Pré-concentração de Cr(III) e análise de especiação de cromo empregando montmorilonita saturada com íons potássio

The clay mineral montmorillonite-K10 (MT), treated under acidic medium and saturated with potassium ions (MTK), was employed in sorption and desorption studies aiming the preconcentration of Cr(III) and the speciation analysis of chromium. The sorption process of Cr(III) was close to 100%, suggesting that MTK was a good material for Cr(III) preconcentration, although, the maximum recovery in HNO3 solution was near 89%. On the other hand, Cr(VI) practically was not retained in MTK, suggesting this material as an appropriate mineral phase to be used in speciation analysis of chromium in aqueous medium.

Development and validation of a dissolution test for diltiazem hydrochloride in immediate release capsules

This work describes the development and validation of a dissolution test for 60 mg of diltiazem hydrochloride in immediate release capsules. The best dissolution in vitro profile was achieved using potassium phosphate buffer at pH 6.8 as the dissolution medium and paddle as the apparatus at 50 rpm. The drug concentrations in the dissolution media were determined by UV spectrophotometry and HPLC and a statistical analysis revealed that there were significant differences between HPLC and spectrophotometry. This study illustrates the importance of an official method for the dissolution test, since there is no official monograph for diltiazem hydrochloride in capsules.

Encapsulation of naproxen in nanostructured system: structural characterization and in vitro release studies

Nanoparticles were produced by solvent emulsification evaporation method with the following characteristics: nanometric size (238 ± 3 nm), narrow polydispersity index (0.11), negative zeta potential (-15.1 mV), good yield of the process (73 ± 1.5%), excellent encapsulation efficiency (81.3 ± 4.2%) and spherical shape. X-rays diffraction demonstrated the loss of drug crystallinity after encapsulation; however, the profile of the diffractograms of the poly-ε-caprolactone (PCL) nanoparticles was kept. Differential scanning calorimetry thermograms, correspondingly, exhibited the loss of drug melting peak and the increasing of the melting point of the PCL nanoparticles, evidencing an interaction drug-polymer. Naproxen release was low and sustained obeying the Higuchi´s kinetic. The results show that nanoparticles are promising sustained release system to the naproxen.

Determinación simultánea de Cr, Ni y V en orina mediante et aas

A procedure for the simultaneous determination of Cr, Ni, and V in urine by electrothermal atomic absorption spectrometry (ET AAS) was optimized by factorial design, and performed at a pyrolysis and atomization temperatures of 1300 and 2500 ºC, respectively, using 15 µg de Mg(NO3)2 as chemical modifier. Characteristics mass of 14, 6 and 220 ρg and detection limits of the method of 0.07, 0.38 and 0.75 µg L-1 were obtained for Cr, Ni and V respectively. The methodology was validated using a Liphochek Urine Metals Control sample (Bio-Rad) (P=0.05). The methodology was applied to samples of voluntary Venezuelan people, not environmentally exposed to specific emissions, and results ranging from < LOD-1.1 and 1.3-3.3 µg L-1 was observed for Cr and V, respectively, and not detectable levels for Ni.

Poly(ethylene-co-methyl acrylate)/poly(caprolactone) triol blends for drug delivery systems: characterization and drug release

Poly(ethylene-co-methyl acrylate) (EMA) and poly (caprolactone) triol (PCL-T) blends, a biodegradable aliphatic polyester with low molecular weight and moderate water solubility containing diltiazem hydrochloride (DZ) were studied in terms of the thermal and morphological properties, and drug release mechanism. An increase in the PCL-T content in the EMA/PCL-T/DZ films decreased the degree of DZ crystallinity. Drug release from these films is temperature-dependent, and it is possible to modify the drug release rate by adjusting the EMA/PCL-T composition of the blends. The mechanism of drug release is governed by PCL-T melting and PCL-T leaching from EMA matrix.

