Transport Barkhausen-like noise in uniaxially pressed Bi(1.65)Pb(0.35)Sr(2)Ca(2)Cu(3)O(10+delta) ceramic samples

We report on the detection of the transport Barkhausen-like noise (TBN) in polycrystalline samples of Bi(1.65)Pb(0.35)Sr(2)Ca(2) Cu(3)O(10+delta) (Bi-2223) which were subjected to different uniaxial compacting pressures. The transport Barkhausen-like noise was measured when the sample was subjected to an ac triangular-shape magnetic field (f similar to 1 Hz) with maximum amplitude B(max) approximate to 5.5 mT, in order to avoid the flux penetration within the superconducting grains. Analysis of the TBN signal, measured for several values of excitation current density, indicated that the applied magnetic field in which the noise signal first appears, B(a)(t(i)), is closely related to the magnetic-flux pinning capability of the material. The combined results are consistent with the existence of three different superconducting levels within the samples: (i) the superconducting grains; (ii) the superconducting clusters; and (iii) the weak-links. We finally argue that TBN measurements constitute a powerful tool for probing features of the intergranular transport properties in polycrystalline samples of high-T(c) superconductors. (C) 2010 Elsevier B.V. All rights reserved.

Montmorillonite/carbon nanocomposites prepared from sucrose for catalytic applications

Sucrose was used to prepare montmorillonite/carbon nanocomposites by calcination in a reduced atmosphere. The aim was to investigate the changes derived from varying the clay and sucrose content in the resulting material and to change the adsorption properties to evaluate its potential to be used in catalytic applications. X-ray diffraction patterns revealed the formation of an intercalated nanostructure composed of carbon-filled clay mineral layers, which was confirmed by the Fourier transform infrared spectra and thermogravimetry curves. Differences in composition and texture surface were detected by scanning electron microscopy images and were supported by viscosity measurements. These measurements were helpful in understanding why the sample prepared with the highest sucrose content presented the lowest gasoline and methylene blue adsorption results and why the highest adsorption properties were attributed to the sample with the highest clay content. Moreover, BET and BJH studies allowed understanding oleic acid catalytic conversion. Finally, a water flux simulation test was performed to determine the mechanical resistance in comparison to an activated carbon. It was found that the nanocomposites were more resistant, supporting their use in catalytic applications for a longer period of time. (C) 2011 Elsevier B.V. All rights reserved.

Surface modification of bovine bone ash prepared by milling and acid washing process

Bovine bone ash is the main raw material for fabrication of bone china, a special kind of porcelain that has visual and mechanical advantages when compared to usual porcelains. The properties of bone china are highly dependent on the characteristics of the bone ash. However, despite a relatively common product, the science behind formulations and accepted fabrication procedures for bone china is not completely understood and deserves attention for future processing optimizations. In this paper, the influence of the preparation steps (firing, milling, and washing of the bones) on the physicochemical properties of bone ash particles was investigated. Bone powders heat-treated at temperatures varying from 700 to 1000 degrees C were washed and milled. The obtained materials were analyzed in terms of particle size distribution, chemical composition, density, specific surface area, FTIR spectroscopy, dynamic electrophoretic mobility, crystalline phases and scanning electron microscopy. The results indicated that bone ash does not significantly change in terms of chemistry and physical features at calcination temperatures above 700 degrees C. After washing in special conditions, one could only observe hydroxyapatite in the diffraction pattern. By FTIR it was observed that carbonate seems to be mainly concentrated on the surface of the powders. Since this compound can influence in the dispersion stability, and consequently in the quality of the final bone china product, and considering optimal washing parameters based on the dynamic electrophoretic mobility results, we describe a procedure for surface cleaning. (c) 2009 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Carbide lime and industrial hydrated lime characterization

This paper focuses on the characterization of carbide lime (CL) - a by-product of acetylene production, composed mainly of calcium hydroxide with minor parts of carbonate - and compares its features to those of ""dry"" hydrated lime (HL) commonly used as a building material. Chemical, thermogravimetric and X-ray diffraction analyses indicated that the limes are similar in chemical and mineralogical compositions. except for the presence of carbon in the waste. Morphological and elemental chemical analyses by SEM and EDS revealed that CL particles differ from HL ones in their morphology and by the presence of carbon formations, Physical characterization included density and BET surface area of the materials. as well as, their particle size distributions in deionized water at diverse time periods. CL underwent agglomeration after approximately 60 min in water, whereas HL progressively became finer with time as determined by laser diffraction. In addition, water retention and squeeze flow tests were used to assess the pastes` fresh properties. (c) 2009 Elsevier B.V. All rights reserved.

