Action of food preservatives on 14-days dental biofilm formation, biofilm vitality and biofilm-derived enamel demineralisation in situ

AIMS The aims of this double-blind, controlled, crossover study were to assess the influence of food preservatives on in situ dental biofilm growth and vitality, and to evaluate their influence on the ability of dental biofilm to demineralize underlying enamel over a period of 14 days. MATERIALS AND METHODS Twenty volunteers wore appliances with six specimens each of bovine enamel to build up intra-oral biofilms. During four test cycles of 14 days, the subjects had to place the appliance in one of the assigned controls or active solutions twice a day for a minute: negative control 0.9 % saline, 0.1 % benzoate (BA), 0.1 % sorbate (SA) and 0.2 % chlorhexidine (CHX positive control). After 14 days, the biofilms on two of the slabs were stained to visualize vital and dead bacteria to assess biofilm thickness (BT) and bacterial vitality (BV). Further, slabs were taken to determine mineral loss (ML), by quantitative light-induced laser fluorescence (QLF) and transversal microradiography (TMR), moreover the lesion depths (LD). RESULTS Nineteen subjects completed all test cycles. Use of SA, BA and CHX resulted in a significantly reduced BV compared to NaCl (p < 0.001). Only CHX exerted a statistically significant retardation in BT as compared to saline. Differences between SA and BA were not significant (p > 0.05) for both parameters. TMR analysis revealed the highest LD values in the NaCl group (43.6 ± 44.2 μm) and the lowest with CHX (11.7 ± 39.4 μm), while SA (22.9 ± 45.2 μm) and BA (21.4 ± 38.5 μm) lay in between. Similarly for ML, the highest mean values of 128.1 ± 207.3 vol% μm were assessed for NaCl, the lowest for CHX (-16.8 ± 284.2 vol% μm), while SA and BA led to values of 83.2 ± 150.9 and 98.4 ± 191.2 vol% μm, respectively. With QLF for both controls, NaCl (-33.8 ± 101.3 mm(2) %) and CHX (-16.9 ± 69.9 mm(2) %), negative values were recorded reflecting a diminution of fluorescence, while positive values were found with SA (33.9 ± 158.2 mm(2) %) and BA (24.8 ± 118.0 mm(2) %) depicting a fluorescence gain. These differences were non-significant (p > 0.05). CONCLUSION The biofilm model permited the assessment of undisturbed oral biofilm formation influenced by antibacterial components under clinical conditions for a period of 14 days. An effect of BA and SA on the demineralization of enamel could be demonstrated by TMR and QLF, but these new findings have to be seen as a trend. As part of our daily diet, these preservatives exert an impact on the metabolism of the dental biofilm, and therefore may even influence demineralization processes of the underlying dental enamel in situ.

A Biofilm Pocket Model to Evaluate Different Non-Surgical Periodontal Treatment Modalities in Terms of Biofilm Removal and Reformation, Surface Alterations and Attachment of Periodontal Ligament Fibroblasts.

BACKGROUND AND AIM There is a lack of suitable in vitro models to evaluate various treatment modalities intending to remove subgingival bacterial biofilm. Consequently, the aims of this in vitro-study were: a) to establish a pocket model enabling mechanical removal of biofilm and b) to evaluate repeated non-surgical periodontal treatment with respect to biofilm removal and reformation, surface alterations, tooth hard-substance-loss, and attachment of periodontal ligament (PDL) fibroblasts. MATERIAL AND METHODS Standardized human dentin specimens were colonized by multi-species biofilms for 3.5 days and subsequently placed into artificially created pockets. Non-surgical periodontal treatment was performed as follows: a) hand-instrumentation with curettes (CUR), b) ultrasonication (US), c) subgingival air-polishing using erythritol (EAP) and d) subgingival air-polishing using erythritol combined with chlorhexidine digluconate (EAP-CHX). The reduction and recolonization of bacterial counts, surface roughness (Ra and Rz), the caused tooth substance-loss (thickness) as well as the attachment of PDL fibroblasts were evaluated and statistically analyzed by means of ANOVA with Post-Hoc LSD. RESULTS After 5 treatments, bacterial reduction in biofilms was highest when applying EAP-CHX (4 log10). The lowest reduction was found after CUR (2 log10). Additionally, substance-loss was the highest when using CUR (128±40 µm) in comparison with US (14±12 µm), EAP (6±7 µm) and EAP-CHX (11±10) µm). Surface was roughened when using CUR and US. Surfaces exposed to US and to EAP attracted the highest numbers of PDL fibroblasts. CONCLUSION The established biofilm model simulating a periodontal pocket combined with interchangeable placements of test specimens with multi-species biofilms enables the evaluation of different non-surgical treatment modalities on biofilm removal and surface alterations. Compared to hand instrumentation the application of ultrasonication and of air-polishing with erythritol prevents from substance-loss and results in a smooth surface with nearly no residual biofilm that promotes the reattachment of PDL fibroblasts.

