First day of an oil spill on the open sea: early mass transfers of hydrocarbons to air and water.

During the first hours after release of petroleum at sea, crude oil hydrocarbons partition rapidly into air and water. However, limited information is available about very early evaporation and dissolution processes. We report on the composition of the oil slick during the first day after a permitted, unrestrained 4.3 m(3) oil release conducted on the North Sea. Rapid mass transfers of volatile and soluble hydrocarbons were observed, with >50% of ≤C17 hydrocarbons disappearing within 25 h from this oil slick of <10 km(2) area and <10 μm thickness. For oil sheen, >50% losses of ≤C16 hydrocarbons were observed after 1 h. We developed a mass transfer model to describe the evolution of oil slick chemical composition and water column hydrocarbon concentrations. The model was parametrized based on environmental conditions and hydrocarbon partitioning properties estimated from comprehensive two-dimensional gas chromatography (GC×GC) retention data. The model correctly predicted the observed fractionation of petroleum hydrocarbons in the oil slick resulting from evaporation and dissolution. This is the first report on the broad-spectrum compositional changes in oil during the first day of a spill at the sea surface. Expected outcomes under other environmental conditions are discussed, as well as comparisons to other models.

Low molecular weight carboxylic acids in oxidizing porphyry copper tailings

The distribution of low molecular weight carboxylic acids (LMWCA) was investigated in pore water profiles from two porphyry copper tailings impoundments in Chile (Piuquenes at La Andina and Cauquenes at El Teniente mine). The objectives of this study were (1) to determine the distribution of LMWCA, which are interpreted to be the metabolic byproducts of the autotroph microbial community in this low organic carbon system, and (2) to infer the potential role of these acids in cycling of Fe and other elements in the tailings impoundments. The speciation and mobility of iron, and potential for the release of H+ via hydrolysis of the ferric iron, are key factors in the formation of acid mine drainage in sulfidic mine wastes. In the low-pH oxidation zone of the Piuquenes tailings, Fe(III) is the dominant iron species and shows high mobility. LMWCA, which occur mainly between the oxidation front down to 300 cm below the tailings surface at both locations (e.g., max concentrations of 0.12 mmol/L formate, 0.17 mmol/L acetate, and 0.01 mmol/L pyruvate at Piuquenes and 0.14 mmol/L formate, 0.14 mmol/L acetate, and 0.006 mmol/L pyruvate at Cauquenes), are observed at the same location as high Fe concentrations (up to 71.2 mmol/L Fe(II) and 16.1 mmol/L Fe(III), respectively). In this zone, secondary Fe(111) hydroxides are depleted. Our data suggest that LMWCA may influence the mobility of iron in two ways. First, complexation of Fe(III), through formation of bidentate Fe(III)-LMWCA complexes (e.g., pyruvate, oxalate), may enhance the dissolution of Fe(III) (oxy)hydroxides or may prevent precipitation of Fe(III) (oxy)hydroxides. Soluble Fe(III) chelate complexes which may be mobilized downward and convert to Fe(II) by Fe(III) reducing bacteria. Second, monodentate LMWCA (e.g., acetate and formate) can be used by iron-reducing bacteria as electron donors (e.g., Acidophilum spp.), with ferric iron as the electron acceptor. These processes may, in part, explain the low abundances of secondary Fe(III) hydroxide precipitates below the oxidation front and the high concentrations of Fe(II) observed in the pore waters of some low-sulfide systems. The reduction of Fe(III) and the subsequent increase of iron mobility and potential acidity transfer (Fe(II) oxidation can result in the release of H+ in an oxic environment) should be taken in account in mine waste management strategies.

Further insights on dynamic morphological transitions in quasi-two-dimensional electrodeposition

Dynamic morphological transitions in thin-layer electrodeposits obtained from copper sulphate solutions have been studied. The chemical composition of the electrodeposits indicates that they appear as a consequence of the competition between copper and cuprous oxide formation. In addition, the Ohmic control of the process is verified at initial stages of the deposit growth. At higher deposit developments, gravity-induced convection currents play a role in the control of the whole process and affect the position of these transitions.

