Recovery of protein from discharged wastewater during the production of chitin

Studies were carried out to optimize the conditions for the recovery of protein. The results showed that pH of 6.00 for wastewater, the dosage of 1% chitosan solution in 1% acetic acid aqueous solution of 2.0 ml for 50 ml wastewater and 1% FeCl3 aqueous solution of 2 ml for 50 ml wastewater, the flocculation time of 4.0 h were the optimal conditions for the recovery of protein. The obtained protein sediment contained abundant amino acids, especially isoleucine, methione and lysine that are absent in other protein resource. (c) 2007 Elsevier Ltd. All rights reserved.

Light energy conversion into H-2 by Anabaena variabilis mutant PK84 dense cultures exposed to nitrogen limitations

Concentrated cultures (25-86 mg Chl a l(-1)) of Anabaena variabilis PK84 were incubated under 99% Ar+1% CO2 atmosphere in the photobioreactor made of coaxial cylinders. Under illumination equal to 353 mu E m(-2) s(-1) they produced hydrogen with the rate more than 20 ml l(-1) h(-1) for several days. The efficiency of light energy conversion into H-2 was approx. 1% and did not depend significantly on initial Chl a concentration. H-2/O-2 ratio reached 41.5% of theoretical value for water photolysis. Data indicate that dense cultures might be used for outdoor systems under direct sun light. Supra-optimal temperatures 36 degrees C were not harmful for cultures even for 2 days period. Short-term incubation of cultures under 36 degrees C even increased H2 production rate and efficiency of light energy bioconversion by 1.25 times. (c) 2006 International Association for Hydrogen Energy. Published by Elsevier Ltd. All rights reserved.

二氧化碳在孔隙咸水层中多相流动数值模拟研究

There has been a growing concern about the use of fossil fuels and its adverse effects on the atmospheric greenhouse and ecological environment. A reduction in the release rate of CO2 into the atmosphere poses a major challenge to the land ecology of China. The most promising way of achieving CO2 reduction is to dispose of CO2 in deep saline aquifers. Deep aquifers have a large potential for CO2 sequestration in geological medium in terms of volume and duration. Through the numerical simulation of multiphase flow in a porous media, the transformation and motion of CO2 in saline aquifers has been implemented under various temperature and hydrostatic pressure conditions, which plays an important role to the assessment of the reliability and safety of CO2 geological storage. As expected, the calculated results can provide meaningful and scientific information for management purposes. The key problem to the numerical simulation of multiphase flow in a porous media is to accurately capture the mass interface and to deal with the geological heterogeneity. In this study, the updated CE/SE (Space and time conservation element and solution element) method has been proposed, and the Hybrid Particle Level Set method (HPLS) has extended for multiphase flows in porous medium, which can accurately trace the transformation of the mass interface. The benchmark problems have been applied to evaluate and validate the proposed method. In this study, the reliability of CO2 storage in saline aquifers in Daqingzi oil field in Sunlong basin has been discussed. The simulation code developed in this study takes into account the state for CO2 covering the triple point temperature and pressure to the supercritical region. The geological heterogeneity has been implemented, using the well known geostatistical model (GSLIB) on the base of the hard data. The 2D and 3D model have been set up to simulate the CO2 multiphase flow in the porous saline aquifer, applying the CE/SE method and the HPLS method .The main contents and results are summarized as followings. (1) The 2D CE/SE method with first and second –order accuracy has been extended to simulate the multiphase flow in porous medium, which takes into account the contribution of source and sink in the momentum equation. The 3D CE/SE method with the first accuracy has been deduced. The accuracy and efficiency of the proposed CE/SE method have been investigated, using the benchmark problems. (2) The hybrid particle level set method has been made appropriate and extended for capturing the mass interface of multiphase flows in porous media, and the numerical method for level set function calculated has been formulated. (3) The closed equations for multiphase flow in porous medium has been developed, adept to both the Darcy flow and non-Darcy flow, getting over the limitation of Reynolds number to the calculation. It is found that Darcy number has a decisive influence on pressure as well as velocity given the Darcy number. (4) The new Euler scheme for numerical simulations of multiphase flows in porous medium has been proposed, which is efficient and can accurately capture the mass interface. The artificial compressibility method has been used to couple the velocities and pressure. It is found that the Darcy number has determinant effects on the numerical convergence and stability. In terms of the different Darcy numbers, the coefficient of artificial compressibility and the time step have been obtained. (5) The time scale of the critical instability for critical CO2 in the saline aquifer has been found, which is comparable with that of completely CO2 dissolved saline aquifer. (6) The concept model for CO2 multiphase flows in the saline aquifer has been configured, based on the temperature, pressure, porosity as well as permeability of the field site .Numerical simulation of CO2 hydrodynamic trapping in saline aquifers has been performed, applying the proposed CE/SE method. The state for CO2 has been employed to take into account realistic reservoir conditions for CO2 geological sequestration. The geological heterogeneity has been sufficiently treated , using the geostatistical model. (7) It is found that the Rayleigh-Taylor instability phenomenon, which is associated with the penetration of saline fluid into CO2 fluid in the direction of gravity, has been observed in CO2 multiphase flows in the saline aquifer. Development of a mushroom-type spike is a strong indication of the formation of Kelvin-Helmholtz instability due to the developed short wavelength perturbations present along the interface and parallel to the bulk flow. Additional key findings: the geological heterogeneity can distort the flow convection. The ascending of CO2 can induce the persistent flow cycling effects. The results show that boundary conditions of the field site have determinant effects on the transformation and motion of CO2 in saline aquifers. It is confirmed that the proposed method and numerical model has the reliability to simulate the process of the hydrodynamic trapping, which is the controlling mechanism for the initial period of CO2 storage at time scale of 100 years.

