Relating vehicle generated pollutants to urban stormwater quality

Rapid urbanisation and resulting continuous increase in traffic has been recognised as key factors in the contribution of increased pollutant loads to urban stormwater and in turn to receiving waters. Urbanisation primarily increases anthropogenic activities and the percentage of impervious surfaces in urban areas. These processes are collectively responsible for urban stormwater pollution. In this regard, urban traffic and land use related activities have been recognised as the primary pollutant sources. This is primarily due to the generation of a range of key pollutants such as solids, heavy metals and PAHs. Appropriate treatment system design is the most viable approach to mitigate stormwater pollution. However, limited understanding of the pollutant process and transport pathways constrains effective treatment design. This highlights necessity for the detailed understanding of traffic and other land use related pollutants processes and pathways in relation to urban stormwater pollution. This study has created new knowledge in relation to pollutant processes and transport pathways encompassing atmospheric pollutants, atmospheric deposition and build-up on ground surfaces of traffic generated key pollutants. The research study was primarily based on in-depth experimental investigations. This thesis describes the extensive knowledge created relating to the processes of atmospheric pollutant build-up, atmospheric deposition and road surface build-up and establishing their relationships as a chain of processes. The analysis of atmospheric deposition revealed that both traffic and land use related sources contribute total suspended particulate matter (TSP) to the atmosphere. Traffic sources become dominant during weekdays whereas land use related sources become dominant during weekends due to the reduction in traffic sources. The analysis further concluded that atmospheric TSP, polycyclic aromatic hydrocarbons (PAHs) and heavy metals (HMs) concentrations are highly influenced by total average daily heavy duty traffic, traffic congestion and the fraction of commercial and industrial land uses. A set of mathematical equation were developed to predict TSP, PAHs and HMs concentrations in the atmosphere based on the influential traffic and land use related parameters. Dry deposition samples were collected for different antecedent dry days and wet deposition samples were collected immediately after rainfall events. The dry deposition was found to increase with the antecedent dry days and consisted of relatively coarser particles (greater than 1.4 ìm) when compared to wet deposition. The wet deposition showed a strong affinity to rainfall depth, but was not related to the antecedent dry period. It was also found that smaller size particles (less than 1.4 ìm) travel much longer distances from the source and deposit mainly with the wet deposition. Pollutants in wet deposition are less sensitive to the source characteristics compared to dry deposition. Atmospheric deposition of HMs is not directly influenced by land use but rather by proximity to high emission sources such as highways. Therefore, it is important to consider atmospheric deposition as a key pollutant source to urban stormwater in the vicinity of these types of sources. Build-up was analysed for five different particle size fractions, namely, <1 ìm, 1-75 ìm, 75-150 ìm, 150-300 ìm and >300 ìm for solids, PAHs and HMs. The outcomes of the study indicated that PAHs and HMs in the <75 ìm size fraction are generated mainly by traffic related activities whereas the > 150 ìm size fraction is generated by both traffic and land use related sources. Atmospheric deposition is an important source for HMs build-up on roads, whereas the contribution of PAHs from atmospheric sources is limited. A comprehensive approach was developed to predict traffic and other land use related pollutants in urban stormwater based on traffic and other land use characteristics. This approach primarily included the development of a set of mathematical equations to predict traffic generated pollutants by linking traffic and land use characteristics to stormwater quality through mathematical modelling. The outcomes of this research will contribute to the design of appropriate treatment systems to safeguard urban receiving water quality for future traffic growth scenarios. The „real world. application of knowledge generated was demonstrated through mathematical modelling of solids in urban stormwater, accounting for the variability in traffic and land use characteristics.

Fusing loop detector and probe vehicle data to estimate travel time statistics on signalized urban networks

This article presents a methodology that integrates cumulative plots with probe vehicle data for estimation of travel time statistics (average, quartile) on urban networks. The integration reduces relative deviation among the cumulative plots so that the classical analytical procedure of defining the area between the plots as the total travel time can be applied. For quartile estimation, a slicing technique is proposed. The methodology is validated with real data from Lucerne, Switzerland and it is concluded that the travel time estimates from the proposed methodology are statistically equivalent to the observed values.

