Broiler Response to Different Wind Speeds

Broiler production in Brazil has turned into a very competitive activity in the late years. Constant innovation leads to higher productivity maintaining the same cost of production, which is a desirable situation. Lately one characteristic for broiler housing in Brazil has been the increase in birds density requiring the use of controlled environment through the use of fan and fogging systems in order to achieve better birds productive performance. Most Brazilian producer already uses cooling equipment however it is still unknown the right way to control the wind speed and direction towards the birds. This present research has the objective to evaluate the effect of the wind speed on the heat transfer from the birds to the environment for broilers at 27 days old. There was used 200 birds, placed in a wind tunnel measuring 1.10 m high by 1.10m wide x 10.0 m of length, and the birds density varied from 9, 16 and 20 birds/m 2. Two wind speed were simulated 340 rpm (1.0 m/s) and 250 rpm (0.3 m/s). The increase in the wind velocity related to the smaller bird densityled to a higher heat loss and to a more uniform temperature distribution in its exposed areas.

Natural fiber reinforced unsaturated polyester composites - An approach on compression molding

This work has been performed at Tapetes Sao Carlos-Brazil with the cooperation of the DaimlerChrysler Research Center Team in Ulm - Germany. The objective of the present paper is to report the results obtained with natural fiber reinforced unsaturated polyester (UP) composites, concerning surface quality measurements. The fibers that have been chosen for this work were sisal and curaua. The samples were produced by compression molding technique and afterwards submitted to three different tests, namely: a) thermal aging; b) water absorption and c) artificial weathering. The surface parameters measured before and after the tests were gloss, haze, short and long-waviness. The results have shown that after the tests there is a high loss of gloss, a high increase in haze, and a high increase in short and long-waviness as well. Curaua reinforced composites had a slightly better behavior when compared with sisal reinforced composites. The effect of the presence of filler and the addition of thermoplastic polyester (TP) on the material behavior has not been evidently detected. This result shows that the conventional technology/methods applied to UP-Fiberglass systems cannot be transferred to natural fibers without any modification. The fiber-matrix interaction and its response to the presence of additives must be fully understood before a successful processing route can be developed for painted natural fibers reinforced UP. Copyright © 2001 Society of Automotive Engineers, Inc.

Bioaerossóis bacterianos em um hospital

Microbial contamination of an enclosed area may come from outside or be generated within the area itself. In the study described here, bioaerosol levels in hospital air were quantified and related to those found in the air outside, taking into account some of the environmental variables that affect air quality, such as the number of occupants of a room and the type of ventilation. Airborne bacteria were collected for five minute by blowing air at 500 L min -1 in high speed jets on to the surface on plates culture in a single-stage bioaerosol impactor. The mean viable count of bacteria in the air outside in the hospital, São Paulo State, was 77 ± 4 CFU m -3, while in the air inside the hospital it was 302 ± 260 CFU m-3. The operating theatre was the only space sampled with a controlled environment and, after orthopedic surgery, it had the highest bioaerosol count recorded (867 ± 482 CFU m-3). In the enclosed environments, nine bacterial species were identified. Despite the difficulty in establishing precise numbers of bacteria in the bioaerosols in hospital environments, the values obtained demonstrate a need to instigate suitable programs to keep the microbial density low in these environments, and eliminate microorganisms presenting a significant risk to their occupants. It is also recommended that such programs include the monitoring of hospital air, with the aim of defining standards for acceptable numbers of bacteria in the bioaerosol.

