Unusual surface and edge morphologies, sp2 to sp3 hybridized transformation and electronic damage after Ar+ ion irradiation of few-layer graphene surfaces

Roughness and defects induced on few-layer graphene (FLG) irradiated by Ar+ ions at different energies were investigated using X-ray photoemission spectroscopy (XPS) and atomic force microscopy techniques. The results provide direct experimental evidence of ripple formation, sp2 to sp3 hybridized carbon transformation, electronic damage, Ar+ implantation, unusual defects and edge reconstructions in FLG, which depend on the irradiation energy. In addition, shadowing effects similar to those found in oblique-angle growth of thin films were seen. Reliable quantification of the transition from the sp2-bonding to sp3-hybridized state as a result of Ar+ ion irradiation is achieved from the deconvolution of the XPS C (1s) peak. Although the ion irradiation effect is demonstrated through the shape of the derivative of the Auger transition C KVV spectra, we show that the D parameter values obtained from these spectra which are normally used in the literature fail to account for the sp2 to sp3 hybridization transition. In contrast to what is known, it is revealed that using ion irradiation at large FLG sample tilt angles can lead to edge reconstructions. Furthermore, FLG irradiation by low energy of 0.25 keV can be a plausible way of peeling graphene layers without the need of Joule heating reported previously

Spray pyrolysed In2S3 thin films: A potential electron selective layer for large area inverted bulk-heterojunction polymer solar cells

In this paper, we report the results of investigations on the potential of spray pyrolysis technique in depositing electron selective layer over larger area for the fabrication of inverted bulk-heterojunction polymer solar cells. The electron selective layer (In2S3) was deposited using spray pyrolysis technique and the linear heterojunction device thus fabricated exhibited good uniformity in photovoltaic properties throughout the area of the device. An MEH-PPV:PCBM inverted bulk-heterojunction device with In2S3 electron selective layer (active area of 3.25 3.25 cm2) was also fabricated and tested under indoor and outdoor conditions. Fromthe indoor measurements employing a tungsten halogen lamp (50mW/cm2 illumination), an opencircuit voltage of 0.41V and a short-circuit current of 5.6mA were obtained. On the other hand, the outdoor measurements under direct sunlight (74mW/cm2) yielded an open-circuit voltage of 0.46V and a short-circuit current of 9.37mA

Artificial boundary conditions for the Stokes and Navier-Stokes equations in domains that are layer-like at infinity

Artificial boundary conditions are presented to approximate solutions to Stokes- and Navier-Stokes problems in domains that are layer-like at infinity. Based on results about existence and asymptotics of the solutions v^infinity, p^infinity to the problems in the unbounded domain Omega the error v^infinity - v^R, p^infinity - p^R is estimated in H^1(Omega_R) and L^2(Omega_R), respectively. Here v^R, p^R are the approximating solutions on the truncated domain Omega_R, the parameter R controls the exhausting of Omega. The artificial boundary conditions involve the Steklov-Poincare operator on a circle together with its inverse and thus turn out to be a combination of local and nonlocal boundary operators. Depending on the asymptotic decay of the data of the problems, in the linear case the error vanishes of order O(R^{-N}), where N can be arbitrarily large.

Spechte als ökologische Indikatoren in Natur- und Wirtschaftswäldern im Bialowiera-Wald (Ostpolen)

