Assessment of beginners' front-crawl stroke efficiency

Efficiency in front-crawl stroke has been inferred primarily by means of the analysis of arm actions, specifically, stroke frequency and stroke length. The objective of the present study was to investigate whether swimming efficiency could be better assessed in children still learning the front-crawl stroke by analyzing the movement pattern as a whole. Forty-two children enrolled in private swimming programs volunteered to participate in the study. The task consisted of swimming 30 m as fast as possible. Three experts analyzed the movement pattern of the participants using a checklist. Both stroke frequency and stroke length were calculated. The correlation coefficients between the time taken to swim and both the stroke frequency and stroke length were not significant, but the total and components of the checklist scores were. Results indicate that the swimming efficiency of children learning the front-crawl stroke can be better assessed by analyzing their whole movement pattern.

ANNEALING BEHAVIOR OF RAFM ODS-EUROFER STEEL

Oxide-dispersion-strengthened (ODS) ferritic-martensitic steels are candidates for applications in fusion power plants where micro structural long-term stability at temperatures of 650 degrees C to 700 degrees C are required. The microstructural stability of 80% cold-rolled reduced-activation ferritic-martensitic 9% Cr ODS-Eurofer steel was investigated within a wide range of temperatures (300 degrees C to 1350 degrees C). Fine oxide dispersion is very effective to prevent recrystallization in the ferritic phase field. The low recrystallized volume fraction (<0.1) found in samples annealed at 800 degrees C is associated with the nuclei found at prior grain boundaries and around coarse M23C6 particles. The combination of retarding effects such as Zener drag and concurrent recovery decrease the local stored energy and impede further growth of the recrystallization nuclei. Above 90 degrees C, martensitic transformation takes place with consequent coarsening. Significant changes in crystallographic texture are also reported.

Experimental study on vortex-induced motions of a semi-submersible platform with four square columns, Part I: Effects of current incidence angle and hull appendages

An experimental study on Vortex-Induced Motion (VIM) of the semi-submersible platform concept with four square columns is presented. Model tests were carried out to check the influence of different headings and hull appendages (riser supports located at the pontoons; fairleads and the mooring stretches located vertically at the external column faces; and hard pipes located vertically at the internal column faces). The results comprise in-line, transverse and yaw motions, as well as combined motions in the XY plane, drag and lift forces and spectral analysis. The main results showed that VIM in the transverse direction occurred in a range of reduced velocity 4.0 up to 14.0 with amplitude peaks around reduced velocities around 7.0 and 8.0. The largest transverse amplitudes obtained were around 40% of the column width for 30 degrees and 45 degrees incidences. Another important result observed was a considerable yaw motion oscillation, in which a synchronization region could be identified as a resonance phenomenon. The largest yaw motions were verified for the 0 degrees incidence and the maxima amplitudes around 4.5 degrees. The hull appendages located at columns had the greatest influence on the VIM response of the semi-submersible. (C) 2012 Elsevier Ltd. All rights reserved.

Identification of novel components of NAD-utilizing metabolic pathways and prediction of their biochemical functions

Nicotinamide adenine dinucleotide (NAD) is a ubiquitous cofactor participating in numerous redox reactions. It is also a substrate for regulatory modifications of proteins and nucleic acids via the addition of ADP-ribose moieties or removal of acyl groups by transfer to ADP-ribose. In this study, we use in-depth sequence, structure and genomic context analysis to uncover new enzymes and substrate-binding proteins in NAD-utilizing metabolic and macromolecular modification systems. We predict that Escherichia coli YbiA and related families of domains from diverse bacteria, eukaryotes, large DNA viruses and single strand RNA viruses are previously unrecognized components of NAD-utilizing pathways that probably operate on ADP-ribose derivatives. Using contextual analysis we show that some of these proteins potentially act in RNA repair, where NAD is used to remove 2'-3' cyclic phosphodiester linkages. Likewise, we predict that another family of YbiA-related enzymes is likely to comprise a novel NAD-dependent ADP-ribosylation system for proteins, in conjunction with a previously unrecognized ADP-ribosyltransferase. A similar ADP-ribosyltransferase is also coupled with MACRO or ADP-ribosylglycohydrolase domain proteins in other related systems, suggesting that all these novel systems are likely to comprise pairs of ADP-ribosylation and ribosylglycohydrolase enzymes analogous to the DraG-DraT system, and a novel group of bacterial polymorphic toxins. We present evidence that some of these coupled ADP-ribosyltransferases/ribosylglycohydrolases are likely to regulate certain restriction modification enzymes in bacteria. The ADP-ribosyltransferases found in these, the bacterial polymorphic toxin and host-directed toxin systems of bacteria such as Waddlia also throw light on the evolution of this fold and the origin of eukaryotic polyADP-ribosyltransferases and NEURL4-like ARTs, which might be involved in centrosomal assembly. We also infer a novel biosynthetic pathway that might be involved in the synthesis of a nicotinate-derived compound in conjunction with an asparagine synthetase and AMPylating peptide ligase. We use the data derived from this analysis to understand the origin and early evolutionary trajectories of key NAD-utilizing enzymes and present targets for future biochemical investigations.

