Montagem de um sistema para medidas galvanostáticas simultâneas em mais de uma célula

The present work deals with the design and construction of an equipment for muti-cell accelerated stability test measurements (AST) of dimensionally stable anodes (DSA). The equipment was built using only components that were available in the laboratory. Measurements of three electrochemical cells can be performed using the developed software. The acquisition time interval and the cut-off potencial can be set by the user. Experimental data for RuO2 electrodes obtained with the built equipment are in agreement with the literature.

Propriedades reológicas e efeito da adição de sal na viscosidade de exopolissacarídeos produzidos por bactérias do gênero Rhizobium

Viscosity of some polysaccharide solutions supports that these molecules can be applied in food sectors. Four exopolysaccharides (R1, R2, R3, R4) produced by different Rhizobium strains were selected. Sugar composition and differences in the uronic acid contents suggests that chemical structure of these molecules can vary when different culture conditions and strains are analyzed. The Power Law was the rheological model used to represent the experimental data of shear stress versus shear rate. All exopolysaccharides showed non-Newtonian behavior, with pseudoplastic characteristics. R1, R2 and R4 showed a slight increase in viscosity in the presence of 0,2 M NaCl.

Determinação espectrofotométrica de cloreto em cimento após preparo de amostra por piroidrólise

A method based on pyrohydrolysis was proposed for cement sample preparation and further chloride determination by spectrophotometry using flow injection analysis. Analytical parameters were evaluated and, under the selected conditions, the calibration curve was linear in the range of 0.2 to 10.0 µg mL-1 with r2 = 0.998. The limit of detection was5 µg g-1 of chloride and the relative standard deviation was less than 7%. The proposed pyrohydrolysis method is relatively simple and can be used for sample preparation for further spectrophotometric determination of low concentrations of chloride in cement.

MONITORING OF ORGANOPHOSPHOROUS PESTICIDE RESDUES IN SAMPLES OF BANANA, PAPAYA, AND BELL PEPPER

The objective of this study was to monitor 11 organophosphorus pesticides in samples of papaya, bell pepper, and banana, commercialized in the metropolitan area of Vitória (ES, Brazil). The pesticides were determined by an optimized and validated method using high performance liquid chromatography with tandem mass spectrometry (HPLC-MS/MS). All three samples exhibited a matrix effect for most of the pesticides, mainly with signal suppression, and therefore the calibration curves were produced in matrices. Linearity revealed coefficients of determination (r2) greater than 0.9895 for all pesticides and recovery results ranged from between 76% and 118% with standard deviation no greater than 16%. Precision showed relative standard deviation values lower than 19% and HorRat values lower than 0.7, considering all pesticides. Limits of quantification were less than 0.01 mg/kg for all pesticides. Regarding analysis of the samples (50 of each), none of the pesticides exceeded the maximum residue limit determined by Brazilian legislation.

PRELIMINARILY DEVELOPMENT OF A MOISTURE-ACTIVATED BIORESORBABLE POLYMERIC PLATFORM FOR DRUG DELIVERY

Bioresorbable polymeric films were prepared by solvent casting using a tyrosine-derived polycarbonate and metronidazole (MDZ) as the model drug at 2.5%, 5% and 10% (w/w). Drug loading did not affect the water uptake, drug release, polymer degradation or erosion profiles. All devices released approximately 85% (w/w) of the drug within a 1.5 h period. This may be attributed to the rapid water uptake of the polymer. An increase in the water uptake correlated with a linear rate increase of the polymer degradation (0.968 ≤ R2 ≤ 0.999). Moreover, MDZ presented a remarkable plasticizing effect for the polymer and drug loading exerted a significant impact on the mechanical properties of the obtained films. The results obtained can be used to further the development of novel biocompatible and biodegradable polymeric platforms for the delivery of metronidazole and other drugs in a broad range of pharmaceutical applications.