Use of nanoparticles in Swiss industry: a targeted survey

A large number of applications using manufactured nanoparticles of less than 100 nm are currently being introduced into industrial processes. There is an urgent need to evaluate the risks of these novel particles to ensure their safe production, handling, use, and disposal. However, today we lack even rudimentary knowledge about type and quantity of industrially used manufactured nanoparticles and the level of exposure in Swiss industry. The goal of this study was to evaluate the use of nanoparticles, the currently implemented safety measures, and the number of potentially exposed workers in all types of industry. To evaluate this, a targeted telephone survey was conducted among health and safety representatives from 197 Swiss companies. The survey showed that nanoparticles are already used in many industrial sectors; not only in companies in the new field of nanotechnology, but also in more traditional sectors, such as paints. Forty-three companies declared to use or produce nanoparticles, and 11 imported and traded with prepackaged goods that contain nanoparticles. The following nanoparticles were found to be used in considerable quantities (> 1000 kg/year per company): Ag, Al-Ox, Fe-Ox, SiO2, TiO2, and ZnO. The median reported quantity of handled nanoparticles was 100 kg/year. The production of cosmetics, food, paints, powders, and the treatment of surfaces used the largest quantities of these nanoparticles. Generally, the safety measures were found to be higher in powder-based than in liquid-based applications. However, the respondents had many open questions about best practices, which points to the need for rapid development of guidelines and protection strategies

Advanced geostatistical and machine-learning models for spatial data analysis of radioactively contaminated regions

Radioactive soil-contamination mapping and risk assessment is a vital issue for decision makers. Traditional approaches for mapping the spatial concentration of radionuclides employ various regression-based models, which usually provide a single-value prediction realization accompanied (in some cases) by estimation error. Such approaches do not provide the capability for rigorous uncertainty quantification or probabilistic mapping. Machine learning is a recent and fast-developing approach based on learning patterns and information from data. Artificial neural networks for prediction mapping have been especially powerful in combination with spatial statistics. A data-driven approach provides the opportunity to integrate additional relevant information about spatial phenomena into a prediction model for more accurate spatial estimates and associated uncertainty. Machine-learning algorithms can also be used for a wider spectrum of problems than before: classification, probability density estimation, and so forth. Stochastic simulations are used to model spatial variability and uncertainty. Unlike regression models, they provide multiple realizations of a particular spatial pattern that allow uncertainty and risk quantification. This paper reviews the most recent methods of spatial data analysis, prediction, and risk mapping, based on machine learning and stochastic simulations in comparison with more traditional regression models. The radioactive fallout from the Chernobyl Nuclear Power Plant accident is used to illustrate the application of the models for prediction and classification problems. This fallout is a unique case study that provides the challenging task of analyzing huge amounts of data ('hard' direct measurements, as well as supplementary information and expert estimates) and solving particular decision-oriented problems.

New microfluidic-based sampling procedure for overcoming the hematocrit problem associated with dried blood spot analysis.

Hematocrit (Hct) is one of the most critical issues associated with the bioanalytical methods used for dried blood spot (DBS) sample analysis. Because Hct determines the viscosity of blood, it may affect the spreading of blood onto the filter paper. Hence, accurate quantitative data can only be obtained if the size of the paper filter extracted contains a fixed blood volume. We describe for the first time a microfluidic-based sampling procedure to enable accurate blood volume collection on commercially available DBS cards. The system allows the collection of a controlled volume of blood (e.g., 5 or 10 μL) within several seconds. Reproducibility of the sampling volume was examined in vivo on capillary blood by quantifying caffeine and paraxanthine on 5 different extracted DBS spots at two different time points and in vitro with a test compound, Mavoglurant, on 10 different spots at two Hct levels. Entire spots were extracted. In addition, the accuracy and precision (n = 3) data for the Mavoglurant quantitation in blood with Hct levels between 26% and 62% were evaluated. The interspot precision data were below 9.0%, which was equivalent to that of a manually spotted volume with a pipet. No Hct effect was observed in the quantitative results obtained for Hct levels from 26% to 62%. These data indicate that our microfluidic-based sampling procedure is accurate and precise and that the analysis of Mavoglurant is not affected by the Hct values. This provides a simple procedure for DBS sampling with a fixed volume of capillary blood, which could eliminate the recurrent Hct issue linked to DBS sample analysis.

