Slurry flow in mills: grate-only discharge mechanism (Part-1)

Discharge grates play an important role in determining the performance of autogenous, semi-autogenous and grate discharge ball mills. The flow capacity (grinding capacity) of these mills is strongly influenced by the discharge grate design-open area and position of apertures, as well as the performance of the pulp lifters. As mill sizes have progressively increased and closed-circuiting has become more popular the importance of grate and pulp lifter design has grown. Unfortunately very few studies have concentrated on this aspect of mill performance. To remedy this a series of laboratory and pilot-scale tests were undertaken to study both the performance of grates on their own and in conjunction with pulp lifters. In this first paper of a two-part series the results from the grate-only experiments are presented and discussed, whilst the performance of the grate-pulp-lifter system is covered in the second paper. The results from the grate-only experiments have shown that the build-up of slurry (hold-up) inside the mill starts from the shoulder of the charge, while the toe position of the slurry progressively moves towards the toe of the charge with increasing flowrate. Besides grate design (open area and position of apertures), charge volume and mill speed were also found to have a strong influence on mill hold-up and interact with grate design variables. (C) 2003 Elsevier Science Ltd. All rights reserved.

Discrete element modelling of power draw of tumbling mills

The power required to operate large mills is typically 5-10 MW. Hence, optimisation of power consumption will have a significant impact on overall economic performance and environmental impact. Power draw modelling results using the discrete element code PFC3D have been compared with results derived from the widely used empirical Model of Morrell. This is achieved by calculating the power draw for a range of operating conditions for constant mill size and fill factor using two modelling approaches. fThe discrete element modelling results show that, apart from density, selection of the appropriate material damping ratio is critical for the accuracy of modelling of the mill power draw. The relative insensitivity of the power draw to the material stiffness allows selection of moderate stiffness values, which result in acceptable computation time. The results obtained confirm that modelling of the power draw for a vertical slice of the mill, of thickness 20% of the mill length, is a reliable substitute for modelling the full mill. The power draw predictions from PFC3D show good agreement with those obtained using the empirical model. Due to its inherent flexibility, power draw modelling using PFC3D appears to be a viable and attractive alternative to empirical models where necessary code and computer power are available.

Comparison of DEM and experiment for a scale model SAG mill

Predictions of flow patterns in a 600-mm scale model SAG mill made using four classes of discrete element method (DEM) models are compared to experimental photographs. The accuracy of the various models is assessed using quantitative data on shoulder, toe and vortex center positions taken from ensembles of both experimental and simulation results. These detailed comparisons reveal the strengths and weaknesses of the various models for simulating mills and allow the effect of different modelling assumptions to be quantitatively evaluated. In particular, very close agreement is demonstrated between the full 3D model (including the end wall effects) and the experiments. It is also demonstrated that the traditional two-dimensional circular particle DEM model under-predicts the shoulder, toe and vortex center positions and the power draw by around 10 degrees. The effect of particle shape and the dimensionality of the model are also assessed, with particle shape predominantly affecting the shoulder position while the dimensionality of the model affects mainly the toe position. Crown Copyright (C) 2003 Published by Elsevier Science B.V. All rights reserved.

Trichostome ciliates from Australian marsupials. II. Polycosta gen. nov (Litostomatea : Polycostidae fam. nov.)

