Continuing the critical analysis of 'meaningful relationships' in the context of the 'twin pillars'

This article continues the critical analysis of ‘meaningful relationships’ in the context of the operation of the ‘twin pillars’ which underpin the parenting provisions. It will be argued that the attitude of judicial officers to three key questions influence how they interpret this concept and consequently apply the best interest considerations. Relevant to this discussion is an examination of the Full Court’s approach to the key parenting sections, particularly the interaction of the primary and additional considerations. Against this backdrop, a current proposal to amend the ‘twin pillars’ will be examined.

Influences of green star rating tool on HVAC system design

Buildings are one of the most significant infrastructures in modern societies. The construction and operation of modern buildings consume a considerable amount of energy and materials, therefore contribute significantly to the climate change process. In order to reduce the environmental impact of buildings, various green building rating tools have been developed. In this paper, energy uses of the building sector in Australia and over the world are first reviewed. This is then followed by discussions on the development and scopes of various green building rating tools, with a particular focus on the Green Star rating scheme developed in Australia. It is shown that Green Star has significant implications on almost every aspect of the design of HVAC systems, including the selection of air handling and distribution systems, fluid handling systems, refrigeration systems, heat rejection systems and building control systems.

Bariatric patients and the use of mobile hoists : user experiences from three hospitals in South Australia

Nursing personnel are consistently identified as one of the occupational groups most at risk of work-related musculoskeletal disorders. During the moving and handling of bariatric patients, the weight of the patient combined with atypical body mass contributes to a significant risk of injury to the care provider and patient. This is further compounded by the shape, mobility and co-operation of the patient. The aim of this study was determine user experiences and design requirements for mobile hoists with bariatric patients. Structured interviews were conducted with six experienced injury management staff from the Manual Task Services department of three hospitals in Adelaide, South Australia. All staff had experience in patient handling, the use of patient handling equipment and the provision of patient handling training. A series of open-ended questions were structured around five main themes: 1) patient factors; 2) building/vehicle space and design; 3) equipment and furniture; 4) communication; and 5) staff issues. Questions focussed on the use of mobile hoists for lifting and transferring bariatric patients. Interviews were supplemented with a walk-through of the hospital to view the types of mobile hoists used, and the location and storage of equipment. Across the three hospitals there were differing classification systems to define bariatric patients. Ensuring patient dignity, respect and privacy were viewed as important in the management and rehabilitation of bariatric patients. Storage and space constraints were considered factors restricting the use of mobile floor hoists, with ceiling hoists being the preferred method for patient transfers. When using mobile floor hoists, the forces required to push, pull and manoeuvre, as well as sudden unstable movements of the hoist were considered important risks factors giving rise to a risk of injury to the care provider. Record keeping and purchasing policies appeared to inhibit the effective use of patient handling equipment. The moving and handling of bariatric patients presents complex and challenging issues. A co-ordinated and collaborative approach for moving and handling bariatric patients is needed across the range of care providers. Designers must consider both user and patient requirements.

Evaluation of the Hamilton Youth Court Pilot 2003-2005

Pilot Youth Courts were introduced at Hamilton Sheriff Court in June 2003 and at Airdrie Sheriff Court in June 2004. Although introduced as one of a number of measures aimed at responding more effectively to youth crime (including young people dealt with through the Children’s Hearings System), the Youth Courts were intended for young people who would otherwise have been dealt with in the adult Sheriff Summary Court. The objectives of the pilot Youth Courts were to: • reduce the frequency and seriousness of re-offending by 16 and 17 year old offenders, particularly persistent offenders (and some 15 year olds who are referred to the court); • promote the social inclusion, citizenship and personal responsibility of these young offenders while maximising their potential; • establish fast track procedures for those young persons appearing before the Youth Court; • enhance community safety, by reducing the harm caused to individual victims of crime and providing respite to those communities which are experiencing high levels of crime; and • test the viability and usefulness of a Youth Court using existing legislation and to demonstrate whether legislative and practical improvements might be appropriate. Evaluation of the Hamilton and Airdrie Sheriff Youth Court pilots suggested that they had been successful in meeting the objectives set for them by the Youth Court Feasibility Group. Both were tightly run courts that dealt with a heavy volume of business. The particular strengths of the Youth Court model over previous arrangements included the fast-tracking of young people to and through the court, the reduction in trials, the availability of a wider range of resources and services for young people and ongoing judicial review. The successful operation of the pilot Youth Courts was dependent upon effective teamwork among the relevant agencies and professionals concerned. Good information sharing, liaison and communication appeared to exist across agencies and the procedures that were in place to facilitate the sharing of information seemed to be working well. This was also facilitated by the presence of dedicated staff within agencies, resulting in clear channels of communication, and in the opportunity provided by the multi-agency Implementation Groups to identify and address operational issues on an ongoing basis. However, whether Youth Courts are required in Scotland or whether procedural improvement were possible in the absence of dedicated resources and personnel was more difficult to assess. Two issues in particular required further attention. First, consideration needed to be given to whether the Youth Courts should be more explicitly youth focused and what this might entail. Second, greater clarity was required regarding for whom the Youth Courts were intended. This suggested the need for further discussion of Youth Court targeting and its potential consequences among the various agencies concerned.

