can explain around 8% at most of the definite increase in BMI observed over the period. The main reason for this appears to be that the quantitative magnitude of the effect of the physical strenuousness of work on BMI is rather moderate. Hence, according to the point estimates, BMI is only around 1.5% lower when one’s current occupation is physically very demanding and involves lifting and carrying heavy objects compared with sedentary job (reference group of the estimations), other things being equal. Accordingly, the changes in eating habits and the amount of physical activity during leisure time must be the most important contributors to the upward trend in BMI in industrialised countries, but not the changes in the labour market structure.

Novel Nanocomposites Made of Boron Nitride Nanotubes and a Physical Gel

This article describes successful incorporation of multiwalled boron nitride nanotubes (BNNTs) and various functionalized BNNTs by Lewis bases such as trioctylamine (TOA), tributylamine (TBA), and triphenylphosphine (TPP), etc., in organogels formed by triphenylenevinylene (TPV)-based low molecular weight gelator (LMWG) in toluene and consequent characterization of the resulting gel nanocomposites. Functionalized BNNTs were synthesized first,and the presence of tubular structures with high aspect ratio and increased diameter compared to the starting BNNTs was confirmed by SEM. TEM, and Raman spectroscopy. The micrographs of composites of I and BNNTs showed evidence of wrapping of the gelator molecules on to the BNNT surface presumably brought about by pi-pi stacking and van der Waals interactions, This leads to the formation of densely packed and directionally aligned fibrous networks. Such ``reinforced'' aggregation of the gelator molecules in presence of doped BNNTs led to an increase in the sot-to-gel transition temperature and the solidification temperature of the gel nanocomposites as revealed from differential scanning calorimetry. Rheological investigations of the gel nanocomposites indicate that the flow properties of the resulting materials become resistant to applied stress upon incorporation of even a very low wt % of BNNTs. Finally, the increase in thermal conductivity of the nanocomposite compared to the gelator alone was observed for the temperature range of 0-60 degrees C which may make these composites potentially useful in various applications depending on the choice and the amount of BNNT loading in the composite.

A physical mechanism for North Atlantic SST influence on the Indian summer monsoon

A link between the Atlantic Multidecadal Oscillation (AMO) and multidecadal variability of the Indian summer monsoon rainfall is unraveled and a long sought physical mechanism linking Atlantic climate and monsoon has been identified. The AMO produces persistent weakening (strengthening) of the meridional gradient of tropospheric temperature (TT) by setting up negative (positive) TT anomaly over Eurasia during northern late summer/autumn resulting in early (late) withdrawal of the south west monsoon and persistent decrease (increase) of seasonal monsoon rainfall. On inter-annual time scales, strong North Atlantic Oscillation (NAO) or North Annular mode (NAM) influences the monsoon by producing similar TT anomaly over Eurasia. The AMO achieves the interdecadal modulation of the monsoon by modulating the frequency of occurrence of strong NAO/NAM events. This mechanism also provides a basis for explaining the observed teleconnection between North Atlantic temperature and the Asian monsoon in paleoclimatic proxies. Citation: Goswami, B. N., M. S. Madhusoodanan, C. P. Neema, and D. Sengupta (2006), A physical mechanism for North Atlantic SST influence on the Indian summer monsoon

Physical Properties of Deep Drill Cores : Implications for Meteorite Impact Effects and Crustal Structures

