A DC-DC Step-Up mu-Power Converter for Energy Harvesting Applications, Using Maximum Power PointTracking, Based on Fractional Open Circuit Voltage

A DC-DC step-up micro power converter for solar energy harvesting applications is presented. The circuit is based on a switched-capacitorvoltage tripler architecture with MOSFET capacitors, which results in an, area approximately eight times smaller than using MiM capacitors for the 0.131mu m CMOS technology. In order to compensate for the loss of efficiency, due to the larger parasitic capacitances, a charge reutilization scheme is employed. The circuit is self-clocked, using a phase controller designed specifically to work with an amorphous silicon solar cell, in order to obtain themaximum available power from the cell. This will be done by tracking its maximum power point (MPPT) using the fractional open circuit voltage method. Electrical simulations of the circuit, together with an equivalent electrical model of an amorphous silicon solar cell, show that the circuit can deliver apower of 1132 mu W to the load, corresponding to a maximum efficiency of 66.81%.

A Step-up mu-Power Converter for Solar Energy Harvesting Applications, using Hill Climbing Maximum Power Point Tracking

This paper presents a step-up micro-power converter for solar energy harvesting applications. The circuit uses a SC voltage tripler architecture, controlled by an MPPT circuit based on the Hill Climbing algorithm. This circuit was designed in a 0.13 mu m CMOS technology in order to work with an a-Si PV cell. The circuit has a local power supply voltage, created using a scaled down SC voltage tripler, controlled by the same MPPT circuit, to make the circuit robust to load and illumination variations. The SC circuits use a combination of PMOS and NMOS transistors to reduce the occupied area. A charge re-use scheme is used to compensate the large parasitic capacitors associated to the MOS transistors. The simulation results show that the circuit can deliver a power of 1266 mu W to the load using 1712 mu W of power from the PV cell, corresponding to an efficiency as high as 73.91%. The simulations also show that the circuit is capable of starting up with only 19% of the maximum illumination level.

A marcha humana: circuitos neuronais entre estruturas corticais vs sub-corticais

As conexões entre os níveis corticais e sub-corticais na activação da marcha Humana carecem de discussão. As alterações da marcha por lesão no território da Artéria Cerebral Média (ACM) podem ser explicadas pela disfunção de circuitos neuronais dos Núcleos da Base ao córtex e Núcleos Pedúnculo-Pontino. Este trabalho tem como objectivo identificar os percursos anatómicos das principais conexões entre as estruturas encefálicas referidas no território da ACM. Com base na topografia das conexões neuronais, é aceitável que as alterações da marcha sejam explicadas por alterações na função dos Núcleos da Base, através das suas conexões, enquanto moduladores da actividade motora.

Avaliação da caracterização de lesões em mamografia com recurso a sistemas CAD (Diagnóstico Assistido por Computador)

Mestrado em Radiações Aplicadas às Tecnologias da Saúde. Área de especialização: Imagem Digital com Radiação X.

Toxicidade a cianobactérias: impacte potencial na saúde pública em populações de Portugal e Brasil