Community participation in the development of digital radio : the Australian experience

The participation of the community broadcasting sector in the development of digital radio provides a potentially valuable opportunity for non-market, end user-driven experimentation in the development of these new services in Australia. However this development path is constrained by various factors, some of which are specific to the community broadcasting sector and others that are generic to the broader media and communications policy, industrial and technological context. This paper filters recent developments in digital radio policy and implementation through the perspectives of community radio stakeholders, obtained through interviews, to describe and analyse these constraints. The early stage of digital community radio presented here is intended as a baseline for tracking the development of the sector as digital radio broadcasting develops. We also draw upon insights from scholarly debates about citizens media and participatory culture to identify and discuss two sets of opportunities for social benefit that are enabled by the inclusion of community radio in digital radio service development. The first arises from community broadcasting’s involvement in the propagation of the multi-literacies that drive new digital economies, not only through formal and informal multi- and trans-media training, but also in the ‘co-creative’ forms of collaborative and participatory media production that are fostered in the sector. The second arises from the fact that community radio is uniquely placed — indeed charged with the responsibility — to facilitate social participation in the design and operation of media institutions themselves, not just their service outputs.

The development of ground impact models for the analysis of the risks associated with Unmanned Aircraft Operations over inhabited areas

With the emergence of Unmanned Aircraft Systems (UAS) there is a growing need for safety standards and regulatory frameworks to manage the risks associated with their operations. The primary driver for airworthiness regulations (i.e., those governing the design, manufacture, maintenance and operation of UAS) are the risks presented to people in the regions overflown by the aircraft. Models characterising the nature of these risks are needed to inform the development of airworthiness regulations. The output from these models should include measures of the collective, individual and societal risk. A brief review of these measures is provided. Based on the review, it was determined that the model of the operation of an UAS over inhabited areas must be capable of describing the distribution of possible impact locations, given a failure at a particular point in the flight plan. Existing models either do not take the impact distribution into consideration, or propose complex and computationally expensive methods for its calculation. A computationally efficient approach for estimating the boundary (and in turn area) of the impact distribution for fixed wing unmanned aircraft is proposed. A series of geometric templates that approximate the impact distributions are derived using an empirical analysis of the results obtained from a 6-Degree of Freedom (6DoF) simulation. The impact distributions can be aggregated to provide impact footprint distributions for a range of generic phases of flight and missions. The maximum impact footprint areas obtained from the geometric template are shown to have a relative error of typically less than 1% compared to the areas calculated using the computationally more expensive 6DoF simulation. Computation times for the geometric models are on the order of one second or less, using a standard desktop computer. Future work includes characterising the distribution of impact locations within the footprint boundaries.

Governing teacher education : the case of teacher education in Australia

This paper analyses the attempted installation of the 1990 Australian Education Council commissioned report 'Teacher Education in Australia' (the Ebbeck Report), a document which proposed a radical reformulation and relative standardization of the content and structure of initial teacher education in Australia. The paper draws on Michel Foucault's concept of 'governmentality' to examine the discursive and technological dimensions of this programme of political rule. The paper makes apparent the 'microphysics of power' that were generated within, particularly, the Queensland educational community in the attempt to operationalise this report. Analysing educational policy from the perspective of 'government', the paper contends, directs attention to the conditions of operation of policy practices and reveals the dependence of educational policy on particular technical conditions of existence, routines and rituals of bureaucracy, forms of expertise and intellectual technologies, and the enlistment of agencies and authorities both within and outside the boundaries of the state.