Comparative study of the LC-MS/MS and UPLC-MS/MS for the multi-residue analysis of quinolones, penicillins and cephalosporins in cow milk, and validation according to the regulation 2002/657/EC

The aim of this study was to develop and validate an analytical method to simultaneously determine European Union-regulated beta-lactams (penicillins and cephalosporins) and quinolones in cow milk. The procedure involves a new solid phase extraction (SPE) to clean-up and pre-concentrate the three series of antibiotics before analysis by liquid chromatography¿tandem mass spectrometry (LC-MS/MS) and ultra-high-performance liquid chromatography¿tandem mass spectrometry (UPLC-MS/MS). LC-MS/MS and UPLC-MS/MS techniques were also compared. The method was validated according to the Directive 2002/657/EC and subsequently applied to 56 samples of raw cow milk supplied by the Laboratori Interprofessional Lleter de Catalunya (ALLIC) (Laboratori Interprofessional Lleter de Catalunya, Control Laboratory Interprofessional of Milk of Catalunya).

Producció de biopolímers amb cultius bacterians mixtes. Comparació de tres reactors discontinus seqüencials (SBR) amb diferents condicions operacionals

La producció de biopolímers (polihidroxialcanoats (PHA) i substàncies polimèriques extracel·lulars (EPS)) a nivell industrial, resulta una nova àrea d’investigació que recull diverses disciplines, entre elles les Ciències Ambientals. Aquest projecte final de carrera amb el títol: “Producció de biopolímers amb cultius bacterians mixtes”, s’ha desenvolupat sota la supervisió de la directora de projecte Dra. María Eugenia Suárez Ojeda del Departament d’Enginyeria Química de la Universitat Autònoma de Barcelona (UAB) i s’ha dut a terme per l’estudiant Jordi Pérez i Forner de la Llicenciatura de Ciències Ambientals, Facultat de Ciències de la UAB, en el Departament d’Enginyeria Química de la mateixa universitat. L’objectiu d’aquest projecte ha estat produir biopolímers simultàniament amb l’eliminació de fòsfor i matèria orgànica en aigües residuals per obtenir un residu final amb un alt valor afegit. Aquests biopolímers reuneixen les característiques necessàries per a poder competir amb els plàstics convencionals i així, reduir l’elevat consum del petroli i la generació de residus no biodegradables. En aquest projecte s’ha dut a terme la posta en marxa d’un reactor discontinu seqüencial (SBR) per a l’acumulació de biopolímers amb cultius bacterians mixtes. Diferents investigadors han estudiat que aquests tipus de cultius bacterians arriben a nivells de fins el 53-97% [Pijuan et al., 2009] de contingut de biopolímers a la biomassa, sometent als microorganismes a diferents situacions d’estrés ja sigui per dèficit de nutrients o per variacions en les fases de feast-famine (festí-fam). Durant el projecte, s’ha realitzat el monitoratge del reactor alimentat amb una aigua sintètica, elaborada en el laboratori, amb les característiques d’un aigua residual provinent de la industria làctica. S’ha sotmès als microorganismes a diferents condicions operacionals, una d’elles amb limitació de fòsfor com a nutrient i una tercera condició amb una variació a les fases feast-famine. D’altra banda, com a segon objectiu, s’ha analitzat el contingut de biopolímers a la biomassa de dos SBRs més, del grup de recerca Bio-GLS del Departament d’Enginyeria Química de la UAB, alimentats amb diferents fonts de carboni, glicerol i àcids grassos de cadena llarga (AGCLL), per observar les influències que té el tipus de substrat en l’acumulació de biopolímers. Els resultats obtinguts en la primera part d’aquest projecte han estat similars als resultats d’altres investigadors [Pijuan et al., 2009; Guerrero et al., 2012]. S’ha determinat que sotmetre als microorganismes a situacions d’estrés té un efecte directe pel que fa a l’acumulació de biopolímers. També s’ha observat com al mateix temps que acumulaven aquests compostos, els microorganismes desenvolupaven la seva tasca de depurar l’aigua residual, obtenint al final del cicle una aigua amb un baix contingut en matèria orgànica i altres contaminants com amoni i fòsfor, en aquest cas. En la segona part del projecte, s’ha observat com el tipus de substrat té un efecte directe pel que fa a l’acumulació de biopolímers i també a l’activitat metabòlica dels microorganismes. Per tant, s’ha conclòs que la producció de biopolímers mitjançant la depuració d’aigües residuals es una via d’investigació molt prometedora pel que fa als resultats obtinguts. Alhora que es tracta un residu, s’obté una producte residual amb un alt valor afegit que pot ser utilitzat per la producció de bioplàstics 100% biodegradables.

