Quantification of free auxins in semi-hardwood plant cuttings and microshoots by dispersive liquid–liquid microextraction/microwave derivatization and GC/MS analysis

Several studies have suggested that differences in the natural rooting ability of plant cuttings could be attributed to differences in endogenous auxin levels. Hence, during rooting experiments, it is important to be able to routinely monitor the evolution of endogenous levels of plant hormones. This work reports the development of a new method for the quantification of free auxins in auxin-treated Olea europaea (L.) explants, using dispersive liquid–liquid microextraction (DLLME) and microwave assisted derivatization (MAD) followed by gas chromatography/mass spectrometry (GC/MS) analysis. Linear ranges of 0.5–500 ng mL 1 and 1–500 mg mL 1 were used for the quantification of indole-3-acetic acid (IAA) and indole-3-butyric acid (IBA), respectively. Determined by serial dilutions, the limits of detection (LOD) and quantification (LOQ) were 0.05 ng mL 1 and 0.25 ng mL 1, respectively for both compounds. When using the calibration curve for determination, the LOQ corresponded to 0.5 ng mL 1 (IAA) and 0.5 mg mL 1 (IBA). The proposed method proved to be substantially faster than other alternatives, and allowed free auxin quantification in real samples of semi-hardwood cuttings and microshoots of two olive cultivars. The concentrations found in the analyzed samples are in the range of 0.131–0.342 mg g 1 (IAA) and 20–264 mg g 1 (IBA).

My place through my eyes : a social constructionist approach to researching the relationships between socioeconomic living contexts and physical activity

There is a growing evidence-base in the epidemiological literature that demonstrates significant associations between people’s living circumstances – including their place of residence – and their health-related practices and outcomes (Leslie, 2005; Karpati, Bassett, & McCord, 2006; Monden, Van Lenthe, & Mackenbach, 2006; Parkes & Kearns, 2006; Cummins, Curtis, Diez-Roux, & Macintyre, 2007; Turrell, Kavanagh, Draper, & Subramanian, 2007). However, these findings raise questions about the ways in which living places, such as households and neighbourhoods, figure in the pathways connecting people and health (Frolich, Potvin, Chabot, & Corin, 2002; Giles-Corti, 2006; Brown et al, 2006; Diez Roux, 2007). This thesis addressed these questions via a mixed methods investigation of the patterns and processes connecting people, place, and their propensity to be physically active. Specifically, the research in this thesis examines a group of lower-socioeconomic residents who had recently relocated from poorer suburbs to a new urban village with a range of health-related resources. Importantly, the study contrasts their historical relationship with physical activity with their reactions to, and everyday practices in, a new urban setting designed to encourage pedestrian mobility and autonomy. The study applies a phenomenological approach to understanding living contexts based on Berger and Luckman’s (1966) conceptual framework in The Social Construction of Reality. This framework enables a questioning of the concept of context itself, and a treatment of it beyond environmental factors to the processes via which experiences and interactions are made meaningful. This approach makes reference to people’s histories, habituations, and dispositions in an exploration between social contexts and human behaviour. This framework for thinking about context is used to generate an empirical focus on the ways in which this residential group interacts with various living contexts over time to create a particular construction of physical activity in their lives. A methodological approach suited to this thinking was found in Charmaz’s (1996; 2001; 2006) adoption of a social constructionist approach to grounded theory. This approach enabled a focus on people’s own constructions and versions of their experiences through a rigorous inductive method, which provided a systematic strategy for identifying patterns in the data. The findings of the study point to factors such as ‘childhood abuse and neglect’, ‘early homelessness’, ‘fear and mistrust’, ‘staying indoors and keeping to yourself’, ‘conflict and violence’, and ‘feeling fat and ugly’ as contributors to an ongoing core category of ‘identity management’, which mediates the relationship between participants’ living contexts and their physical activity levels. It identifies barriers at the individual, neighbourhood, and broader ecological levels that prevent this residential group from being more physically active, and which contribute to the ways in which they think about, or conceptualise, this health-related behaviour in relationship to their identity and sense of place – both geographic and societal. The challenges of living well and staying active in poorer neighbourhoods and in places where poverty is concentrated were highlighted in detail by participants. Participants’ reactions to the new urban neighbourhood, and the depth of their engagement with the resources present, are revealed in the context of their previous life-experiences with both living places and physical activity. Moreover, an understanding of context as participants’ psychological constructions of various social and living situations based on prior experience, attitudes, and beliefs was formulated with implications for how the relationship between socioeconomic contextual effects on health are studied in the future. More detailed findings are presented in three published papers with implications for health promotion, urban design, and health inequalities research. This thesis makes a substantive, conceptual, and methodological contribution to future research efforts interested in how physical activity is conceptualised and constructed within lower socioeconomic living contexts, and why this is. The data that was collected and analysed for this PhD generates knowledge about the psychosocial processes and mechanisms behind the patterns observed in epidemiological research regarding socioeconomic health inequalities. Further, it highlights the ways in which lower socioeconomic living contexts tend to shape dispositions, attitudes, and lifestyles, ultimately resulting in worse health and life chances for those who occupy them.