A new family, Polycostidae, containing one new genus, Polycosta, of ciliates endwocommensal in the stomachs of macropodid marsupials is described. Four new species, A roundi, P. turniae, A sebastopolensis and P. parma are described from Wallabia bicolor, Macropus dorsalis, Petrogale herberti and M. eugenii, respectively. Polycosta is holotrichous with slightly spiral meridional kineties arranged between broad interkinetal ridges. The ultrastructure of one representative species displays the knitted together pattern of postciliary microtubules and kinetodesmata of somatic kinetids common in trichostomes and the interkinetal ridges are dominated by layers of dark bodies but lack ectoplasmic hydrogenosomes. The vestibulum is conical and its aperture appears capable of closing tightly in most species; vesibular kineties are continuations of the right somatic kineties into the vestibulum. There is a prominent phago-plasm delimited internally by a basket of nematodesmata derived from electron dense plates at the bases of kinetosomes the anterior somatic and vestibular kineties. There is a prominent cytoproct which is situated within an invagination of the cell in some species. Polycosta is similar to Amylovorax in terms of gross morphology, somatic ciliature and cortical ultrastructure. The vestibular ultrastructure, however, is more similar to that of Macropodinium. The affinities of the group are thus not clear and this unique combination of characters supports the erection of a new family.

Do expertise and the degree of perception-action coupling affect natural anticipatory performance?

Two experiments using a temporal occlusion paradigm (the first with expert and novice participants and the second with participants of intermediate skill) were conducted to examine the capability of tennis players to predict the direction of an opponent's service in situ. In both experiments two different response conditions, reflecting differing degrees of perception-action coupling, were employed. In a coupled condition players were required to make a movement-based response identical to that which they would use to hit a return of service in a game situation, whereas in an uncoupled condition a verbal prediction of service direction was required. Experiment 1 provided clear evidence of superior prediction accuracy under the coupled response condition when ball flight was available, plus some limited evidence to suggest that superior prediction accuracy under uncoupled response conditions might hold true if only advance (pre-contact) information was available. Experiment 2 showed the former finding to be a robust one, but was unable to reveal any support for the latter. Experiment 1 also revealed that expert superiority is more apparent for predictions made under natural (coupled) than uncoupled response-mode conditions. Collectively, these findings suggest that different perceptual processes may be in operation in anticipatory tasks which depend on skill level, the type of information presented, and degree of perception-action coupling inherent in the task requirements.

Effects of speaking rate on EMA-derived lingual kinematics: a preliminary investigation

Electromagnetic articulography (EMA) was used to investigate how tongue movement characteristics (i.e., velocity, acceleration, duration, distance) change with. or indeed affect, increased rates of speech. Eight young adult males repeated /ta/ and /ka/ syllables first at a moderate rate that had been modelled at three syllables per second, and then 'as fast as possible'. Distance travelled by the tongue appeared to be the principal lingual kinematic feature manipulated by the group of speakers in producing increased syllable repetition rates, with velocity found to increase, decrease or remain unchanged. Acceleration remained unchanged, except in the case of increased velocity. One participant formed an exception in terms of manipulating distance by exhibiting marginally increased lingual velocities rather than distance changes. This preliminary study serves to direct future EMA-based studies of speech rate control as to the speech tasks that should be employed and the possible underlying anatomical and acoustic bases or constraints that could possibly influence the kinematic strategies employed to increase speech rate.

Parvalbumin-, calbindin-, and calretinin-immunoreactive neurons in the prefrontal cortex of the owl monkey (Aotus trivirgatus): A standardized quantitative comparison with sensory and motor areas

Recent studies have revealed regional variation in the density and distribution of inhibitory neurons in different cortical areas, which are thought to reflect area-specific specializations in cortical circuitry. However, there are as yet few standardized quantitative data regarding how the inhibitory circuitry in prefrontal cortex (PFC), which is thought to be involved in executive functions such as cognition, emotion and decision making, compares to that in other cortical areas. Here we used immunohistochemical techniques to determine the density and distribution of parvalbumin (PV)-, calbindin (CB)-, and calretinin (CR)-immunoreactive (ir) neurons and axon terminals in the dorsolateral and orbital PFC of the owl monkey (Aotus trivirgatus), and compared them directly with data obtained using the same techniques in 11 different visual, somatosensory and motor areas. We found marked differences in the density of PV-ir, CB-ir, and CR-ir interneurons in several cortical areas. One hundred and twenty eight of all 234 possible between-area pairwise comparisons were significantly different. The density of specific subpopulations of these cells also varied among cortical areas, as did the density of axon terminals. Comparison of PFC with other cortical areas revealed that 40 of all 66 possible statistical comparisons of the density of PV-ir, CB-ir, and CR-ir cells were significantly different. We also found evidence for heterogeneity in the pattern of labeling of PV-ir, CB-ir, and CR-ir cells and axon terminals between the dorsolateral and orbital subdivisions of PFC. These data are likely to reflect basic differences in interneuron circuitry, which are likely to influence inhibitory function in the cortex. Copyright (C) 2003 S. Karger AG, Basel.

