Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Aplicação de tensoativos não iônicos na recuperação de fluidos de perfuração poliméricos

The drilling fluid used to assist in the drilling operation of oil wells, accumulates solids inherent in the formation as it is circulated in the well, interfering in the fluid performance during operation. It is discarded after use. The disposal of these fluids causes one of the most difficult environmental problems in the world. This study aims to promote liquid phase separation of drilling fluids, which have circulated in oil wells, and enable this recovered liquid to formulate a new fluid. For this, non-ionic surfactants were used in order to select the best outcome in phase separation. Five real water-based drilling fluids were utilized, which were collected directly from the fields of drilling oil wells, classified as polymeric fluids. The methodology used consisted in combining the fluid with surfactant and then subjecting it to a process of centrifugation or decantation. The decantating tests were scheduled through experimental planning 23 and 32, using as variables the percentage (%) of surfactant utilized and the stirring time in minutes. The surfactants used were ethoxylated nonylphenol and lauryl alcohol ethoxylated with different degrees of ethoxylation. Phase separation was monitored first by tests of stability, and subsequently by the height of the interface in beakers of 100 mL. The results showed that from the surfactants studied, the lauryl alcohol ethoxylated with 3 ethoxylation units has been the most effective in the phase separation process of the drilling fluids tested. The statistical tool used was of great industrial value regarding the programming phase separation in drilling fluids. In conclusion, the liquid phase separated using surfactant can be reused for a new formulation of drilling fluid with similar properties of a new fluid, assuring its efficiency. And in the resulting analysis it is also suggested that the adsorption is the mechanism that leads the phase separation, with surfactant adsorbing in the active solids

On determining spectral parameters, tracking jitter, and GPS positioning improvement by scintillation mitigation

A method of determining spectral parameters p (slope of the phase PSD) and T (phase PSD at 1 Hz) and hence tracking error variance in a GPS receiver PLL from just amplitude and phase scintillation indices and an estimated value of the Fresnel frequency has been previously presented. Here this method is validated using 50 Hz GPS phase and amplitude data from high latitude receivers in northern Norway and Svalbard. This has been done both using (1) a Fresnel frequency estimated using the amplitude PSD (in order to check the accuracy of the method) and (2) a constant assumed value of Fresnel frequency for the data set, convenient for the situation when contemporaneous phase PSDs are not available. Both of the spectral parameters (p, T) calculated using this method are in quite good agreement with those obtained by direct measurements of the phase spectrum as are tracking jitter variances determined for GPS receiver PLLs using these values. For the Svalbard data set, a significant difference in the scintillation level observed on the paths from different satellites received simultaneously was noted. Then, it is shown that the accuracy of relative GPS positioning can be improved by use of the tracking jitter variance in weighting the measurements from each satellite used in the positioning estimation. This has significant advantages for scintillation mitigation, particularly since the method can be accomplished utilizing only time domain measurements thus obviating the need for the phase PSDs in order to extract the spectral parameters required for tracking jitter determination.

Thermoplastic starch/natural rubber blends

Thermoplastic starch/natural rubber polymer blends were prepared using directly natural latex and cornstarch. The blends were prepared in an intensive batch mixer at 150 degreesC, with natural rubber content varying from 2.5 to 20%. The blends were characterised by mechanical analysis (stress-strain) and by scanning electron microscopy. The results revealed a reduction in the modulus and in tensile strength, becoming the blends less brittle than thermoplastic starch alone. Phase separation was observed in some compositions and was dependent on rubber and on plasticiser content (glycerol). Increasing plasticiser content made possible the addition of higher amounts of rubber. The addition of rubber was, however, limited by phase separation the appearance of which depended on the glycerol content. Scanning electron microscopy showed a good dispersion of the natural rubber in the continuos phase of thermoplastic starch matrix. (C) 2003 Elsevier B.V. Ltd. All rights reserved.

On the incorporation of the non-steroidal anti-inflammatory naproxen into cationic O/W microemulsions

Microemulsions (ME) containing hexadecyltrimethylammonium bromide (HTAB)/ethanol as surfactant, isopropylmyristate (IM) or butylstearate (BS) as oil phase and aqueous buffer were studied. Pseudo-ternary phase diagrams of the investigated systems were obtained at constant surfactant/cosurfactant molar ratio (1:5) by titration in order to characterize the proportions between the components to obtain clear systems. Oil in water microemulsions were prepared in a wide range of phase volume (phi). UV-vis absorption spectra of naproxen at pH 5.5 showed that the solubility of Np increases significantly in the presence of O/W ME in high phase volumes. For both, IM and BS microemulsions, the dynamic light scattering experiments showed that the size of the oil droplets remains constant in low values of phi, increasing abruptly in high phi values. Phase solubility study revealed that for both IM and BS microemulsions, the drug incorporation followed a straight-line profile in all range of phi. The data could be analyzed through the phase-separation model and the association constants (K) calculated varied from 27 to 90 M-1, depending on the pH and on the microemulsion oil phase. (c) 2005 Elsevier B.V. All rights reserved.