KDP/PEDOT: PSS mixture as a new alternative in the fabrication of pressure sensing devices

In this work we studied the mixture of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS), a commercial polymer, with monobasic potassium phosphate (KDP), a piezoelectric salt, as a possible novel material in the fabrication of a low cost, easy-to-make,flexible pressure sensing device. The mixture between KDP and PEDOT: PSS was painted in a flexible polyester substrate and dried. Afterwards, I x V curves were carried out. The samples containing KDP presented higher values of current in smaller voltages than the PEDOT: PSS without KDP. This can mean a change in the chain arrays. Other results showed that the material responds to directly applied pressure to the sample that can be useful to sensors fabrication. (c) 2008 Elsevier B.V. All rights reserved.

Traceability system in cod fishing

The objective of this research was to examine how various factors in Icelandic cod fishing can influence the quality of the raw material, using traceability systems to link these factors, and how transfer that knowledge and techniques to the Brazilian seafood industry. Data were collected in 2007 and analysed, to find a functional relationship between various quality factors. The analysis, showed, that there is a correlation between the number of parasites in the fillets and location of the fishing ground. It also showed that fishing ground and volume in haul can influence gaping, and that fillet yield differs between fishing grounds. These conclusions could only be drawn because of the ability to trace the fish from catch and all the way through processing. Recommendations drawn from this research to the Brazilian Competent Authority are to revise the countries fisheries legislation in order to enable the implementation of a traceability system that could be used as a tool to improve the quality of the raw material. (C) 2010 Elsevier Ltd. All rights reserved.

New approaches to underground systems in Brazilian Smilax species (Smilacaceae)

MARTINS, A. R. (Institute of Biology, State University of Campinas - UNICAMP, 13083-970, Campinas, SP, Brazil), N. PUT, (Division of Biology and Education, University of Vechta, 49377 Vechta, Germany), A. N. SOARES, A.B BOMB, and B. APPEZZATO DA GLORIA (Biological Science Department, Escola Superior de Agricultura `Luiz de Queiroz`, University of Sao Paulo, 13418-900, Piracicaba, SP, Brazil). J. Torrey Bot. Soc. 137: 220-235. 2010.-New approaches to underground systems in Brazilian Smilax species (Smilacaceae). Scientific studies show that the watery extract of the thickened underground stem and its adventitious roots of the genus Smilax can act as a therapeutic agent in immunoinflammatory disorders, such as rheumatic arthritis. Brazilians have used this genus of plants in folk medicine, however it is very hard to identify these species, since the morphology of the underground systems is very similar in this group. For better identification of those systems, we studied six species of Smilax L. (S. brasiliensis, S. campestris, S. cissoides, S. goyazana, S. oblongifolia and S. rufescens), collected in different regions of Brazil with different physiognomies and soil characteristics. The main purpose is to describe the morpho-anatomy of the underground systems and to analyze if their structure depends on environmental conditions. The underground stem (rhizophore) is of brown color and it is knotty, massive, slender (S. rufescens) or tuberous (S. brasiliensis, S. campestris, S. cissoides, S. goyazana and S. oblongifolia). The tuberization is a result of primary thickened meristem (PTM) activity. The color and thickness of the adventitious roots change during development because the epidermis and outer cortex are disposed of, so the inner cortex becomes the new covering tissue with lignified and dark color cells. There are differences in starch grain shapes in mature roots. The chemical attributes of the soil are very similar in all studied environments and, even when soil characteristics varied, all the species` underground system was distributed close to the soil surface (10 to 15 cm deep). The species exhibited clonal growth hence their underground system functions as storage structures and the axillary buds can sprout into new stems. Only Smilax rufescens, collected in sandy soil of Restinga, has vegetative dispersal due to the runners.