Effects and feasibility of a multi-disciplinary orientation program for newly registered cancer patients : design of a randomised controlled trial

Background Diagnosis and treatment of cancer can contribute to psychological distress and anxiety amongst patients. Evidence indicates that information giving can be beneficial in reducing patient anxiety, so oncology specific information may have a major impact on this patient group. This study investigates the effects of an orientation program on levels of anxiety and self-efficacy amongst newly registered cancer patients who are about to undergo chemotherapy and/or radiation therapy in the cancer care centre of a large tertiary Australian hospital. Methods The concept of interventions for orienting new cancer patients needs revisiting due to the dynamic health care system. Historically, most orientation programs at this cancer centre were conducted by one nurse. A randomised controlled trial has been designed to test the effectiveness of an orientation program with bundled interventions; a face-to-face program which includes introduction to the hospital facilities, introduction to the multi-disciplinary team and an overview of treatment side effects and self care strategies. The aim is to orientate patients to the cancer centre and to meet the health care team. We hypothesize that patients who receive this orientation will experience lower levels of anxiety and distress, and a higher level of self-efficacy. Discussion An orientation program is a common health care service provided by cancer care centres for new cancer patients. Such programs aim to give information to patients at the beginning of their encounter at a cancer care centre. It is clear in the literature that interventions that aim to improve self-efficacy in patients may demonstrate potential improvement in health outcomes. Yet, evidence on the effects of orientation programs for cancer patients on self-efficacy remains scarce, particularly with respect to the use of multidisciplinary team members. This paper presents the design of a randomised controlled trial that will evaluate the effects and feasibility of a multidisciplinary orientation program for new cancer patients.

Socioeconomic differences in takeaway food consumption and their contribution to inequalities in dietary intakes

Background Takeaway consumption has been increasing and may contribute to socioeconomic inequalities in overweight/obesity and chronic disease. This study examined socioeconomic differences in takeaway consumption patterns, and their contributions to dietary intake inequalities. Method Cross-sectional dietary intake data from adults aged between 25 and 64 years from the Australian National Nutrition Survey (n= 7319, 61% response rate). Twenty-four hour dietary recalls ascertained intakes of takeaway food, nutrients and fruit and vegetables. Education was used as socioeconomic indicator. Data were analysed using logistic regression and general linear models. Results Thirty-two percent (n = 2327) consumed takeaway foods in the 24 hour period. Lower-educated participants were less likely than their higher-educated counterparts to have consumed total takeaway foods (OR 0.64; 95% CI 0.52, 0.80). Of those consuming takeaway foods, the lowest-educated group was more likely to have consumed “less healthy” takeaway choices (OR 2.55; 95% CI 1.73, 3.77), and less likely to have consumed “healthy” choices (OR 0.52; 95% CI 0.36, 0.75). Takeaway foods made a greater contribution to energy, total fat, saturated fat, and fibre intakes among lower than higher-educated groups. Lower likelihood of fruit and vegetable intakes were observed among “less healthy” takeaway consumers, whereas a greater likelihood of their consumption was found among “healthy” takeaway consumers. Conclusions Total and the types of takeaway foods consumed may contribute to socioeconomic inequalities in intakes of energy, total and saturated fats. However, takeaway consumption is unlikely to be a factor contributing to the lower fruit and vegetable intakes among socioeconomically-disadvantaged groups.