Effect of vesicles of dimethyldioctadecylammonium chloride and phospholipids on the rate of decarboxylation of 6-nitrobenzisoxazole-3-carboxylate

Sonicated mixtures of dimethyldioctadecylammonium chloride (DODAC), egg phosphatidylcholine (PC), dimyristoyl phosphatidylcholine (DMPC), and dipalmitoyl phosphatidylcholine (DPPC) were used to analyze vesicle effects on the rate of decarboxylation of 6-nitrobenzisoxazol-3-carboxylic acid (Nboc). Electron microscopic images of the vesicles were obtained with trehalose, a know cryoprotector. Phase diagrams and phase transitions temperatures of the vesicle bilayers were determined. Nboc decarboxylation rates increased in the presence of vesicles prepared with both phospholipids and DODAC/phospholipid mixtures. Quantitative analysis of vesicular effects was done using pseudophase models. Phospholipids catalyzed up to 140-fold while the maximum catalysis by DODAC/lipid vesicles reached 800-fold. Acceleration depends on alkyl chain length, fatty acid insaturation of the lipids, and the DODAC/phospholipid molar ratio. Catalysis is not related to the liquid crystalline-gel state of the bilayer and may be related to the relative position of Nboc with respect to the interface.

Ribotyping and virulence markers of Yersinia pseudotuberculosis strains isolated from animals in Brazil

Ribotyping and virulence markers has been used to investigate 68 Yersinia pseudotuberculosis strains of serogroups O:1a and O:3. The strains were isolated from clinical material obtained from healthy and sick animals in the Southern region of Brazil. Ribotypes were identified by double digestion of extracted DNA with the restriction endonucleases SmaI and PstI, separation by electrophoresis and hybridization with a digoxigenin-labeled cDNA probe. The presence of the chromosomal virulence marker genes inv, irp1, irp2, psn, ybtE, ybtP-ybtQ, and ybtX-ybtS, of the IS100 insertion sequence, and of the plasmid gene lcrF was detected by polymerase chain reaction. The strains were grouped into four distinct ribotypes, all of them comprising several strains. Ribotypes 1 and 4 presented distinct profiles, with 57.3% genetic similarity, ribotypes 2 and 3 presented 52.5% genetic similarity, and genetic similarity was 45% between these two groups (1/4 and 2/3). All strains possessed the inv, irp1, and irp2 genes. Additionally, strains of serogroup O:1a carried psn, ybtE, ybtP-ybtQ, ybtX-ybtS, and IS100. As expected lcrF was only detected in strains harboring the virulence plasmid. These data demonstrate the presence of Y. pseudotuberculosis strains harboring genotypic virulence markers in the livestock from Southern Brazil and that the dissemination of these bacteria may occur between herds.

A modified Primal-Dual Logarithmic-Barrier Method for solving the Optimal Power Flow problem with discrete and continuous control variables

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Alternative Model of Three-Phase Transmission Line Theory-Based Modal Decomposition

In this paper is shown the development of a transmission line, based on discrete circuit elements that provide responses directly in the time domain and phase. This model is valid for ideally transposed rows represent the phases of each of the small line segments are separated in their modes of propagation and the voltage and current are calculated at the modal field. However, the conversion phase-mode-phase is inserted in the state equations which describe the currents and voltages along the line of which there is no need to know the user of the model representation of the theory in the field lines modal.

Partículas inteligentes de poli (nisopropilacrilamida), quitosana e poli (ácido acrílico): efeito da temperatura e do pH sobre suas propriedades em suspensões aquosas

The present study describes the stability and rheological behavior of suspensions of poly (N-isopropylacrylamide) (PNIPAM), poly (N-isopropylacrylamide)-chitosan (PNIPAMCS), and poly (N-isopropylacrylamide)-chitosan-poly (acrylic acid) (PNIPAM-CS-PAA) crosslinked particles sensitive to pH and temperature. These dual-sensitive materials were simply obtained by one-pot method, via free-radical precipitation copolymerization with potassium persulfate, using N,N -methylenebisacrylamide (MBA) as a crosslinking agent. Incorporation of the precursor materials into the chemical networks was confirmed by elementary analysis and infrared spectroscopy. The influence of external stimuli such as pH and temperature, or both, on particle behavior was investigated through rheological measurements, visual stability tests and analytical centrifugation. The PNIPAM-CS particles showed higher stability in acid and neutral media, whereas PNIPAM-CS-PAA particles were more stable in neutral and alkaline media, both below and above the LCST of poly (Nisopropylacrylamide) (stability data). This is due to different interparticle interactions, as well as those between the particles and the medium (also evidenced by rheological data), which were also influenced by the pH and temperature of the medium. Based on the results obtained, we found that the introduction of pH-sensitive polymers to crosslinked poly (Nisopropylacrylamide) particles not only produced dual-sensitive materials, but allowed particle stability to be adjusted, making phase separation faster or slower, depending on the desired application. Thus, it is possible to adapt the material to different media