Como recurso natural fundamental à vida, a água e os ecossistemas aquáticos devem ser alvo de avaliação contínua, no que se reporta à sua qualidade física, química e biológica. Segundo a Organização Mundial de Saúde cerca de 1,1 biliões de pessoas estão impossibilitadas em aceder a qualquer tipo de água potável e, as populações residentes nas proximidades de rios, lagoas, e reservatórios utilizam estas águas para as suas necessidades de consumo, aumentando o risco de transmissão de doenças. Enquanto constituintes da comunidade fitoplanctónica, as cianobactérias são microrganismos procariotas, fotossintéticos, que obtêm os nutrientes diretamente da coluna de água e, um aumento da concentração de nutrientes (principalmente azoto e fósforo), associado a condições ambientais favoráveis, pode desencadear um crescimento rápido originando fluorescências. Sob determinadas condições as cianobactérias podem produzir toxinas existindo registos que evidenciam que fluorescências toxicas são responsáveis pelo envenenamento agudo e morte de animais e humanos pelo que, a água utilizada para consumo humano deverá ser regularmente monitorizada para este elemento biológico. O objetivo deste estudo é relacionar a ocorrência de fluorescências de cianobactérias (> 2000 cel/ml) e toxicidade associada, com o impacte potencial na Saúde Pública avaliado através do consumo direto ou indireto da água. Em Portugal foram selecionados oito reservatórios situados na região Sul, pertencentes às bacias hidrográficas do Sado e Guadiana e estudados entre 2000 e 2008. No Brasil foram selecionados os reservatórios de Três Marias (Estado de Minas Gerais) e de Tucuruí (Estado do Pará) e estudados em 2005 e 2006 respetivamente. Os reservatórios foram caracterizados em termos físicos e químicos, tendo-se igualmente procedido à caracterização da comunidade fitoplanctónica através da identificação e quantificação dos principais grupos presentes em diferentes épocas do ano. Em termos fitoplanctónicos os reservatórios portugueses apresentaram maior diversidade,verificando-se contudo dominância das cianobactérias na comunidade. Associados a fluorescências, foram registados nestes reservatórios géneros produtores de hepato e neurotoxinas como Aphanizomenon sp, Microcystis aeruginosa e Oscillatoria sp. No Brasil, em situação de fluorescências, os géneros produtores de neuro e hepatotoxinas foram Microcystis (> 350.000 cels/ml) e Cylindrospermopsis. A presença destes géneros, poderá constituir um risco potencial para a saúde pública, pelo que é importante a implementação de medidas de mitigação em todos os reservatórios objeto de estudo, devendo essa atuação passar pelo controle do estado trófico no sentido de evitar o desenvolvimento de fluorescências. Assim sugere-se a implementação de um tratamento adequado para a produção de água de consumo e a organização de ações de sensibilização e aviso e informação às populações que utilizam os reservatórios em Portugal e no Brasil para diversos usos. - ABSTRACT - As a life fundamental natural resource, water and aquatic ecosystems must be continuously evaluated in their physical, chemical and biological quality. According World Health Organization, 1.1 billion people has no chance to access any kind of potable water. Populations living near rivers, lagoons or reservoirs use those waters to content their needs, increasing risks disease transmission. As members of phytoplankton community, cyanobacteria are prokaryotic, photosynthetic microorganisms and get its nutrients directly from water column. The increase of this nutrients (especially nitrogen and phosphorus) associated with favorable environment conditions, can support a sudden grow and instigate blooms. Under specific conditions cyanobacteria can produce toxins and several records have shown that toxic blooms are responsible by acute poisoning and death in animals and humans so, water for human consumption must be regularly surveyed for this biologic element. The aim of this study is to correlate Cyanobacteria blooms (>2.000cels/ml) and connected toxicity with public health impact, evaluated through water consumption. In Portugal, eight reservoirs located in the South region were selected and study between 2000 and 2008. In Brazil, Três Marias reservoir (Minas Gerais Provence) and Tucuruí (Pará Provence) were selected and study in 2005 and 2006. Reservoirs were characterized in physical and chemical aspects, as well as phytoplankton community, through identification and counting of main present groups along study period. In bloom circumstances, liver toxins and neurotoxins producers like Aphanizomenon sp, Microcystis aeruginosa and Oscillatoria sp. were founded in Portuguese reservoirs. In Brazil, cyanobacteria genera involved in toxic bloom were Microcystis (> 350.000 cels/ml) and Cylindrospermopsis. This genera presence represents a potential risk for public health, and show the requirement to implement mitigation measures in all study reservoirs. These measures can be represented by water eutrophication control to avoid blooms, by appropriate treatments of water to human consumption, and public warnings or information to dose people in Portugal and Brazil that use these reservoirs to several activities.

Materiais estruturados: qual o seu papel na aprendizágem dos primeiros números?