Sublimation of new matrix candidates for high spatial resolution imaging mass spectrometry of lipids: enhanced information in both positive and negative polarities after 1,5-diaminonapthalene deposition.

Matrix sublimation has demonstrated to be a powerful approach for high-resolution matrix-assisted laser desorption ionization (MALDI) imaging of lipids, providing very homogeneous solvent-free deposition. This work presents a comprehensive study aiming to evaluate current and novel matrix candidates for high spatial resolution MALDI imaging mass spectrometry of lipids from tissue section after deposition by sublimation. For this purpose, 12 matrices including 2,5-dihydroxybenzoic acid (DHB), sinapinic acid (SA), α-cyano-4-hydroxycinnamic acid (CHCA), 2,6-dihydroxyacetphenone (DHA), 2',4',6'-trihydroxyacetophenone (THAP), 3-hydroxypicolinic acid (3-HPA), 1,8-bis(dimethylamino)naphthalene (DMAN), 1,8,9-anthracentriol (DIT), 1,5-diaminonapthalene (DAN), p-nitroaniline (NIT), 9-aminoacridine (9-AA), and 2-mercaptobenzothiazole (MBT) were investigated for lipid detection efficiency in both positive and negative ionization modes, matrix interferences, and stability under vacuum. For the most relevant matrices, ion maps of the different lipid species were obtained from tissue sections at high spatial resolution and the detected peaks were characterized by matrix-assisted laser desorption ionization time-of-flight/time-of-flight (MALDI-TOF/TOF) mass spectrometry. First proposed for imaging mass spectrometry (IMS) after sublimation, DAN has demonstrated to be of high efficiency providing rich lipid signatures in both positive and negative polarities with high vacuum stability and sub-20 μm resolution capacity. Ion images from adult mouse brain were generated with a 10 μm scanning resolution. Furthermore, ion images from adult mouse brain and whole-body fish tissue sections were also acquired in both polarity modes from the same tissue section at 100 μm spatial resolution. Sublimation of DAN represents an interesting approach to improve information with respect to currently employed matrices providing a deeper analysis of the lipidome by IMS.

The endocrine disruptor monoethyl-hexyl-phthalate is a selective peroxisome proliferator-activated receptor gamma modulator that promotes adipogenesis.

The ability of pollutants to affect human health is a major concern, justified by the wide demonstration that reproductive functions are altered by endocrine disrupting chemicals. The definition of endocrine disruption is today extended to broader endocrine regulations, and includes activation of metabolic sensors, such as the peroxisome proliferator-activated receptors (PPARs). Toxicology approaches have demonstrated that phthalate plasticizers can directly influence PPAR activity. What is now missing is a detailed molecular understanding of the fundamental basis of endocrine disrupting chemical interference with PPAR signaling. We thus performed structural and functional analyses that demonstrate how monoethyl-hexyl-phthalate (MEHP) directly activates PPARgamma and promotes adipogenesis, albeit to a lower extent than the full agonist rosiglitazone. Importantly, we demonstrate that MEHP induces a selective activation of different PPARgamma target genes. Chromatin immunoprecipitation and fluorescence microscopy in living cells reveal that this selective activity correlates with the recruitment of a specific subset of PPARgamma coregulators that includes Med1 and PGC-1alpha, but not p300 and SRC-1. These results highlight some key mechanisms in metabolic disruption but are also instrumental in the context of selective PPAR modulation, a promising field for new therapeutic development based on PPAR modulation.

