Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Coatings on Composites

Polymer based composite materials coated with thin layers of wear resistant materials have been proposed as replacements for steel components for certain applications with the advantage of reduced mass. Magnetron sputtered coatings can be successfully deposited on composite materials. Nevertheless there are number of issues which must be addressed such as limited temperature, which the composite can withstand because of the epoxy binder which is used, the adhesion of the coating to the composite and the limited mechanical support, the hard coating can obtain from the relatively soft epoxy. We have investigated the deposition of chromium nitride, titanium carbide and titanium doped DLC coatings on carbon fibre reinforced composites and various polymers. The adhesion of the coatings has been studied by the pull-off adhesion tester. In general, the failure mechanism has been noticed to be due to the cohesive failure for a wide range of conditions. The wear behavior of the coatings has been noticed to be complicated. Wear tests on coated composites have shown that where the reinforcing fibres are near the surface, the composite samples do not perform well due to breakage of the fibres from the polymer matrix. A fibre free surface has been noticed to improve the wear resistance.

Entalpia reticular, entalpia de fusão e temperatura de fusão de adutos: algumas correlações empíricas utilizando DSC

By using DSC data is shown that there are empirical correlations between lattice enthalpy, melting enthalpy and the temperature of melting for adducts, and that is possible, using only a single DSC curve, estimate the value of DM Hmq.

Metodologia para o crescimento de esferas monocristalinas de metais nobres

This paper describes in detail a technique employed to grow quasi-spherical single crystals of noble metals for electrochemical applications, using platinum as an example. The metal beads were formed by melting the extremity of a wire in an oxygen / butane flame. X-ray techniques were used to check the crystallization and to determine the orientation of the crystals. Treatment with a pure hydrogen flame followed by a cooling procedure in a hydrogen / argon atmosphere were used for conditioning the well-defined platinum single crystal surfaces. Finally, electrochemical characterization of the Pt(111), Pt(110) and Pt(100) surfaces was done in diluted sulfuric acid solution in the hydrogen adsorption / desorption potential region.

Nitração do fenol, um método em escala semi-micro para disciplina prática de 4 horas

A procedure for the nitration of phenol in a semi-micro scale, followed by separation of the formed orto- and para-nitrophenol isomers by column chromatography, is described. All the experiment, including determination of the melting point of the isolated products, require a period of 4 hours, and it is suitable for organic chemistry laboratory undergraduate courses.

Determinacion de la configuracion E-Z de los acidos Fumarico y Maleico. Un experimento orientado a incentivar el desarrollo de la investigacion cientifica en alumnos de Pregrado

In this work we intend to eliminate the idea that laboratory exercises seem like cookbooks. That is, exercises shall be presented as a problematic situation. Based on observation and experimentation, the students should determine the E-Z configuration of maleic and fumaric acids. The basis of this laboratory exercise is the acid-catalyzed isomerization of maleic acid to fumaric acid. Students are given the starting material, reagents and the experimental procedure. They are told that the starting material is a dicarboxylic acid containing a C=C double bond of formula C4H4O4. Students determine melting points, solubilities, acidity and chromatographic patterns for both the starting material and the product, so that a configuration of each acid can be proposed. This type of experiment yields excellent results, because the students are left to deduce that maleic acid is less stable than fumaric acid. Additionally, they conclude that maleic acid is the "Z" isomer and fumaric acid is the "E" isomer. Finally, this laboratory exercise allows the students to develop simultaneously their critical-thinking skills with the respective laboratory techniques and not to see chemistry as recipes to be followed.

Determinação da massa molar por crioscopia: terc-butanol, um solvente extremamente adequado

We intend to divulge an easy experiment that permits the determination of molar masses of various compounds by cryoscopy. The major advantage of this is the use of the tert-butyl alcohol as a solvent, which requires simple apparatus and easy procedures. The melting point of this alcohol is around 25 ºC, which makes it easy to freeze and then melt the solutions. This solvent has a high cryoscopic constant and is miscible with both polar and non-polar compounds. The molar masses of acetone, water, chloroform, dichloro-methane, ethanol, hexane, carbon tetrachloride and toluene were determined. The results were good except for water. Even though there are reliable techniques of molar mass determination nowadays, this method is still frequently taught in undergraduate courses.

Desenvolvimento de um dispositivo para obtenção de monocristais de ligas à base de cobre

This paper describes the drawing, construction and optimization of a device, which can be used to obtain single crystals of different metallic materials with melting point from 550 to 1050 ºC. Components of ease obtaining and of low cost were used. The device was based on the modified Bridgman technique and it was used to obtain single crystals of copper-based alloys. The temperature axial profiles and a difference less then 1% in the temperature between the wall and the center of the ceramic tube in the critical region for obtaining single crystals of good quality indicated that the oven presents a good thermal stability. Single crystals of CuZnAl and CuAlAg alloys of good quality were growth and characterized using optical microscopy and Laüe X-ray back reflection.