Dissertação apresentada para obtenção do grau de Mestre em Educação Matemática na Educação Pré-Escolar e no 1.º e 2.º Ciclos do Ensino Básico

Lead, hemoglobin, zinc protoporphyrin and ferritin concentrations in children

OBJECTIVE: To assess the relationship of blood lead and hemoglobin, zinc protoporphyrin, and ferritin concentrations in children. METHODS: A cross-sectional study was carried out in 136 anemic and non-anemic children from two rural villages near a lead smelter in Adrianópolis, Southern Brazil, from July to September 2001. Hemoglobin electrophoresis was performed to exclude children with hemoglobin variants and thalassemia syndromes associated with anemia. Lead was determined by atomic absorption spectrophotometry; hemoglobin by automated cell counting; zinc protoporphyrin by hematofluorometry; ferritin by chemiluminescence. Student's t-test, Mann-Whitney test, and the c² test were used to assess the significance of the differences between the variables investigated in anemic and non-anemic children. Stepwise multivariate linear regression analysis was performed using two models for anemic and non-anemic children respectively. RESULTS: Lead was negatively associated to hemoglobin (p<0.017) in the first model, and in the second model lead was positively associated to zinc protoporphyrin (p<0.004) after controlling for ferritin, age, sex, and per capita income. There was an inverse association between hemoglobin and blood lead in anemic children. It was not possible to confirm if anemic children had iron deficiency anemia or subclinical infection, considering that the majority (90.4%) had normal ferritin. CONCLUSIONS: The study detected a relationship between anemia and elevated blood lead concentrations. Further epidemiological studies are necessary to investigate the impact of iron nutritional interventions as an attempt to decrease blood lead in children.

A Voltage Limiter Circuit for Indoor Light Energy Harvesting Applications

A voltage limiter circuit for indoor light energy harvesting applications is presented. This circuit is a part of a bigger system, whose function is to harvest indoor light energy, process it and store it, so that it can be used at a later time. This processing consists on maximum power point tracking (MPPT) and stepping-up, of the voltage from the photovoltaic (PV) harvester cell. The circuit here described, ensures that even under strong illumination, the generated voltage will not exceed the limit allowed by the technology, avoiding the degradation, or destruction, of the integrated die. A prototype of the limiter circuit was designed in a 130 nm CMOS technology. The layout of the circuit has a total area of 23414 mu m(2). Simulation results, using Spectre, are presented.

Design of a Multiband Full-Rate Ultra-Wideband Receiver in FPGA

MultiBand OFDM (MB-OFDM) UWB [1] is a short-range promising wireless technology for high data rate communications up to 480 Mbps. In this paper, we have designed and implemented in an Virtex-6 FPGA an MB-OFDM UWB receiver for the highest data rate of 480 Mbps. To test the system, we have also implemented an MB-OFDM transmitter and an AWGN generator in VHDL and determined the bit error rates at the receiver running in an FPGA.

A 5GHz/1.8V CMOS Active Balun Integrated with LNA

The development of high performance monolithic RF front-ends requires innovative RF circuit design to make the best of a good technology. A fully differential approach is usually preferred, due to its well-known properties. Although the differential approach must be preserved inside the chip, there are cases where the input signal is single-ended such as RF image filters and IF filters in a RF receiver. In these situations, a stage able to convert single-ended into differential signals (balun) is needed. The most cited topology, which is capable of providing high gain, consists on a differential stage with one of the two inputs grounded. Unfortunately, this solution has some drawbacks when implemented monolithically. This work presents the design and simulated results of an innovative high-performance monolithic single to differential converter, which overcomes the limitations of the circuits.The integration of the monolithic active balun circuit with an LNA on a 0.18μm CMOS process is also reported. The circuits presented here are aimed at 802.11a. Section 2 describes the balun circuit and section 3 presents its performance when it is connected to a conventional single-ended LNA. Section 4 shows the simulated performance results focused at phase/amplitude balance and noise figure. Finally, the last section draws conclusions and future work.