The influence of national culture on communication practices : a case study on Malaysian organisation

National culture is deeply rooted in values, which are learned and acquired when we are young (2007, p. 6), and „embedded deeply in everyday life. (Newman & Nollen, 1996, p. 754). Values have helped to shape us into who we are today. In other words, as we grow older, the cultural values we have learned and adapted to will mould our daily practices. This is reflected in our actions, behaviours, and the ways in which we communicate. Based on the previous assertion, it can be suggested that national culture may also influence organisational culture, as our „behaviour at work is a continuation of behaviour learned earlier. (Hofstede, 1991, p. 4). Cultural influence in an organisation could be evidenced by looking at communication practices: how employees interact with one another as they communicate in their daily practices. Earlier studies in organisational communication see communication as the heart of an organisation in which it serves, and as „the essence of organised activity and the basic process out of which all other functions derive. (Bavelas and Barret, cited in Redding, 1985, p. 7). Hence, understanding how culture influences communication will help with understanding organisational behaviour. This study was conducted to look at how culture values, which are referred to as culture dimensions in this thesis, influenced communication practices in an organisation that was going through a change process. A single case study was held in a Malaysian organisation, to investigate how Malaysian culture dimensions of respect, collectivism, and harmony were evidenced in the communication practices. Data was collected from twelve semi-structured interviews and five observation sessions. Guided by six attributes identified in the literature, (1) acknowledging seniority, knowledge and experience, 2) saving face, 3) showing loyalty to organisation and leaders, 4) demonstrating cohesiveness among members, 5) prioritising group interests over personal interests, and 6) avoiding confrontations of Malaysian culture dimensions, this study found eighteen communication practices performed by employees of the organisation. This research contributes to the previous cultural work, especially in the Malaysian context, in which evidence of Malaysian culture dimensions of respect, collectivism, and harmony were displayed in communication practices: 1) acknowledging the status quo, 2) obeying orders and directions, 3) name dropping, 4) keeping silent, 5) avoiding questioning, 6) having separate conversations, 7) adding, not criticising, 8) sugar coating, 9) instilling a sense of belonging, 10) taking sides, 11) cooperating, 12) sacrificing personal interest, 13) protecting identity, 14) negotiating, 15) saying „yes. instead of „no., 16) giving politically correct answers, 17) apologising, and 18) tolerating errors. Insights from this finding will help us to understand the organisational challenges that rely on communication, such as during organisational change. Therefore, data findings will be relevant to practitioners to understand the impact of culture on communication practices across countries.

Patterns of engagement in workplace learning amongst employees from social sectors