Explicit, latent and meta-criteria : types of criteria at play in professional judgement practice

This paper engages with debates about whether comprehensive prior specification of criteria and standards is sufficient for informed professional judgement. A preoccupation has emerged with the specificity and explication of criteria intended to regulate judgement. This has resulted in criteria-compliance in the use of defined standards to validate judgements and improve reliability and consistency. Compliance has become a priority, the consequence being the prominence of explicit criteria, to the lack of acknowledgement of the operation of latent and meta-criteria within judgement practice. This paper examines judgement as a process involving three categories of assessment criteria in the context of standards-referenced systems: explicit, latent and meta-criteria. These are understood to be wholly interrelated and interdependent. A conceptualisation of judgement involving the interplay of the three criteria types is presented with an exploration of how they function to focus or alter assessments of quality in judgements of achievement in English and Mathematics.

Disability and the labour market : an analysis of British males

This paper attempts, using data from the British Labour Force Survey 1996, to examine to what extent differences in labour market outcomes between able-bodied and disabled men may be attributed to differences in endowments of human capital and associated productivity differences. Both labour force participation and selectivity corrected human capital equations are estimated and decomposition techniques applied to them. Using the methodology of Baldwin and Johnson [Baldwin, M., Johnson, W.G., 1994. Labor market discrimination against men with disabilities. Journal of Human Resources, XXIX(1), Winter, 1–19], the employment effects of wage discrimination against the disabled are also estimated. Evidence of both substantial wage and participation rate differences between able-bodied and disabled men are found, which have implications for the operation of the 1995 Disability Discrimination Act.

Measurements of particle emissions from nanotechnology processes, with assessment of measuring techniques and workplace controls

The overall aim of this project was to contribute to existing knowledge regarding methods for measuring characteristics of airborne nanoparticles and controlling occupational exposure to airborne nanoparticles, and to gather data on nanoparticle emission and transport in various workplaces. The scope of this study involved investigating the characteristics and behaviour of particles arising from the operation of six nanotechnology processes, subdivided into nine processes for measurement purposes. It did not include the toxicological evaluation of the aerosol and therefore, no direct conclusion was made regarding the health effects of exposure to these particles. Our research included real-time measurement of sub, and supermicrometre particle number and mass concentration, count median diameter, and alveolar deposited surface area using condensation particle counters, an optical particle counter, DustTrak photometer, scanning mobility particle sizer, and nanoparticle surface area monitor, respectively. Off-line particle analysis included scanning and transmission electron microscopy, energy-dispersive x-ray spectrometry, and thermal optical analysis of elemental carbon. Sources of fibrous and non-fibrous particles were included.

Performance evaluation of onsite sewage treatment : Evaluation of current research