A 5GHz1.8V Low Power CMOS Low-Noise Amplifier

Wireless local-area networks (WLANs) have been deployed as office and home communications infrastructures worldwide. The diversification of the standards, such as IEEE 802.11 series demands the design of RF front-ends. Low power consumption is one of the most important design concerns in the application of those technologies. To maintain competitive hardware costs, CMOS has been used since it is the best solution for low cost and high integration processing, allowing analog circuits to be mixed with digital ones. In the receiver chain, the low noise amplifier (LNA) is one of the most critical blocks in a transceiver design. The sensitivity is mainly determined by the LNA noise figure and gain. It interfaces with the pre-select filter and the mixer. Furthermore, since it is the first gain stage, care must be taken to provide accurate input match, low-noise figure, good linearity and a sufficient gain over a wide band of operation. Several CMOS LNAs have been reported during the last decade, showing that the most research has been done at 802.11/b and GSM standards (900-2400MHz spectrum) and more recently at 802.11/a (5GHz band). One of the more significant disadvantages of 802.11/b is that the frequency band is crowded and subject to interference from other technologies, as is 2.4GHz cordless phones and Bluetooth. As the demand for radio-frequency integrated circuits, operating at higher frequency bands, increases, the IEEE 802.11/a standard becomes a very attractive option to wireless communication system developers. This paper presents the design and implementation of a low power, low noise amplifier aimed at IEEE 802.11a for WLAN applications. It was designed to be integrated with an active balun and mixer, representing the first step toward a fully integrated monolithic WLAN receiver. All the required circuits are integrated at the same die and are powered by 1.8V supply source. Preliminary experimental results (S-parameters) are shown and promise excellent results. The LNA circuit design details are illustrated in Section 2. Spectre simulation results focused at gain, noise figure (NF) and input/output matching are presented in Section 3. Finally, conclusions and comparison with other recently reported LNAs are made in Section 4, followed by future work.

Practical Quality Control: Comparision of Methods on the Quantification of Stationary Phases in Paper and Thin-Layer Chromatographic Systems

Introduction: Paper and thin layer chromatography methods are frequently used in Classic Nuclear Medicine for the determination of radiochemical purity (RCP) on radiopharmaceutical preparations. An aliquot of the radiopharmaceutical to be tested is spotted at the origin of a chromatographic strip (stationary phase), which in turn is placed in a chromatographic chamber in order to separate and quantify radiochemical species present in the radiopharmaceutical preparation. There are several methods for the RCP measurement, based on the use of equipment as dose calibrators, well scintillation counters, radiochromatografic scanners and gamma cameras. The purpose of this study was to compare these quantification methods for the determination of RCP. Material and Methods: 99mTc-Tetrofosmin and 99mTc-HDP are the radiopharmaceuticals chosen to serve as the basis for this study. For the determination of RCP of 99mTc-Tetrofosmin we used ITLC-SG (2.5 x 10 cm) and 2-butanone (99mTc-tetrofosmin Rf = 0.55, 99mTcO4- Rf = 1.0, other labeled impurities 99mTc-RH RF = 0.0). For the determination of RCP of 99mTc-HDP, Whatman 31ET and acetone was used (99mTc-HDP Rf = 0.0, 99mTcO4- Rf = 1.0, other labeled impurities RF = 0.0). After the development of the solvent front, the strips were allowed to dry and then imaged on the gamma camera (256x256 matrix; zoom 2; LEHR parallel-hole collimator; 5-minute image) and on the radiochromatogram scanner. Then, strips were cut in Rf 0.8 in the case of 99mTc-tetrofosmin and Rf 0.5 in the case of 99mTc-HDP. The resultant pieces were smashed in an assay tube (to minimize the effect of counting geometry) and counted in the dose calibrator and in the well scintillation counter (during 1 minute). The RCP was calculated using the formula: % 99mTc-Complex = [(99mTc-Complex) / (Total amount of 99mTc-labeled species)] x 100. Statistical analysis was done using the test of hypotheses for the difference between means in independent samples. Results:The gamma camera based method demonstrated higher operator-dependency (especially concerning the drawing of the ROIs) and the measures obtained using the dose calibrator are very sensitive to the amount of activity spotted in the chromatographic strip, so the use of a minimum of 3.7 MBq activity is essential to minimize quantification errors. Radiochromatographic scanner and well scintillation counter showed concordant results and demonstrated the higher level of precision. Conclusions: Radiochromatographic scanners and well scintillation counters based methods demonstrate to be the most accurate and less operator-dependant methods.