Continuous learning and development has become increasingly important in the information age. However, employees with limited formal education in lower status occupations may be disadvantaged in their opportunities for development, as their jobs tend to require more limited knowledge and skills. In mature age, such workers may be subject to cumulative disadvantage with respect to work related learning and development, as well as negative stereotyping. This thesis concerns work related learning and development from a lifespan development psychology perspective. Development across the lifespan is grounded in biocultural co-constructivism. That is, the reciprocal influences of the individual and environment produce change in the individual. Existing theories and models of adaptive development attempt to explain how developmental resources are allocated across the lifespan. These included the Meta- theory of Selective Optimisation with Compensation, Dual Process Model of Self Regulation, and Developmental Regulation via Optimisation and Primary and Secondary Control. These models were integrated to create the Model of Adaptive Development for Work Related Learning. The Learning and Development Survey (LDS) was constructed to measure the hypothesised processes of adaptive development for work related learning, which were individual goal selection, individual goal engagement, individual goal disengagement, organisational opportunities (selection and engagement), and organisational constraints. Data collection was undertaken in two phases: the pilot study and the main study. The objective of the pilot study was to test the LDS on a target population of 112 employees from a local government organisation. Exploratory factor analysis reduced the pilot version of the survey to 38 items encompassing eight constructs which covered the processes of the model of adaptive development for work related learning. In the main study, the Revised Learning and Development Survey (R-LDS) was administered to another group of 137 employees from the local government organisation, as well as 110 employees from a private healthcare organisation. The purpose of the main study was to validate the R-LDS on two different groups to provide evidence of stability, and compare survey scores according to age and occupational status to determine construct validity. Findings from the main study indicated that only four constructs of the R-LDS were stable, which were organisational opportunities – selection, individual goal engagement, organisational constraints – disengagement and organisational opportunities – engagement. In addition, MANOVA studies revealed that the demographic variables affected organisational opportunities and constraints in the workplace, although individual goal engagement was not influenced by age. The findings from the pilot and main study partially supported the model of adaptive development for work related learning. Given that only four factors displayed adequate reliability in terms of internal consistency and stability, the findings suggest that individual goal selection and individual goal disengagement are less relevant to work related learning and development. Some recent research which emerged during the course of the current study has suggested that individual goal selection and individual goal disengagement are more relevant when goal achievement is impeded by biological constraints such as ageing. However, correlations between the retained factors support the model of adaptive development for work related learning, and represent the role of biocultural co-constructivism in development. Individual goal engagement was positively correlated with both opportunity factors (selection and engagement), while organisational constraints – disengagement was negatively correlated with organisational opportunities – selection. Demographic findings indicated that higher occupational status was associated with more opportunities for development. Age was associated with fewer opportunities or greater constraints for development, especially for lower status workers.

From Sydney and Shanghai : Australian and Chinese women writing modernism

In the 1930s and 1940s, Australian women writers published novels, poems, and short stories that pushed the boundaries of their national literary culture. From their position in the Pacific, they entered into a dialogue with a European modernism that they reworked to invigorate their own writing and to make cross-continental connections. My interest in the work of Australian women prose writers of this period stems from an appreciation of the extent of their engagement with interwar modernism (an engagement that is generally under-acknowledged) and the realization that there are commonalities of approach with the ways in which contemporaneous Chinese authors negotiated this transnational cultural traffic. China and Australia, it has been argued, share an imaginative and literal association of many centuries, and this psychic history produces a situation in which ‘Australians feel drawn towards China: they cannot leave it alone.’1 Equally, Chinese exploration of the great southern land began in the fifteenth century, prior to European contact. In recent times, the intensity of Australia’s cultural and commercial connections with Asia has led to a repositioning of the Australian sense of regionalism in general and, in particular, has activated yet another stage in the history of its relationship with China. In this context, the association of Australian and Chinese writing is instructive because the commonalities of approach and areas of interest between certain authors indicate that Australian writers were not alone in either the content or style of their response to European modernism. This recognition, in turn, advances discussions of modernism in Australia and reveals an alternative way of looking at the world from the Pacific Rim through literature. The intent is to examine selective Australian and Chinese authors who are part of this continuous history and whose writing demonstrates common thematic and stylistic features via the vector of modernism. I focus on the 1930s and 1940s because these are the decades in which Australia and China experienced wideranging conflict in the Pacific, and it is significant that war, both forthcoming and actual, features as an ominous soundtrack in the writing of Chinese and Australian women. I argue that, given the immensity of cultural difference between Australia and China, there is an especially interesting juncture in the ways in which the authors interrogate modernist practices and the challenge of modernism. The process in which writing from the Pacific Rim jointly negotiates the twin desires of engaging with European literary form and representing one’s own culture may be seen as what Jessica Berman identifies as a geomodernism, one of the ‘new possible geographies’ of modernism.2 My discussion centres on the work of the Australian women, to which the Chinese material serves as a point of reference, albeit a critical one. The Chinese writing examined here is restricted to authors who wrote at least some material in English and whose work is available in translation.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Understanding parental physical activity : meanings, habits, and social role influence