Teoria da estrutura em organiza????o

Dentro de uma conceitua????o geral, pode-se dizer que organiza????o ?? sinergia: unidade de a????o. E que a unidade de a????o tem seu fundamento na singularidade de prop??sito. Assim, um team de foot-ball, que ?? um conjunto de elementos operando com o mesmo prop??sito, ?? uma organiza????o. Esta caracteriza????o din??mica subentende a exist??ncia de uma base f??sica em cada organiza????o. A base f??sica, ou o corpo da organiza????o, ?? o grupo social. A ci??ncia organiza????o se preocupa com os fen??menos da natureza relacional, ocorridos entre os elementos do grupo social , e que repercutem na consecu????o do fim a que se prop??e o grupo. P??sto assim o problema, percebe-se, de imediato, que em organiza????o todos os fatos s??o moldados por um valor constante: o fim a que se prop??e o grupo; e que a natureza d??sses fatos ?? ???relacional???, do que resulta serem insepar??veis, inatomiz??veis. Uma an??lise, mesmo superficial de um grupo organizado ??? voltemos ao exemplo do team de foot-ball ??? revela que ??le ?? constitu??do de: a) elementos materiais e humanos (a bola, o campo e os homens); b) tarefas a executar (as fun????es de keeper, de back, etc); c) rela????es estruturais f??sicas e psicol??gicas entre os elementos para realiza????o das tarefas.

Efeito da distribuição do tamanho das partículas abrasivas sobre as taxas e modos de desgaste para o ensaio de microabrasão

Neste trabalho, as distribuições de tamanhos das partículas de dois pós de Carboneto de Silício foram previamente avaliadas e os resultados indicaram uma distribuição Gaussiana para ambos, com tamanhos médios na ordem de 2 μm para o primeiro e 6 μm para o segundo. Posteriormente foram misturados os dois pós originais com diferentes frações mássicas, proporcionando uma nova série de pós de Carboneto de Silício (SiC), que seriam usados nos ensaios de microabrasão com configuração de esfera fixa. A caracterização desta nova série de pós mostrou larguras maiores para aqueles com alto porcentagem do abrasivo pequeno (2,11 μm), conservando a aparência Gaussiana dos originais. Por outro lado para os pós com uma quantidade maior do abrasivo grande (6,57 μm), foram obtidas curvas com uma leve tendência bimodal, mas também apresentaram maiores larguras. As provas foram conduzidas sobre aço carbono AISI 1020, para duas condições diferentes de carga normal e os resultados foram analisados em termos da taxa de desgaste, bem como dos micromecanismos de desgaste (abrasão por rolamento ou abrasão por riscamento). Os resultados indicaram que a fração mássica dos pós originais tem um efeito significante sobre os micromecanismos de desgaste observados e que as taxas de desgaste não segue uma relação linear com a fração mássica do pó com maior tamanho da partícula abrasiva. Além disso, a análise da severidade de contato determinou que esta diminui durante os ensaios conduzidos com carga constante. Este fenômeno está associado ao aumento da área da cratera de desgaste que produz uma diminuição da pressão de contato. Assim, um incremento para o número de eventos associado ao rolamento de partículas seria esperado, favorecendo a observação de múltiplas indentações ao longo dos sulcos formados previamente. Isto foi confirmado por meio de micrografias eletrônicas de varredura das amostras após ensaios de microabrasão.