Die vorliegende Untersuchung analysiert die Eignung der "Spechtgemeinschaft" als ökologische Indikatorengruppe und formuliert vor dem Hintergrund der Ergebnisse Forderungen und Empfehlungen für einen "spechtgerechten" Umgang mit Wäldern. Die Habitatnutzung von sieben Spechtarten beim Nahrungserwerb wurde über einen Zeitraum von zwei Jahren in urwaldartigen und forstlich genutzten Beständen verschiedener Waldgesellschaften systematisch beobachtet. Das Untersuchungsgebiet ist der Bialowieza-Wald im äußersten Osten Polens, wo in enger räumlicher Nachbarschaft Natur- und Wirtschaftswaldflächen bearbeitet werden konnten. Die Beobachtungen erfolgten zwischen Anfang März 1999 und Ende Februar 2001 und wurden zu allen Jahreszeiten durchgeführt. Vier der insgesamt sechs Probeflächen repräsentieren die wichtigste Laubwaldgesellschaft des Gebietes, das Tilio-Carpinetum, die übrigen zwei die wichtigste Nadelwaldgesellschaft, das Peucedano-Pinetum. Die Hälfte der zwischen 42 und 54 ha großen Probeflächen lag im streng geschützten Urwaldreservat des Bialowieza-Nationalparkes, die übrigen in forstlich genutzten Waldbeständen. Zusätzlich wurde ein 2,5 km langes Transekt durch bewirtschafteten Erlen-Eschen-Auenwald und sehr naturnahen Erlenbruch bearbeitet. Die Probeflächen wurden in ein Raster aus 50x50m großen Quadranten unterteilt. Zur Beobachtung der Spechte beim Nahrungserwerb erfolgten 21 Begehungen je Probefläche bzw. Transekt. Die Probeflächen wurden dazu auf parallelen Linien mit Abständen von je 100m begangen, Startpunkt und Startrichtung wurden variiert. Zur Charakterisierung der Vegetation und Bestandesstruktur erfolgten Erhebungen zur Baumartenzusammensetzung, Größenklassenverteilung der Bäume, Totholzanteil und Krautvegetation. 1332 Beobachtungen von Spechten beim Nahrungserwerb konnten ausgewertet werden. Der Buntspecht wurde in allen Flächen am häufigsten gesehen. Mittel-, Weißrücken- und Kleinspecht wurden überwiegend in den Tilio-Carpineten beobachtet, in den Naturwäldern häufiger als in den bewirtschafteten Beständen. Der Dreizehenspecht wurde im Nadelwald und stärker mit Fichten durchmischtem Laubwald angetroffen. Bei Schwarz- und Grauspecht konnte keine klare Vorliebe für bestimmte Waldgesellschaften ermittelt werden. Der Buntspecht ernährte sich vor allem im Herbst und Winter überwiegend von fetthaltigen Samen und wurde dann meist beim Bearbeiten von Fichten- oder Kiefernzapfen in Schmieden beobachtet. Der Mittelspecht suchte als "Sammelspecht" seine Nahrung vor allem an den Oberflächen der Stämme und Äste. Klein-, Weißrücken-, Dreizehen- und Schwarzspecht traten als Hackspechte in Erscheinung. Die wenigen Daten zum Grauspecht reichen nicht zur Ermittlung der bevorzugten Nahrungserwerbstechnik aus. Bei Bunt-, Mittel- und Weißrückenspecht konnte eine deutliche Vorliebe für die Stieleiche als Nahrungsbaum nachgewiesen werden. Der Dreizehenspecht ist jedoch die einzige der beobachteten Arten mit einer weitgehenden Spezialisierung auf eine bestimmte Baumart, er nutzte in allen Waldgesellschaften meist die Fichte. Insgesamt bevorzugten die Spechte Bäume mit großen Stammdurchmessern, beim Kleinspecht ist diese Vorliebe allerdings nur schwach ausgeprägt. Totholz wurde von Weißrücken-, Dreizehen- und Kleinspecht bei der Nahrungssuche bevorzugt, vom Mittelspecht jedoch nur gelegentlich genutzt. Beim Buntspecht zeigte der Totholz-Nutzungsanteil erhebliche Unterschiede zwischen verschiedenen Baumarten. Liegendes Totholz spielte in den Tilio-Carpineten im Vergleich zu stehendem Totholz und toten Teilen lebender Bäume nur eine geringe Rolle für Nahrung suchende Spechte.

Effect of market-driven minigrids on the frequency stabilization process of isolated middle-sized power grids

Neueste Entwicklungen in Technologien für dezentrale Energieversorgungsstrukturen, erneuerbare Energien, Großhandelsenergiemarkt, Mini- und Mikronetze, verteilte Intelligenz, sowie Informations- und Datenübertragungstechnologien werden die zukünftige Energiewelt maßgeblich bestimmen. Die derzeitigen Forschungsbemühungen zur Vernutzung aller dieser Technologien bilden die Voraussetzungen für ein zukünftiges, intelligentes Stromnetz. Dieses neue Konzept gründet sich auf die folgenden Säulen: Die Versorgung erfolgt durch dezentrale Erzeugungsanlagen und nicht mehr durch große zentrale Erzeuger; die Steuerung beeinflusst nicht mehr allein die Versorgung sondern ermöglich eine auch aktive Führung des Bedarf; die Eingabeparameter des Systems sind nicht mehr nur mechanische oder elektrische Kenngrößen sondern auch Preissignale; die erneuerbaren Energieträger sind nicht mehr nur angeschlossen, sondern voll ins Energienetz integriert. Die vorgelegte Arbeit fügt sich in dieses neue Konzept des intelligenten Stromnetz ein. Da das zukünftige Stromnetz dezentral konfiguriert sein wird, ist eine Übergangsphase notwendig. Dieser Übergang benötigt Technologien, die alle diese neue Konzepte in die derzeitigen Stromnetze integrieren können. Diese Arbeit beweist, dass ein Mininetz in einem Netzabschnitt mittlerer Größe als netzschützende Element wirken kann. Hierfür wurde ein neues Energiemanagementsystem für Mininetze – das CMS (englisch: Cluster Management System) – entwickelt. Diese CMS funktioniert als eine von ökonomischorientierte Betriebsoptimierung und wirkt wie eine intelligente Last auf das System ein, reagierend auf Preissignale. Sobald wird durch eine Frequenzsenkung eine Überlastung des Systems bemerkt, ändert das Mininetz sein Verhalten und regelt seine Belastung, um die Stabilisierung des Hauptnetzes zu unterstützen. Die Wirksamkeit und die Realisierbarkeit des einwickelten Konzept wurde mit Hilfe von Simulationen und erfolgreichen Laborversuchen bewiesen.