Thermoeconomic model considering the environment impacts on thermoelectric power plants: Natural gas versus diesel

In this paper a comparative analysis of the environmental impact caused by the use of natural gas and diesel in thermoelectric power plants utilizing combined cycle is performed. The objective is to apply a thermoeconomical analysis in order to compare the two proposed fuels. In this analysis, a new methodology that incorporates the economical engineering concept to the ecological efficiency once Cardu and Baica [1, 2], which evaluates, in general terms, the environmental impacts caused by CO2, SO2, NOx and Particulate Matter (PM), adopting as reference the air quality standards in vigour is employed. The thermoeconomic model herein proposed utilizes functional diagrams that allow the minimization the Exergetic Manufacturing Cost, which represents the cost of production of electricity incorporating the environmental impact effects to study the performance of the thermoelectric power plant [3,4], It follows that it is possible to determine the environmental impact caused by thermoelectric power plants and, under the ecological standpoint, the use of natural gas as a fuel is the best option compared to the use of the diesel, presenting ecological efficiency values of 0.944 and 0.914 respectively. From the Exergoeconomic point of view of, it was found out that the EMC (Exergetic Manufacturing Cost) is better when natural gas is used as fuel compared to the diesel fuel. Copyright © 2006 by ASME.

Determinação do índice de estresse hídrico em cultura do feijoeiro com termômetro de infravermelho

In order to calculate the daily stress degree of a bean crop submitted to four water regime applications, cover crop and air daily measurements temperatures were accomplished by using a hand-held infrared thermometer. The treatments did not present crop water stress except the control (without irrigation). The highest yield was obtained by the treatment that received less irrigation frequency, and among the treatments that had the same number of irrigation. The largest yield was obtained with the one that received larger amount of applied water. The largest irrigation frequency did not result in larger productivity. The methodologies used for the irrigation planning were efficient for the replacement of soil water. The daily stress degree index was effective in determining crop water stress; and it was reliable presenting negative values in good water soil condition.

Report on maritime transport and the environment for Latin America

Includes bibliography

Estado da arte da obtenção de crédito de carbono via adoção de veículo elétrico

This paper aims to highlight the state of the art of obtaining carbon credits through the use of electric vehicles. This is one of the solutions to significantly reduce the emission of GHG (Greenhouse Gas) emissions in the case of CO 2, NOx, SOx, and CH 4 (thermochemical reactions arising from the combustion of gasoline with ethanol) in motor vehicles. For this quantitative study was done based on the survey of bibliographic data available and the development of basic calculations considering the car fleet of the Country of Brazil and the CO 2 emissions generated by the same. Thus explaining the considerable gain in air quality and reduction of vectors of greenhouse gases in the case of replacing the current fleet of vehicles combustion of hydrocarbon aliphatic chain, for an eco-efficient fleet consists of electric vehicles and/or hybrids.

Tratamento de polímeros com jato de plasma em pressão atmosférica

Pós-graduação em Física - FEG

Avaliação de variáveis ambientais em ambientes destinados a ocupação comum

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Relações entre o tempo atmosférico e doenças cardiorespiratórias na cidade de Cordeirópolis-SP

Pós-graduação em Geografia - IGCE

Desenvolvimento de um modelo termoeconômico que considera os impactos ambientais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Simulação da dispersão de poluentes atmosféricos e avaliação da qualidade do ar na área de abrangência do Distrito Industrial de Barcarena-PA

A poluição atmosférica é considerada atualmente um dos maiores problemas da sociedade contemporânea, por ameaçar sua qualidade de vida, pois gera impactos negativos no meio ambiente natural e antrópico. Dentre as formas de controle da poluição atmosférica de fontes fixas podem-se destacar a diluição das emissões na atmosfera devido aos efeitos de dispersão, a adoção de equipamentos de controle antes do lançamento dos gases ou a realocação de fonte, visto ser uma possibilidade a ser sugerida durante o procedimento de licenciamento ambiental de empreendimentos com potencial poluidor do ar. Atualmente modelos computacionais de dispersão de poluentes na atmosfera vêm sendo amplamente utilizados na simulação da concentração de poluentes, visando auxiliar órgãos ambientais no prognóstico da qualidade do ar ou suprir deficiências de monitoramento de emissões atmosféricas. O presente trabalho estudou a qualidade do ar e avaliou a dispersão de poluentes atmosféricos sobre Vila do Conde e áreas de influência do Distrito Industrial de Barcarena, no município de Barcarena, estado do Pará, com auxílio do modelo AERMOD View, visto a possibilidade de se estabelecer uma relação entre os níveis de emissões dos poluentes na fonte, com as concentrações dos mesmos no ar, bem como identificar pontos críticos de poluição. O Índice de Qualidade do Ar – IQA e as fragilidades das populações humanas das áreas afetadas pelos poluentes atmosféricos, também foram mensurados na pesquisa. A metodologia empregada permitiu mensurar a concentração média de poluentes atmosféricos durante um determinado tempo de modelagem, informações quanto ao alcance da pluma de poluentes foram alcançados também. São fornecidos ainda informações quanto à relação entre o valor de pico e o valor médio da concentração nas áreas receptoras, provocadas por empreendimentos com características operacionais similares ao modelado. Os resultados demostram que a influência de parâmetros meteorológicos, na dispersão de poluentes são indispensáveis e determinantes na previsão do impacto na qualidade do ar e no planejamento do uso e ocupação do solo de áreas que abrigam atividades poluidoras da atmosfera.