Fluoride varnishes with calcium glycerophosphate: fluoride release and effect on in vitro enamel demineralization

The aims of this study were (1) to assess the amount of fluoride (F) released from varnishes containing calcium glycerophosphate (CaGP) and (2) to assess the effect of the experimental varnishes on in vitro demineralization. Six test groups using 5 varnishes: base varnish (no active ingredients); Duraphat® (2.26% NaF); Duofluorid® (5.63% NaF/CaF2); experimental varnish 1 (1% CaGP/5.63% NaF/CaF2); experimental varnish 2 (5% CaGP/5.63% NaF/CaF2); and no varnish were set up. In stage 1, 60 acrylic blocks were randomly distributed into 6 groups (n = 10). Then 300 µg of each varnish was applied to each block. The blocks were immersed in deionized water, which was changed after 1, 8, 12, 24, 48 and 72 hours. Fluoride concentration in the water was analyzed using a fluoride electrode. In stage 2, 60 bovine enamel samples were distributed into 6 groups (n = 10), and treated with 300 µg of the respective varnish. After 6 h the varnish was removed and the samples were subjected to a 7-day in vitro pH cycle (6 h demineralization/18 h remineralization per day). The demineralization was measured using surface hardness. The results showed that both experimental varnishes released more fluoride than Duofluorid® and Duraphat® (p < 0.05), but Duraphat® showed the best preventive effect by decreasing enamel hardness loss (p < 0.05). Therefore, we conclude that even though (1) the experimental varnishes containing CaGP released greater amounts of F, (2) they did not increase in the preventive effect against enamel demineralization.

Fluoride varnishes containing calcium glycerophosphate: fluoride uptake and the effect on in vitro enamel erosion

OBJECTIVES Calcium glycerophosphate (CaGP) was added to fluoride varnishes to analyze their preventive effect on initial enamel erosion and fluoride uptake: potassium hydroxide (KOH)-soluble and KOH-insoluble fluoride bound to enamel. MATERIALS AND METHODS This study was carried out in two parts. Part 1: 108 enamel samples were randomly distributed into six varnish groups: base varnish (no active ingredients); Duraphat® (2.26 %NaF); Duofluorid® (5.63 %NaF/CaF2); experimental varnish 1 (1 %CaGP/5.63 %NaF/CaF2); experimental varnish 2 (5 %CaGP/5.63 %NaF/CaF2); and no varnish. Cyclic demineralization (90 s; citric acid, pH = 3.6) and remineralization (4 h) was made once a day, for 3 days. Change in surface microhardness (SMH) was measured. Part 2: 60 enamel samples were cut in half and received no varnish (control) or a layer of varnish: Duraphat®, Duofluorid®, experimental varnishes 1 and 2. Then, KOH-soluble and KOH-insoluble fluoride were analyzed using an electrode. RESULTS After cyclic demineralization, SMH decreased in all samples, but Duraphat® caused less hardness loss. No difference was observed between varnishes containing CaGP and the other varnishes. Similar amounts of KOH-soluble and insoluble fluoride was found in experimental varnish 1 and Duofluorid®, while lower values were found for experimental varnish 2 and Duraphat®. CONCLUSION The addition of CaGP to fluoride varnishes did not increase fluoride bound to enamel and did not enhance their protection against initial enamel erosion. CLINICAL RELEVANCE We observe that the fluoride varnishes containing CaGP do not promote greater amounts of fluoride bound to enamel and that fluoride bound to enamel may not be closely related to erosion prevention.