CHARACTERIZING THE MECHANISM OF QUETIAPINE DISTRIBUTION IN LIPID-CORE NANOCAPSULES PSEUDO-PHASES USING A VALIDATED LC/UV METHOD

Quetiapine is an atypical antipsychotic used to treat schizophrenia. However, despite great interest for its chronic therapeutic use, quetiapine has some important side effects such as weight gain induction. The development of a quetiapine nanocarrier can potentially target the drug into central nervous system, resulting in a reduction of systemic side effects and improved patient treatment. In the present work, a simple liquid chromatography/ultraviolet detection (LC/UV) analytical method was developed and validated for quantification of total quetiapine content in lipid core nanocapsules as well as for determination of incorporation efficiency. An algorithm proposed by Oliveira et al. (2012) was applied to characterize the distribution of quetiapine in the pseudo-phases of the nanocarrier, leading to a better understanding of the quetiapine nanoparticles produced. The analytical methodology developed was specific, linear in the range of 0.5 to 100 µg mL−1 (r2 > 0,99), and accurate and precise (R.S.D < ±5%). The absolute recovery of quetiapine from the nanoparticles was approximately 98% with an incorporation efficiency of approximately 96%. The results indicated that quetiapine was present in a type III distribution according to the algorithm, and was mainly located in the core of the nanoparticle because of its logD in the formulation pH (6.86 ± 0.4).

MCR-ALS APLICADO NO MONITORAMENTO QUANTITATIVO DO PROCESSO DE ELETRODEGRADAÇÃO DA ATRAZINA USANDO ESPECTROS UV: RESULTADOS COMPARATIVOS COM HPLC-DAD COMO UM MÉTODO DE REFERÊNCIA

Electrodegradation of atrazine in water was performed using homemade (PA and PB) and purchased (PC) boron-doped diamond anodes. The degradation was monitored off-line by analyzing total organic carbon and high performance liquid chromatography with diode array detector (HPLC-DAD) and at-line by UV spectroscopy. The spectra were recorded every 2 min. The rank deficiency problem was resolved by assembling an augmented column-wise matrix. HPLC was employed to separate the original and byproducts degradation components. Aiming the same goal, multivariate curve resolution - alternating least squares (MCR-ALS) was applied to resolve the UV spectroscopic data. Comparison between HPLC and MCR-ALS separations is presented. By using MCR-ALS the spectra of atrazine and two byproducts were successfully resolved and the resulted concentration profiles properly represented the system studied. The ALS explained variance (R2) for PA, PB and PC was equal to 99.99% for all of them and the lack of fit for PA, PB and PC were 0.39, 0.34 and 0.54 respectively. The correlation (R) between the recovered and pure spectra were calculate for each electrodegradation, validating the MCR-ALS results. The average R was equal to 0.997. The spectral and concentration profiles described with this new approach are in agreement with HPLC-DAD results. The proposed method is an alternative to classical analyses for monitoring of the degradation process, mainly due to the simplicity, fast results and economy.

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Development of virus resistant transgenic papayas expressing the coat protein gene from a Brazilian isolate of Papaya ringspot virus

Translatable and nontranslatable versions of the coat protein (cp) gene of a Papaya ringspot virus (PRSV) isolate collected in the state of Bahia, Brazil, were engineered for expression in Sunrise and Sunset Solo varieties of papaya (Carica papaya). The biolistic system was used to transform secondary somatic embryo cultures derived from immature zygotic embryos. Fifty-four transgenic lines, 26 translatable and 28 nontranslatable gene versions, were regenerated, with a transformation efficiency of 2.7%. Inoculation of cloned R0 plants with PRSV BR, PRSV HA or PRSV TH, Brazilian, Hawaiian and Thai isolates, respectively, revealed lines with mono-, double-, and triple-resistance. After molecular analysis and a preliminary agronomic evaluation, 13 R1 and R2 populations were incorporated into the papaya-breeding program at Embrapa Cassava and Tropical Fruits, in Cruz das Almas, Bahia, Brazil.

