Nanocompósitos ternários de amido termoplástico e poli(Butadieno maleatado)

Liquid polybutadiene (PBLH) was modified with maleic anhydride (MA). The material (PBLHM) was characterized and used to prepare hybrid materials by blending with glycerol-plasticized cassava starch (TPS) and an organophilic clay at 5 wt% content. Processing was performed by extrusion under mild conditions and led to TPS/PBLHM/clay hybrids, at 95/5 to 85/15 TPS/PBLHM compositions, which were characterized by contact angle measurements, X-ray diffraction and mechanical analysis. The results revealed a reduction in the hydrophilicity and the reinforcement of the hybrid materials. Biodegradability tests showed that the addition of clay and of PBLHM led to materials with high biodegradability.

Efeito do teor de umidade sobre o pré-tratamento a vapor e a hidrólise enzimática do bagaço de cana-de-açúcar

The effect of moisture content in the steam treatment and enzymatic hydrolysis of sugarcane bagasse was evaluated. Steam treatment was perfomed at 195-210 ºC for 4-8 min using cane bagasse with moisture contents in the range 16-100 wt% (dry basis). Increased moisture contents not only had a positive influence in recovery of main cane biomass components but also resulted in better substrates for enzymatic hydrolysis. As a result, drying is not required for optimal pretreatment and enzymatic hydrolysis of sugarcane bagasse, which can be processed into second generation ethanol immediately after crushing and hot water washing.

Isolamento do tungstênio da volframita da mina de Igarapé Manteiga (Rondônia - Brasil) por lixiviação ácida

We report results of the efficiency of tungsten extraction from wolframite concentrate (containing 61.5 wt % WO3) from the Igarapé Manteiga mine (state of Rondônia, Brazil) through acid leaching with strong mineral acids at 100 ºC and 400 rpm for 2-4 h. HCl yielded insoluble matter containing the highest WO3 content (90 wt %). This solid was dissolved in concentrated NH3(aq) at 25 ºC and the insoluble matter filtrated. The filtrate was slowly evaporated. 70 wt % of the tungsten present in the starting concentrate material was recovered as ammonium paratungstate (APT).

Síntese e caracterização de hidrogéis compósitos a partir de copolímeros acrilamida-acrilato e caulim: efeito da constituição de diferentes caulins do nordeste brasileiro

Superabsorbent hydrogels based on poly (acrylamide-co-acrylate) and different kaolins, were prepared by free-radical aqueous copolymerization. FTIR and WAXS techniques were employed for characterization of a series of hydrogels, obtained by varying the percentage of clay, crosslinking and constitution of kaolin. The water absorbency at equilibrium (Weq) decreased with increasing clay content and the amount of crosslinking agent. Superabsorbent hydrogel (Weq > 1084 g H2O/g gel) was obtained as 10 wt% of white kaolin and 0.05 mol% of crosslinking agent were used. The hydrogel proved sensitive to pH variation and the presence of salts.

Processamento de placas de circuito impresso de equipamentos eletroeletrônicos de pequeno porte

A hydrometallurgical process applicable to printed circuit boards of small electrical and electronic devices was developed. This involved three leaching steps (60 ºC, 2 h): 6 mol L-1 NaOH, 6 mol L-1 HCl and aqua regia. NaOH removed the resin and flame retardant that covered the circuit boards. HCl dissolved the most electropositive metals and a small amount of copper (~0.3 wt%). Aqua regia dissolved the noble metals. Silver precipitated as AgCl. Gold and platinum were quantitatively extracted with pure methyl-isobutylketone and Alamine 336 (10 % vol. in kerosene), respectively. Slow evaporation of the raffinate crystallized CuCl2.4H2O (89% yield).

Characterization and catalytic performance of potassium loaded on rice husk silica and zeolite nay for transesterification of jatropha seed oil

Rice husk silica (RHS) and NaY were used as supports for potassium (K) prepared from acetate buffer (B) and acetate (A) solutions. K loading did not destroy the NaY structure, but it caused a decrease in the surface area; the K species resided in micropores and on the external surface. In contrast, K loading resulted in the collapse and a decrease in the surface area of RHS. It was found that 12K/NaY-B was the most active catalyst for the transesterification of Jatropha seed oil. The minimum K content in K/NaY-B that provided complete conversion of the Jatropha seed oil was 11 wt%, and the biodiesel yield was 77.9%.