Historical reconstruction of polychlorinated biphenyl (PCB) exposures for workers in a capacitor manufacturing plant

We developed a semiquantitative job exposure matrix (JEM) for workers exposed to polychlorinated biphenyls (PCBs) at a capacitor manufacturing plant from 1946 to 1977. In a recently updated mortality study, mortality of prostate and stomach cancer increased with increasing levels of cumulative exposure estimated with this JEM (trend p values = 0.003 and 0.04, respectively). Capacitor manufacturing began with winding bales of foil and paper film, which were placed in a metal capacitor box (pre-assembly), and placed in a vacuum chamber for flood-filling (impregnation) with dielectric fluid (PCBs). Capacitors dripping with PCB residues were then transported to sealing stations where ports were soldered shut before degreasing, leak testing, and painting. Using a systematic approach, all 509 unique jobs identified in the work histories were rated by predetermined process- and plant-specific exposure determinants; then categorized based on the jobs' similarities (combination of exposure determinants) into 35 job exposure categories. The job exposure categories were ranked followed by a qualitative PCB exposure rating (baseline, low, medium, and high) for inhalation and dermal intensity. Category differences in other chemical exposures (solvents, etc.) prevented further combining of categories. The mean of all available PCB concentrations (1975 and 1977) for jobs within each intensity rating was regarded as a representative value for that intensity level. Inhalation (in microgram per cubic milligram) and dermal (unitless) exposures were regarded as equally important. Intensity was frequency adjusted for jobs with continuous or intermittent PCB exposures. Era-modifying factors were applied to the earlier time periods (1946-1974) because exposures were considered to have been greater than in later eras (1975-1977). Such interpolations, extrapolations, and modifying factors may introduce non-differential misclassification; however, we do believe our rigorous method minimized misclassification, as shown by the significant exposure-response trends in the epidemiologic analysis.

High-throughput and sensitive quantitation of plasma catecholamines by ultraperformance liquid chromatography-tandem mass spectrometry using a solid phase microwell extraction plate.

Plasma catecholamines provide a reliable biomarker of sympathetic activity. The low circulating concentrations of catecholamines and analytical interferences require tedious sample preparation and long chromatographic runs to ensure their accurate quantification by HPLC with electrochemical detection. Published or commercially available methods relying on solid phase extraction technology lack sensitivity or require derivatization of catecholamine by hazardous reagents prior to tandem mass spectrometry (MS) analysis. Here, we manufactured a novel 96-well microplate device specifically designed to extract plasma catecholamines prior to their quantification by a new and highly sensitive ultraperformance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method. Processing time, which included sample purification on activated aluminum oxide and elution, is less than 1 h per 96-well microplate. The UPLC-MS/MS analysis run time is 2.0 min per sample. This UPLC-MS/MS method does not require a derivatization step, reduces the turnaround time by 10-fold compared to conventional methods used for routine application, and allows catecholamine quantification in reduced plasma sample volumes (50-250 μL, e.g., from children and mice).

Impact of mycelia on the accessibility of fluorene to PAH-degrading bacteria.

Mycelia have been recently shown to actively transport polycyclic aromatic hydrocarbons (PAH) in water-unsaturated soil over the range of centimeters, thereby efficiently mobilizing hydrophobic PAH beyond their purely diffusive transport in air and water. However, the question if mycelia-based PAH transport has an effect on PAH biodegradation was so far unsolved. To address this, we developed a laboratory model microcosm mimicking air-water interfaces in soil. Chemical analyses demonstrated transport of the PAH fluorene (FLU) by the mycelial oomycete Pythium ultimum that was grown along the air-water interfaces. Furthermore, degradation of mycelia-transported FLU by the bacterium Burkholderia sartisoli RP037-mChe was indicated. Since this organism expresses eGFP in response to a FLU flux to the cell, it was also as a bacterial reporter of FLU bioavailability in the vicinity of mycelia. Confocal laser scanning microscopy (CLSM) and image analyses revealed a significant increase of eGFP expression in the presence of P. ultimum compared to controls without mycelia or FLU. Hence, we could show that physically separated FLU becomes bioavailable to bacteria after transport by mycelia. Experiments with silicon coated glass fibers capturing mycelia-transported FLU guided us to propose a three-step mechanism of passive uptake, active transport and diffusion-driven release. These experiments were also used to evaluate the contributions of these individual steps to the overall mycelial FLU transport rate.