Proliferação de ramos em plantas comerciais de bico-de-papagaio associada a fitoplasma do grupo 16srIII

Bico-de-papagaio é uma espécie ornamental, encontrada tanto na forma de arbustos, presente em jardins residenciais e públicos, como comercializada em vasos para decoração de interiores. Com o objetivo de detectar a presença de fitoplasma em plantas mostrando sintomas de proliferação de ramos, amostras foram obtidas de plantas sintomáticas e assintomáticas cultivadas em jardins e de plantas comerciais sintomáticas envasadas. A técnica de duplo PCR, utilizando os iniciadores R16mF2/mR1 e R16F2n/R2, foi empregada para detecção do fitoplasma, a partir de DNA extraído de folhas. Fitoplasma foi detectado consistentemente em todas as amostras sintomáticas, porém não houve detecção em qualquer das amostras assintomáticas. A identificação molecular conduzida através de PCR com iniciadores específicos e por análise de RFLP revelou que o fitoplasma detectado pertence ao grupo 16SrIII. Assim, foi demonstrado que a ocorrência de proliferação de ramos em bico-de-papagaio está associada à presença de fitoplasma. Plantas superbrotadas apresentam um dossel mais compacto, sendo mais atrativas ao consumidor, portanto a presença do fitoplasma é considerada como benéfica para fins ornamentais e comerciais.

Relações lineares múltiplas entre deslocamentos químicos em RMN 13C de haletos alifáticos

Os deslocamentos químicos de RMN 13C de carbonos a , b , g e d de 17 conjuntos de haletos (F, Cl Br e I) alifáticos, inclusive compostos mono, bi e tricíclicos, podem ser reproduzidos por uma equação linear de duas constantes e duas variáveis do tipo : d R-X = A*d R-X1 + B*d R-X2 onde A e B são constantes obtidas por regressão multilinear a partir de deslocamentos químicos de 13C; d R-X, o deslocamento químico de 13C do composto com halogênio (R-X); d R-X1 e d R-X2 deslocamentos químicos de outros haletos. Para brometos (R-X) alifáticos a melhor correlação foi obtida com os dados de fluoretos (R-X1) e iodetos (R-X2) com R2 de 0,9989 e desvio médio absoluto (DM) de 0,39ppm. Para cloretos (R-X) a melhor correlação foi com dados de brometos (R-X1) e iodetos (R-X2) com R2 de 0,9960 e DM de 0,76ppm. Para fluoretos (R-X) a melhor correlação foi com brometos (R-X1) e iodetos (R-X2) com R2 de 0,9977 e DM de 1,10ppm e para iodetos (R-X) foi com fluoretos (R-X1) e brometos (R-X2) com R2 de 0,9972 e desvio médio absoluto de 0,60 ppm.

Potencialidades analíticas do dietilditiofosfato de amônio em espectrometria de massas com plasma indutivamente acoplado empregando extração em fase sólida e sistemas de injeção em fluxo

Um sistema de injeção em fluxo envolvendo complexação com dietilditiofosfato de amônio e sorção de complexos metálicos em minicolunas de sílica gel modificada por grupos octadecil C18 é proposto para determinações multielementares em espectrometria de massa com plasma indutivamente acoplado. Influência da concentração de reagentes, natureza do ácido, tempo de reação, tempos de comutação, vazões e interferência de sódio foram investigadas. Água ou solução 2% v/v HNO3 podem ser utilizadas para lavar a coluna antes da eluição dos analitos com etanol. Amostras contendo 5000 mg Na L-1 e analisadas diretamente com o sistema proposto produzem uma concentração aparente de 63Cu de 0,45 µg L-1; por outro lado não foi observada interferência para As, Pb, Bi, Se, In, Tl, Cd, Hg e 65Cu. Para 0,25 % w/v NH4DTP e 3 mL de solução de amostra, curvas analíticas para Bi, Cu, Pb, As, Se, In, Tl, Cd, Hg no intervalo de 0,10 a 2,00 µg L-1 podem ser construídas com boas correlações (r2 > 0.998). A velocidade analítica e sensibilidade podem ser melhoradas pois dependem das condições de pré-concentração e eluição selecionadas. Com os parâmetros acima fixados, limites de detecção de 0.014 (Cu), 0.027 (As), 0.06 (Se), 0.02 (Cd), 0.029 (In), 0.043 (Hg), 0.02 (Tl), 0.06 (Pb) e 0.002 µg L-1 (Bi) foram obtidos.

