Processing and compressive strength of Al-Li-SiCp composites fabricated by a compound billet technique

Al-Li-SiCp composites were fabricated by a simple and cost effective stir casting technique. A compound billet technique has been developed to overcome the problems encountered during hot extrusion of these composites. After successful fabrication hardness measurement and room temperature compressive test were carried out on 8090 Al and its composites reinforced with 8, 12 and 18vol.% SiC particles in as extruded and peak aged conditions. The addition of SiC increases the hardness. 0.2% proof stress and compressive strength of Al-Li-8%SiC and Al-Li-12%SiC composites are higher than the unreinforced alloy. in case of the Al-Li-18%SiC composite, the 0.2% proof stress and compressive strength were higher than the unreinforced alloy but lower than those of Al-Li-8%SiC and Al-Li-12%SiC composites. This is attributed to clustering of particles and poor interfacial bonding.

An eigenproblem approach to classical screw theory

This paper presents a novel algebraic formulation of the central problem of screw theory, namely the determination of the principal screws of a given system. Using the algebra of dual numbers, it shows that the principal screws can be determined via the solution of a generalised eigenproblem of two real, symmetric matrices. This approach allows the study of the principal screws of the general two-, three-systems associated with a manipulator of arbitrary geometry in terms of closed-form expressions of its architecture and configuration parameters. We also present novel methods for the determination of the principal screws for four-, five-systems which do not require the explicit computation of the reciprocal systems. Principal screws of the systems of different orders are identified from one uniform criterion, namely that the pitches of the principal screws are the extreme values of the pitch.The classical results of screw theory, namely the equations for the cylindroid and the pitch-hyperboloid associated with the two-and three-systems, respectively have been derived within the proposed framework. Algebraic conditions have been derived for some of the special screw systems. The formulation is also illustrated with several examples including two spatial manipulators of serial and parallel architecture, respectively.

Noninvasive imaging of atheromatous carotid plaques

Atherothrombosis is a systemic disease of the arterial wall that affects the carotid, coronary, and peripheral vascular beds, and the aorta. This condition is associated with complications such as stroke, myocardial infarction, and peripheral vascular disease, which usually result from unstable atheromatous plaques. The study of atheromatous plaques can provide useful information about the natural history and progression of the disease, and aid in the selection of appropriate treatment. Plaque imaging can be crucial in achieving this goal. In this Review, we focus on the various noninvasive imaging techniques that are being used for morphological and functional assessment of carotid atheromatous plaques in the clinical setting.

Scheme of squares: Part I. Systems formalism for potentiostatic studies

The so-called “Scheme of Squares”, displaying an interconnectivity of heterogeneous electron transfer and homogeneous (e.g., proton transfer) reactions, is analysed. Explicit expressions for the various partial currents under potentiostatic conditions are given. The formalism is applicable to several electrode geometries and models (e.g., semi-infinite linear diffusion, rotating disk electrodes, spherical or cylindrical systems) and the analysis is exact. The steady-state (t→∞) expressions for the current are directly given in terms of constant matrices whereas the transients are obtained as Laplace transforms that need to be inverted by approximation of numerical methods. The methodology employs a systems approach which replaces a system of partial differential equations (governing the concentrations of the several electroactive species) by an equivalent set of difference equations obeyed by the various partial currents.

Genetic analysis of resistance to root-lesion nematode (Pratylenchus thornei) in wheat

The inheritance of resistance to root-lesion nematode was investigated in five synthetic hexaploid wheat lines and two bread wheat lines using a half-diallel design of F1 and F2 crosses. The combining ability of resistance genes in the synthetic hexaploid wheat lines was compared with the performance of the bread wheat line 'GS50a', the source of resistance to Pratylenchus thornei used in Australian wheat breeding programmes. Replicated glasshouse trials identified P. thornei resistance as polygenic and additive in gene action. General combining ability (GCA) of the parents was more important than specific combining ability (SCA) effects in the inheritance of P. thornei resistance in both F1 and F2 populations. The synthetic hexaploid wheat line 'CPI133872' was identified as the best general combiner, however, all five synthetic hexaploid wheat lines possessed better GCA than 'GS50a'. The synthetic hexaploid wheat lines contain novel sources of P. thornei resistance that will provide alternative and more effective sources of resistance to be utilized in wheat breeding programmes