Comparison between frequency domain and time domain riser analysis

In the optimization or parametric analyses of risers, several configurations must be analyzed. It is laborious to perform time domain solutions for the dynamic analysis, since they are time-consuming tasks. So, frequency domain solutions appear to be a possible alternative, mainly in the early stages of a riser design. However, frequency domain analysis is linear and requires that nonlinear effects are treated. The aim of this paper is to present a possible way to treat some of these nonlinearities, using an iterative process together with an analytical correction, and compare the results of a frequency domain analysis with the those of a full nonlinear analysis. [DOI: 10.1115/1.4006149]

Experimental model identification of open-frame underwater vehicles

Most of the works published on hydrodynamic parameter identification of open-frame underwater vehicles focus their attention almost exclusively on good coherence between simulated and measured responses, giving less importance to the determination of “actual values” for hydrodynamic parameters. To gain insight into hydrodynamic parameter experimental identification of open-frame underwater vehicles, an experimental identification procedure is proposed here to determine parameters of uncoupled and coupled models. The identification procedure includes: (i) a prior estimation of actual values of the forces/torques applied to the vehicle, (ii) identification of drag parameters from constant velocity tests and (iii) identification of inertia and coupling parameters from oscillatory tests; at this stage, the estimated values of drag parameter obtained in item (ii) are used. The procedure proposed here was used to identify the hydrodynamic parameters of LAURS—an unmanned underwater vehicle developed at the University of São Paulo. The thruster–thruster and thruster–hull interactions and the advance velocity of the vehicle are shown to have a strong impact on the efficiency of thrusters appended to open-frame underwater vehicles, especially for high advance velocities. Results of tests with excitation in 1-DOF and 3-DOF are reported and discussed, showing the feasibility of the developed procedure.

Vad helhetssynen skulle betytt för tre kvinnor som varit sjukskrivna : Om att använda systemteori inom rehabilitering

Temat för denna uppsats var att undersöka ett systemteoretiskt arbetssätt i rehabilitering. I den här undersökningen har tre kvinnor som tidigare varit sjukskrivna av psykiska orsaker, intervjuats för att de skulle få ge sin syn på hur ett systemteoretiskt arbetssätt skulle kunna ha hjälpt dem i deras rehabilitering. Vidare vilken funktion deras sjukdom fyllt i deras system och för dom själva. Det fanns en tanke om att deras sjukdom var orsakad av många faktorer, vilket visade sig vara fallet. Urvalet var ett så kallat bekvämlighets urval. Metoden som använts var halvstrukturerade intervjuer med hjälp av en intervju guide. Tolkningen som användes var hermeneutisk. Arbetet begränsades genom att kvinnor som varit sjukskrivna valdes ut. Andra kriterier var att dom skulle ha familj som bodde hemma, minst tre barn och en sambo eller man, vidare att dom kom från små orter i Västernorrlands inland. Resultatet visar att de överlag var positivt inställda till ett systemteoretiskt synsätt, att de saknade att vissa instanser inom rehabilitering inte tog hänsyn till komplexitet i deras liv, och att de känner sig misstrodda av försäkringskassan. Sjukdomen fyllde för alla tre en funktion av signal på obalans i ett snedbelastat system. Vidare var de tre kvinnorna sjukare än vad omgivningen och dom själva trott. De saknade alla tre, från de rehabiliterande enheterna, en helhetssyn på dem och deras situation. Systemteorin kan verka ytterst komplicerad när man läser om cybernetiken till exempel. Men som behandlare behöver man inte lägga det på en komplicerad nivå. Det räcker att man i stora drag vet vad systemteorin handlar om och att man är medveten om vilken roll kommunikation och interaktion spelar, och vilken roll man hamnar i som behandlare i det psykosociala arbetet.