末次盛冰期以来中国陆地生态系统碳储量变化研究

Carbon is an essential element for life, food and energy. It is also a key element in the greenhouse gases and therefore plays a vital role in climatic changes. The rapid increase in atmospheric concentration of CO_2 over the past 150 years, reaching current concentrations of about 370 ppmv, corresponds with combustion of fossii fuels since the beginning of the industrial age. Conversion of forested land to agricultural use has also redistributed carbon from plants and soils to the atmosphere. These human activities have significantly altered the global carbon cycle. Understanding the consequences of these activities in the coming decades is critical for formulating economic, energy, technology, trade, and security policies that will affect civilization for generations. Under the auspices of the International Geosphere-Biosphere Programme (IGBP), several large international scientific efforts are focused on elucidating the various aspects of the global carbon cycle of the past decade. It is only possible to balance the global carbon cycle for the 1990s if there is net carbon uptake by terrestrial ecosystems of around 2 Pg C/a. There are now some independent, direct evidences for the existence of such a sink. Policymarkers involved in the UN Framework Convention on Climate Change (UN-FCCC) are striving to reach consensuses on a 'safe path' for future emissions, the credible predictions on where and how long the terrestrial sink will either persist at its current level, or grow/decline in the future, are important to advice the policy process. The changes of terrestrial carbon storage depend not only on human activities, but also on biogeochemical and climatological processes and their interaction with the carbon cycles. In this thesis, the climate-induced changes and human-induced changes of carbon storage in China since the past 20,000 years are examined. Based on the data of the soil profiles investigated during China's Second National Soil Survey (1979-1989), the forest biomass measured during China's Fourth National Forest Resource Inventory (1989-1993), the grass biomass investigated during the First National Grassland Resource Survey (1980-1991), and the data collected from a collection of published literatures, the current terrestrial carbon storage in China is estimated to -144.1 Pg C, including -136.8 Pg C in soil and -7.3 Pg C in vegetation. The soil organic (SOC) and inorganic carbon (SIC) storage are -78.2 Pg C and -58.6 Pg C, respectively. In the vegetation reservoir, the forest carbon storage is -5.3 Pg C, and the other of-1.4 Pg C is in the grassland. Under the natural conditions, the SOC, SIC, forest and grassland carbon storage are -85.3 Pg C, -62.6 Pg C, -24.5 Pg C and -5.3 Pg C, respectively. Thus, -29.6 Pg C organic carbon has been lost due to land use with a decrease of -20.6%. At the same time, the SIC storage also has been decreased by -4.0 Pg C (-6.4%). These suggest that human activity has caused significant carbon loss in terrestrial carbon storage of China, especially in the forest ecosystem (-76% loss). Using the Paleocarbon Model (PCM) developed by Wu et al. in this paper, total terrestrial organic carbon storage in China in the Last Glacial Maximum (LGM) was -114.8 Pg C, including -23.1 Pg C in vegetation and -86.7 Pg C in soil. At the Middle Holocene (MH), the vegetation, soil and total carbon were -37.3 Pg C, -93.9 Pg C and -136.0 Pg C, respectively. This implies a gain of-21.2 Pg C in the terrestrial carbon storage from LGM to HM mainly due to the temperature increase. However, a loss of-14.4 Pg C of terrestrial organic carbon occurred in China under the current condition (before 1850) compared with the MH time, mainly due to the precipitation decrease associated with the weakening of the Asian summer monsoon. These results also suggest that the terrestrial ecosystem in China has a substantial potential in the restoration of carbon storage. This might be expected to provide an efficient way to mitigate the greenhouse warming through land management practices. Assuming that half of the carbon loss in the degraded terrestrial ecosystem in current forest and grass areas are restored during the next 50 years or so, the terrestrial ecosystem in China may sequestrate -12.0 Pg of organic carbon from the atmosphere, which represents a considerable offset to the industry's CO2 emission. If the ' Anthropocene' Era will be another climate optimum like MH due to the greenhouse effect, the sequestration would be increased again by -4.3 - 9.0 Pg C in China.