Estudo hidráulico em modelo reduzido de descarregadores de cheias: utilização de conchas de rolo na dissipação de energia do escoamento

Dissertação para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização em Hidráulica

Circuitos neuronais entre estruturas corticais vs sub-corticais marcha humana

As conexões entre os níveis corticais e os níveis sub-corticais na activação da marcha Humana carecem de discussão. As alterações da marcha por lesão no território da Artéria Cerebral Média podem ser explicadas pela disfunção de circuitos neuronais dos Núcleos da Base ao córtex e Núcleos Pedúnculo-Pontinos, sendo para isso necessário identificar os percursos anatómicos das principais conexões entre as estruturas encefálicas referidas. Com base na topografia das conexões neuronais, é aceitável que as alterações da marcha possam existir também devido a alterações na função dos Núcleos da Base, através das suas conexões, enquanto moduladores da actividade motora.

O comportamento dos ajustes posturais antecipatórios na tibio-társica na sequência de levantar em indivíduos com doença de Parkinson

Introdução: A sequência de movimento de sentado para de pé (SPP) exige um elevado controlo postural (CP). Em indivíduos com doença de Parkinson (DP), os circuitos que envolvem os ajustes posturais antecipatórios (APA’s) parecem estar afetados, refletindo-se numa diminuição do CP com repercussões nesta sequência de movimento. Objetivo: Avaliar o comportamento dos APA’s na tibio-társica na sequência de movimento SPP em indivíduos com DP. Métodos: Recorreu-se ao estudo de 4 casos com DP, com tempo de evolução entre os 3 e 17 anos, objeto de uma intervenção de fisioterapia baseada nos princípios do Conceito de Bobath durante 12 semanas. Antes (M0) e após (M1) a intervenção procedeu-se ao registo eletromiográfico dos músculos tibial anterior (TA) e solear (SOL) bilateralmente e durante a sequência de SPP. Adicionalmente foram também utilizadas a Escala de Equilíbrio de Berg, a Modified Falls Efficacy Scale (MFES) e a Classificação Internacional de Funcionalidade (CIF), para, indiretamente, averiguar o impacto funcional da reorganização dos APA’s. Resultados: Em M0 os resultados sugerem uma diminuição APA’s, uma vez que se observou: 1) diferentes tempos de ativação do TA e do SOL entre membros e 2) uma ativação prévia do SOL ao TA para os participantes A, C e D. Em M1, observou-se uma aproximação ao comtemplado para os APA’s para a maioria dos indivíduos. Os resultados na escala de Berg e MFES, de M0 para M1, sugerem um aumento do equilíbrio e da capacidade de confiança na maioria dos participantes (A, 21/42 pontos, B manteve a pontuação final 31 pontos, C, 50/54 pontos e D 45/53 pontos na escala de Berg; A, 30/43 pontos, B, 21/18 pontos, C, 70/68 pontos e D, 40/64 pontos na MFES;). Também se observaram melhorias nas atividades e participação da CIF. Conclusão: nos indivíduos em estudo verificou-se, de uma forma geral, uma modificação no sentido da aproximação do período comtemplado para os APA’s, em M1. Nos sujeitos A, C, e D verificou-se uma modificação do tempo de activação do SOL em função da actividade do TA em M1. No individuo B, à esquerda não se verificou o mesmo comportamento, verificou-se a activação inversa do SOL ao TA.