Efficient management of domestic wastewater is a primary requirement for human well being. Failure to adequately address issues of wastewater collection, treatment and disposal can lead to adverse public health and environmental impacts. The increasing spread of urbanisation has led to the conversion of previously rural land into urban developments and the more intensive development of semi urban areas. However the provision of reticulated sewerage facilities has not kept pace with this expansion in urbanisation. This has resulted in a growing dependency on onsite sewage treatment. Though considered only as a temporary measure in the past, these systems are now considered as the most cost effective option and have become a permanent feature in some urban areas. This report is the first of a series of reports to be produced and is the outcome of a research project initiated by the Brisbane City Council. The primary objective of the research undertaken was to relate the treatment performance of onsite sewage treatment systems with soil conditions at site, with the emphasis being on septic tanks. This report consists of a ‘state of the art’ review of research undertaken in the arena of onsite sewage treatment. The evaluation of research brings together significant work undertaken locally and overseas. It focuses mainly on septic tanks in keeping with the primary objectives of the project. This report has acted as the springboard for the later field investigations and analysis undertaken as part of the project. Septic tanks still continue to be used widely due to their simplicity and low cost. Generally the treatment performance of septic tanks can be highly variable due to numerous factors, but a properly designed, operated and maintained septic tank can produce effluent of satisfactory quality. The reduction of hydraulic surges from washing machines and dishwashers, regular removal of accumulated septage and the elimination of harmful chemicals are some of the practices that can improve system performance considerably. The relative advantages of multi chamber over single chamber septic tanks is an issue that needs to be resolved in view of the conflicting research outcomes. In recent years, aerobic wastewater treatment systems (AWTS) have been gaining in popularity. This can be mainly attributed to the desire to avoid subsurface effluent disposal, which is the main cause of septic tank failure. The use of aerobic processes for treatment of wastewater and the disinfection of effluent prior to disposal is capable of producing effluent of a quality suitable for surface disposal. However the field performance of these has been disappointing. A significant number of these systems do not perform to stipulated standards and quality can be highly variable. This is primarily due to houseowner neglect or ignorance of correct operational and maintenance procedures. The other problems include greater susceptibility to shock loadings and sludge bulking. As identified in literature a number of design features can also contribute to this wide variation in quality. The other treatment processes in common use are the various types of filter systems. These include intermittent and recirculating sand filters. These systems too have their inherent advantages and disadvantages. Furthermore as in the case of aerobic systems, their performance is very much dependent on individual houseowner operation and maintenance practices. In recent years the use of biofilters has attracted research interest and particularly the use of peat. High removal rates of various wastewater pollutants have been reported in research literature. Despite these satisfactory results, leachate from peat has been reported in various studies. This is an issue that needs further investigations and as such biofilters can still be considered to be in the experimental stage. The use of other filter media such as absorbent plastic and bark has also been reported in literature. The safe and hygienic disposal of treated effluent is a matter of concern in the case of onsite sewage treatment. Subsurface disposal is the most common and the only option in the case of septic tank treatment. Soil is an excellent treatment medium if suitable conditions are present. The processes of sorption, filtration and oxidation can remove the various wastewater pollutants. The subsurface characteristics of the disposal area are among the most important parameters governing process performance. Therefore it is important that the soil and topographic conditions are taken into consideration in the design of the soil absorption system. Seepage trenches and beds are the common systems in use. Seepage pits or chambers can be used where subsurface conditions warrant, whilst above grade mounds have been recommended for a variety of difficult site conditions. All these systems have their inherent advantages and disadvantages and the preferable soil absorption system should be selected based on site characteristics. The use of gravel as in-fill for beds and trenches is open to question. It does not contribute to effluent treatment and has been shown to reduce the effective infiltrative surface area. This is due to physical obstruction and the migration of fines entrained in the gravel, into the soil matrix. The surface application of effluent is coming into increasing use with the advent of aerobic treatment systems. This has the advantage that treatment is undertaken on the upper soil horizons, which is chemically and biologically the most effective in effluent renovation. Numerous research studies have demonstrated the feasibility of this practice. However the overriding criteria is the quality of the effluent. It has to be of exceptionally good quality in order to ensure that there are no resulting public health impacts due to aerosol drift. This essentially is the main issue of concern, due to the unreliability of the effluent quality from aerobic systems. Secondly, it has also been found that most householders do not take adequate care in the operation of spray irrigation systems or in the maintenance of the irrigation area. Under these circumstances surface disposal of effluent should be approached with caution and would require appropriate householder education and stringent compliance requirements. However despite all this, the efficiency with which the process is undertaken will ultimately rest with the individual householder and this is where most concern rests. Greywater too should require similar considerations. Surface irrigation of greywater is currently being permitted in a number of local authority jurisdictions in Queensland. Considering the fact that greywater constitutes the largest fraction of the total wastewater generated in a household, it could be considered to be a potential resource. Unfortunately in most circumstances the only pretreatment that is required to be undertaken prior to reuse is the removal of oil and grease. This is an issue of concern as greywater can considered to be a weak to medium sewage as it contains primary pollutants such as BOD material and nutrients and may also include microbial contamination. Therefore its use for surface irrigation can pose a potential health risk. This is further compounded by the fact that most householders are unaware of the potential adverse impacts of indiscriminate greywater reuse. As in the case of blackwater effluent reuse, there have been suggestions that greywater should also be subjected to stringent guidelines. Under