黄土高原22万年来的黑碳记录和古火灾害历史重建

The term black carbon is used to describe a relatively inert and ubiquitous form of carbon, comprising a range of materials from char and charcoal to element or graphite carbon produced by the incomplete combustion of fossil fuels and biomass. Due to its inertness, the BC in soils, lacustrine and marine sediments and ice can persist over a long period of time. So BC signatures in geological deposits can be used as evidence of natural fires happened in their surroundings. To study the temporal and spatial changes in paleofires over the Chinese Loess Plateau, black carbon concentrations were analyzed on the loess-paleosol samples from three sections including Lijiayuan, Lingtai and Weinan along a north-south transect. Using the orbitally-tuned time-scales of the sections, the black carbon sedimentation rates (BCSR) were calculated. Meanwhile, with objective to document fine resolution fire history during late Pleistocene and Holocene periods, we measured BC concentrations of loess-paleosol samples at dense sampling intervals since 28 ka BP. in Lijiayuan section. The BCSR of the samples were also calculated. In addition, we also conducted observation on black carbon morphologies to examine their sources. Based on the results, the following remarks can be concluded: 1. In the last two glacial cycles, the BCSR values in glacial periods are 2-3 times higher than in interglacial periods, and the BCSR variability has a relatively strong precession-associated 23 kyr period, suggesting that the glacial cold-dry climate conditions were apt to induce natural fires over the Loess Plateau, 2. Comparison of the BCSR records among the three loess sections demonstrates that natural fire occurrence was much more intensive and frequent in the northern and interglacial periods. 3. Pollen records and carbon isotope analyses of organic matter have shown that the Loess Plateau was covered by an Artemisia-dominated grassland vegetation both during glacial and interglacial periods, So grassland fires were the dominant fire types in the Plateau, which is also corroborated by the observation of black carbon morphology. In addition, statistics and comparison of BC particle sizes among the sections demonstrated that BC records probably reflected local fires. 4. According to previous studies about the effect of fires on vegetation changes, we considered that the fires might play an important role in the expansion of grassland during glacial periods, besides the control of climate changes. 5. The high resolution black carbon record in Lijiayuan section has shown that the BCSR series well documented Younger dryas (YD) and Heinrich (HI和H2) events, suggesting that natural fires in the northwestern part of Chinese Loess Plateau could regularly respond to the millennial scale climate oscillation.