Desenvolvimento de biodiesel microemulsionado com reaproveitamento de resíduos de óleos vegetais

Pós-graduação em Engenharia Mecânica - FEG

Estudo da concentração de material particulado em ambientes internos e externos de bibliotecas

Our twenty-first century society and the rhythm of life and work we have to face in our daily routine compel us to spend most of our lifetime in closed environments, in our houses, educational institutions, hospitals, airports, amongst as many others. The study of the air quality in internal environments (IAQ) is very important for monitoring people’s health effects and their environmental comfort in these locations. One essential parameter to analyze this measure is to evaluate the concentration of dispersed particulates in the air, specially focusing on those thinner particles (below the diameter of 2,5 μm), they can pose serious risks for human being because they can remain in the lungs, penetrate through the pores of our skin, amongst other harmful effects on human’s health. In this work the air quality inside the public library Profª Josina Vasques Ferrari and at Unesp public state library was evaluated, both located in Itapeva, as well as a third one, inside the Communitarian Library of the Federal University in Carlos (UFSCar) from march to may in 2012. In those environments it was analyzed if the concentration of particulates pose any real treat to the users. The equipment used for particle sampling in real time was DataRam 4 (Model DR 4000). The results given for those concentrations of particulates in both internal and external environments revealed figures within the safe standard established by the WHO (World Health Organization), from 25 to μg/m³, the only exception occurred on the fifth floor of the UFSCar library, where the average for concentration stayed at 25,30 of μg/m³

Estimativa das emissões de monóxido de carbono por veículos automotivos na cidade de Campinas/SP utilizando o modelo CAL3QHCR

Air pollution is an environmental issue worldwide and frequently cause negative effects on population health and ecosystems on cities. The relationship between climate and atmospheric pollution can be used as a surrogate to the intensity of air pollution. The present and quantity of some gases can be used as indicators to air quality: particulate matter (PM), sulfur dioxide (SO2), carbon monoxide (CO), ozone (O3), and nitrogen dioxide (NO2). Among those gases, CO has its major source within the cities, where automobiles are the main emitter. But measure pollutant concentration are challenging, sometimes because the lack of good equipments due to high costs and of the large variability of models that varies in precision, way of measure and distribution of sellers. Modeling are useful when there are an intend to evaluate air pollution, its sources and evaluate scenarios. This work aims to use CAL3QHCR model developed by the U.S Environmental Protection Agency (EPA) to generate predictive surfaces of CO concentration distribution on a site within Campinas city, located in São Paulo state, Brazil. CAL3QHCR model use data urban automobile circulation to generate spatial results for CO distribution. We observed that the pollution concentration was lower on our modeling than the concentrations measured by Companhia Ambiental do Estado de São Paulo (CETESB), the main environmental company on the São Paulo state. Also the correlation between average estimates of our model and the measure by CETESB was weak, indicating that the model used on this study need to be or better parameterized, or the scale we measured of CO emissions need to be rescaled. Although the model failed to correlate to CETESB data, maybe one that explore the estimated emissions distributed within the sites to understand spatial distributions of CO on the regions. Also, the generated information can also be used to other studies, and come to be useful to explain heat island