Effectiveness of meticillin-resistant Staphylococcus aureus decolonization in long-term haemodialysis patients: a systematic review and meta-analysis.

BACKGROUND Chronic haemodialysis patients are a high-risk population for meticillin-resistant Staphylococcus aureus (MRSA) colonization, which is a precursor of infection. AIM To summarize the effect of nasal (± whole-body wash) MRSA decolonization in haemodialysis patients by means of a systematic review and meta-analysis. METHODS We identified eligible studies using Medline, Embase, the Cochrane database, clinicaltrials.org, and conference abstracts investigating the success of MRSA decolonization in haemodialysis patients. For the statistical analysis, we used Stata 13 to express study-specific proportions with 95% confidence intervals. A likelihood ratio test was used to assess inter-study heterogeneity. FINDINGS Six published prospective cohort studies and one study described in a conference abstract met our inclusion criteria. From 1150 haemodialysis patients enrolled in these studies, MRSA was isolated from nasal swabs of 147 (12.8%) patients. Six of the trials used mupirocin nasal ointment and combined it with chlorhexidine body washes for decolonization. The most widely used protocol was a five-day course of mupirocin nasal ointment application three times a day, and chlorhexidine body wash once daily. The pooled success rate of decolonization was 0.88 (95% confidence interval: 0.75-0.95). A likelihood ratio test of the fixed versus the random-effects model showed significant inter-study heterogeneity (P = 0.047). Four of seven studies determined subsequent MRSA infections in 94 carriers overall, two (2%) of which experienced infection. CONCLUSION The use of mupirocin together with whole-body decolonization is highly effective in eradicating MRSA carriage in haemodialysis patients. The current literature, however, is characterized by a lack of comparative effectiveness studies for this intervention.

Effects of Antiseptic Solutions Commonly Used in Dentistry on Bone Viability, Bone Morphology, and Release of Growth Factors

PURPOSE Antiseptic solutions are commonly used in dentistry for a number of sterilization procedures, including harvesting of bone chips, irrigation of extraction sockets, and sterilization of osteonecrotic bone. Despite its widespread use, little information is available regarding the effects of various antiseptic solutions on bone cell viability, morphology, and the release of growth factors. MATERIALS AND METHODS The antiseptic solutions included 1) 0.5% povidone iodine (PI), 2) 0.2% chlorhexidine diguluconate (CHX), 3) 1% hydrogen peroxide (H2O2), and 4) 0.25% sodium hypochlorite (HYP). Bone samples collected from porcine mandibular cortical bone were rinsed in the antiseptic solutions for 10 minutes and assessed for cell viability using an MTS assay and protein release of transforming growth factor (TGF-β1), bone morphogenetic protein 2 (BMP2), vascular endothelial growth factor (VEGF), interleukin (IL)-1β, and receptor activator of nuclear factor κB ligand (RANKL) using an enzyme-linked immunosorbent assay at 15 minutes and 4 hours after rinsing. RESULTS After antiseptic rinsing, changes to the surface protein content showed marked alterations, with an abundant protein layer remaining on CHX-rinsed bone samples. The amount of surface protein content gradually decreased in the following order: CHX, H2O2, PI, and HYP. A similar trend was also observed for the relative cell viability from within bone samples after rinsing, with up to 6 times more viable cells found in the CHX-rinsed bone samples than in the HYP- and PI-rinsed samples. An analysis of the growth factors found that both HYP and PI had significantly lower VEGF and TGF-β1 protein release from bone samples at 15 minutes and 4 hours after rinsing compared with CHX and H2O2. A similar trend was observed for RANKL and IL-1β protein release, although no change was observed for BMP2. CONCLUSIONS The results from the present study have demonstrated that antiseptic solutions present with very different effects on bone samples after 10 minutes of rinsing. Rinsing with CHX maintained significantly higher cell viability and protein release of growth factors potent to the bone remodeling cycle.