Electrochemical performance of mixed ionic-electronic conducting oxides as anodes for solid oxide fuel cell

Mixed ionic-electronic conducting (MIEC) oxides, SrFeCo0.5Ox, SrCo0.8Fe0.2O3-delta and La0.6Sr0.4Fe0.8Co0.2O3-delta have been synthesized and prepared on yttria-stabilized zirconia as anodes for solid oxide fuel cells. Power output measurements show that the anodes composed of such kinds of oxides exhibit modest electrochemical activities to both H-2 and CH4 fuels, giving maximum power densities of around 0.1 W/cm(2) at 950 degrees C. Polarization and AC impedance measurements found that large activation overpotentials and ohmic resistance drops were the main causes for the relative inferior performance to the Ni-YSZ anode. While interlayered with an Ni-YSZ anode, a significant improvement in the electrochemical performance was observed. in particular, for the SrFeCo0.5Ox oxide interlayered Ni-YSZ anode, the maximum power output reaches 0.25 W/cm2 on CH,, exceeding those of both SrFeCo0.5Ox and the Ni-YSZ, as anodes alone. A synergetic effect of SrFeCo0.5Ox and the Ni-YSZ has been observed. Future work is needed to examine the long-term stability of MIEC oxide electrodes under a very reducing environment. (C) 1999 Elsevier Science B.V. All rights reserved.

Effect of syngas addition on lower alkene production by the oxidative cracking of hexane

The lower alkene production by the gas-phase oxidative cracking (GOC) or catalytic oxidative cracking (COC) of hexane (C6) with added syngas was investigated. The addition of syngas to the COC process could effectively enhance the selectivity to lower alkenes and decrease the selectivity to COx, because of the preferential reaction between O-2 with H-2 contained in the syngas, whereas it has little effect on the conversion of C6 and product distribution in the GOC process. The high selectivity to lower alkenes of 70% and low selectivity to CO, of 6% at C6 conversion of 66% were achieved over 0.1% Pt/MgAl2O4 catalyst. The COC process of C6 combined with the syngas in the feed could directly produce a gas mixture of lower alkenes, H-2, and CO, which usually is a suitable feedstock for the hydroformylation process.

Thermodynamic properties of ethanol and gasoline blended fuel

The heat capacities (C-p) of five types of gasohol (50 wt % ethanol and 50 wt % unleaded gasoline 93(#) (E50), 60 wt % ethanol and 40 wt % unleaded gasoline 93(#) (E60), 70 wt % ethanol and 30 wt % unleaded gasoline 93(#) (E70), 80 wt % ethanol and 20 wt % unleaded gasoline 93(#) (E80), and 90 wt % ethanol and 10 wt % unleaded gasoline 93(#) (E90), where the "93" denotes the octane number) were measured by adiabatic calorimetry in the temperature range of 78-320 K. A glass transition was observed at 95.61, 96.14, 96.56, 96.84, and 97.08 K for samples from the E50, E60, E70, E80, and E90 systems, respectively. A liquid-solid phase transition and a solid-liquid phase transition were observed in the respective temperature ranges of 118-153 and 155-163 K for E50, 117-150 and 151-164 K for E60, 115-154 and 154-166 K for E70, 113-152 and 152-167 K for E80, and 112-151 and 1581-167 K for E90. The polynomial equations of Cp and the excess heat capacities (C-p(E)), with respect to the thermodynamic temperature, were established through least-squares fitting. Based on the thermodynamic relationship and the equations obtained, the thermodynamic functions and the excess thermodynamic functions of the five gasohol samples were derived.