Produção de concentrados de ácidos graxos por hidrólise de óleos vegetais mediada por lipase vegetal

The aim of this work was to verify the ability of enzymatic crude extract from dormant castor bean seeds to yield concentrated fatty acids by hydrolysis of polyunsaturated vegetable oils such as corn and sunflower. The enzymatic extract exhibited higher activity towards corn oil, which was selected for further studies to determine optimum hydrolysis conditions by factorial design. Maximum hydrolysis percentage (≈84%) was reached at 60% wt. oil:buffer acetate 100 mM pH 4.5, 33 ºC and 5.0% wt. of crude extract after 70 min of reaction. These results suggest that the use of low-cost lipase from castor bean seeds has potential for oil hydrolysis.

Líquidos iônicos como plastificantes em blendas de borracha nitrílica/polianilina

Two imidazolium-based ionic liquids (C4MIMTf2N and C4MIMBF4) were used to verify their influence on polyaniline (PANI) and nitrile rubber (NBR)/PANI blend properties and the vulcanization process. High conductivity values were observed for PANI-C4MIMTf2N samples and no interference was found for the C4MIMBF4 samples. These materials were added to NBR by mechanical mixing. Based on the torque results, the presence of C4MIMBF4 does not protect the vulcanization reaction of NBR with PANI as performed by C4MIMTf2N. The highest conductivity value was obtained with 7 wt. % of PANI-DSBA-C4MIMTf2N (10-6 S/cm). This result is attributed to the more effective interaction of PANI and NBR phases promoted by the ionic liquid.

ESTERIFICAÇÃO E TRANSESTERIFICAÇÃO SIMULTÂNEAS DE ÓLEOS ÁCIDOS UTILIZANDO CARBOXILATOS LAMELARES DE ZINCO COMO CATALISADORES BIFUNCIONAIS

Palm oil containing 40% fatty acids was converted to methyl esters using zinc carboxylates as the esterification/transesterification catalyst. The reaction was optimized using a factorial design in which the effects of the alcohol:fatty acids molar ratio (MRAG) and the catalyst concentration (CAT) were assessed. The best conversion was achieved with CAT at 4 wt% and MRAG at 4:1. However, the solid catalyst presented significant structural changes after use. For instance, laurate anions were replaced by carboxylates of higher molecular mass, leading to the formation of a new catalytically active layered structure. Also, the glycerin obtained as a co-product contained 86 wt% glycerol.

PREPARAÇÃO E CARACTERIZAÇÃO DE MEMBRANAS DE CELULOSE REGENERADA A PARTIR DA CELULOSE EXTRAÍDA DE RESÍDUOS AGROINDUSTRIAIS PARA APLICAÇÃO EM PROCESSOS DE SEPARAÇÃO

The aim of this study was to produce membranes using the adapted cuprammonium method. The cellulose utilized was obtained from recycled agroindustrial residues: sugarcane bagasse, corn stover and soybean hulls. The levels of Cu (II) ions in regenerated cellulose membranes produced with cellulose from bagasse, corn stover and soybean hulls were 0.0236 wt%, 0.0255 wt% and 0.0268 wt%, respectively. These levels were approximately 15 times lower than those observed in previous studies (0.3634 wt%). Cellular viability data show that membranes produced from bagasse cellulose do not present toxicity to the cellular cultures studied. These results demonstrate an evolution in production of regenerated cellulose membranes from agroindustrial residues mainly due to a decrease in the Cu (II) ions level, showing the possibility of application of these systems with improved membranes processing.

A NOVEL POLYACRYLAMIDE-BASED HYDROGEL CROSSLINKED WITH CELLULOSE ACETATE AND PREPARED BY PRECIPITATION POLYMERIZATION

The synthesis of polyacrylamide-cellulose acetate hydrogels by precipitation polymerization in acetone solution is reported herein. These hydrogels exhibit smaller swelling ratios and larger compression moduli than homo polyacrylamide hydrogels. For cellulose acetate concentrations above 20 wt.%, hydrogels with N,N'-methylenebisacrylamide as a crosslinker exhibit swelling ratios and compression moduli similar to those of the hydrogels without the crosslinker. A possible explanation for this behavior is that cellulose acetate crosslinks polyacrylamide via free-radical reaction. The hydrogels obtained without the N,N'-methylenebisacrylamide crosslinker exhibit compression moduli up to 1.7 MPa, making them suitable for tissue engineering applications such as cartilage replacement.