Effects of Nutrition and Time of Weaning on Dry Season Liveweight Loss of Breeder Cows

In the seasonally dry tropics of northern Australia, breeder cows may lose up to 30% liveweight during the dry season when pasture is of low nutritive value. This is a major cause of low reproductive rates and high mortality. Weaning early in the dry season is effective to reduce this liveweight loss of the breeder (Holroyd et al. 1988). An experiment examined the dry season liveweight loss of breeders for a range of weaning times and levels of nutrition. From April to October through the dry season, 209 Bos indicus x Shorthorn cross cows 4-6 years of age grazed speargrass pastures in north Queensland. The cows had been joined with bulls from late January until April. Twenty-nine breeders had not suckled a calf during the previous wet season (DRY cows). In addition 180 cows lactating in April were weaned in late April, mid July or early September. The cows were allocated by stratified randomisation based on lactational status, stage of pregnancy and body condition to 15 x 40 ha paddocks. Five paddocks with low fertility soils provided LOW nutrition, while 10 paddocks with medium fertility soils and no supplementation or with supplementation provided MEDIUM and HIGH nutrition, respectively. The supplement consisted of molasses containing 14% urea offered ad libitum. Liveweight was measured at intervals and conceptus-free liveweight (CF-LW) calculated. Data were analyses by AOV within groups of paddocks. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Use of electronic portal imaging devices for electron treatment verification

This study aims to help broaden the use of electronic portal imaging devices (EPIDs) for pre-treatment patient positioning verification, from photon-beam radiotherapy to photon- and electron-beam radiotherapy, by proposing and testing a method for acquiring clinicallyuseful EPID images of patient anatomy using electron beams, with a view to enabling and encouraging further research in this area. EPID images used in this study were acquired using all available beams from a linac configured to deliver electron beams with nominal energies of 6, 9, 12, 16 and 20 MeV, as well as photon beams with nominal energies of 6 and 10 MV. A widely-available heterogeneous, approximately-humanoid, thorax phantom was used, to provide an indication of the contrast and noise produced when imaging different types of tissue with comparatively realistic thicknesses. The acquired images were automatically calibrated, corrected for the effects of variations in the sensitivity of individual photodiodes, using a flood field image. For electron beam imaging, flood field EPID calibration images were acquired with and without the placement of blocks of water-equivalent plastic (with thicknesses approximately equal to the practical range of electrons in the plastic) placed upstream of the EPID, to filter out the primary electron beam, leaving only the bremsstrahlung photon signal. While the electron beam images acquired using a standard (unfiltered) flood field calibration were observed to be noisy and difficult to interpret, the electron beam images acquired using the filtered flood field calibration showed tissues and bony anatomy with levels of contrast and noise that were similar to the contrast and noise levels seen in the clinically acceptable photon beam EPID images. The best electron beam imaging results (highest contrast, signal-to-noise and contrast-to-noise ratios) were achieved when the images were acquired using the higher energy electron beams (16 and 20 MeV) when the EPID was calibrated using an intermediate (12 MeV) electron beam energy. These results demonstrate the feasibility of acquiring clinically-useful EPID images of patient anatomy using electron beams and suggest important avenues for future investigation, thus enabling and encouraging further research in this area. There is manifest potential for the EPID imaging method proposed in this work to lead to the clinical use of electron beam imaging for geometric verification of electron treatments in the future.