A genetic algorithm based economic dispatch (GAED) with environmental constraint optimisation

The role of renewable energy in power systems is becoming more significant due to the increasing cost of fossil fuels and climate change concerns. However, the inclusion of Renewable Energy Generators (REG), such as wind power, has created additional problems for power system operators due to the variability and lower predictability of output of most REGs, with the Economic Dispatch (ED) problem being particularly difficult to resolve. In previous papers we had reported on the inclusion of wind power in the ED calculations. The simulation had been performed using a system model with wind power as an intermittent source, and the results of the simulation have been compared to that of the Direct Search Method (DSM) for similar cases. In this paper we report on our continuing investigations into using Genetic Algorithms (GA) for ED for an independent power system with a significant amount of wind energy in its generator portfolio. The results demonstrate, in line with previous reports in the literature, the effectiveness of GA when measured against a benchmark technique such as DSM.

Tecnologias CAC e Inquéritos de Percepção da Opinião Pública sobre “O papel da Captação e do Armazenamento/Sequestração de Dióxido de Carbono no Futuro da Energia na Europa”:O caso-de-estudo da Comunidade Fernando Pessoa

O carvão e outros combustíveis fósseis, continuarão a ser, por décadas, a principal matéria-prima energética para as Centrais Térmicas, não obstante os esforços para, dentro do possível, substituir os combustíveis fósseis por fontes de energia renovável.Tal como está, hoje, bem documentado, a produção de gases com efeito estufa (GEE), designadamente CO2, resulta da combustão dos ditos combustíveis fósseis, sendo que se espera ser possível mitigar substancialmente a emissão de tais gases com a aplicação das chamadas Tecnologias Limpas do Carvão.Há, pois, necessidade de promover o abatimento do CO2 através de Tecnologias de Emissão Zero ou Tecnologias Livres de Carbono, incluindo designadamente a Captura, o Transporte e a Sequestração geológica de CO2 correspondentes ao que é costume designar por Tecnologias CAC (Captação e Armazenamento de Carbono). De facto, tais tecnologias e, designadamente, o armazenamento geológico de CO2 são as únicas que, no estado actual do conhecimento, são capazes de permitir que se cumpram as metas do ambicioso programa da EU para a energia e o ambiente conhecido por “20 20 para 2020” em conjugação com os aspectos económicos das directivas relativas ao Comércio Europeu de Licenças de Emissão – CELE (Directivas 2003/87/EC, 2004/101/EC e 2009/29/EC).A importância do tema está, aliás, bem demonstrada com o facto da Comissão Europeia ter formalmente admitido que as metas supracitadas serão impossíveis de atingir sem Sequestração Geológica de CO2. Esta é, pois, uma das razões de ter sido recentemente publicada a Directiva Europeia 2009/31/EC de 23 de Abril de 2009 expressamente dedicada ao tema do Armazenamento Geológico de CO2.Ora, a questão do armazenamento geológico de CO2 implica, para além das Tecnologias CAC acima mencionadas e da sua viabilização em termos tanto técnicos como económicos, ou seja, neste último aspecto, competitiva com o sistema CELE, também o conhecimento, da percepção pública sobre o assunto. Isto é, a praticabilidade das Tecnologias CAC implica que se conheça a opinião pública sobre o tema e, naturalmente, que face a esta realidade se prestem os esclarecimentos necessários como, aliás, é reconhecido na própria Directiva Europeia 2009/31/EC.Dado que a Fundação Fernando Pessoa / Universidade Fernando Pessoa através do seu Centro de Investigação em Alterações Globais, Energia, Ambiente e Bioengenharia – CIAGEB tem ultimado um Projecto de Engenharia relativo à Sequestração Geológica de CO2 nos Carvões (Metantracites) da Bacia Carbonífera do Douro – o Projecto COSEQ, preocupou-se naturalmente, desde o início, com o lançamento de inquéritos de percepção da opinião pública sobre o assunto.Tal implicou, nesta fase, a tradução para português e o lançamento do inquérito europeu ACCSEPT que não tinha sido ainda formalmente lançado de forma