Physically sound vehicle-driver model for realistic microscopic simulation

In microscopic traffic simulators, the interaction between vehicles is considered. The dynamics of the system then becomes an emergent property of the interaction between its components. Such interactions include lane-changing, car-following behaviours and intersection management. Although, in some cases, such simulators produce realistic prediction, they do not allow for an important aspect of the dynamics, that is, the driver-vehicle interaction. This paper introduces a physically sound vehicle-driver model for realistic microscopic simulation. By building a nanoscopic traffic simulation model that uses steering angle and throttle position as parameters, the model aims to overcome unrealistic acceleration and deceleration values, as found in various microscopic simulation tools. A physics engine calculates the driving force of the vehicle, and the preliminary results presented here, show that, through a realistic driver-vehicle-environment simulator, it becomes possible to model realistic driver and vehicle behaviours in a traffic simulation.

Developing guidelines for intervention to reduce risk of low-speed vehicle run-overs of young children

In Australia, research suggests that up to one quarter of child pedestrian hospitalisations result from driveway run-over incidents (Pinkney et al., 2006). In Queensland, these numbers equate to an average of four child fatalities and 81 children presenting at hospital emergency departments every year (The Commission for Children, Young People and Child Guardian). National comparison shows that these numbers represent a slightly higher per capita rate (23.5% of all deaths). To address this issue, the current research was undertaken with the aim to develop an educative intervention based on data collected from parents and caregivers of young children. Thus, the current project did not seek to use available intervention or educational material, but to develop a new evidence-based intervention specifically targeting driveway run-overs involving young children. To this end, general behavioural and environmental changes that caregivers had undertaken in order to reduce the risk of injury to any child in their care were investigated. Broadly, the first part of this report sought to: • develop a conceptual model of established domestic safety behaviours, and to investigate whether this model could be successfully applied to the driveway setting; • explore and compare sources of knowledge regarding domestic and driveway child safety; and • examine the theoretical implications of current domestic and driveway related behaviour and knowledge among caregivers. The aim of the second part of this research was to develop and test the efficacy of an intervention based on the findings in the first part of the research project. Specifically, it sought to: • develop an educational driveway intervention that is based on current safety behaviours in the domestic setting and informed by existing knowledge of driveway safety and behaviour change theory; and • evaluate its efficacy in a sample of parents and caregivers.

Practice and Procedure: UCPR r 708 - costs order against several defendants and third party

Glenwood Homes Pty Ltd v Everhard [2008] QSC 192 involved the not uncommon situation where one costs order is made against several parties represented by a single firm of solicitors. Dutney J considered the implications when only some of the parties liable for the payment of the costs file a notice of objection to the costs statement served in respect of those costs.

Dumbing it down : where do standards fit?

In Australia, Vocational Education and Training (VET) programs are delivered in a variety of settings. You can be enrolled within a course in a high school, at a technical institution, private training provider or at your place of employment. Recognition of prior learning, on the job training and industry partnerships are strong factors supporting the change of delivery. The curriculum content within these programs has also changed. For example within the Business Services programs, the prerequisite and corequisite skill of touch keyboarding to an Australian Standard has moved from a core requirement in the 1990’s to an elective requirement in the 2000’s. Where a base skill becomes an elective skill, how does this effect the performance and outcomes for the learner, educator, employer and society as a whole? This paper will explore these issues and investigate the current position of standards within the VET curriculum today.

Preface to special issue on digital human modelling for vehicle design and manufacturing

The automotive industry has been the focus of digital human modeling (DHM) research and application for many years. In the highly competitive marketplace for personal transportation, the desire to improve the customer’s experience has driven extensive research in both the physical and cognitive interaction between the vehicle and its occupants. Human models provide vehicle designers with tools to view and analyze product interactions before the first prototypes are built, potentially improving the design while reducing cost and development time. The focus of DHM research and applications began with prediction and representation of static postures for purposes of driver workstation layout, including assessments of seat adjustment ranges and exterior vision. Now DHMs are used for seat design and assessment of driver reach and ingress/egress. DHMs and related simulation tools are expanding into the cognitive domain, with computational models of perception and motion, and into the dynamic domain with models of physical responses to ride and vibration. Moreover, DHMs are now widely used to analyze the ergonomics of vehicle assembly tasks. In this case, the analysis aims to determine whether workers can be expected to complete the tasks safely and with good quality. This preface provides a review of the literature to provide context for the nine new papers presented in this special issue.