Age-related alterations of immunoreactive pancreatic cationic trypsinogen in sera from cystic fibrosis patients with and without pancreatic insufficiency

Serum immunoreactive cationic trypsinogen levels were determined in 99 control subjects and 381 cystic fibrosis (CF) patients. To evaluate the status of the exocrine pancreas all CF patients had previously undergone fecal fat balance studies and/or pancreatic stimulation tests. Three hundred fourteen CF patients had fat malabsorption and/or had inadequate pancreatic enzyme secretion (pancreatic insufficiency) requiring oral pancreatic enzyme supplements with meals. Sixty-seven CF patients did not have fat malabsorption and/or had adequate enzyme secretion (pancreatic sufficiency) and were not receiving pancreatic enzyme supplements with meals. Mean serum trypsinogen in 99 control subjects was 31.4 ± 14.8 /µg/hter (± 2 SD) and levels did not vary with age or sex. In CF infants (< 2 yr) with pancreatic insufficiency, mean serum trypsinogen was significantly above the non-CF values (p < 0.001). Ninety-one percent of the CF infants had elevated levels. Serum trypsinogen values in the pancreatic insuffi ient group declined steeply up to 5 years, reaching subnormal values by age 6. An equation was developed which described these age-related changes very accurately. Only six CF patients with pancreatic insufficiency had serum trypsinogen levels above the 95% confidence limits of this equation. In contrast, there was no age related decline in serum trypsinogen among the CF group with pancreatic sufficiency. Under 7 yr, serum trypsinogen failed to distinguish the two groups. In those over 7 yr of age, however, serum trypsinogen was significantly higher than the CF group with pancreatic insufficiency (p < 0.001), and 93% had values within or above the control range. In conclusion, serum trypsinogen appears to be a useful screening test for CF in infancy. Between 2 and 7 yr of age this test is of little diagnostic value. After 7 yr of age, serum trypsinogen can reliably distinguish between CF patients with and without pancreatic insufficiency.

Thermoanalysis of ammonium perchlorate and sodium nitrate mixture

A binary mixture of ammonium perchlorate-sodium nitrate in molar proportion undergoes partial fusion at 223°C and the transformation of the mixture to sodium perchlorate-ammonium nitrate occurs in the broad endothermic region. The mixture was heated and quenched at various temperatures in a differential thermal analysis assembly. Thermogravimetric analysis, X-ray diffraction, and infrared spectroscopic techniques were used to determine the composition of the quenched sample in order to explain the overall thermal phenomenon. Visual observations of the morphological changes that occur during the course of heating were made using a hot-stage microscope, 30–350°C.

New records of the River Shark Glyphis (Carcharhinidae) reported from Cape York Peninsula, northern Australia

The distribution of the river shark Glyphis in northern Australia is extended with new records of occurrence in the Gulf of Carpentaria and a reassessment of historical survey data from Cape York Peninsula. Nine new specimens of Glyphis sp. A were collected in 2005 from the Weipa region on the Queensland coast of the Gulf of Carpentaria. A re-examination of archival records from 1978-86 marine and estuarine fish surveys in the Gulf of Carpentaria and along the northern Queensland East Coast allowed a further nineteen Glyphis specimens to be identified. Combined this gives twenty-eight new records of Glyphis specimens from the coasts of Cape York Peninsula, Queensland. Common habitat characteristics for all captures were turbid, shallow, fast running tidal water in the upper reaches of coastal rivers. The substrate was generally muddy and the rivers lined with mangrove. In all surveys the representation of Glyphis was low, being less than 1% of the total shark captures historically and 0.002 sharks 50 m net hour-1 in Weipa 2005. The size range captured was 1000-1800 mm total length historically and 705-1200 mm total length from Weipa 2005, with none recorded as sexually mature. Diagnostic characteristics of the Weipa specimens, identified as Glyphis sp. A, were: lower jaw teeth protruding and "spear-like"; second dorsal fin greater than half the height of the first dorsal fin; the snout relatively short and fleshy in the lateral view; pectoral fin ventral surface black in colouration; the precaudal vertebral count between 118 and 123; and the total vertebral count between 204 and 209.