NANOPARTICLES OF TUNGSTEN AS LOW-COST MONOMETALLIC CATALYST FOR SELECTIVE HYDROGENATION OF 3-HEXYNE

Low-cost tungsten monometallic catalysts containing variable amounts of metal (4.5, 7.1 and 8.5%W) were prepared by impregnating alumina with ammonium metatungstate as an inexpensive precursor. The catalysts were characterized using ICP, XPS, XRD, TPR and hydrogen chemisorption. These techniques revealed mainly WO3-Al2O3 (W6+) species on the surface. The effects of the content of W nanoparticles and reaction temperature on activity and selectivity for the partial hydrogenation of 3-hexyne, a non-terminal alkyne, were assessed under moderate conditions of temperature and pressure. The monometallic catalysts prepared were found to be active and stereoselective for the production of (Z )-3-hexene, had the following order: 7.1WN/A > 8.5 WN/A ≥ 4.5 WN/A. Additionally, the performance of the synthesized xWN/A catalysts exhibited high sensitivity to temperature variation. In all cases, the maximum 3-hexyne total conversion and selectivity was achieved at 323 K. The performance of the catalysts was considered to be a consequence of two phenomena: a) the electronic effects, related to the high charge of W (+6), causing an intensive dipole moment in the hydrogen molecule (van der Waals forces) and leading to heterolytic bond rupture; the H+ and H- species generated approach a 3-hexyne adsorbate molecule and cause heterolytic rupture of the C≡C bond into C- = C+; and b) steric effects related to the high concentration of WO3 on 8.5WN/A that block the Al2O3 support. Catalyst deactivation was detected, starting at about 50 min of reaction time. Electrodeficient W6+ species are responsible for the formation of green oil at the surface level, blocking pores and active sites of the catalyst, particularly at low reaction temperatures (293 and 303 K). The resulting best catalyst, 7.1WN/A, has low fabrication cost and high selectivity for (Z )-3-hexene (94%) at 323 K. This selectivity is comparable to that of the classical and more expensive industrial Lindlar catalyst (5 wt% Pd). The alumina supported tungsten catalysts are low-cost potential replacements for the Lindlar industrial catalyst. These catalysts could also be used for preparing bimetallic W-Pd catalysts for selective hydrogenation of terminal and non-terminal alkynes.

COMPARISON BETWEEN ASPHALTENES (SUB)FRACTIONS EXTRACTED FROM TWO DIFFERENT ASPHALTIC RESIDUES: CHEMICAL CHARACTERIZATION AND PHASE BEHAVIOR

Asphaltenes are blamed for various problems in the petroleum industry, especially formation of solid deposits and stabilization of water-in-oil emulsions. Many studies have been conducted to characterize chemical structures of asphaltenes and assess their phase behavior in crude oil or in model-systems of asphaltenes extracted from oil or asphaltic residues from refineries. However, due to the diversity and complexity of these structures, there is still much to be investigated. In this study, asphaltene (sub)fractions were extracted from an asphaltic residue (AR02), characterized by NMR, elemental analysis, X-ray fluorescence and MS-TOF, and compared to asphaltene subfractions obtained from another asphaltic residue (AR01) described in a previous article. The (sub)fractions obtained from the two residues were used to prepare model-systems containing 1 wt% of asphaltenes in toluene and their phase behavior was evaluated by measuring asphaltene precipitation onset using optical microscopy. The results obtained indicated minor differences between the asphaltene fractions obtained from the asphaltic residues of distinct origins, with respect to aromaticity, elemental composition (CHN), presence and content of heteroelements and average molar mass. Regarding stability, minor differences in molecule polarity appear to promote major differences in the phase behavior of each of the asphaltene fractions isolated.

Syntypaikkalajitellun sekajätteen koostumuksen sekä palamisteknisten ominaisuuksien selvitys Etelä-Karjalan alueella