these circumstances the surface application of any wastewater requires careful consideration. The other option available for the disposal effluent is the use of evaporation systems. The use of evapotranspiration systems has been covered in this report. Research has shown that these systems are susceptible to a number of factors and in particular to climatic conditions. As such their applicability is location specific. Also the design of systems based solely on evapotranspiration is questionable. In order to ensure more reliability, the systems should be designed to include soil absorption. The successful use of these systems for intermittent usage has been noted in literature. Taking into consideration the issues discussed above, subsurface disposal of effluent is the safest under most conditions. This is provided the facility has been designed to accommodate site conditions. The main problem associated with subsurface disposal is the formation of a clogging mat on the infiltrative surfaces. Due to the formation of the clogging mat, the capacity of the soil to handle effluent is no longer governed by the soil’s hydraulic conductivity as measured by the percolation test, but rather by the infiltration rate through the clogged zone. The characteristics of the clogging mat have been shown to be influenced by various soil and effluent characteristics. Secondly, the mechanisms of clogging mat formation have been found to be influenced by various physical, chemical and biological processes. Biological clogging is the most common process taking place and occurs due to bacterial growth or its by-products reducing the soil pore diameters. Biological clogging is generally associated with anaerobic conditions. The formation of the clogging mat provides significant benefits. It acts as an efficient filter for the removal of microorganisms. Also as the clogging mat increases the hydraulic impedance to flow, unsaturated flow conditions will occur below the mat. This permits greater contact between effluent and soil particles thereby enhancing the purification process. This is particularly important in the case of highly permeable soils. However the adverse impacts of the clogging mat formation cannot be ignored as they can lead to significant reduction in the infiltration rate. This in fact is the most common cause of soil absorption systems failure. As the formation of the clogging mat is inevitable, it is important to ensure that it does not impede effluent infiltration beyond tolerable limits. Various strategies have been investigated to either control clogging mat formation or to remediate its severity. Intermittent dosing of effluent is one such strategy that has attracted considerable attention. Research conclusions with regard to short duration time intervals are contradictory. It has been claimed that the intermittent rest periods would result in the aerobic decomposition of the clogging mat leading to a subsequent increase in the infiltration rate. Contrary to this, it has also been claimed that short duration rest periods are insufficient to completely decompose the clogging mat, and the intermediate by-products that form as a result of aerobic processes would in fact lead to even more severe clogging. It has been further recommended that the rest periods should be much longer and should be in the range of about six months. This entails the provision of a second and alternating seepage bed. The other concepts that have been investigated are the design of the bed to meet the equilibrium infiltration rate that would eventuate after clogging mat formation; improved geometry such as the use of seepage trenches instead of beds; serial instead of parallel effluent distribution and low pressure dosing of effluent. The use of physical measures such as oxidation with hydrogen peroxide and replacement of the infiltration surface have been shown to be only of short-term benefit. Another issue of importance is the degree of pretreatment that should be provided to the effluent prior to subsurface application and the influence exerted by pollutant loadings on the clogging mat formation. Laboratory studies have shown that the total mass loadings of BOD and suspended solids are important factors in the formation of the clogging mat. It has also been found that the nature of the suspended solids is also an important factor. The finer particles from extended aeration systems when compared to those from septic tanks will penetrate deeper into the soil and hence will ultimately cause a more dense clogging mat. However the importance of improved pretreatment in clogging mat formation may need to be qualified in view of other research studies. It has also shown that effluent quality may be a factor in the case of highly permeable soils but this may not be the case with fine structured soils. The ultimate test of onsite sewage treatment system efficiency rests with the final disposal of effluent. The implication of system failure as evidenced from the surface ponding of effluent or the seepage of contaminants into the groundwater can be very serious as it can lead to environmental and public health impacts. Significant microbial contamination of surface and groundwater has been attributed to septic tank effluent. There are a number of documented instances of septic tank related waterborne disease outbreaks affecting large numbers of people. In a recent incident, the local authority was found liable for an outbreak of viral hepatitis A and not the individual septic tank owners as no action had been taken to remedy septic tank failure. This illustrates the responsibility placed on local authorities in terms of ensuring the proper operation of onsite sewage treatment systems. Even a properly functioning soil absorption system is only capable of removing phosphorus and microorganisms. The nitrogen remaining after plant uptake will not be retained in the soil column, but will instead gradually seep into the groundwater as nitrate. Conditions for nitrogen removal by denitrification are not generally present in a soil absorption bed. Dilution by groundwater is the only treatment available for reducing the nitrogen concentration to specified levels. Therefore based on subsurface conditions, this essentially entails a maximum allowable concentration of septic tanks in a given area. Unfortunately nitrogen is not the only wastewater pollutant of concern. Relatively long survival times and travel distances have been noted for microorganisms originating from soil absorption systems. This is likely to happen if saturated conditions persist under the soil absorption bed or due to surface runoff of effluent as a result of system failure. Soils have a finite capacity for the removal of phosphorus. Once this capacity is exceeded, phosphorus too will seep into the groundwater. The relatively high mobility of phosphorus in sandy soils have been noted in the literature. These issues have serious implications in the design and siting of soil absorption systems. It is not only important to ensure that the system design is based on subsurface conditions but also the density of these systems in given areas is a critical issue. This essentially involves the adoption of a land capability approach to determine the limitations of an individual site for onsite sewage disposal. The most limiting factor at a particular site would determine the overall capability classification for that site which would also dictate the type of effluent disposal method to be adopted.