Negligible heat strain in armored vehicle officers wearing personal body armor

Objectives This study evaluated the heat strain experienced by armored vehicle officers (AVOs) wearing personal body armor (PBA) in a sub-tropical climate. Methods Twelve male AVOs, aged 35-58 years, undertook an eight hour shift while wearing PBA. Heart rate and core temperature were monitored continuously. Urine specific gravity (USG) was measured before and after, and with any urination during the shift. Results Heart rate indicated an intermittent and low-intensity nature of the work. USG revealed six AVOs were dehydrated from pre through post shift, and two others became dehydrated. Core temperature averaged 37.4 ± 0.3°C, with maximum's of 37.7 ± 0.2°C. Conclusions Despite increased age, body mass, and poor hydration practices, and Wet-Bulb Globe Temperatures in excess of 30°C; the intermittent nature and low intensity of the work prevented excessive heat strain from developing.

The standard bearers : Governing teachers through professional standards

Teacher professional standards have become a key policy mechanism for the reform of teaching and education in recent years. While standards policies claim to improve the quality of teaching and learning in schools today, this paper argues that a disjunction exists between the stated intentions of such programmes and the intelligibility of the practices of government in which they are invested. To this effect, the paper conducts an analytics of government of the recently released National Professional Standards for Teachers (Australian Institute for Teaching and School Leadership, 2011) arguing that the explicit, calculated rationality of the programme exists within a wider field of effects. Such analysis has the critical consequence of calling into question the claims of the programmers themselves thus breaching the self-evidence on which the standards rest.

Determinants of health costs due to farmers’ exposure to pesticides: an empirical analysis

Pesticide spraying by farmers has an adverse impact on their health. However, in studies to date examining farmers’ exposure to pesticides, the costs of ill health and their determinants have been based on information provided by farmers themselves. Some doubt has therefore been cast on the reliability of these estimates. In this study, we address this by conducting surveys among two groups of farmers who use pesticides on a regular basis. The first group is made up of farmers who perceive that their ill health is due to exposure to pesticides and have obtained at least some form of treatment (described in this article as the ‘general farmer group’). The second group is composed of farmers whose ill health has been diagnosed by doctors and who have been treated in hospital for exposure to pesticides (described here as the ‘hospitalised farmer group’). Cost comparisons are made between the two groups of farmers. Regression analysis of the determinants of health costs show that the most important determinants of medical costs for both samples are the defensive expenditure, the quantity of pesticides used per acre per month, frequency of pesticide use and number of pesticides used per hour per day. The results have important policy implications.

Mixed methods research approach to the development and review of competency standards for dietitians

Aim: Competency standards support a range of professional activities including the accreditation of university courses. Reviewing these standards is essential to ensure universities continue to produce well equipped graduates, who can meet the challenge of changing workforce requirements. This paper has two aims: a) to provide an overview of the methodological approaches utilised for compilation and review of the Competency Standards for Dietetics and b) to evaluate the Dietitians Association of Australia’s Competency Standards and capture emerging and contemporary dietetic practice. Methods: A literature review of the methods used to develop Competency Standards for dietitians in Australia, including entry level, advanced level and DAA Fellow competencies and other specific areas of competency, such as public health nutrition and nutrition education is outlined and compared to other allied health professions. The mixed methods methodology used in the most recent review is described in more detail. Results: The history of Dietetic Competency Standards development and review in Australia is compared to dietetic Competency Standards internationally and within other health professions in Australia. The political context in which these standards have been developed in Australia and which has determined their format is also discussed. The results of the most recent Competency Standards review are reported to highlight emerging practice in Australia. Conclusion: The mixed methods approach used in this review provides rich data about contemporary dietetic practice. Our view supports a planned review of all Competency Standards to ensure practice informs education and credentialling and we recommend the Dietitians Association of Australia consider this in future