Characterization and in vitro release of cyclosporine-A from poly(D,L-lactide-co-glycolide implants obtained by solvent/extraction evaporation

Cyclosporine-A-loaded PLGA implants were developed intended for ocular route. Implants were prepared using solvent extraction/evaporation technique followed by casting of the cake into rods in a heated surface. XRD patterns showed that cyclosporine-A was completely incorporated into PLGA. FTIR and DSC results indicated alterations on drug molecular conformation aiming to reach the most stable thermodynamic conformation at polymer/drug interface. Implants provided controlled/sustained in vitro release of the drug. During the first 7 weeks, the drug release was controlled by the diffusion of the cyclosporine-A; and between 7-23 week period, the drug diffusion and degradation of PLGA controlled the drug release.

Biomonitoramento de Cr e Pb em peixes de água doce

Trace metal content of three fish species harvested from a tank located in the City of Guarapuava-PR, Brazil were determined by digestion and voltametry. Trace metal content in fish samples were 0.10-1.30 µg/g (muscle) and 0.45-15.90 µg/g (liver) for chromium, 0.35-2.56 µg/g (muscle) and 2.32-34.30 µg/g (liver) for lead. The levels of lead and chromium in fish samples were higher than the recommended legal limits for human consumption. To assess the dietary intake of Cr and Pb by fish, weekly intake was calculated based on average metals contents and weekly consumption of fish and it compared with PTWI (Provisional Tolerable Weekly Intake). The Cr and Pb have achieved up to 25 and 45%, respectively, of PTWI recommended by WHO/FAO.

A fluorescence-based assay for octreotide in kinetic release from depot formulations

Here we report the validation of a derivatization method that makes use of fluorescamine as a selective reactant for the quantitative analysis of peptide and protein drugs in the dissolution profile from depot formulations. Typical current methods require separation of the nano/microparticles and time-consuming chromatographic runs. In this study we report a method which can be conducted without the need for complete physical separation of the particles or removal of the unreacted probe. This method was used here for the analysis of the release profile of octreotide in a depot formulation, with results in excellent agreement with reported chromatographic assays.

Indirect spectrophotometric method for determination of captopril using Cr(VI) and diphenylcarbazide

A spectrophotometric method for the indirect determination of captopril (CP) in pharmaceutical formulations is proposed. The proposed procedure is based on the oxidation of captopril by potassium dichromate and the determination excess oxidant on the basis of its reaction with diphenylcarbazide (DPC). Under the optimum conditions, a good linear relationship (r = 0.9997) was obtained in the range of 0.08-3.5 µg mL-1. The assay limits of detection and quantitation were 0.024 and 0.08 µg mL-1, respectively. The results obtained for captopril determination in pharmaceuticals using the proposed method and those obtained with the US Pharmacopoeia method were in good agreement at the 95% confidence level.

Interaction of naproxen with calcium carbonate: physicochemical characterization and in vitro drug release studies

Interaction and physicochemical characterization of dispersions of naproxen in calcium carbonate after freeze-drying the wet-state equilibrated mixture have been investigated by analytical methods. The FT-IR study revealed the acid-base reaction between naproxen and calcium carbonate. The DSC study indicated physical interaction and significantly diminished crystallinity of naproxen in the formulation containing higher quantities of calcium carbonate. Furthermore, the SEM study showed the reduced particle size and loss of crystalline morphology in the same sample. Drug release increased with the increase of calcium carbonate in the formulations. Formulation of naproxen with calcium carbonate in 1:2 ratio allowed its dissolution to the greatest extent (94.96%) while other compositions, 1:0.5 and 1:1, showed 80.86% and 78.30% release, respectively.

Transdermal formulations containing human sexual steroids: development and validation of methods and in vitro drug release

In vitro release of bioidentical hormones in four different liposomal transdermal emulsions (containing testosterone, progesterone, estradiol, or estradiol and estriol) was assessed. For this purpose, novel high-performance liquid chromatography methods were developed and validated in an eco-friendly manner and used to determine the in vitro release of such products. The methods were suitable for our intended goal, and the emulsions employed were found to be effective as transporting candidates for the efficient release of hormones in the transdermal delivery of human sexual steroids.