Lanthanide Chelates as Donors in Fluorescence Resonance Energy Transfer: Exciting Prospects for Bioaffinity Assay Detection

Fluorescence resonance energy transfer (FRET) is a non-radiative energy transfer from a fluorescent donor molecule to an appropriate acceptor molecule and a commonly used technique to develop homogeneous assays. If the emission spectrum of the donor overlaps with the excitation spectrum of the acceptor, FRET might occur. As a consequence, the emission of the donor is decreased and the emission of the acceptor (if fluorescent) increased. Furthermore, the distance between the donor and the acceptor needs to be short enough, commonly 10-100 Å. Typically, the close proximity between the donor and the acceptor is achieved via bioaffinity interactions e.g. antibody binding antigen. Large variety of donors and acceptors exist. The selection of the donor/acceptor pair should be done not only based on the requirements of FRET but also the performance expectancies and the objectives of the application should be considered. In this study, the exceptional fluorescence properties of the lanthanide chelates were employed to develop two novel homogeneous immunoassays: a non-competitive hapten (estradiol) assay based on a single binder and a dual-parametric total and free PSA assay. In addition, the quenching efficiencies and energy transfer properties of various donor/acceptor pairs were studied. The applied donors were either europium(III) or terbium(III) chelates; whereas several organic dyes (both fluorescent and quenchers) acted as acceptors. First, it was shown that if the interaction between the donor/acceptor complexes is of high quality (e.g. biotin-streptavidin) the fluorescence of the europium(III) chelate could be quenched rather efficiently. Furthermore, the quenching based homogeneous non-competitive assay for estradiol had significantly better sensitivity (~67 times) than a corresponding homogeneous competitive assay using the same assay components. Second, if the acceptors were chosen to emit at the emission minima of the terbium(III) chelate, several acceptor emissions could be measured simultaneously without significant cross-talk from other acceptors. Based on these results, the appropriate acceptors were chosen for the dual-parameter assay. The developed homogeneous dual-parameter assay was able to measure both total and free PSA simultaneously using a simple mix and measure protocol. Correlation of this assay to a heterogeneous single parameter assay was excellent (above 0.99 for both) when spiked human plasma samples were used. However, due to the interference of the sample material, the obtained concentrations were slightly lower with the homogeneous than the heterogeneous assay, especially for the free PSA. To conclude, in this work two novel immunoassay principles were developed, which both are adaptable to other analytes. However, the hapten assay requires a rather good antibody with low dissociation rate and high affinity; whereas the dual-parameter assay principle is applicable whenever two immunometric complexes can form simultaneously, provided that the requirements of FRET are fulfilled.

Hajupäästöjen tutkiminen Saint-Gobain Rakennustuotteet Oy:n Hyvinkään lasivillatehtaalla

Hajupäästöillä tarkoitetaan tavallisesti teollisen toiminnan aiheuttamia hajuaineiden päästöjä ympäristöön. Suomessa ympäristölainsäädäntö ei varsinaisesti kiellä hajuaineiden päästöjä mutta edellyttää kuitenkin, ettei niistä aiheudu merkittävää viihtyvyyshaittaa. Tässä työssä tutkittiin hajupäästöjä Saint-Gobain Rakennustuotteet Oy:n Hyvinkään lasivillatehtaalla. Tavoitteena työssä oli selvittää, mikä on tehtaan aiheuttamien päästöjen hajuvaikutus, ja mitä hajuyhdisteitä valmistusprosessissa muodostuu. Lisäksi työssä selvitettiin miten hajupäästöjä pystyttäisiin vähentämään. Työn kokeellisten tutkimusten aikana kerättiin tietoa hajun esiintymisestä valitulta tarkasteluajanjaksolta sekä mitattiin mm. tehtaan savukaasujen hajupitoisuutta ja koostumusta. Mittauksissa kaasunäytteiden hajupitoisuudeksi saatiin 170 HY/m3, joka kuvaa suhteellisen mietoa hajua. Näytteistä analysoidut haihtuvat orgaaniset yhdisteet olivat suurelta osin peräisin lasivillan valmistuksessa käytetystä sideaineesta, jota lisätään tuotteen joukkoon kuidutusvaiheessa. Ympäristöstä otetuista näytteistä ei kuitenkaan havaittu piipun yhdisteitä, mikä viittaisi siihen, että mittausjaksonaikana tehtaan päästöjen leviäminen ympäristöön on tapahtunut melko pieninä pitoisuuksina. Lisäksi on mahdollista, että ulkoilmassa yhdisteissä tapahtuu kemiallista muutuntaa ja hajontaa, jonka seurauksena yhdisteet muuttuvat. Tehtaan hajuhaitat vaikuttaisivat tutkimustulosten mukaan johtuvan savupainumaksi kutsutusta ilmiöstä. Savupainumaan vaikuttavat kaasun lämpömäärä sekä ympäristön olosuhteet ja topografia. Hajuhaittojen poistamiseksi olisi muodostuvia hajuyhdisteitä pystyttävä vähentämään 95-100 %.