A Comparative Study on Internationalization and the Role of International Offices at Selected Middle Eastern and German Universities

Internationalization of higher education has become one of the most important policies for institutions of higher education worldwide. Though universities are international by nature, the need for intensified quality activities of international nature has promoted internationalization to be under spotlight of researchers, administrators and policy makers and to be an area for research. Each institution follows its certain way to govern its international affairs. Most Universities, especially in the 'Developed World' started to plan it strategically. This study explores the meanings and importance of internationalization especially that it means different things to different people. It also studies the rationales behind internationalizing higher education. It focuses on the four main prevailing rationales; political, cultural/social, economic/financial, and academic on both national and institutional levels. With the increasing need to strategically plan, the study explores internationalization strategies in terms of how to develop them, what are their approaches and types, and their components and dimensions. Damascus University has witnessed an overwhelming development of its international relations and activities. Therefore, it started to face a problem of how to deal with this increasing load especially that its International Office is the only unit that deals with the international issues. In order to study the internationalization phenomenon at Damascus University, the 2WH approach, which asks the what, why, and how questions, is used and in order to define the International Office's role in the internationalization process of the University, it studies it and the international offices of Kassel University, and Humboldt University in Germany, The University of Jordan, and Al Baath University in Syria using the 'SOCIAL' approach that studies and analyses the situation, organization, challenges, involvement, ambitions, and limitations of these offices. The internationalization process at the above-mentioned Universities is studied and compared in terms of its meaning, rationales for both the institution and its academic staff, challenges and strategic planning. Then a comparison is made among the international offices of the Universities to identify their approaches, what led to their success and what led to their failure in their practices. The aim is to provide Damascus University and its International Office with some good practices and, depending on the experiences of the professionals of the case-studies, a suggested guidance to the work of this Office and the University in general is given. The study uses the interviews with the different officials and stakeholders of the case-studies as the main method of collecting the information in addition to site visits, studying their official documents and their websites. The study belongs to qualitative research that has an action dimension in it since the recommendations will be applied in the International Office. The study concludes with few learned lessons for Damascus University and its International Office depending on the comparison that was done according to a set of dimensions. Finally a reflection on the relationship between internationalization of higher education and politics, the impact of politics on Middle Eastern Universities, and institutional internationalization strategies are presented.

Simultaneous Drying and Separation of Composite Agricultural Material for Hay Processing