Green tea in transdermal formulation: HPLC method for quality control and in vitro drug release assays

RP-HPLC based analytical method for use in both quality control of green tea in a semisolid formulation and for in vitro drug release assays was developed and validated. The method was precise (CV < 5%), accurate (recovery between 98% and 102%), linear (R² > 0.99), robust, and specific for the determination of epigallocatechin 3-gallate (EGCG), caffeine (CAF), and gallic acid (GA). In a diffusion cell chamber, the release rate of EGCG was 8896.01 µg cm-2. This data showed that EGCG will be able to exert its systemic activity when delivered though the transdermal formulation, due to its good flux rates with the synthetic membrane.

Preparation and evaluation of magnetic chitosan particles modified with ethylenediamine and Fe(III) for the removal of Cr(VI) from aqueous solutions

The adsorption of Cr(VI) in aqueous solution by magnetic particles of crosslinked chitosan-ethylenediamine-Fe(III) (MPCh-EDA-FeCL) was studied in a batch system. Fe3+ in the MPCh-EDA-FeCL permitted that adsorption of Cr(VI) occurred with maximum efficiency between pH 3 and 11. The maximum adsorption capacity at pH 7.0 was 81.04 mg g-1 at 25 ºC. The adsorption kinetic process was described by the pseudo-second-order model. Thermodynamic parameters indicated spontaneous, exothermic and chemical adsorption nature. The adsorbent was successively regenerated using a 0.1 mol L-1 NaOH solution. Results were satisfactory for treatment of wastewater from the electroplating industry.

Effect of magnesium addition on the vacancy-Mg binding free enthalpy in Al-Cr alloys

The Mg-vacancy binding free enthalpy of Al-Cr solid solution alloys with Mg addition was calculated by electrical resistivity measurements. The obtained value is lower than that obtained for dilute Al-Mg alloys with almost the same Mg content and may be attributed to the diffusion of Mg.

Distribuição de Cr, Ni, Cu, Cd e Pb em frações húmicas de diferentes tamanhos moleculares extraídas de amostras de água e de sedimentos do reservatório de captação de água superficial Anhumas - Araraquara-SP

Estudou-se a distribuição de Cr, Ni, Cu, Cd e Pb em frações de substâncias húmicas (SH) de diferentes tamanhos moleculares. As SH foram extraídas de amostras de água (SHA) e de sedimentos de superfície (SHSS), interface/água (SHSI) e fundo (SHSF) coletados no reservatório de captação de água superficial Anhumas, localizado no município de Araraquara-SP. Para a extração das SH utilizaram-se os procedimentos recomendados pela Sociedade Internacional de Substâncias Húmicas. Após purificação por diálise, as SH foram fracionadas com base no tamanho molecular utilizando-se sistema de fracionamento seqüencial por ultrafiltração e fluxo tangencial. O fracionamento das amostras de SHA permitiu caracterizar uma distribuição de massa relativamente uniforme dentre as frações de diferentes tamanhos moleculares, com valores maiores nas frações F2 (20,8%) e F4 (23,8%). Exceto para os íons Pb(II) e Cu(II) os quais apresentaram concentrações relativamente mais altas nas frações F2 e F4, respectivamente, de maneira geral, crômio, níquel, cádmio e chumbo têm distribuições similares nas cinco frações com tamanhos moleculares maiores e médios (F1 a F5). Quanto às distribuições de massa nas diferentes frações de substâncias húmicas extraídas de amostras de sedimento de superfície (SHSS), sedimento interface/água (SHSI) e sedimento de fundo (SHSF), as três amostras apresentaram 42-48% das SH nas frações com maiores tamanhos moleculares (F1 e F2), 29-31% nas frações intermediárias (F3 e F4) e 13-20% nas frações com menores tamanhos moleculares (F5 e F6). De modo geral, caracterizaram-se para os íons metálicos, distribuições similares dentre as respectivas frações F1 a F6. Exceções para Pb(II) e Ni(II) em sedimento de superfície com concentrações relativamente menores nas frações F2 e F4, respectivamente.