generalizada entre nós. Antes, porém, de lançar publicamente tal inquérito – o que está actualmente já em curso – resolveu-se testar o método de lançamento, a recolha de dados e o seu tratamento com uma amostra correspondente ao que se designou por Comunidade Fernando Pessoa, i.e. o conjunto de docentes, discentes, funcionários e outras pessoas relacionadas com a Universidade Fernando Pessoa (cerca de 5000 individualidades).Este trabalho diz, precisamente, respeito à preparação, lançamento e análise dos resultados do dito inquérito Europeu ACCSEPT a nível da Comunidade Fernando Pessoa. Foram recebidas 525 respostas representando 10,5% da amostra. A análise de resultados foi sistematicamente comparada com os obtidos nos outros países europeus, através do projecto ACCSEPT e, bem assim, com os resultados obtidos num inquérito homólogo lançado no Brasil. The use of coal, and other fossil fuels, will remain for decades as the main source of energy for power generation, despite the important efforts made to replace, as far as possible, fossil fuels with renewable power sources.As is well documented, the production of Greenhouse Gases (GHG), mainly CO2, arises primarily from the combustion of fossil fuels. The increasing application of Clean Coal Technologies-CCTs, is expected to mitigate substantially against the emission of such gases.There is consequently a need to promote the CO2 abatement through Zero Emission (Carbon Free) Technologies - ZETs, which includes CO2 capture, transport and geological storage, i.e. the so-called CCS (Carbon, Capture and Storage) technologies. In fact, these technologies are the only ones that are presently able to conform to the ambitious EU targets set out under the “20 20 by 2020” EU energy and environment programme, jointly with the economic aspects of the EU Directives 2003/87/EC, 2004/101/EC and 2009/29/EC concerned with the Greenhouse Gas Emissions Allowance Trading Scheme – ETS scheme. The European Commission formal admission that the referred targets will be impossible to reach without the implementation and contribution of geological storage clearly demonstrate the importance of this particular issue, and for this reason the EC Directive 2009/31/EC of April 23, 2009 on Geological Storage of CO2 was recently published.In considering the technical and economical viabilities of CCS technologies, the latter in competition with the ETS scheme, it is believed that public perception will dictate the success of the development and implementation of CO2 geological storage at a large industrial level. This means that, in order to successfully implement CCS technologies, not only must public opinion be taken into consideration but objective information must also be provided to the public in order to raise subject awareness, as recognized in the referred Directive 2009/31/EC.In this context, the Fernando Pessoa Foundation / University Fernando Pessoa, through its CIAGEB (Global Change, Energy, Environment and Bioengineering) RDID&D Unit, is the sponsor of an Engineering Project for the Geological Sequestration of CO2 in Douro Coalfield Meta-anthracites - the COSEQ Project, and is therefore also engaged in public perception surveys with regards to CCS technologies.At this stage, the original European ACCSEPT inquiry was translated to Portuguese and submitted only to the “Fernando Pessoa Community” - comprising university lecturers, students, other employees, as well as, former students and persons that have a professional or academic relationship with the university (c. 5000 individuals). The results obtained from this first inquiry will be used to improve the survey informatics system in terms of communication, database, and data treatment prior to resubmission of the inquiry to the Portuguese public at large.The present publication summarizes the process and the results obtained from the ACCSEPT survey distributed to the “Fernando Pessoa Community”. 525 replies, representing 10.5% of the sample, have been received and analysed. The assessment of the results was systematically compared with those obtained from other European Countries, as reported by the ACCSEPT inquiry, as well as with those from an identical inquiry launched in Brazil.