Taking the fungal highway: mobilization of pollutant-degrading bacteria by fungi.

The capacity of fungi to serve as vectors for the dispersion of pollutant-degrading bacteria was analyzed in laboratory model systems mimicking water-saturated (agar surfaces) and unsaturated soil environments (glass-bead-filled columns). Two common soil fungi (Fusarium oxysporum and Rhexocercosporidium sp.) forming hydrophilic and hydrophobic mycelia, respectively, and three polycyclic aromatic hydrocarbon degrading bacteria (Achromobacter sp. SK1, Mycobacterium frederiksbergense LB501TG, and Sphingomonas sp. L138) were selected based on the absence of mutual antagonistic effects. It was shown that fungal hyphae act as vectors for bacterial transport with mobilization strongly depending on the specific microorganisms chosen: The motile strain Achromobacter sp. SK1 was most efficiently spread along hyphae of hydrophilic F. oxysporum in both model systems with transport velocities of up to 1 cm d(-1), whereas no dispersion of the two nonmotile strains was observed in the presence of F. oxysporum. By contrast, none of the bacteria was mobilized along the hydrophobic mycelia of Rhexocercosporidium sp. growing on agar surfaces. In column experiments however, strain SK1 was mobilized by Rhexocercosporidium sp. It is hypothesized that bacteria may move by their intrinsic motilitythrough continuous (physiological) liquid films forming around fungal hyphae. The results of this study suggest that the specific stimulation of indigenous fungi may be a strategy to mobilize pollutant-degrading bacteria leading to their homogenization in polluted soil thereby improving bioremediation.

Propuesta de cursos de capacitación sobre lecciones aprendidas en Costa Rica

El presente proyecto ha sido realizado entre Octubre de 2013 y Febrero de 2014 por un equipo de estudiantes de la licenciatura de Ciencias Ambientales de la Universidad Autónoma de Barcelona. El objeto de estudio es la propuesta de cursos para la formación de tres públicos diferentes, estudiantes, gestores y políticos. Estos cursos se basan en la experiencia de Costa Rica sobre la conservación de la biodiversidad. Costa Rica es un país muy rico en biodiversidad por su clima y sus tierras volcánicas. Una manera de conservar esta gran variedad de especies es protegiendo gran parte del país con reservas y parques nacionales. La metodología utilizada para llevar a cabo estos cursos es la investigación. Recopilar información de las diferentes carencias de distintos países, propuestas pedagógicas para saber mostrar de manera correcta la información a cada público meta y basarlos en el cumplimiento de las Metas Aichi, que tratan de mantener la biodiversidad de manera que contribuya al bienestar de la población. La intención de estos cursos es enseñar a los distintos públicos meta las experiencias positivas que ha tenido Costa Rica para poder desarrollarse tanto en crecimiento económico como de la población conservando su biodiversidad. De manera que en otros países puedan aprender y a la misma vez beneficiarse con las ideas propuestas en los cursos. El curso propuesto para estudiantes trata sobre los servicios ecosistémicos, reconocidos internacionalmente por su empeño en la conservación y uso sostenible de la biodiversidad. El dirigido a gestores, que pueden ser empresarios, es sobre la mejora de la calidad de las aguas, un punto importante para este público que serán los encargados de gestionar este recurso tan importante para mantener en buen estado de conservación la biodiversidad. Finalmente, se propone un curso dirigido a políticos, donde se explica la idea de bioprospección, un tema que se trabaja en el Instituto Nacional de Biodiversidad de Costa Rica y trata de investigar en los organismos que aportan beneficios tanto económicos como en la salud de las personas.