Aplicación del método de los volúmenes finitos al cálculo del parámetro de masa añadida de un cilindro vibrante en el seno de un fluido

Máster Universitario en Sistemas Inteligentes y Aplicaciones Numéricas en Ingeniería (SIANI)

Meccanismi di formazione dei tubi di lava

Two analytical models are proposed to describe two different mechanisms of lava tubes formation. A first model is introduced to describe the development of a solid crust in the central region of the channel, and the formation of a tube when crust widens until it reaches the leve\'es. The Newtonian assumption is considered and the steady state Navier- Stokes equation in a rectangular conduit is solved. A constant heat flux density assigned at the upper flow surface resumes the combined effects of two thermal processes: radiation and convection into the atmosphere. Advective terms are also included, by the introduction of velocity into the expression of temperature. Velocity is calculated as an average value over the channel width, so that lateral variations of temperature are neglected. As long as the upper flow surface cools, a solid layer develops, described as a plastic body, having a resistance to shear deformation. If the applied shear stress exceeds this resistance, crust breaks, otherwise, solid fragments present at the flow surface can weld together forming a continuous roof, as it happens in the sidewall flow regions. Variations of channel width, ground slope and effusion rate are analyzed, as parameters that strongly affect the shear stress values. Crust growing is favored when the channel widens, and tube formation is possible when the ground slope or the effusion rate reduce. A comparison of results is successfully made with data obtained from the analysis of pictures of actual flows. The second model describes the formation of a stable, well defined crust along both channel sides, their growing towards the center and their welding to form the tube roof. The fluid motion is described as in the model above. Thermal budget takes into account conduction into the atmosphere, and advection is included considering the velocity depending both on depth and channel width. The solidified crust has a non uniform thickness along the channel width. Stresses acting on the crust are calculated using the equations of the elastic thin plate, pinned at its ends. The model allows to calculate the distance where crust thickness is able to resist the drag of the underlying fluid and to sustain its weight by itself, and the level of the fluid can lower below the tube roof. Viscosity and thermal conductivity have been experimentally investigated through the use of a rotational viscosimeter. Analyzing samples coming from Mount Etna (2002) the following results have been obtained: the fluid is Newtonian and the thermal conductivity is constant in a range of temperature above the liquidus. For lower temperature, the fluid becomes non homogeneous, and the used experimental techniques are not able to detect any properties, because measurements are not reproducible.