In composite agricultural materials such as grass, tee, medicinal plants; leaves and stems have a different drying time. By this behavior, after leaving the dryer, the stems may have greater moisture content than desired, while the leaves one minor, which can cause either the appearance of fungi or the collapse of the over-dried material. Taking into account that a lot of grass is dehydrated in forced air dryers, especially rotary drum dryers, this research was developed in order to establish conditions enabling to make a separation of the components during the drying process in order to provide a homogeneous product at the end. For this, a rotary dryer consisting of three concentric cylinders and a circular sieve aligned with the more internal cylinder was proposed; so that, once material enters into the dryer in the area of the inner cylinder, stems pass through sieve to the middle and then continue towards the external cylinder, while the leaves continue by the inner cylinder. For this project, a mixture of Ryegrass and White Clover was used. The characteristics of the components of a mixture were: Drying Rate in thin layer and in rotation, Bulk density, Projected Area, Terminal velocity, weight/Area Ratio, Flux through Rotary sieve. Three drying temperatures; 40°C, 60° C and 80° C, and three rotation speeds; 10 rpm, 20 rpm and 40 rpm were evaluated. It was found that the differences in drying time are the less at 80 °C when the dryer rotates at 40 rpm. Above this speed, the material adheres to the walls of the dryer or sieve and does not flow. According to the measurements of terminal velocity of stems and leaves of the components of the mixture, the speed of the air should be less than 1.5 m s-1 in the inner drum for the leaves and less than 4.5 m s-1 in middle and outer drums for stems, in such way that only the rotational movement of the dryer moves the material and achieves a greater residence time. In other hand, the best rotary sieve separation efficiencies were achieved when the material is dry, but the results are good in all the moisture contents. The best rotary speed of sieve is within the critical rotational speed, i.e. 20 rpm. However, the rotational speed of the dryer, including the sieve in line with the inner cylinder should be 10 rpm or less in order to achieve the greatest residence times of the material inside the dryer and the best agitation through the use of lifting flights. With a finite element analysis of a dryer prototype, using an air flow allowing speeds of air already stated, I was found that the best performance occurs when, through a cover, air enters the dryer front of the Middle cylinder and when the inner cylinder is formed in its entirety through a sieve. This way, air flows in almost equal amounts by both the middle and external cylinders, while part of the air in the Middle cylinder passes through the sieve towards the inner cylinder. With this, leaves do not adhere to the sieve and flow along drier, thanks to the rotating movement of the drums and the showering caused by the lifting flights. In these conditions, the differences in drying time are reduced to 60 minutes, but the residence time is higher for the stems than for leaves, therefore the components of the mixture of grass run out of the dryer with the same desired moisture content.

Strained Silicon on Silicon by Wafer Bonding and Layer Transfer from Relaxed SiGe Buffer

We report the creation of strained silicon on silicon (SSOS) substrate technology. The method uses a relaxed SiGe buffer as a template for inducing tensile strain in a Si layer, which is then bonded to another Si handle wafer. The original Si wafer and the relaxed SiGe buffer are subsequently removed, thereby transferring a strained-Si layer directly to Si substrate without intermediate SiGe or oxide layers. Complete removal of Ge from the structure was confirmed by cross-sectional transmission electron microscopy as well as secondary ion mass spectrometry. A plan-view transmission electron microscopy study of the strained-Si/Si interface reveals that the lattice-mismatch between the layers is accommodated by an orthogonal array of edge dislocations. This misfit dislocation array, which forms upon bonding, is geometrically necessary and has an average spacing of approximately 40nm, in excellent agreement with established dislocation theory. To our knowledge, this is the first study of a chemically homogeneous, yet lattice-mismatched, interface.

Partial disjoint path for multi-layer protection in GMPLS networks

In this paper, different recovery methods applied at different network layers and time scales are used in order to enhance the network reliability. Each layer deploys its own fault management methods. However, current recovery methods are applied to only a specific layer. New protection schemes, based on the proposed partial disjoint path algorithm, are defined in order to avoid protection duplications in a multi-layer scenario. The new protection schemes also encompass shared segment backup computation and shared risk link group identification. A complete set of experiments proves the efficiency of the proposed methods in relation with previous ones, in terms of resources used to protect the network, the failure recovery time and the request rejection ratio

Enhanced multi-layer protection in multi-service GMPLS networks

This paper focuses on QoS routing with protection in an MPLS network over an optical layer. In this multi-layer scenario each layer deploys its own fault management methods. A partially protected optical layer is proposed and the rest of the network is protected at the MPLS layer. New protection schemes that avoid protection duplications are proposed. Moreover, this paper also introduces a new traffic classification based on the level of reliability. The failure impact is evaluated in terms of recovery time depending on the traffic class. The proposed schemes also include a novel variation of minimum interference routing and shared segment backup computation. A complete set of experiments proves that the proposed schemes are more efficient as compared to the previous ones, in terms of resources used to protect the network, failure impact and the request rejection ratio

Adobe Photoshop : Layer Basics

Find out more about Photoshop layers with this share of links and video tutorials.

Traducción de la sentencia de la Corte Internacional de Justicia relativa a la Soberanía sobre Pedra Branca/Pulau Batu Puteh, Middle Rocks y South Ledge (Malasia/Singapur) Decisión sobre el fondo

Traducción de la decisión de la CIJ

Traducción de la sentencia de la Corte Internacional de Justicia relativa a la Soberanía sobre Pedra Branca/Pulau Batu Puteh, Middle Rocks y South Ledge (Malasia/Singapur) Decisión sobre el fondo.

Ver Documento.