Pulsed laser surface treatment of magnesium alloy: Correlation between thermal model and experimental observations

The effect of deposition of Al +Al2O3 on MRI 153 M Mg alloy processed using a pulsed Nd:YAG laser is presented in this study. A composite coating with metallurgical joint to the substrate was formed. The microstructure and phase constituents were characterized and correlated with the thermal predictions. The laser scan speed had an effect on the average melt depth and the amount of retained and/or reconstituted alumina in the final coating. The coating consisted of alumina particles and highly refined dendrites formed due to the extremely high cooling rates (of the order of 10(8) K/s). The microhardness of the coating was higher and several fold improvement of wear resistance compared to the substrate was observed for the coatings. These microstructural features and physical properties were correlated with the effects predicted by a thermal model.

Acyclic Edge Coloring of Graphs with Maximum Degree 4

An acyclic edge coloring of a graph is a proper edge coloring such that there are no bichromatic cycles. The acyclic chromatic index of a graph is the minimum number k such that there is an acyclic edge coloring using k colors and is denoted by a'(G). It was conjectured by Alon, Sudakov, and Zaks that for any simple and finite graph G, a'(G) <= Delta+2, where Delta=Delta(G) denotes the maximum degree of G. We prove the conjecture for connected graphs with Delta(G)<= 4, with the additional restriction that m <= 2n-1, where n is the number of vertices and m is the number of edges in G. Note that for any graph G, m <= 2n, when Delta(G)<= 4. It follows that for any graph G if Delta(G)<= 4, then a'(G) <= 7.

Detection and characterisation of strong resistance to phosphine in Brazilian Rhyzopertha dominica (F.) (Coleoptera: Bostrychidae)

As failure to control Rhyzopertha dominica (F.) with phosphine is a common problem in the grain-growing regions of Brazil, a study was undertaken to investigate the frequency, distribution and strength of phosphine resistance in R. dominica in Brazil. Nineteen samples of R. dominica were collected between 1991 and 2003 from central storages where phosphine fumigation had failed to control this species. Insects were cultured without selection until testing in 2005. Each sample was tested for resistance to phosphine on the basis of the response of adults to discriminating concentrations of phosphine (20 and 48 h exposures) and full dose-response assays (48 h exposure). Responses of the Brazilian R. dominica samples were compared with reference susceptible, weak-resistance and strong-resistance strains from Australia in parallel assays. All Brazilian population samples showed resistance to phosphine: five were diagnosed with weak resistance and 14 with strong resistance. Five samples showed levels of resistance similar to the reference strong-resistance strain. A representative highly resistant sample was characterised by exposing mixed-age cultures to a range of constant concentrations of phosphine for various exposure periods. Time to population extinction (TPE) and time to 99.9% suppression of population (LT99.9) values of this sample were generally similar to those of the reference strong-resistance strain. For example, at 0.1, 0.5 and 1.0 mg L-1, LT99.9 values for BR33 and the reference strong-resistance strain were respectively 21, 6.4 and 3.7 days and 17, 6.2 and 3.8 days. With both strains, doubling phosphine concentrations to 2 mg L -1 resulted in increased LT99.9 and TPE. High level and frequency of resistance in all population samples, some of which had been cultured without selection for up to 12 years, suggest little or no fitness deficit associated with phosphine resistance. The present research indicates that widespread phosphine resistance may be developing in Brazil. Fumigation practices should be monitored and resistance management plans implemented to alleviate further resistance development.

Social and physical environments in senior communities: The Finnish experience

Purpose – The purpose of this paper is to discuss residents’ views of social and physical environments in a co-housing and in a senior housing setting in Finland. Also, the study aims to point out important connections between well-being and built environment. Design/methodology/approach – The data include interviews and survey responses gathered in the cases. The results and analysis are presented at different case study levels, with the discussion and conclusions following this. Findings – The findings show that the physical environment and common areas have an important role to activate residents. When well-designed common areas exist, a higher level of engagement can be achieved by getting residents involved in the planning and running of activities. Research limitations/implications – This paper discusses residents’ experiences in two Finnish housing settings and it focuses on the housing market in Finland. Practical implications – The findings encourage investors and housing operators to design and invest common areas which could activate residents and create social contacts. Also, investors have to pay attention to the way these developments are managed. Originality/value – This study is the first to investigate the Finnish co-housing setting and compare social and physical environments in a co-housing and a senior house.