Objectives: The research aimed to explore parents’ understandings of physical activity (PA), patterns of PA-related behaviour, and how constructions of social role expectations might influence their PA behaviour. Design and Method: Using a qualitative descriptive design and adopting a social constructionism approach to broaden interpretations of parents’ understandings, 40 adults (21 mothers, 19 fathers; aged 23 to 49 years) living in South East Queensland, Australia participated in semi-structured individual and group interviews. The interviews were analysed using thematic analysis. Results: Parents had clear understandings of what constitutes PA and engaged in various activities which were integrated with or independent of the children. Being active with children, however, was not always constructed favourably in which many parents described the difficulties of being active with their children. All individuals experienced changes in their PA behaviours after having children. For most, a decline in PA level, intensity, and structure was experienced; however, some did experience parenthood as a time to be active. A level of acceptance for the lack of activity performed was also expressed as were feelings of resentment and envy for those who maintained previous activity habits. Parenting and partner roles were considered most influential on PA-related behaviour and were constructed in ways that had both positive and negative influences on activity performance. Parents, however, were empowered to construct strategies to resolve conflicts between social role performance and being active. Conclusion: Results show that parents experience unique difficulties that intervention work should consider when designing programs aimed at increasing parental PA.

Anxiety among high school students in India : comparisons across gender, school type, social strata, and perceptions of quality time with parents

The broad objective of the study was to better understand anxiety among adolescents in Kolkata city, India. Specifically, the study compared anxiety across gender, school type, socio-economic background and mothers’ employment status. The study also examined adolescents’ perceptions of quality time with their parents. A group of 460 adolescents (220 boys and 240 girls), aged 13-17 years were recruited to participate in the study via a multi-stage sampling technique. The data were collected using a self-report semi-structured questionnaire and a standardized psychological test, the State-Trait Anxiety Inventory. Results show that anxiety was prevalent in the sample with 20.1% of boys and 17.9% of girls found to be suffering from high anxiety. More boys were anxious than girls (p<0.01). Adolescents from Bengali medium schools were more anxious than adolescents from English medium schools (p<0.01). Adolescents belonging to the middle class (middle socio-economic group) suffered more anxiety than those from both high and low socio-economic groups (p<0.01). Adolescents with working mothers were found to be more anxious (p<0.01). Results also show that a substantial proportion of the adolescents perceived they did not receive quality time from fathers (32.1%) and mothers (21.3%). A large number of them also did not feel comfortable to share their personal issues with their parents (60.0% for fathers and 40.0% for mothers).

A new multilevel converter configuration for high power and high quality applications