Influence of root canal disinfectants on growth factor release from dentin

INTRODUCTION During dentinogenesis, growth factors become entrapped in the dentin matrix that can later be released by demineralization. Their effect on pulpal stem cell migration, proliferation, and differentiation could be beneficial for regenerative endodontic therapies. However, precondition for success, as for conventional root canal treatment, will be sufficient disinfection of the root canal system. Various irrigation solutions and intracanal dressings are available for clinical use. The aim of this study was 2-fold: to identify a demineralizing solution suitable for growth factor release directly from dentin and to evaluate whether commonly used disinfectants for endodontic treatment will compromise this effect. METHODS Dentin disks were prepared from extracted human teeth and treated with EDTA or citric acid at different concentrations or pH for different exposure periods. The amount of transforming growth factor-β1 (TGF-β1), fibroblast growth factor 2, and vascular endothelial growth factor were quantified via enzyme-linked immunosorbent assay and visualized by gold labeling. Subsequently, different irrigation solutions (5.25% sodium hypochloride, 0.12% chlorhexidine digluconate) and intracanal dressings (corticoid-antibiotic paste, calcium hydroxide: water-based and oil-based, triple antibiotic paste, chlorhexidine gel) were tested, and the release of TGF-β1 was measured after a subsequent conditioning step with EDTA. RESULTS Conditioning with 10% EDTA at pH 7 rendered the highest amounts of TGF-β1 among all test solutions. Fibroblast growth factor 2 and vascular endothelial growth factor were detected after EDTA conditioning at minute concentrations. Irrigation with chlorhexidine before EDTA conditioning increased TGF-β1 release; sodium hypochloride had the opposite effect. All tested intracanal dressings interfered with TGF-β1 release except water-based calcium hydroxide. CONCLUSIONS Growth factors can be released directly from dentin via EDTA conditioning. The use of disinfecting solutions or medicaments can amplify or attenuate this effect.

Management of a complication with a fractured zirconia implant abutment in the esthetic zone

Technical complications in implant prosthetic cases represent a major challenge in dentistry. This case report describes minimally invasive management to recover an implant with a fractured remnant of a zirconia abutment, including provisional rehabilitation during a sequential treatment protocol in the esthetic zone. A patient was treated with a screw-retained one-piece implant-supported reconstruction made of a customized zirconia abutment with direct ceramic veneering in the maxillary right central incisor position. During the prosthetic try-in, a fracture in the apical portion of the abutment was evident. The first rescue attempt led to fracture of the retrieval instrument. Immediately, an individualized wired construction was applied to bond the existing fractured reconstruction to the neighboring teeth to maintain the peri-implant mucosal architecture. Because the implant screw canal was blocked, a customized round bur had to be manufactured and was placed in the implant axis with a specific bracket tool from the service set to protect the interior implant threads. Then, the drills of the service set were guided by the newly created access to remove the fractured remnants. The implant screw was retapped and the area rinsed with chlorhexidine solution. All remnants were removed without the need for surgical intervention. Neither the implant connection nor the bone-to-implant interface was damaged. The stepwise treatment approach with the customized round bur combined with the system-specific drills of the service set saved the blocked implant so that the patient could be successfully rehabilitated with a new implant reconstruction.

Significant Differences Characterise the Correlation Coefficients between Biocide and Antibiotic Susceptibility Profiles in Staphylococcus aureus.