High-efficiency photovoltaics through mechanically stacked integration of solar cells based on the InP lattice constant

Solar Energy is a clean and abundant energy source that can help reduce reliance on fossil fuels around which questions still persist about their contribution to climate and long-term availability. Monolithic triple-junction solar cells are currently the state of the art photovoltaic devices with champion cell efficiencies exceeding 40%, but their ultimate efficiency is restricted by the current-matching constraint of series-connected cells. The objective of this thesis was to investigate the use of solar cells with lattice constants equal to InP in order to reduce the constraint of current matching in multi-junction solar cells. This was addressed by two approaches: Firstly, the formation of mechanically stacked solar cells (MSSC) was investigated through the addition of separate connections to individual cells that make up a multi-junction device. An electrical and optical modelling approach identified separately connected InGaAs bottom cells stacked under dual-junction GaAs based top cells as a route to high efficiency. An InGaAs solar cell was fabricated on an InP substrate with a measured 1-Sun conversion efficiency of 9.3%. A comparative study of adhesives found benzocyclobutene to be the most suitable for bonding component cells in a mechanically stacked configuration owing to its higher thermal conductivity and refractive index when compared to other candidate adhesives. A flip-chip process was developed to bond single-junction GaAs and InGaAs cells with a measured 4-terminal MSSC efficiency of 25.2% under 1-Sun conditions. Additionally, a novel InAlAs solar cell was identified, which can be used to provide an alternative to the well established GaAs solar cell. As wide bandgap InAlAs solar cells have not been extensively investigated for use in photovoltaics, single-junction cells were fabricated and their properties relevant to PV operation analysed. Minority carrier diffusion lengths in the micrometre range were extracted, confirming InAlAs as a suitable material for use in III-V solar cells, and a 1-Sun conversion efficiency of 6.6% measured for cells with 800 nm thick absorber layers. Given the cost and small diameter of commercially available InP wafers, InGaAs and InAlAs solar cells were fabricated on alternative substrates, namely GaAs. As a first demonstration the lattice constant of a GaAs substrate was graded to InP using an InxGa1-xAs metamorphic buffer layer onto which cells were grown. This was the first demonstration of an InAlAs solar cell on an alternative substrate and an initial step towards fabricating these cells on Si. The results presented offer a route to developing multi-junction solar cell devices based on the InP lattice parameter, thus extending the range of available bandgaps for high efficiency cells.

Feasibility of combined wind-wave energy platforms

The European Union has set out an ambitious 20% target for renewable energy use by 2020. It is expected that this will be met mainly by wind energy. Looking towards 2050, reductions in greenhouse gas emissions of 80-95% are to be sought. Given the issues securing this target in the transport and agriculture sectors, it may only be possible to achieve this target if the power sector is carbon neutral well in advance of 2050. This has permitted the vast expansion of offshore renewables, wind, wave and tidal energy. Offshore wind has undergone rapid development in recent years however faces significant challenges up to 2020 to ensure commercial viability without the need for government subsidies. Wave energy is still in the very early stages of development so as yet there has been no commercial roll out. As both of these technologies are to face similar challenges in ensuring they are a viable alternative power generation method to fossil fuels, capitalising on the synergies is potentially a significant cost saving initiative. The advent of hybrid solutions in a variety of configurations is the subject of this thesis. A singular wind-wave energy platform embodies all the attributes of a hybrid system, including sharing space, transmission infrastructure, O&M activities and a platform/foundation. This configuration is the subject of this thesis, and it is found that an OWC Array platform with multi-MegaWatt wind turbines is a technically feasible, and potentially an economically feasible solution in the long term. Methods of design and analysis adopted in this thesis include numerical and physical modelling of power performance, structural analysis, fabrication cost modelling, simplified project economic modelling and time domain reliability modelling of a 210MW hybrid farm. The application of these design and analysis methods has resulted in a hybrid solution capable of producing energy at a cost between €0.22/kWh and €0.31/kWh depending on the source of funding for the project. Further optimisation through detailed design is expected to lower this further. This thesis develops new and existing methods of design and analysis of wind and wave energy devices. This streamlines the process of early stage development, while adhering to the widely adopted Concept Development Protocol, to develop a technically and economically feasible, combined wind-wave energy hybrid solution.

