Carbon dioxide assimilation rate, gas and ion composition in samples, and bacterial production of organic matter within and above the Broken Spur and TAG hydrothermal fields, Mid-Atlantic Ridge

Rate of CO2 assimilation was determined above the Broken Spur and TAG active hydrothermal fields for three main ecosystems: (1) hydrothermal vents; (2) 300 m near-bottom layer of plume water; and (3) bottom sediments. In water samples from warm (40-45°C) vents assimilation rates were maximal and reached 2.82-3.76 µg C/l/day. In plume waters CO2 assimilation rates ranged from 0.38 to 0.65 µg C/l/day. In bottom sediments CO2 assimilation rates varied from 0.8 to 28.0 µg C/l/day, rising up to 56 mg C/kg/day near shrimp swarms. In the most active plume zone of the long-living TAG field bacterial production of organic matter (OM) from carbonic is up to 170 mg C/m**2/day); production of autotrophic process of bacterial chemosynthesis reaches about 90% (156 mg C/m**2/day). Thus, chemosynthetic production of OM in September-October is almost equal to that of photosynthetic production in the oceanic region. Bacterial production of OM above the Broken Spur hydrothermal field is one order lower and reaches only 20 mg C/m**2/day.

Sulfur geochemistry at ODP Site 112-680 and 112-686

We have measured the concentrations of (1) pore-water sulfide and (2) solid-phase pyrite, iron monosulfide (=acid volatile sulfide), elemental sulfur, and extractable and nonextractable organic ("kerogen") sulfur in sediments from Ocean Drilling Program (ODP) Sites 680 and 686. Pore-water sulfide defines classic "bell-shaped" profiles. Maximum concentrations of 6 to 12 mM occur where sulfate is exhausted, or is most depleted, at depths between 15 and 50 mbsf. Sulfide resulting from bacterial sulfate reduction reacts in three ways: (1) some is reoxidized to elemental sulfur in surface sediments; (2) some reacts with detrital iron minerals to form iron monosulfide and pyrite, primarily in the top meter or two of the sediment; and (3) some reacts with, and is incorporated into, kerogen. Incorporation of reduced sulfur into kerogen occurs over the top 15 m of the sediment at both Sites 680 and 686, after the main phase of pyrite formation. Up to 45% of the total sedimentary sulfur is organically bound, and concentrations of 12 wt% sulfur are reached in the kerogen. These values are like those measured in lithologically similar, but more deeply buried, sediments from the Monterey Formation.

Precipitation of the sulphides of nickel & cobalt in an alkaline tartrate solution : together with an investigation into the nature of certain tartrates of these metals.

Reprinted from the Journal of the American chemical society, v. 22, no. 8, Ag. 1900.

Hydrogen sulfide health effects and recommended air quality standard : prepared for the Illinois Institute for Environmental Quality /

Includes bibliographical references.

Growing semiconductor nanocrystals directly in a conducting polymer

We describe a single step method to synthesise lead sulphide (PbS) nanocrystals directly in the conjugated polymer poly (2-methoxy-5-(2'-ethyl-hexyloxy)-p-phenylene vinylene) (MEH-PPV). This method allows size control of the nanocrystal via co-solvent ratios. We find good agreement between nanocrystal sizes determined by transmission electron microscopy and sizes theoretically determined from the absorption edge of the nanocrystals. Finally we show that this synthesis technique is not restricted to MEH-PPV and demonstrate that nanocrystals can be grown in Poly(3-hexylthiophene-2,5-diyl) (P3HT). (C) 2005 Elsevier B.V. All rights reserved.

Variation in mangrove forest structure and sediment characteristics in Bocas del Toro, Panama

Mangrove forest structure and sediment characteristics were examined in the extensive mangroves of Bocas del Toro, Republic of Panama. Forest structure was characterized to determine if spatial vegetation patterns were repeated over the Bocas del Toro landscape. Using a series of permanent plots and transects we found that the forests of Bocas del Toro were dominated by Rhizophora maugle with very few individuals of Avicennia germinans and Laguncularia racemosa. Despite this low species diversity, there was large variation in forest structure and in edaphic conditions (salinity, concentration of available phosphorus, Eh and sulphide concentration). Aboveground biomass varied 20-fold, from 6.8 Mg ha(-1) in dwarf forests to 194.3 Mg ha(-1) in the forests fringing the land. But variation in forest structure was predictable across the intertidal zone. There was a strong tree height gradient from seaward fringe (mean tree height 3.9 m), decreasing in stature in the interior dwarf forests (mean tree height 0.7 m), and increasing in stature in forests adjacent to the terrestrial forest (mean tree height 4.1 m). The predictable variation in forest structure emerges due to the complex interactions among edaphic and plant factors. Identifying predictable patterns in forest structure will aid in scaling up the ecosystem services provided by mangrove forests in coastal landscapes.

Carrier transport in PbS nanocrystal conducting polymer composites

In this letter we report the carrier mobilities in an inorganic nanocrystal: conducting polymer composite. The composite material in question (lead sulphide nanocrystals in the conducting polymer poly [2-methoxy-5-(2(')-ethyl-hexyloxy)-p-phenylene vinylene] (MEH-PPV) was made using a single-pot, surfactant-free synthesis. Mobilties were measured using time of flight techniques. We have found that the inclusion of PbS nanocrystals in MEH-PPV both balances and markedly increases the hole and electron mobilities-the hole mobility is increased by a factor of similar to 10(5) and the electron mobility increased by similar to 10(7) under an applied bias of 5 kV cm(-1). These results explain why dramatic improvements in electrical conductivity and photovoltaic performance are seen in devices fabricated from these composites.