Evaluation of two round baling systems for harvesting understory biomass

The objective of this study was to evaluate the performance and to estimate costs of two round baling systems for harvesting understory biomass. One system was a cutter-shredderbaler prototype (Bio-baler). The other system required two successive operations. The first operation was cutting and shredding with a Supertrak tractor equipped with a Fecon mulcher head. The second operation was baling with a Claas baler. The machines were evaluated in three different pine stands on the Osceola National Forest in Florida, United States. Data collection included time study, fuel consumption and bale measurements. Material was collected from a sample of bales for heat and moisture content determination. On the most representative site (Site 2), the Bio-baler recovered 8.05 green t ha(-1) while the mulcher and the Claas baler recovered 9.75 green t ha(-1) (43 and 52 percent of original understory biomass, respectively). Productivity was 0.30 ha h(-1) for the Bio-baler and 0.51 ha h(-1) for the Claas baler. Density of the bales was 321 green kg m(-3) for the Bio-baler and 373 green kg m(-3) for the Claas baler. Average net heat content was 6263 MJ bale(-1) for the Bio-baler and 6695 MJ bale(-1) for the Claas baler with biomass containing 38 percent of moisture content on a wet basis. cost per unit area was less with the Bio-baler (US$320.91 ha(-1)) than with the mulcher-baler system (US$336.62-US$596.77 ha(-1)). Published by Elsevier Ltd.

NEW PHYTOSEIIDAE (ACARI: MESOSTIGMATA) FROM COSTA RICA, WITH ADDITIONAL INFORMATION ON OTHER SPECIES

This paper reports on a study of phytoseiids collected from the La Selva Biological Field Station, the ALAS (Arthropods of La Selva) Project, made available to us by the Canadian National Collection via Dr. E. E. Lindquist. This material includes two new species, Proprioseiopsis versus n. sp. and Transeius costarricensis n. sp., three new records for Central America, and additional information for nine species previously reported from La Selva.

Emergy synthesis of intensive eucalyptus cultivation in Sao Paolo, Brazil

We used environmental accounting to evaluate high-intensity clonal eucalyptus production in Sao Paolo, Brazil, converting inputs (environmental, material, and labor) to emergy units so ecological efficiency could be compared on a common basis. Input data were compiled under three pH management scenarios (lime, ash, and sludge). The dominant emergy input is environmental work (transpired water, similar to 58% of total emergy), followed by diesel (similar to 15%); most purchased emergy is invested during harvest (41.8% of 7-year production totals). Where recycled materials are used for pH amendment (ash or sludge instead of lime), we observe marked improvements in ecological efficiency; lime (raw) yielded the highest unit emergy value (UEV = emergy per unit energy in the product = 9.6E + 03 sej J(-1)), whereas using sludge and ash (recycled) reduced the UEV to 8.9E + 03 and 8.8E + 03 sej J(-1), respectively. The emergy yield ratio was similarly affected, suggesting better ecological return on energy invested. Sensitivity of resource use to other operational modifications (e.g., decreased diesel, labor, or agrochemicals) was small (<3% change). Emergy synthesis permits comparison of sustainability among forest production systems globally. This eucalyptus scheme shows the highest ecological efficiency of analyzed pulp production operations (UEV range = 1.1 to 3.6E + 04 sej J(-1)) despite high operational intensity.

`Swingle` citrumelo propagation by cuttings for citrus nursery tree production or inarching

`Swingle` citrumelo [Citrus paradisi MacFaden x Poncirus trifoliata (L.) Raf.] has been extensively used as a rootstock in several citrus growing regions of the World, including Southern Brazil where `Rangpur` lime (Citrus limonia Osbeck) is still the predominant variety despite being affected by several important pathogens. in this case, `Swingle` citrumelo is used to produce nursery trees to establish new orchards or to be inarched in adult and healthy groves in order to change the rootstock. We report herein a system to produce trees on `Swingle` citrumelo more rapidly by budding onto non-rooted cuttings, as well as assessing potential to rapidly multiply `Swingle` through rooting of non-budded cuttings. Therefore, two potential products are described: budded trees and rooted rootstock cuttings. `Valencia` sweet orange [Citrus sinensis (L.) Osbeck] was budded at different heights on cuttings derived from eight-month old rootstocks. Grafted and additional non-budded cuttings were then treated with indole-3-butyric acid (500 mg L(-1)) or left untreated before rooting. Three types of cuttings were evaluated: softwood, semi-hardwood and hardwood. The use of nursery trees derived from pre-budded hardwood cuttings of `Swingle` citrumelo is an alternative grafting method on this cultivar. Softwood cuttings with one leaf pair were considered the most adequate material for rapid multiplication of `Swingle` citrumelo by cutting. This could be particularly useful for inarching production or conventional budding after transplant of cutting-derived rootstocks. (C) 2008 Elsevier B.V. All rights reserved.