Markers of uremia and pericardial effusion in peritoneal dialysis

Inadequate dialysis causes accumulation of toxic residues that may lead to the development of dialysis-associated pericardial effusion, but several other factors could be associated with this abnormality. The purpose of this study was to evaluate clinical risk factors to asymptomatic pericardial effusion in peritoneal dialysis.This cross-sectional study included 34 patients aged a parts per thousand yen18 years on peritoneal dialysis for at least 3 months, who showed no symptomatic pericardial effusion, hepatic cirrhosis, neoplasias, lupus or amputations, none in minoxidil use. Asymptomatic pericardial effusion was diagnosed by echocardiography. Risk factors were evaluated by logistic regression and Roc curve. Significance level was set at P < 0.05.Patient age was 51 +/- A 15.9 years. of the 34 patients enrolled, 16 were men and 11 diabetic. Five of them presented pericardial effusion. Logistic regression identifies low hemoglobin level (RR 0.454 CI 95%: 0.225-0.913; P = 0.027), low phase angle (RR 0.236 CI 95%: 0.057-0.984; P = 0.048) and low Kt/V (RR 0.001 CI 95%: 0.0-0.492; P = 0.03) as risk factors to pericardial effusion. Roc curve showed that hemoglobin levels below 12.2 g/dL, Kt/V lower than 1.9 and phase angle lower than 4.5A degrees were the best cutoffs to predict pericardial effusion. Four patients showed these three parameters in the unfavorable range, and all these four patients presented pericardial effusion. The other patient with pericardial effusion had two of these parameters reduced.These findings corroborate the hypothesis that uremia plays a significant role in the pathogenesis of dialysis-associated pericardial effusion.

Associations between nutritional markers and inflammation in hemodialysis patients

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Identificação e comparação entre controle preditivo com modelo não linear e PI sintonizados com PSO em sistema de separação gravitacional de águia-óleo

The separation methods are reduced applications as a result of the operational costs, the low output and the long time to separate the uids. But, these treatment methods are important because of the need for extraction of unwanted contaminants in the oil production. The water and the concentration of oil in water should be minimal (around 40 to 20 ppm) in order to take it to the sea. Because of the need of primary treatment, the objective of this project is to study and implement algorithms for identification of polynomial NARX (Nonlinear Auto-Regressive with Exogenous Input) models in closed loop, implement a structural identification, and compare strategies using PI control and updated on-line NARX predictive models on a combination of three-phase separator in series with three hydro cyclones batteries. The main goal of this project is to: obtain an optimized process of phase separation that will regulate the system, even in the presence of oil gushes; Show that it is possible to get optimized tunings for controllers analyzing the mesh as a whole, and evaluate and compare the strategies of PI and predictive control applied to the process. To accomplish these goals a simulator was used to represent the three phase separator and hydro cyclones. Algorithms were developed for system identification (NARX) using RLS(Recursive Least Square), along with methods for structure models detection. Predictive Control Algorithms were also implemented with NARX model updated on-line, and optimization algorithms using PSO (Particle Swarm Optimization). This project ends with a comparison of results obtained from the use of PI and predictive controllers (both with optimal state through the algorithm of cloud particles) in the simulated system. Thus, concluding that the performed optimizations make the system less sensitive to external perturbations and when optimized, the two controllers show similar results with the assessment of predictive control somewhat less sensitive to disturbances

Short- and long-term reproductive effects of prenatal and lactational growth restriction caused by maternal diabetes in male rats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effects of Gestational and Lactational Fenvalerate Exposure on Immune and Reproductive Systems of Male Rats

The aim of this study was to determine the consequent reproductive developmental and immunotoxic effects due to exposure to fenvalerate during pregnancy and lactation in male offspring of maternal-treated rats. Pregnant rats were treated daily by oral gavage with 40 or 80 mg/kg of fenvalerate or corn oil (vehicle, control), from d 12 of pregnancy to d 21 of lactation. Immune and reproductive developmental effects were assessed in male offspring at postnatal days (PND) 40 (peripuberty), 60 (postpuberty), and 90 (sexual maturity). Treatment with the higher dose (80 mg/kg) resulted in convulsive behavior, hyperexcitability, and mortality in 45% of the dams. Fenvalerate was detected in the fetus due to placental transfer, as well as in pups due to breast-milk ingestion, persisting in male offspring until PND 40 even though pesticide treatment was terminated on PND 20. However, fenvalerate did not produce marked alterations in age of testicular descent to the scrotum and prepucial separation, parameters indicative of puberty initiation. In contrast, at puberty, there was a reduction in testicular weight and sperm production in male offspring of maternal-treated rats. At adulthood, the sperm counts and fertility did not differ between control and treated groups. Testosterone levels were not changed at any time during reproductive development. Similarly, no apparent exposure-related effects were detected in the histological structures of the lymphohematopoietic system. Data indicate that fenvalerate, in this experimental model, interfered with initial development of the male reproductive system, but that these effects on sperm production or fertility did not persist into adulthood. There was no apparent evidence that fenvalerate altered testosterone levels or produced a disruption in male endocrine functions.