Welding of Sheet metal using Modified short arc MIG/MAG welding process

In this research work, the results of an investigation dealing with welding of sheet metals with diverse air gap using FastROOT modified short arc welding method and short circuit MAG welding processes have been presented. Welding runs were made under different conditions and, during each run, the different process parameters were continuously monitored. It was found that maximum welding speed and less HAZ are reached under specific welding conditions with FastROOT method with the emphasis on arc stability. Welding results show that modified short arc exhibits a higher electrode melting coefficient and with virtually spatter free droplet transition. By adjusting the short circuit duration the penetration can be controlled with only a small change in electrode deposition. Furthermore, by mixing pulsed MIG welding with modified arc welding the working envelope of the process is greatly extended allowing thicker material sections to be welded with improved weld bead aesthetics. FastROOT is a modified short arc welding process using mechanized or automated welding process based on dip transfer welding, characterized by controlled material deposition during the short circuit of the wire electrode to the workpiece.

Rederibarometern. Juli 2009

Shortsea Promotion Centre (SPC) Finland som främjar närsjofart publicerar den sjätte rederibarometern i samarbete med den finländska rederinäringen. Utöver hela den finländska rederinäringen finns även de andra transportformerna och parterna i transportkedjan från både den privata och offentliga sektorn representerade i SPC Finland. SPC Finland hör till Sjöfartbranschens utbildnings- och forskningscentral vid Åbo universitet och fungerar i centralens enhet i Björneborg. SPC Finlands verksamhet omfattar utöver närsjöfartsfrämjandet intermodala transporter som binder ihop järn-vägs-, landvägs- och insjötransporter med närsjöfarten. Barometern producerar information om sjöfartens verksamhetsområde för rederibranschen, dess intressentgrupper och de politiska beslutsfattarna. Barometern är framför allt avsedd som ett arbetsredskap för dem som arbetar med sjötransporter. Barometern utvecklades på våren 2006. Då gjordes förfrågan för första gången men den publicerades inte. För att konkretisera nyttan av barometern upprepas den regelbundet med ett halvårs mellanrum. Långa tidsserier möjliggör en mångsidig analysering av resultaten. Nästa förfråga genomförs i november 2009. Resultaten av föreliggande barometer skall publiceras den 17 juli 2009 i samband med Suomi Areena -evenemanget i Björneborg. SPC Finland riktar ett tack till alla rederier som deltagit i förfrågan och hoppas på respons för att kunna vidareutveckla barometern. Mer information om barometern fås av forskaren Pekka Sundberg, tfn. (02) 333 8104 eller e-post pekka.sundberg@shortsea.fi.

Laüe back-reflection method for crystallographic orientation of a martensitic Cu-Zn-Al single crystal of the monoclinic system

A martensitic single crystal Cu-23.95Zn-3.62(wt.%)Al alloy was obtained melting pure Cu, Zn and Al using Bridgman's method. The martensitic phase (monoclinic) can present up to 24 variants, and orienting the surface according to a certain plane is a very hard task. The single crystal was submitted to 8 tons of tension (stress) along the longitudinal direction to reduce the number of variants and facilitate the surface orientation according to the desired plane. This single crystal was oriented using the Laüe back-reflection method to give surfaces with the following oriented crystallographic planes: (010), (120) and (130). It was observed that the tension stress was applied along the [010] direction.

Lipídios estruturados obtidos a partir da mistura de gordura de frango, sua estearina e triacilgliceróis de cadeia média: II- pontos de amolecimento e fusão

The aim of the present work is to investigate the effects of blending and chemical interesterification reactions on the softening and melting behavior of chicken fat, its stearin and medium chain triacylglycerols, and blends thereof in various ratios. Chemical interesterification is a promising alternative to the current processes of modifying the physical properties of fats. In the experimental design 7 samples corresponding to 7 different blend proportions were used. The results were represented in triangular diagrams. The addition of stearin influenced the softening and melting points. The mixture response surface methodology proved to be an extremely useful tool for the optimization of the fat mixtures.

Métodos simples de formação de monocristal de substância orgânica para estudo estrutural por difração de raios X

This work presents three operationally simple laboratory protocols for monocrystal growth of small-molecule organic compounds, which have been applied with success in the last ten years for the formation of single crystals for X-ray structural studies. In addition, five structure hints were formulated as general guidelines for selecting a small-molecule organic compound as a candidate for monocrystal growth: molecular weight >200 D, melting point >100 ºC, two or more aromatic rings in the structure, at least two sites for intermolecular hydrogen bond formation, and a halogen or other heavy atom in the structure.