Effetti idrodinamici prodotti dal costume tecnico sul nuotatore

L’introduzione dei costumi tecnici nel nuoto ha portato miglioramenti senza precedenti sulla prestazione. I miglioramenti nella velocità di nuoto sono stati attribuiti dalla letteratura a riduzioni nelle resistenze idrodinamiche sul nuotatore. Tuttavia, gli effetti specifici dovuti all’utilizzo di questo tipo di costume non sono ancora completamente chiariti. Questa tesi aveva l’obiettivo di indagare gli effetti del costume tecnico sul galleggiamento statico, sulla posizione del corpo e sulla resistenza idrodinamica in avanzamento passivo. Nello studio preliminare sono stati misurati la spinta idrostatica, i volumi polmonari dinamici e la circonferenza toracica di 9 nuotatori che indossavano un costume tradizionale o un costume tecnico in gomma sintetica. Indossare il costume tecnico ha determinato una riduzione significativa del galleggiamento statico, e la compressione toracica causata da questo tipo di costume potrebbe avere una relazione con la significativa riduzione dei volumi polmonari misurati quando il nuotatore indossa questo tipo di costume. Un successiva analisi prevedeva il traino passivo di 14 nuotatori che mantenevano la miglior posizione idrodinamica di scivolamento indossando un costume tradizionale, tecnico in tessuto e tecnico in gomma. La posizione del corpo in avanzamento è stata misurata con un’analisi cinematica. La resistenza passiva indossando i costumi tecnici è risultata significativamente minore per entrambi i costumi tecnici rispetto alla prova con costume tradizionale. L’analisi condotta attraverso modelli di regressione lineari ha mostrato che una parte della riduzione della resistenza passiva era legata a proprietà intrinseche dei costumi tecnici. Tuttavia, anche l’area di impatto frontale determinata dall’inclinazione del tronco del soggetto in scivolamento e l’inclinazione degli arti inferiori hanno mostrato una marcata influenza sulla resistenza idrodinamica passiva. Pertanto, la riduzione di resistenza idrodinamica durante lo scivolamento passivo effettuato con costume tecnico da nuoto è attribuibile, oltre all’effetto del materiale di composizione del costume, ad una variazione della posizione del corpo del nuotatore.

Analisi, progettazione e realizzazione di un prototipo di scheduler per attivita commerciali

Negli ultimi anni si è verificato un enorme cambiamento per quanto riguarda le tecnologie utilizzate nello sviluppo di applicazioni, spostandosi sempre verso soluzioni più innovative. In particolare l'utente, diventando sempre più esperto, si ritrova ad essere sempre più esigente. Qui nasce la necessità di modernizzare la gestione degli appuntamenti con la clientela da parte delle attività commerciali tramite l'uso di uno scheduler online. Lo scopo di questo documento è quello di illustrare come è stato realizzato un prototipo di questo sistema, partendo dalle interviste ai committenti e analisi dei relativi problemi, per arrivare poi alla sua realizzazione, utilizzando tecnologie e design innovativi e di ultima generazione.

Diagnose der Residuumszirkulation und ihre Bedeutung für die Klimavariabilität der Stratosphäre

Mit einem in dieser Arbeit entwickelten Diagnose-Werkzeug wird im Rahmenrneines einfachen mechanistischenModells die Residuumszirkulation in der Stratosphärernermittelt. Die Residuumszirkulation wird als eine Schlüsselgröße für diernKlimavariabilität der Stratosphäre angesehen. Für die Diagnose wird mit einemrnmechanistischem Modell die Ausbreitung und das Brechen planetarer Wellenrnbeschrieben und der daraus resultierende Wellenantrieb bestimmt. Dieser Wellenantriebrnwird verwendet, um mit der numerischen Lösung einer elliptischenrnDifferentialgleichung die Residuumszirkulation zu berechnen.rnDieses Diagnose-Werkzeug wird genutzt, um in atmosphärischen Reanalysedatenrnden Zusammenhang der Residuumszirkulation mit verschiedenen Modenrnstratosphärischer Klimavariabilität zu untersuchen. Während für unterschiedlichernPhasen der quasi-zweijährigen Schwingung und der Nordatlantischen Oszillationrndie Residuumszirkulation deutliche Unterschiede aufzeigt, kann ein Einflussrndes 11-jährigen Sonnenfleckenzyklus auf die Residuumszirkulation nichtrneindeutig nachgewiesen werden. Eine Datenstudie zeigt, dass in den WintermonatenrnDezember und Januar die Stärke der Residuumszirkulation mit derrnTemperatur der unteren polaren Stratosphäre signifikant korreliert ist.