The Queensland University of Technology (QUT) allows the presentation of theses for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of ten published /submitted papers and book chapters of which nine have been published and one is under review. This project is financially supported by an Australian Research Council (ARC) Discovery Grant with the aim of investigating multilevel topologies for high quality and high power applications, with specific emphasis on renewable energy systems. The rapid evolution of renewable energy within the last several years has resulted in the design of efficient power converters suitable for medium and high-power applications such as wind turbine and photovoltaic (PV) systems. Today, the industrial trend is moving away from heavy and bulky passive components to power converter systems that use more and more semiconductor elements controlled by powerful processor systems. However, it is hard to connect the traditional converters to the high and medium voltage grids, as a single power switch cannot stand at high voltage. For these reasons, a new family of multilevel inverters has appeared as a solution for working with higher voltage levels. Besides this important feature, multilevel converters have the capability to generate stepped waveforms. Consequently, in comparison with conventional two-level inverters, they present lower switching losses, lower voltage stress across loads, lower electromagnetic interference (EMI) and higher quality output waveforms. These properties enable the connection of renewable energy sources directly to the grid without using expensive, bulky, heavy line transformers. Additionally, they minimize the size of the passive filter and increase the durability of electrical devices. However, multilevel converters have only been utilised in very particular applications, mainly due to the structural limitations, high cost and complexity of the multilevel converter system and control. New developments in the fields of power semiconductor switches and processors will favor the multilevel converters for many other fields of application. The main application for the multilevel converter presented in this work is the front-end power converter in renewable energy systems. Diode-clamped and cascade converters are the most common type of multilevel converters widely used in different renewable energy system applications. However, some drawbacks – such as capacitor voltage imbalance, number of components, and complexity of the control system – still exist, and these are investigated in the framework of this thesis. Various simulations using software simulation tools are undertaken and are used to study different cases. The feasibility of the developments is underlined with a series of experimental results. This thesis is divided into two main sections. The first section focuses on solving the capacitor voltage imbalance for a wide range of applications, and on decreasing the complexity of the control strategy on the inverter side. The idea of using sharing switches at the output structure of the DC-DC front-end converters is proposed to balance the series DC link capacitors. A new family of multioutput DC-DC converters is proposed for renewable energy systems connected to the DC link voltage of diode-clamped converters. The main objective of this type of converter is the sharing of the total output voltage into several series voltage levels using sharing switches. This solves the problems associated with capacitor voltage imbalance in diode-clamped multilevel converters. These converters adjust the variable and unregulated DC voltage generated by renewable energy systems (such as PV) to the desirable series multiple voltage levels at the inverter DC side. A multi-output boost (MOB) converter, with one inductor and series output voltage, is presented. This converter is suitable for renewable energy systems based on diode-clamped converters because it boosts the low output voltage and provides the series capacitor at the output side. A simple control strategy using cross voltage control with internal current loop is presented to obtain the desired voltage levels at the output voltage. The proposed topology and control strategy are validated by simulation and hardware results. Using the idea of voltage sharing switches, the circuit structure of different topologies of multi-output DC-DC converters – or multi-output voltage sharing (MOVS) converters – have been proposed. In order to verify the feasibility of this topology and its application, steady state and dynamic analyses have been carried out. Simulation and experiments using the proposed control strategy have verified the mathematical analysis. The second part of this thesis addresses the second problem of multilevel converters: the need to improve their quality with minimum cost and complexity. This is related to utilising asymmetrical multilevel topologies instead of conventional multilevel converters; this can increase the quality of output waveforms with a minimum number of components. It also allows for a reduction in the cost and complexity of systems while maintaining the same output quality, or for an increase in the quality while maintaining the same cost and complexity. Therefore, the asymmetrical configuration for two common types of multilevel converters – diode-clamped and cascade converters – is investigated. Also, as well as addressing the maximisation of the output voltage resolution, some technical issues – such as adjacent switching vectors – should be taken into account in asymmetrical multilevel configurations to keep the total harmonic distortion (THD) and switching losses to a minimum. Thus, the asymmetrical diode-clamped converter is proposed. An appropriate asymmetrical DC link arrangement is presented for four-level diode-clamped converters by keeping adjacent switching vectors. In this way, five-level inverter performance is achieved for the same level of complexity of the four-level inverter. Dealing with the capacitor voltage imbalance problem in asymmetrical diodeclamped converters has inspired the proposal for two different DC-DC topologies with a suitable control strategy. A Triple-Output Boost (TOB) converter and a Boost 3-Output Voltage Sharing (Boost-3OVS) converter connected to the four-level diode-clamped converter are proposed to arrange the proposed asymmetrical DC link for the high modulation indices and unity power factor. Cascade converters have shown their abilities and strengths in medium and high power applications. Using asymmetrical H-bridge inverters, more voltage levels can be generated in output voltage with the same number of components as the symmetrical converters. The concept of cascading multilevel H-bridge cells is used to propose a fifteen-level cascade inverter using a four-level H-bridge symmetrical diode-clamped converter, cascaded with classical two-level Hbridge inverters. A DC voltage ratio of cells is presented to obtain maximum voltage levels on output voltage, with adjacent switching vectors between all possible voltage levels; this can minimize the switching losses. This structure can save five isolated DC sources and twelve switches in comparison to conventional cascade converters with series two-level H bridge inverters. To increase the quality in presented hybrid topology with minimum number of components, a new cascade inverter is verified by cascading an asymmetrical four-level H-bridge diode-clamped inverter. An inverter with nineteen-level performance was achieved. This synthesizes more voltage levels with lower voltage and current THD, rather than using a symmetrical diode-clamped inverter with the same configuration and equivalent number of power components. Two different predictive current control methods for the switching states selection are proposed to minimise either losses or THD of voltage in hybrid converters. High voltage spikes at switching time in experimental results and investigation of a diode-clamped inverter structure raised another problem associated with high-level high voltage multilevel converters. Power switching components with fast switching, combined with hard switched-converters, produce high di/dt during turn off time. Thus, stray inductance of interconnections becomes an important issue and raises overvoltage and EMI issues correlated to the number of components. Planar busbar is a good candidate to reduce interconnection inductance in high power inverters compared with cables. The effect of different transient current loops on busbar physical structure of the high-voltage highlevel diode-clamped converters is highlighted. Design considerations of proper planar busbar are also presented to optimise the overall design of diode-clamped converters.