There is a growing concern by regulatory authorities for the selection of antibiotic resistance caused by the use of biocidal products. We aimed to complete the detailed information on large surveys by investigating the relationship between biocide and antibiotic susceptibility profiles of a large number of Staphylococcus aureus isolates using four biocides and antibiotics commonly used in clinical practice. The minimal inhibitory concentration (MIC) for most clinically-relevant antibiotics was determined according to the standardized methodology for over 1600 clinical S. aureus isolates and compared to susceptibility profiles of benzalkonium chloride, chlorhexidine, triclosan, and sodium hypochlorite. The relationship between antibiotic and biocide susceptibility profiles was evaluated using non-linear correlations. The main outcome evidenced was an absence of any strong or moderate statistically significant correlation when susceptibilities of either triclosan or sodium hypochlorite were compared for any of the tested antibiotics. On the other hand, correlation coefficients for MICs of benzalkonium chloride and chlorhexidine were calculated above 0.4 for susceptibility to quinolones, beta-lactams, and also macrolides. Our data do not support any selective pressure for association between biocides and antibiotics resistance and furthermore do not allow for a defined risk evaluation for some of the compounds. Importantly, our data clearly indicate that there does not involve any risk of selection for antibiotic resistance for the compounds triclosan and sodium hypochlorite. These data hence infer that biocide selection for antibiotic resistance has had so far a less significant impact than feared.

A systematic review examining the relationship between oral health care practices and the oral lesions commonly associated with HIV/AIDS, and the implications for people living in developing countries

Oral lesions, which may be bacterial, fungal or viral in nature may be characteristic of HIV/ AIDS, and have been observed on the oral mucosa as early signs of underlying disease. Some studies have suggested that there may be a correlation between poor oral hygiene, and the oral lesions seen among people living with HIV/AIDS.^ The objective of this study was to assess the nature of the relationship between oral health care practices, and the occurrence of oral lesions commonly seen in association with HIV/AIDS. A systematic review of the literature was conducted, and the databases searched were Medline and PubMed. Concepts that made up the search were oral hygiene promotion, HIV/AIDS and oral health care. Out of the 410 items identified through the search, only 11 met the inclusion criteria.^ The use of 0.12%–2% chlorhexidine gluconate, was found to be effective in reducing oral Candida counts in some studies, while other studies did not find such an association. However, 0.12%–2% chlorhexidine gluconate was consistently found to be effective in the management of periodontal lesions in people infected with HIV/AIDS. ^ Dental procedures such as treatment and filling of dental cavities, scaling and polishing, and use of fluoridated tooth paste were also found to be effective in the management of oral lesions seen in association with HIV/AIDS.^ The overall findings from the studies reviewed, suggest that effective oral health care may be necessary to reduce the morbidity, and mortality associated with the oral lesions seen among people living with HIV/AIDS. However, better designed studies with larger sample sizes need to be developed in order to ascertain the effectiveness of routine oral hygiene, and health care practices among people living with HIV/AIDS.^

Producción de barniz de base alquídica

El presente trabajo contiene el análisis y la evaluación técnico económica de la fabricación de barniz a nivel industrial. El estudio realizado alcanza el nivel de prefactibilidad. El producto barniz es de tipo bien intermedio, utilizado en un importante número de aplicaciones, mayormente para los recubrimientos en la industria automotriz y de la construcción. El tamaño propuesto para la planta fue determinado a partir del análisis y consideración de las siguientes variables: tecnologías aplicables, disponibilidad de insumos, mercado potencial a sustituir, tasa de descuento de referencia y requerimientos de gestión

(Table 3) Age-related trends of desert pavement properties in the Transantarctic Mountains

Compared to mid-latitude deserts, the properties, formation and evolution of desert pavements and the underlying vesicular layer in Antarctica are poorly understood. This study examines the desert pavements and the vesicular layer from seven soil chronosequences in the Transantarctic Mountains that have developed on two contrasting parent materials: sandstone-dolerite and granite-gneiss. The pavement density commonly ranges from 63 to 92% with a median value of 80% and does not vary significantly with time of exposure or parent material composition. The dominant size range of clasts decreases with time of exposure, ranging from 16-64 mm on Holocene and late Quaternary surfaces to 8-16 mm on surfaces of middle Quaternary and older age. The proportion of clasts with ventifaction increases progressively through time from 20% on drifts of Holocene and late Quaternary age to 35% on Miocene-aged drifts. Desert varnish forms rapidly, especially on dolerite clasts, with nearly 100% cover on surfaces of early Quaternary and older age. Macropitting occurs only on clasts that have been exposed since the Miocene. A pavement development index, based on predominant clast-size class, pavement density, and the proportion of clasts with ventifaction, varnish, and pits, readily differentiated pavements according to relative age. From these findings we judge that desert pavements initially form from a surficial concentration of boulders during till deposition followed by a short period of deflation and a longer period of progressive chemical and physical weathering of surface clasts. The vesicular layer that underlies the desert pavement averages 4 cm in thickness and is enriched in silt, which is contributed primarily by weathering rather than eolian deposition. A comparison is made between desert pavement properties in mid-latitude deserts and Antarctic deserts.