Etelä-Karjalan alueen lajittelututkimuksen tavoitteena oli selvittää alueella syntyvän syntypaikkalajitellun sekajätteen koostumus sekä jätteen palamistekniset ominaisuudet. Palamisteknisinä ominaisuuksina selvitettiin jätteen kosteuspitoisuus, tuhkapitoisuus sekä tehollinen lämpöarvo saapumistilassa. Lisäksi pyrittiin löytämään ratkaisuja kaatopaikkakuormituksen pienentämiselle. Saatuja tuloksia verrattiin aiemmin Suomessa tehtyihin jätekoostumustutkimuksiin ja palamisteknisten ominaisuuksien selvityksiin. Lajittelututkimuksen tulosten perusteella erilliskeräys tarvitsee tehostamista. Biohajoavaa jätettä alueelta kerätyistä otoksista oli 51 m-%, josta biojätettä oli noin 24 m-%. Lisäksi jätteestä kierrätykseen kelpaavia jakeita oli 21 m-%. Palamisteknisten ominaisuuksien määrityksessä tulokset olivat kuivajätteen osalta seuraavat: kosteuspitoisuus 29 %, tehollinen lämpöarvo saapumistilassa 15 MJ/kg ja tuhkapitoisuus kuiva-aineesta 16 %. Tutkimuksesta saadut tulokset ovat linjassa referenssitutkimusten tulosten kanssa. Kaatopaikkakuormituksen vähentämisessä keskeisiä toimenpiteitä ovat tiedotus ja neuvonta. Lisäksi erilliskeräyspisteiden sijoittelulla ja määrän lisäämisellä voidaan saada vähennettyä kierrätyskelpoisen jätteen loppusijoitusta kaatopaikalle. Kierrätyskelvottomien jakeiden poltolla saadaan myös pienennettyä kaatopaikalle loppusijoitettavan jätteen määrää. Syntypaikkalajitellun sekajätteen seassa oli runsaasti polttokelpoista materiaalia. Massapolttoon kelpaavaa jätteestä oli 92 m-% ja energiajätteeseen kelpaavaa 47 m-%. Näistä 13 m-% oli kierrätykseen kelpaavaa jaetta, joka tulisi ohjata kierrätykseen.

Enhancing performance of paper coatings by tailor-made plastic pigments

The paper industry is constantly looking for new ideas for improving paper products while competition and raw material prices are increasing. Many paper products are pigment coated. Coating layer is the top layer of paper, thus by modifying coating pigment also the paper itself can be altered and value added to the final product. In this thesis, synthesis of new plastic and hybrid pigments and their performance in paper and paperboard coating is reported. Two types of plastic pigments were studied: core-shell latexes and solid beads of maleimide copolymers. Core-shell latexes with partially crosslinked hydrophilic polymer core of poly(n-butyl acrylate-co-methacrylic acid) and a hard hydrophobic polystyrene shell were prepared to improve the optical properties of coated paper. In addition, the effect of different crosslinkers was analyzed and the best overall performance was achieved by the use of ethylene glycol dimethacrylate (EGDMA). Furthermore, the possibility to modify core-shell latex was investigated by introducing a new polymerizable optical brightening agent, 1-[(4-vinylphenoxy)methyl]-4-(2-henylethylenyl)benzene which gave promising results. The prepared core-shell latex pigments performed smoothly also in pilot coating and printing trials. The results demonstrated that by optimizing polymer composition, the optical and surface properties of coated paper can be significantly enhanced. The optimal reaction conditions were established for thermal imidization of poly(styrene-co-maleimide) (SMI) and poly(octadecene-co-maleimide) (OMI) from respective maleic anhydride copolymer precursors and ammonia in a solvent free process. The obtained aqueous dispersions of nanoparticle copolymers exhibited glass transition temperatures (Tg) between 140-170ºC and particle sizes from 50-230 nm. Furthermore, the maleimide copolymers were evaluated in paperboard coating as additional pigments. The maleimide copolymer nanoparticles were partly imbedded into the porous coating structure and therefore the full potential of optical property enhancement for paperboard was not achieved by this method. The possibility to modify maleimide copolymers was also studied. Modifications were carried out via N-substitution by replacing part of the ammonia in the imidization reaction with amines, such as triacetonediamine (TAD), aspartic acid (ASP) and fluorinated amines (2,2,2- trifluoroethylamine, TFEA and 2,2,3,3,4,4,4-heptafluorobuthylamine, HFBA). The obtained functional nanoparticles varied in size between 50-217 nm and their Tg from 150-180ºC. During the coating process the produced plastic pigments exhibited good runnability. No significant improvements were achieved in light stability with TAD modified copolymers whereas nanoparticles modified with aspartic acid and those containing fluorinated groups showed the desired changes in surface properties of the coated paperboard. Finally, reports on preliminary studies with organic-inorganic hybrids are presented. The hybrids prepared by an in situ polymerization reaction consisted of 30 wt% poly(styrene- co-maleimide) (SMI) and high levels of 70 wt% inorganic components of kaolin and/or alumina trihydrate. Scanning Electron Microscopy (SEM) images and characterization by Fourier Transform Infrared Spcetroscopy (FTIR) and X-Ray Diffraction (XRD) revealed that the hybrids had conventional composite structure and inorganic components were covered with precipitated SMI nanoparticles attached to the surface via hydrogen bonding. In paper coating, the hybrids had a beneficial effect on increasing gloss levels.