The highs (B1H) and lows (B1L) of human heart B1-adrenoceptors (AR)

The 1AR has two binding sites which can be activated to cause cardiostimulation. The first, termed, 1HAR (high affinity site of 1AR) is activated by noradrenaline and adrenaline and is blocked by relatively low concentrations of β-blockers including carvedilol (Kaumann and Molenaar, 2008). The other, termed, 1LAR (low affinity site of 1AR) has lower affinity for noradrenaline and adrenaline and is activated by some β-blockers including CGP12177 and pindolol, at higher concentrations than those required to block the receptor (Kaumann and Molenaar, 2008). (-)-CGP12177 is a non-conventional partial agonist that causes modest and transient increases of contractile force in human atrial trabeculae (Kaumann and Molenaar, 2008). These effects are markedly increased and maintained by inhibition of phosphodiesterase PDE3. The stimulant effects of (-)-CGP12177 at human β1ARs was verified with recombinant receptors (Kaumann and Molenaar, 2008). However, in a recent report it was proposed that the positive inotropic effects of CGP12177 are mediated through 3ARs in human right atrium (Skeberdis et al 2008). This proposal was not consistent with the lack of blockade of (-)-CGP12177 inotropic effects or increases in L-type Ca2+ current (ICa-L ) by the β3AR blocker 1 μM LY748,337 (Christ et al, 2010). On the otherhand, (-)-CGP12177 increases in inotropic effects and ICa-L were blocked by (-)-bupranolol 1-10 μM (Christ et al, 2010). Chronic infusion of (-)-CGP 12177 (10 mg/Kg/24 hours) for four weeks in an aortic constriction mouse model of heart failure caused an increase in left ventricular wall thickness, fibrosis and inflammation-related left ventricular gene expression levels. Christ T et al (2010) Br J Pharmacol, In press Kaumann A and Molenaar P (2008) Pharmacol Ther 118, 303-336 Skeberdis VA et al (2008) J Clin Invest, 118, 3219-3227

Effects of an acute α-lactalbumin manipulation on mood and food hedonics in high- and low-trait anxiety individuals