Design, fabrication and characterisation of components for microfluidic enzymatic biofuel cells

The concept of a biofuel cell takes inspiration from the natural capability of biological systems to catalyse the conversion of organic matter with a subsequent release of electrical energy. Enzymatic biofuel cells are intended to mimic the processes occurring in nature in a more controlled and efficient manner. Traditional fuel cells rely on the use of toxic catalysts and are often not easily miniaturizable making them unsuitable as implantable power sources. Biofuel cells however use highly selective protein catalysts and renewable fuels. As energy consumption becomes a global issue, they emerge as important tools for energy generation. The microfluidic platforms developed are intended to maximize the amount of electrical energy extracted from renewable fuels which are naturally abundant in the environment and in biological fluids. Combining microfabrication processes, chemical modification and biological surface patterning these devices are promising candidates for micro-power sources for future life science and electronic applications. This thesis considered four main aspects of a biofuel cell research. Firstly, concept of a miniature compartmentalized enzymatic biofuel cell utilizing simple fuels and operating in static conditions is verified and proves the feasibility of enzyme catalysis in energy conversion processes. Secondly, electrode and microfluidic channel study was performed through theoretical investigations of the flow and catalytic reactions which also improved understanding of the enzyme kinetics in the cell. Next, microfluidic devices were fabricated from cost-effective and disposable polymer materials, using the state-of-the-art micro-processing technologies. Integration of the individual components is difficult and multiple techniques to overcome these problems have been investigated. Electrochemical characterization of gold electrodes modified with Nanoporous Gold Structures is also performed. Finally, two strategies for enzyme patterning and encapsulation are discussed. Several protein catalysts have been effectively immobilized on the surface of commercial and microfabricated electrodes by electrochemically assisted deposition in sol-gel and poly-(o-phenylenediamine) polymer matrices and characterised with confirmed catalytic activity.

Oil and gas projects in the Western Amazon: threats to wilderness, biodiversity, and indigenous peoples.

BACKGROUND: The western Amazon is the most biologically rich part of the Amazon basin and is home to a great diversity of indigenous ethnic groups, including some of the world's last uncontacted peoples living in voluntary isolation. Unlike the eastern Brazilian Amazon, it is still a largely intact ecosystem. Underlying this landscape are large reserves of oil and gas, many yet untapped. The growing global demand is leading to unprecedented exploration and development in the region. METHODOLOGY/PRINCIPAL FINDINGS: We synthesized information from government sources to quantify the status of oil development in the western Amazon. National governments delimit specific geographic areas or "blocks" that are zoned for hydrocarbon activities, which they may lease to state and multinational energy companies for exploration and production. About 180 oil and gas blocks now cover approximately 688,000 km(2) of the western Amazon. These blocks overlap the most species-rich part of the Amazon. We also found that many of the blocks overlap indigenous territories, both titled lands and areas utilized by peoples in voluntary isolation. In Ecuador and Peru, oil and gas blocks now cover more than two-thirds of the Amazon. In Bolivia and western Brazil, major exploration activities are set to increase rapidly. CONCLUSIONS/SIGNIFICANCE: Without improved policies, the increasing scope and magnitude of planned extraction means that environmental and social impacts are likely to intensify. We review the most pressing oil- and gas-related conservation policy issues confronting the region. These include the need for regional Strategic Environmental Impact Assessments and the adoption of roadless extraction techniques. We also consider the conflicts where the blocks overlap indigenous peoples' territories.

Seeing the forest for the fuel

We demonstrate a new approach to understanding the role of fuelwood in the rural household economy by applying insights from travel cost modeling to author-compiled household survey data and meso-scale environmental statistics from Ruteng Park in Flores, Indonesia. We characterize Manggarai farming households' fuelwood collection trips as inputs into household production of the utility yielding service of cooking and heating. The number of trips taken by households depends on the shadow price of fuelwood collection or the travel cost, which is endogenous. Econometric analyses using truncated negative binomial regression models and correcting for endogeneity show that the Manggarai are 'economically rational' about fuelwood collection and access to the forests for fuelwood makes substantial contributions to household welfare. Increasing cost of forest access, wealth, use of alternative fuels, ownership of kerosene stoves, trees on farm, park staff activity, primary schools and roads, and overall development could all reduce dependence on collecting fuelwood from forests. © 2004 Cambridge University Press.