Influencias de los barnices incoloros en las propiedades superficiales de las maderas de construcción

En esta Tesis se cuantifica la variación cromática que producen los barnices en el color de los diferentes tipos de maderas de construcción, obteniendo un modelo matemático de predicción de color de la madera. Se analizan las prestaciones de dieciséis barnices, supuestamente incoloros, aplicados sobre veinte tipos de maderas, angiospermas y gimnospermas, de distintas densidades y latitudes. Ambos materiales son de uso frecuente en el ámbito de la construcción y de fácil localización en las tiendas y almacenes de ambos sectores. Se utilizan técnicas de descomposición cromática, mediante el empleo de microscopio óptico de reflexión, para poder obtener un abanico gráfico de histogramas con valores numéricos de luminosidad y composición cromática, y de esta forma comprobar que los supuestos barnices que se venden como incoloros, no son totalmente incoloros sino que muestran tendencias a virar hacia alguno de los colores básicos. En el proceso experimental de la Tesis, se aplican 16 barnices sobre 20 tipos de maderas, obteniéndose los histogramas de las campañas de fotografías realizadas con cinco años de diferencia, obteniéndose no solo la variación de color que producen los barnices sobre el original de la madera, sino además la influencia de un envejecimiento a los cinco años. La Tesis relaciona el tipo de barniz idóneo para cada tipo de madera, de modo que produzca la menor variación cromática. La Tesis además obtiene un modelo matemático que permite predecir el color final de la madera tratada en función del color inicial de la madera sin barnizar. Se propone en esta Tesis una recomendación de los productos a utilizar en cada uno de los tipos de madera en base a su color inicial. This Thesis quantifies the chromatic variation caused by varnishes in the colour of different types of timbers, obtaining a mathematical model for predicting the timber’s colour. The performance of sixteen varnishes, supposedly colourless, is analysed, applied on twenty types of timber, angiosperms and gymnosperms, of different densities and latitudes. Both materials are of frequent use in the construction field and easily located in the stores and warehouses of both sectors. Chromatic decomposition techniques are used, through the utilization of a reflection optical microscope, in order to obtain a graphic range of histograms with numerical values of luminosity and chromatic composition, and this way confirm that the alleged varnishes sold as colourless are not completely colourless but are prone to shift towards one of the basic colours. During the Thesis’ experimental procedure 16 varnishes are applied on 20 types of timber, obtaining the colour histograms of the photography campaigns carried out with a five years difference, resulting in not only the colour variation caused by the varnishes on the original timber, but also the influence of its ageing five years later. The Thesis links the right type of varnish for each kind of timber, so that as little chromatic variation as possible occurs. The Thesis obtains as well a mathematical model, which makes it possible to predict the final colour of the treated timber depending on the original colour of the timber with no varnish. This Thesis proposes a recommendation of the products to use on each type of timber on the basis of its original colour.