Physical properties provide valuable information about the nature and behavior of rocks and minerals. The changes in rock physical properties generate petrophysical contrasts between various lithologies, for example, between shocked and unshocked rocks in meteorite impact structures or between various lithologies in the crust. These contrasts may cause distinct geophysical anomalies, which are often diagnostic to their primary cause (impact, tectonism, etc). This information is vital to understand the fundamental Earth processes, such as impact cratering and associated crustal deformations. However, most of the present day knowledge of changes in rock physical properties is limited due to a lack of petrophysical data of subsurface samples, especially for meteorite impact structures, since they are often buried under post-impact lithologies or eroded. In order to explore the uppermost crust, deep drillings are required. This dissertation is based on the deep drill core data from three impact structures: (i) the Bosumtwi impact structure (diameter 10.5 km, 1.07 Ma age; Ghana), (ii) the Chesapeake Bay impact structure (85 km, 35 Ma; Virginia, U.S.A.), and (iii) the Chicxulub impact structure (180 km, 65 Ma; Mexico). These drill cores have yielded all basic lithologies associated with impact craters such as post-impact lithologies, impact rocks including suevites and breccias, as well as fractured and unfractured target rocks. The fourth study case of this dissertation deals with the data of the Paleoproterozoic Outokumpu area (Finland), as a non-impact crustal case, where a deep drilling through an economically important ophiolite complex was carried out. The focus in all four cases was to combine results of basic petrophysical studies of relevant rocks of these crustal structures in order to identify and characterize various lithologies by their physical properties and, in this way, to provide new input data for geophysical modellings. Furthermore, the rock magnetic and paleomagnetic properties of three impact structures, combined with basic petrophysics, were used to acquire insight into the impact generated changes in rocks and their magnetic minerals, in order to better understand the influence of impact. The obtained petrophysical data outline the various lithologies and divide rocks into four domains. Based on target lithology the physical properties of the unshocked target rocks are controlled by mineral composition or fabric, particularly porosity in sedimentary rocks, while sediments result from diverse sedimentation and diagenesis processes. The impact rocks, such as breccias and suevites, strongly reflect the impact formation mechanism and are distinguishable from the other lithologies by their density, porosity and magnetic properties. The numerous shock features resulting from melting, brecciation and fracturing of the target rocks, can be seen in the changes of physical properties. These features include an increase in porosity and subsequent decrease in density in impact derived units, either an increase or a decrease in magnetic properties (depending on a specific case), as well as large heterogeneity in physical properties. In few cases a slight gradual downward decrease in porosity, as a shock-induced fracturing, was observed. Coupled with rock magnetic studies, the impact generated changes in magnetic fraction the shock-induced magnetic grain size reduction, hydrothermal- or melting-related magnetic mineral alteration, shock demagnetization and shock- or temperature-related remagnetization can be seen. The Outokumpu drill core shows varying velocities throughout the drill core depending on the microcracking and sample conditions. This is similar to observations by Kern et al., (2009), who also reported the velocity dependence on anisotropy. The physical properties are also used to explain the distinct crustal reflectors as observed in seismic reflection studies in the Outokumpu area. According to the seismic velocity data, the interfaces between the diopside-tremolite skarn layer and either serpentinite, mica schist or black schist are causing the strong seismic reflectivities.

The physical properties of SnS films grown on lattice-matched and amorphous substrates

The development of high-quality tin monosulphide (SnS) layers is one of the crucial tasks in the fabrication of efficient SnS-based optoelectronic devices. Reduction of strain between film and the substrate by using an appropriate lattice-matched (LM) substrate is a new attempt for the growth of high-quality layers. In this view, the SnS films were deposited on LM Al substrate using the thermal evaporation technique with a low rate of evaporation. The as-grown SnS films were characterized using appropriate techniques and the obtained results are discussed by comparing them with the properties of SnS films grown on amorphous substrate under the same conditions. From structural analysis of the films, it is noticed that the SnS films deposited on amorphous substrate have crystallites that were oriented along different directions. However, the SnS crystallites grown on Al substrate exhibited epitaxial growth along the 101] direction. Photoluminescence (PL) and Raman studies reveal that the films grown on Al substrate have better optical properties than those of the films grown on amorphous substrates. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Solubility and physical stability improvement of natiral xanthine derivatives

Use of natural xanthine derivates in medicine is complicated with their physical properties. Theobromine is poorly soluble while theophylline is highly sensitive to hydration. The aim of this study was to improve bioavailability of xanthines by co-crystallization, theophylline was also cocrystallized with carboxylic acids (capric, citric, glutaric, malenic, malonic, oxalic, stearic, succinic) and HPMC. Co-crystallization was performed by slow evaporation and ball milling. Physical stability was checked by wet granulation and water sorption methods, solubility was measured by intrinsic tablet dissolution. Theobromine formed co-crystal with other xanthines and theophylline interacted with all acids except stearic and HPMC, the latter showed alternative interactions based on hydrogen bonding. Hydration resistance was good in theophylline:succinic acid co-crystal and excellent in complexes containing capric, stearic acids and HPMC. Theophylline:HPMC showed improved solubility. The reported approach can promote use of xanthines and can be recommended for other compounds with similar problems.