The extent of the insured’s duty of disclosure : a comparative analysis of the disclosure obligations of insured in Australia, Singapore and China

Pre-contractual material disclosure and representation from an insurance policy proposer is the most important element for insurers to make a decision on whether a proposer is insurable and what are the terms and conditions if the proposal by the proposer is able to be insured. The issue this thesis researches and investigates focus on the issues related to the pre-contractual non-disclosures and misrepresentations of an insured under the principle of utmost good faith, by operation of laws, can achieve with different results in different jurisdiction. A similar disputed claim involving material non-disclosed personal information or misrepresentation at the pre-contractual stage from an insured with respect to both general and life insurance policies settled by an insurer in Australia could be that the policy is set aside ab initio by the insurers in Singapore or China. The jurisdictions this thesis examines are • Australia; • Singapore; and • China including Hong Kong.

Learning processes in creative industries initiatives in developing countries : an examination of policy and practice

What does a dance group in Benin that mixes contemporary and ethnic dancing have in common with Mongolian felt producers that want to enter the design market in Europe? These are both examples of learning processes in Creative Industries initiatives in developing countries. Following the concept of sustainable development, I argue that the challenge for developing countries in contemporary society is to meet the very real need of people for economic development and opportunities for income generation, while at the same time avoiding unintended and unwanted consequences of economic development and globalisation. The concept of the Creative Industries may be a way to promote a development that is sustainable and avoids social exclusion of groups-at-risk. In line with this, I argue that the Creative Industries sector could, in fact, link economic development and the continuation and evolution of local traditions and cultural heritage. A pressing question then is: how can education and learning contribute to creating a context in which talent can flourish? This study aims to provide a comprehensive analysis of the research problem of this thesis: what elements are conducive for individual learning processes in creative development initiatives? In this, I argue that it is crucial to determine what ingredients and characteristics contribute to making these initiatives successful, that is, to meet their specific goals, in a developing context. This is explored through a staged analysis: an overview of quantitative data, an inventory and comparative case studies and, finally, the description and analysis of two in-depth case studies – felt design in Mongolia (Asia) and dance in Benin (Africa), in which I was an observer of the action phase of the local interventions. The analysis culminates in practice-related outcomes related to the operation of creative development initiatives, as well as the contribution to the academic debate on issues like the cultural gap between developed and developing countries, transformative learning and the connection of learning spaces.

Paradoxes of participation : non-union workplace partnerships in John Lewis

The extent to which workplace partnership delivers mutual gains is subject to considerable debate amongst practitioners and scholars. One of the oldest and largest examples of workplace partnership is the John Lewis Partnership that began using forms of non-union employee representation in 1929. Despite ongoing interest from researchers in employee representation, and specifically non-union forms of employee voice, there have been few in-depth studies of the Partnership's organisational structure and practices since the 1980s. This paper explores in detail the operation of representation structures in the John Lewis Partnership, which is a significant case of non-union workplace partnership with the potential for mutual gains. A key finding of the paper was that the decision-making structures that characterise the Partnership, and that are protected by a constitution, are under constant threat from the discursive struggle to define partnership in a way that privileges managerial interests. The paper argues, therefore, that mutual gains need to be secured both structurally and discursively to address the tensions and paradoxes at the heart of debates about the meaning and aims of employee representation.

The high price of hesitation where time of the essence

The decision of Lai v Soineva [2011] QSC 247 in relation to the operation of standard conditions in the Queensland REIQ contract highlights a very practical issue often overlooked in the heat of a transaction .The point is relatively simple. In this instance ,the case concerned the interpretation of the printed "Building and Pest Inspection Clause" but is of relevance to the printed "Finance Clause" in the same contract as the wording and principles are identical. It highlights the issue of knowing well what is in the standard contract and not making assumptions. The case also highlights the cost to a party of dithering in making an election in a time of the essence environment