Corrosión inducida por contaminantes hidrosolubles en la intercara metal/pintura

El objetivo principal de este trabajo es profundizar en el conocimiento del fenómeno de la corrosión subpelicular inducida por contaminantes hidrosolubles en la intercara metal/pintura. La contaminación salina del substrato es una situación común en la práctica: la superficie metálica suele estar expuesta a atmósferas contaminadas antes de ser recubierta, limpieza previa del metal con abrasivos contaminados, etc. La eliminación total de estos contaminantes resulta muy difícil de conseguir incluso con las técnicas más sofisticadas de limpieza. Esta investigación se centra en la determinación del efecto de la naturaleza del contaminante y la naturaleza y espesor del recubrimiento en el proceso de corrosión subpelicular del acero. En la investigación se utilizaron dos barnices de naturaleza diferente: poliuretano y vinílico; y se aplicaron a tres espesores diferentes. Los contaminantes empleados en este trabajo fueron: NaCl, NH4C1, CaCl2, Na2S04, (NH4)2S04, NaN03, NH4N03, Ca(N03)2. Los ensayos se realizaron en una cámara de condensación de humedad permanente. Los tiempos de exposición fueron 100, 300 y 600 horas. La velocidad de corrosión se evaluó gravimétricamente, mediante la técnica de pérdida de peso. Se realizaron estudios de permeabilidad al oxígeno y al agua de películas libres de substrato, evaluación de la velocidad de corrosión de probetas sin pintar inmersas en soluciones salinas de los contaminantes seleccionados, conductividad de dichas soluciones salinas, solubilidad del oxígeno en las soluciones salinas, adherencia en seco y en húmedo a diferentes tiempos de exposición. Se aporta evidencia respecto al control ejercido en el proceso corrosivo por el oxígeno que permea a través de la película, mientras que la permeación de agua controla la pérdida de adherencia del recubrimiento. Ambas permeabilidades dependen de la naturaleza del recubrimiento y de su espesor. Se ha investigado la influencia de la naturaleza del contaminante en la intercara metal/pintura. La naturaleza del catión parece quedar enmascarada por el efecto definitivo del anión. La concentración salina ejerce asimismo un efecto importante en la corrosión subpelicular. ABSTRACT The main aim of this work is to study in depth the knowledge of underfilm corrosión induced by hydrosoluble contaminants at the metal/paint Ínterface. The saline contamination of the substrate is a common situation in practice: metallic surfaces use to be exposed to polluted atmospheres, previous cleaning of the metal with contaminated abrasives, etc. Total elimination of these contaminants is hard to obtain even with modern cleaning techniques. This research is focused in determining the effect of contaminant nature, coating nature and its thickness on the steel underfilm corrosión process. In this work we used two varnishes with different nature: polyurethane and vinyl; they were applied in three different thicknesses. The saline contaminants employed were: NaCl, NH4C1, CaCl2, Na2S04, (NH4)2S04, NaN03, NH4N03/ Ca(N03)2. The tests were carried out in a condensation humidity chamber. The period of exposure were 100, 300 and 600 hours. Corrosión rate was assessed by weight loss. Simultaneously, studies on oxygen and water permeability of free films, assessing on corrosión rate of uncoated samples immersed in saline solutions of the selected contaminants, conductivity of these solutions, oxygen solubility in saline solutions, wet and dry adhesión of the polyurethane varnish at different periods of exposure, were carried out. There is clear evidence about control on corrosión process of oxygen that passes through the coating, while the passing of water controls the loss of adhesión of the coating. Both, water and oxygen permeation, depend on the nature and thickness of the coating. It has been researched the inf luence of the nature of contaminant at the metal/paint interface. The nature of the catión seems to be "masked" by the definitive effect of the nature of anión. The saline concentration also exerts an important effect on underfilm corrosión.