Physical mapping of the genomic DNA of the Oryctes rhinoceros baculovirus, KI

A non-occluded baculovirus, OBV-KI has been isolated from the insect pest, Oryctes rhinoceros. The viral genome is estimated to be 123 kb, with a G + C content of 43 mol% and no detectible methylated bases. A restriction map of the OBV-KI genome for BamHI, EcoRI, HindIII, PstI, SalI and XbaI has been constructed.

Experimental analysis of thermo-physical processes in acoustically levitated heated droplets

An experimental setup using radiative heating has been used to understand the thermo-physical phenomena and chemical transformations inside acoustically levitated cerium nitrate precursor droplets. In this transformation process, through infrared thermography and high speed imaging, events such as vaporization, precipitation and chemical reaction have been recorded at high temporal resolution, leading to nanoceria formation with a porous morphology. The cerium nitrate droplet undergoes phase and shape changes throughout the vaporization process. Four distinct stages were delineated during the entire vaporization process namely pure evaporation, evaporation with precipitate formation, chemical reaction with phase change and formation of final porous precipitate. The composition was examined using scanning and transmission electron microscopy that revealed nanostructures and confirmed highly porous morphology with trapped gas pockets. Transmission electron microscopy (TEM) and high speed imaging of the final precipitate revealed the presence of trapped gases in the form of bubbles. TEM also showed the presence of nanoceria crystalline structures at 70 degrees C. The current study also looked into the effect of different heating powers on the process. At higher power, each phase is sustained for smaller duration and higher maximum temperature. In addition, the porosity of the final precipitate increased with power. A non-dimensional time scale is proposed to correlate the effect of laser intensity and vaporization rate of the solvent (water). The effect of acoustic levitation was also studied. Due to acoustic streaming, the solute selectively gets transported to the bottom portion of the droplet due to strong circulation, providing it rigidity and allows it become bowl shaped. (C) 2010 Elsevier Ltd. All rights reserved.

Leisure-time physical activity, health related functioning and retirement : a prospective cohort study among middle-aged employees

Physical inactivity has become a major threat to public health worldwide. The Finnish health and welfare policies emphasize that the working population should maintain good health and functioning until their normal retirement age and remain in good health and independence later in life. Health behaviours like physical activity potentially play an important role in reaching this target as physical activity contributes to better physical fitness and to reduced risk of major chronic diseases. The aim of this study was to examine first whether the volume and intensity of leisure-time physical activity impacts on subsequent physical health functioning, sickness absence and disability retirement. The second aim was to examine changes in leisure-time physical activity of moderate and vigorous intensity after transition to retirement. This study is part of the ongoing Helsinki Health Study. The baseline data were collected by questionnaires in 2000 - 02 among the employees of the City of Helsinki aged 40 to 60. The follow-up survey data were collected in 2007. Data on sickness absence were obtained from the employer s (City of Helsinki) sickness absence registers and pension data were obtained from the Finnish Centre for Pensions. Leisure-time physical activity was measured in four grades of intensity and classified according to physical activity recommendations considering both the volume and intensity of physical activity. Statistical techniques including analysis of covariance, logistic regression, Cox proportional hazards models and Poisson regression were used. Employees who were vigorously active during leisure time especially had better physical health functioning than those physically inactive. High physical activity in particular contributed to the maintenance of good physical health functioning. High physical activity also reduced the risk of subsequent sickness absences as well as the risk of all-cause disability retirement and retirement due to musculoskeletal and mental causes. Among those transferred to old-age retirement moderate-intensity leisure-time physical activity increased on average by more than half an hour per week and in addition the occurrence of physical inactivity reduced. Such changes were not observed among those remained employed and those transferred to disability retirement. This prospective cohort study provided novel results on the effects of leisure-time physical activity on health related functioning and changes in leisure-time physical activity after retirement. Although the benefits of moderate-intensity physical activity for health are well known these results suggest the importance of vigorous physical activity for subsequent health related functioning. Thus vigorous physical activity to enhance fitness should be given more emphasis from a public health perspective. In addition, physical activity should be encouraged among those who are about to retire.