Evidência molecular da ocorrência de um fitoplasma associado ao lenho mole da macieira

O lenho mole da macieira é uma doença relevante em diversas partes do mundo. Sintomas típicos desta doença têm sido observados em pomares instalados em estados do sul do território brasileiro desde a década de oitenta. Enxertia tem revelado a natureza infecciosa da doença e a observação de corpúsculos filamentosos no floema tem evidenciado possível associação com fitoplasma. No presente trabalho plantas com sintomas de lenho mole foram coletadas em pomar comercial, visando demonstrar a presença de fitoplasma em tecido doente, bem como identificar molecularmente este fitoplasma. Através do emprego de duplo PCR com iniciadores universais R16mF2/R1 e R16F2n/R2, fitoplasma foi consistentemente detectado em plantas sintomáticas. A identificação conduzida com duplo PCR usando-se iniciadores específicos R16(III)F2/R demonstrou que o fitoplasma detectado pertencia ao grupo 16SrIII. Análises de RFLP conduzidas com as endonucleases AluI, KpnI, HinfI, HpaII, MseI, RsaI e SauIIIA confirmaram que o fitoplasma era um representante típico do grupo 16SrIII. A detecção e identificação molecular se constitui numa forte evidência que um fitoplasma está associado ao lenho mole da macieira no Brasil, complementando os trabalhos realizados anteriormente com transmissão por enxertia e observação por microscopia eletrônica .

On convergence of transforms based on parabolic scaling

This thesis studies properties of transforms based on parabolic scaling, like Curvelet-, Contourlet-, Shearlet- and Hart-Smith-transform. Essentially, two di erent questions are considered: How these transforms can characterize H older regularity and how non-linear approximation of a piecewise smooth function converges. In study of Hölder regularities, several theorems that relate regularity of a function f : R2 → R to decay properties of its transform are presented. Of particular interest is the case where a function has lower regularity along some line segment than elsewhere. Theorems that give estimates for direction and location of this line, and regularity of the function are presented. Numerical demonstrations suggest also that similar theorems would hold for more general shape of segment of low regularity. Theorems related to uniform and pointwise Hölder regularity are presented as well. Although none of the theorems presented give full characterization of regularity, the su cient and necessary conditions are very similar. Another theme of the thesis is the study of convergence of non-linear M ─term approximation of functions that have discontinuous on some curves and otherwise are smooth. With particular smoothness assumptions, it is well known that squared L2 approximation error is O(M-2(logM)3) for curvelet, shearlet or contourlet bases. Here it is shown that assuming higher smoothness properties, the log-factor can be removed, even if the function still is discontinuous.

Identidade molecular dos fitoplasmas associados aos enfezamentos do tomateiro e da berinjela com base na análise do gene 16S rDNA

Doenças de hortaliças de ocorrência no território brasileiro e em outras áreas do mundo têm sido associadas a diversos fitoplasmas. Na região de Piracicaba-SP e Bragança Paulista-SP, em plantas de tomate e berinjela foram observados sintomas típicos de enfezamento caracterizados por porte reduzido, clorose foliar, superbrotamento de ramos, desenvolvimento anormal do cálice, encurtamento de entre-nós, redução no tamanho de folhas, flores e frutos. Através de duplo PCR, utilizando os iniciadores R16 mF1/mR2 e R16 F2n/R2, fragmentos de DNA de 1,2 kb foram amplificados de amostras sintomáticas, demonstrando a presença de fitoplasma nos tecidos das plantas. O uso de iniciadores específicos demonstrou que estes fitoplasmas eram afiliados ao grupo 16SrIII. Análises de RFLP, usando as enzimas de restrição AluI, HpaII, KpnI, MboI, MseI e RsaI confirmaram que os fitoplasmas detectados eram representantes do grupo 16SrIII. Os fragmentos de DNA amplificados foram clonados em Escherichia coli, sequenciados e comparados, por homologia de seqüência, entre si e com outros fitoplasmas do grupo 16SrIII. Um índice de similaridade de seqüência acima de 95% foi encontrado quando seqüências dos fitoplasmas detectados em tomate e berinjela foram comparadas com aquelas de outros representantes do grupo 16SrIII. Um índice de 98-99% foi obtido quando seqüências dos fitoplasmas encontrados em tomate e berinjela foram comparadas entre si. Estes resultados evidenciaram que o enfezamento do tomateiro e da berinjela podem estar associados a um mesmo fitoplasma, com base na análise de seqüências do gene do 16S rDNA.