Objetos tenaces : adaptive reuse en Meatpacking, 1970–1985

OBJETOS TENACES versa sobre la práctica del adaptive reuse (la “reutilización adaptativa”, la reconversión) explicado a través del fenómeno de ruptura, suspensión y reconfiguración de vínculos que el objeto arquitectónico tiene con respecto a su medio económico, sociocultural, normativo y de utilitas. Se trata de un fenómeno en tres fases, muy próximo al mecanismo empleado por el readymade y por el display, que en arquitectura parte de la crisis que supone un cambio de circunstancias, un desarraigo del objeto respecto de su ámbito anterior. El mecanismo tiene vocación de intervención mínima, desde un posicionamiento actual que comprende el mundo construido como una realidad “ya hecha”, y donde las operaciones de proyecto son acciones de transformación que llevan de una situación de obsolescencia a otra de vigencia renovada, es decir, de una realidad completa a otra igualmente completa. Para ello, la investigación se sirve de tres ejemplos de un mismo entorno geográfico (el área en torno a Meatpacking, en el lado oeste del bajo Manhattan, Nueva York) y temporal (las últimas décadas del siglo XX, en las que los casos se solapan a pesar de tener desarrollos cronológicos diversos). Bell Telephone Laboratories, The West Side Improvement y The National Biscuit Company, reconvertidos a Westbeth, a The High Line y a Chelsea Market, construyen juntos el argumento por suma de conceptos, por adición de fenómenos, estudiando las cualidades y las circunstancias que hacen posible la continuidad de las estructuras, es decir, su supervivencia. El texto forma un corpus que proporciona algunas de las claves del objeto denominado como tenaz a través del análisis sincrónico del antes y el después de su puesta en crisis. A tal efecto, se exponen una serie de figuras razonadas entre las cuales figuran el lijado del barniz, los hilos compartidos, la máscara, la momificación y la vitrina, el puente sobre le desfiladero, el enfriamiento, o las reliquias, incrustaciones y adherencias, todas ellas encaminadas a explicar el proceso de renovación del artefacto como un cambio en el sentido, en el significado, y no tanto en lo material. Entre las consideraciones de la tesis está, por un lado, el carácter relativo del término tenacidad, concepto que define a los objetos que se encuentran y se reconocen en su idoneidad, que tienen capacidad de adaptación, y que precisan finalmente de grandes dosis de pragmatismo para su reconfiguración, siendo todas éstas condiciones necesarias pero sólo suficientes a posteriori. Por otro lado, el texto reflexiona acerca del intangible que comparten todos los objetos así llamados y que consiste en la condición, quizá formidable, de ser reconocibles por parte de los sucesivos intervinientes de su historia, convencidos de que su renovación supone una oportunidad; su desaparición, una pérdida. Finalmente, la investigación apunta hacia el concepto de anacronismo como justificación para los objetos que se demuestran adaptables a épocas sucesivas, y que encajan en el tiempo de forma compleja. ABSTRACT TENACIOUS OBJECTS deals with the practice of the adaptive reuse explained by means of the phenomenon of rupture, suspension and reconfiguration of links that the architectural object has vis-à-vis its economic, socio-cultural and regulatory environment, and its utilitas. It is a phenomenon structured in three stages, very close to the mechanism used by the readymade and by the display, which in architecture arise from the crisis that leads to a change in circumstances, an alienation of the object regarding its previous environment. The mechanism aims to the minimum intervention, from a current positioning which understands the world built as a reality “already made”, and where the operations of the project are transformative actions that take us from a situation of obsolescence to a situation of renewed validity, that is, from a complete reality to one just as complete. For this purpose, the research makes use of three examples in the same geographical area (the Meatpacking Discrict, in the Lower West Side of Manhattan, New York) and the same period (the last decades of the 20th century, in which the cases overlap in spite of their diverse chronological developments). Bell Telephone Laboratories, The West Side Improvement and The National Biscuit Company, reconverted into Westbeth, The High Line and Chelsea Market, make up, together, the argument as a sum of concepts, and addition of phenomena, studying the qualities and circumstances which make the continuity of the structures possible, that is, their survival. The text forms a corpus that provides some of the keys of the so-called tenacious object by means of the synchronic analysis of before and after its crisis. To this end, a series of reasoned figures is presented, including the sanding of varnish, the shared threads, the mask, the mummification and the display cabinet, the bridge over the gorge, cooling, or the relics, incrustations and adherences, all of them aimed at explaining the renovation process of the artifact as a change in the sense and the meaning, rather than the material. The considerations of this dissertation include, on the one hand, the relative nature of the term tenacity, a concept which defines the objects found and recognized in their suitability, that are capable of adapting and which finally require large doses of pragmatism for their reconfiguration, all these conditions being necessary but only sufficient a posteriori. On the other hand, the text reflects on the intangible shared among all the so-called objects, and which consists of the condition, perhaps extraordinary, of being recognized by the subsequent interveners of their history, convinced that their renovation represents an opportunity; their disappearance, a loss. Finally, the dissertation studies the concept of anachronism as a justification for the objects that prove to adapt to subsequent periods, and which fit in time in a complex manner.