Particle size and concentration of poly(epsilon-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures

The objective of this study was to evaluate the effect of particle size and concentration of poly(F.-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures, comparing it with polyethylene under the same experimental conditions. Two soil types were used: a Kandiudalfic Eutrudox with a clayey texture and an Arenic Hapludult with a sandy texture. The two different plastic specimens were incorporated in the form of plastic films with three increasing particle sizes and six doses, from 0 to 2.5 mg C g(-1) soil. Each plastic dose was incorporated into 200 g of soil placed in a hermetically closed jar at 28 degrees C, and incubated for a 120-day period to determine CO(2) evolution. Once again it was confirmed that polyethylene is almost non-biodegradable, in contrast to PCL/S, which can be defined as a biodegradable material. Soil texture affected the mineralization kinetics of the plastic specimens, with higher values for the clayey soil. No changes in soil microbial biomass-C or -N were observed by adding polyethylene and PCL/S to the soil. Also, no significant differences were observed on seed emergence and development of rice seedlings (Oryza sativa L.) in plastic modified soil. (C) 2009 Elsevier Ltd. All rights reserved.

Characterization of humic substances in salt marsh soils under sea rush (Juncus maritimus)

Humic substances (HS) from salt marsh soils were characterized and the relationships among HS composition and some geochemical factors were analysed. For this, three salt marshes with the same vegetation cover (Juncus maritimus), but with different geochemical characteristics, were selected. The qualitative characterization of the soil humic acids and fulvic acids was carried out by elemental analysis, FTIR spectroscopy, fluorescence spectroscopy and VACP/MAS (13)C NMR spectroscopy. HS from salt marsh soils under sea rush (Juncus maritimus) displayed some shared characteristics such as low degree of humification, low aromatic content and high proportion of labile compounds, mainly polysaccharides and proteins. However, although the three salt marsh soils under study were covered by the same type of vegetation, the HS showed some important differences. HS composition was found to be determined not only by the nature of the original organic material, but also by environmental factors such as soil texture, redox conditions and tidal influence. In general. an increase in the humification process appeared to be related to aerobic conditions and predominance of sand in the mineral fraction of the soil, while the preservation of labile organic compounds may be associated with low redox potential values and fine soil texture. (C) 2008 Elsevier Ltd. All rights reserved.

Isoflavones and Antioxidant Capacity of Commercial Soy-Based Beverages: Effect of Storage

Samples of 11 different brands of commercially available soy-based beverages (n = 65), including products made from soy protein isolate (SPI) and soy milk, mixed with fruit juice and/or flavoring, were analyzed for their isoflavone content and in vitro antioxidant activity. There was a large variation in isoflavone and total phenolics contents ranging from 0.7 to 13 mg of isoflavones/200 mL and from 6 to 155 mg equivalents of catechin/200 mL, respectively. The antioxidant activity also varied significantly among products. Storage of the beverages at room temperature caused a significant decrease of antioxidant capacity, soluble phenolics, and isoflavone contents after 9 months. When soybeans used for beverage production were stored for up to 6 months in silos, the resulting products were not affected. However, a decrease of malonyl and a proportional increase of free glucosidic forms of isoflavones were observed after storage of both the raw material and the beverages.

Electron beam irradiation of Matricaria chamomilla L. for microbial decontamination

Wild chamomile (Matricaria chamomilla L.) is one of the most popular herbal materials with both internal and external use to cure different health disturbances. As a consequence of its origin, chamomile could carry various microbial contaminants which offer different hazards to the final consumer. Reduction of the microbial load to the in force regulation limits represents an important phase in the technological process of vegetal materials, and the electron beam treatment might be an efficient alternative to the classical methods of hygienic quality assurance. The purpose of the study was to analyze the potential application of the electron beam treatment in order to assure the microbial safety of the wild chamomile. Samples of chamomile dry inflorescences were treated in electron beam (e-beam) of 6 MeV mean energy, at room temperature and ambient pressure. Some loss of the chemical compounds with bioactive role could be noticed, but the number of microorganisms decreased as a function on the absorbed dose. Consequently, the microbial quality of studied vegetal material inflorescences was improved by e-beam. irradiation. (C) 2008 Elsevier B.V. All rights reserved.