Optimal planning of electric-vehicle charging stations in distribution systems

With the progressive exhaustion of fossil energy and the enhanced awareness of environmental protection, more attention is being paid to electric vehicles (EVs). Inappropriate siting and sizing of EV charging stations could have negative effects on the development of EVs, the layout of the city traffic network, and the convenience of EVs' drivers, and lead to an increase in network losses and a degradation in voltage profiles at some nodes. Given this background, the optimal sites of EV charging stations are first identified by a two-step screening method with environmental factors and service radius of EV charging stations considered. Then, a mathematical model for the optimal sizing of EV charging stations is developed with the minimization of total cost associated with EV charging stations to be planned as the objective function and solved by a modified primal-dual interior point algorithm (MPDIPA). Finally, simulation results of the IEEE 123-node test feeder have demonstrated that the developed model and method cannot only attain the reasonable planning scheme of EV charging stations, but also reduce the network loss and improve the voltage profile.

Interactions and consequences of inertia and switching costs

Purpose: Service research typically relates switching costs to customer loyalty, and portrays them as effective switching deterrents that engender harmful word-of-mouth (WOM). Rather than to customer loyalty, this paper aims to relate switching costs to consumer inertia, and show that while switching costs may result in customer retention, they can engender positive and negative WOM. This depends on whether the inertia stems from satisfaction or indifference. Design/methodology/approach: A mall-intercept survey investigated 518 customers' perceptions of their mobile phone service providers. Structural equation modelling fitted the data to the conceptual model. Findings: Switching costs deterred switching and engendered negative WOM, but only with low-inertia customers. With high-inertia customers, retention and WOM behaviours depended on whether the inertia stemmed from satisfaction or indifference. Satisfied customers with high switching costs tended to stay, gave more positive and less negative WOM. With indifferent customers, switching costs were unrelated to retention or WOM behaviours. Research limitations/implications: While they may be perceived negatively, switching costs can engender PWOM. Hence, research should not consider switching costs alone without considering the context that produces them. Practical implications: Service providers should segment their customers into low-inertia, high-inertia/satisfied and high-inertia/indifferent, and target each segment differently. By converting customers into the high-inertia/satisfied segment, service providers can make the best use of switching costs – not only in the traditional sense as a barrier to defection, but also as a way of generating positive WOM. Originality/value: This study is the first to consider the role of inertia with switching costs, positive WOM, and negative WOM. The findings suggest that past studies portraying switching costs as negative impediments that evoke only negative WOM might be misleading.

The Development of Competency Standards for Specialist Critical Care Nurses

In defining the contemporary role of the specialist nurse it is necessary to challenge the concept of nursing as merely a combination of skills and knowledge. Nursing must be demonstrated and defined in the context of client care and include the broader notions of professional development and competence. This qualitative study sought to identify the competency standards for nurse specialists in critical care and to articulate the differences between entry-to-practice standards and the advanced practice of specialist nurses. Over 800 hours of specialist critical care nursing practice were observed and grouped into 'domains' or major themes of specialist practice using a constant comparison qualitative technique. These domains were further refined to describe attributes of the registered nurses which resulted in effective and/or superior performance (competency standards) and to provide examples of performance (performance criteria) which met the defined standard. Constant comparison of the emerging domains, competency standards and performance criteria to observations of specialist critical care practice, ensured the results provided a true reflection of the specialist nursing role. Data analysis resulted in 20 competency standards grouped into six domains: professional practice, reflective practice, enabling, clinical problem solving, teamwork, and leadership. Each of these domains is comprised of between two and seven competency standards. Each standard is further divided into component parts or 'elements' and the elements are illustrated with performance criteria. The competency standards are currently being used in several Australian critical care educational programmes and are the foundation for an emerging critical care credentialling process. They have been viewed with interest by a variety of non-critical care specialty groups and may form a common precursor from which further specialist nursing practice assessment will evolve.