Serotonergic hypofunction is associated with a depressive mood state, an increased drive to eat and preference for sweet (SW) foods. High-trait anxiety individuals are characterised by a functional shortage of serotonin during stress, which in turn increases their susceptibility to experience a negative mood and an increased drive for SW foods. The present study examined whether an acute dietary manipulation, intended to increase circulating serotonin levels, alleviated the detrimental effects of a stress-inducing task on subjective appetite and mood sensations, and preference for SW foods in high-trait anxiety individuals. Thirteen high- (eleven females and two males; anxiety scores 45·5 (sd 5·9); BMI 22·9 (sd 3·0)kg/m2) and twelve low- (ten females and two males; anxiety scores 30·4 (sd 4·8); BMI 23·4 (sd 2·5) kg/m2) trait anxiety individuals participated in a placebo-controlled, two-way crossover design. Participants were provided with 40 g α-lactalbumin (LAC; l-tryptophan (Trp):large neutral amino acids (LNAA) ratio of 7·6) and 40 g casein (placebo) (Trp:LNAA ratio of 4·0) in the form of a snack and lunch on two test days. On both the test days, participants completed a stress-inducing task 2 h after the lunch. Mood and appetite were assessed using visual analogue scales. Changes in food hedonics for different taste and nutrient combinations were assessed using a computer task. The results demonstrated that the LAC manipulation did not exert any immediate effects on mood or appetite. However, LAC did have an effect on food hedonics in individuals with high-trait anxiety after acute stress. These individuals expressed a lower liking (P = 0·012) and SW food preference (P = 0·014) after the stressful task when supplemented with LAC.

Industrial design in endoscopy : the development of a tissue and organ extractor

Throughout history, developments in medicine have aimed to improve patient quality of life, and reduce the trauma associated with surgical treatment. Surgical access to internal organs and bodily structures has been traditionally via large incisions. Endoscopic surgery presents a technique for surgical access via small (1 Omm) incisions by utilising a scope and camera for visualisation of the operative site. Endoscopy presents enormous benefits for patients in terms of lower post operative discomfort, and reduced recovery and hospitalisation time. Since the first gall bladder extraction operation was performed in France in 1987, endoscopic surgery has been embraced by the international medical community. With the adoption of the new technique, new problems never previously encountered in open surgery, were revealed. One such problem is that the removal of large tissue specimens and organs is restricted by the small incision size. Instruments have been developed to address this problem however none of the devices provide a totally satisfactory solution. They have a number of critical weaknesses: -The size of the access incision has to be enlarged, thereby compromising the entire endoscopic approach to surgery. - The physical quality of the specimen extracted is very poor and is not suitable to conduct the necessary post operative pathological examinations. -The safety of both the patient and the physician is jeopardised. The problem of tissue and organ extraction at endoscopy is investigated and addressed. In addition to background information covering endoscopic surgery, this thesis describes the entire approach to the design problem, and the steps taken before arriving at the final solution. This thesis contributes to the body of knowledge associated with the development of endoscopic surgical instruments. A new product capable of extracting large tissue specimens and organs in endoscopy is the final outcome of the research.

Implementing value management as a decision-making tool in the design stages of design and build construction projects : a methodology for improved cost optimization

Value Management (VM) has been proven to provide a structured framework, together with other supporting tools and techniques, that facilitate effective decision-making in many types of projects, thus achieving ‘best value’ for clients. One of the major success factors of VM in achieving better project objectives for clients is through the provision of beneficial input by multi-disciplinary team members being involved in critical decision-making discussions during the early stage of construction projects. This paper describes a doctoral research proposal based on the application of VM in design and build construction projects, especially focusing on the design stage. The research aims to study the effects of implementing VM in design and build construction projects, in particular how well the methodology addresses issues related to cost overruns resulting from poor coordination and overlooking of critical constructability issues amongst team members in construction projects in Malaysia. It is proposed that through contractors’ early involvement during the design stage, combined with the use of the VM methodology, particularly as a decision-making tool, better optimization of construction cost can be achieved, thus promoting more efficient and effective constructability. The main methods used in this research involve a thorough literature study, semi-structured interviews, and a survey of major stakeholders, a detailed case study and a VM workshop and focus group discussions involving construction professionals in order to explore and possibly develop a framework and a specific methodology for the facilitating successful application of VM within design and build construction projects.