Multilevel Domain Decomposition Algorithms for Monolithic Fluid-Structure Interaction Problems with Application to Haemodynamics

Finite element techniques for solving the problem of fluid-structure interaction of an elastic solid material in a laminar incompressible viscous flow are described. The mathematical problem consists of the Navier-Stokes equations in the Arbitrary Lagrangian-Eulerian formulation coupled with a non-linear structure model, considering the problem as one continuum. The coupling between the structure and the fluid is enforced inside a monolithic framework which computes simultaneously for the fluid and the structure unknowns within a unique solver. We used the well-known Crouzeix-Raviart finite element pair for discretization in space and the method of lines for discretization in time. A stability result using the Backward-Euler time-stepping scheme for both fluid and solid part and the finite element method for the space discretization has been proved. The resulting linear system has been solved by multilevel domain decomposition techniques. Our strategy is to solve several local subproblems over subdomain patches using the Schur-complement or GMRES smoother within a multigrid iterative solver. For validation and evaluation of the accuracy of the proposed methodology, we present corresponding results for a set of two FSI benchmark configurations which describe the self-induced elastic deformation of a beam attached to a cylinder in a laminar channel flow, allowing stationary as well as periodically oscillating deformations, and for a benchmark proposed by COMSOL multiphysics where a narrow vertical structure attached to the bottom wall of a channel bends under the force due to both viscous drag and pressure. Then, as an example of fluid-structure interaction in biomedical problems, we considered the academic numerical test which consists in simulating the pressure wave propagation through a straight compliant vessel. All the tests show the applicability and the numerical efficiency of our approach to both two-dimensional and three-dimensional problems.

Drainage of thin aqueous films between solid surfaces measured with the colloidal probe technique

Understanding liquid flow at the vicinity of solid surfaces is crucial to the developmentrnof technologies to reduce drag. One possibility to infer flow properties at the liquid-solid interface is to compare the experimental results to solutions of the Navier-Stokes equations assuming the no-slip boundary condition (BC) or the slip BC. There is no consensus in the literature about which BC should be used to model the flow of aqueous solutions over hydrophilic surfaces. Here, the colloidal probe technique is used to systematically address this issue, measuring forces acting during drainage of water over a surface. Results show that experimental variables, especially the cantilever spring constant, lead to the discrepancy observed in the literature. Two different parameters, calculated from experimental variables, could be used to separate the data obtained in this work and those reported in the literature in two groups: one explained with the no-slip BC, and another with the slip BC. The observed residual slippage is a function of instrumental variables, showing a trend incompatible with the available physical justifications. As a result, the no-slip is the more appropriate BC. The parameters can be used to avoid situations where the no-slip BC is not satisfied.

Gestione Efficiente di Eventi Complessi su Piattaforma IoT ThingWorx

Nella prima parte di questa tesi viene introdotto il concetto di Internet of Things. Vengono discussi gli elementi costituitivi fondamentali di tale tecnologia, le differenti architetture proposte nel corso degli anni e le sfide che devono ancora essere affrontate per vedere realizzato l’IoT. Questa prima parte si conclude inoltre con due esempi di applicazione dell’IoT. Questi due esempi, Smart City e Smart Healthcare, hanno l’obbiettivo di evidenziare quali sono i vantaggi ed i servizi che possono essere offerti all’utente finale una volta applicato l’IoT. Nel secondo capitolo invece, vengono presentate le funzionalità della piattaforma IoT ThingWorx, la quale mette a disposizione un ambiente di sviluppo per applicazioni IoT con l’obbiettivo di ridurre i tempi e quindi anche i costi di sviluppo delle stesse. Questa piattaforma cerca di ridurre al minimo la necessità di scrivere codice, utilizzando un sistema di sviluppo di tipo “Drag and Drop”. ThingWorx mette anche a disposizione degli SDK per facilitare la programmazione dei device, gestendo soprattutto la parte di comunicazione nodo – piattaforma. Questo argomento viene trattato ampiamente nella parte finale di questo capitolo dopo aver visto quali sono i concetti fondamentali di modellazione e rappresentazione dei dati sui quali si basa la piattaforma. Nel terzo e ultimo capitolo di questa tesi viene presentato innanzitutto il tutorial Android di ThingWorx. Svolgere e successivamente estendere il tutorial ha evidenziato alcune limitazioni del modello iniziale e questo ci ha portato a progettare e sviluppare il componente Aggregated & Complex Event Manager per la gestione di eventi complessi e che permette di sgravare parzialmente la piattaforma da tale compito. La tesi si conclude evidenziando, tramite dei test, alcune differenze fra la situazione iniziale nella quale il componente non viene utilizzato e la situazione finale, nella quale invece viene usato.