A new estimate for the composition of weathered young upper continental crust from alluvial sediments, Queensland, Australia

We present new major element, trace element and Nd-isotope data for 30 alluvial sediments collected from 25 rivers in Queensland, E Australia. Samples were chosen to represent drainage from the region's most important lithologies, including Tertiary intraplate volcanic rocks, a Cretaceous igneous province (and sedimentary rocks derived thereof) as well as Proterozoic blocks. In most chemical and isotopic aspects, the alluvial sediments represent binary or ternary mixing relationships, with absolute abundances implied to reflect the proportion of lithologies in the catchments. When averaged, the studied sediments differ from other proxies of upper continental crust (UCC) mainly in their relative middle rare earth element enrichment (including an elevated Sm/Nd ratio), higher relative Eu abundance and higher Nb/Ta ratio. These features are inherited from eroded Tertiary intraplate basalts, which commonly form topographic highs in the studied region. Despite the high degree of weathering strong to excellent coherence between similarly incompatible elements is found for all samples. From this coherence, we suggest revisions of the following upper crustal element ratios: Y/Ho = 26.2, Yb/Tm = 6.37, Th/W = 7.14, Th/Tl = 24 and Zr/Hf = 36.9. Lithium, Rb, Cs and Be contents do not seem depleted relative to UCC, which may reflect paucity of K-feldspar in the eroded catchments. Nickel, Cr, Pb, Cu and Zn concentrations are elevated in polluted rivers surrounding the state capital. River sediments in the Proterozoic Georgetown Inlier are elevated in Pb, Cu and Zn but this could be a natural phenomenon reflecting abundant sulphide mineralisation in the area. Except for relative Sr concentrations, which broadly anticorrelate with mean annual rainfall in catchments, there is no obvious relationship between the extent of weathering and climate types, which range from and to tropical. The most likely explanation for this observation is that the weathering profiles in many catchments are several Myr old, established during the much wetter Miocene period. The studied sediment compositions (excluding those from the Proterozoic catchments) are used to propose a new trace element normalisation termed MUQ (MUd from Queensland), which serves as an alternative to UCC proxies derived from sedimentary rocks. Copyright (C) 2005 Elsevier Ltd

Chemistry of acid production in black coal mine washery wastes

Column leaching tests on black coal mine washery wastes were performed, to determine the chemistry of acid generation. Coal mine coarse rejects and tailings were subjected to wet and dry cycle dissolution and subsequently column leached. The rates of iron sulphide oxidation and carbonate mineral dissolution were determined based on the drainage chemistry. The kinetic data from column leach experiments are used to predict the time required to deplete the acid producing and acid consuming minerals in the mine wastes. The acid production in the mine rejects was found to depend upon iron chemistry, carbonate chemistry, diffusion of oxygen, and permeability. The chemistry of the drainage from two different coal mines is compared. (c) 2005 Elsevier B.V. All rights reserved.

Eliminating non-renewable CO2 emissions from sewage treatment: An anaerobic migrating bed reactor pilot plant study

The aim of this work was to demonstrate at pilot scale a high level of energy recovery from sewage utilising a primary Anaerobic Migrating Bed Reactor (AMBR) operating at ambient temperature to convert COD to methane. The focus is the reduction in non-renewable CO2 emissions resulting from reduced energy requirements for sewage treatment. A pilot AMBR was operated on screened sewage over the period June 2003 to September 2004. The study was divided into two experimental phases. In Phase 1 the process operated at a feed rate of 10 L/h (HRT 50 h), SRT 63 days, average temperature 28 degrees C and mixing time fraction 0.05. In Phase 2 the operating parameters were 20 L/h, 26 days, 16 degrees C and 0.025. Methane production was 66% of total sewage COD in Phase 1 and 23% in Phase 2. Gas mixing of the reactor provided micro-aeration which suppressed sulphide production. Intermittent gas mixing at a useful power input of 6 W/m(3) provided satisfactory process performance in both phases. Energy consumption for mixing was about 1.5% of the energy conversion to methane in both operating phases. Comparative analysis with previously published data confirmed that methane supersaturation resulted in significant losses of methane in the effluent of anaerobic treatment systems. No cases have been reported where methane was considered to be supersaturated in the effluent. We have shown that methane supersaturation is likely to be significant and that methane losses in the effluent are likely to have been greater than previously predicted. Dissolved methane concentrations were measured at up to 2.2 times the saturation concentration relative to the mixing gas composition. However, this study has also demonstrated that despite methane supersaturation occurring, microaeration can result in significantly lower losses of methane in the effluent (< 11% in this study), and has demonstrated that anaerobic sewage treatment can genuinely provide energy recovery. The goal of demonstrating a high level of energy recovery in an ambient anaerobic bioreactor was achieved. An AMBR operating at ambient temperature can achieve up to 70% conversion of sewage COD to methane, depending on SRT and temperature. (c) 2006 Wiley Periodicals, Inc.

Integration of sulphate reduction, autotrophic denitrification and nitrification to achieve low-cost excess sludge minimisation for Hong Kong sewage

An integrated anaerobic-aerobic treatment system of sulphate-laden wastewater was proposed here to achieve low sludge production, low energy consumption and effective sulphide control. Before integrating the whole system, the feasibility of autotrophic denitrification utilising dissolved sulphide produced during anaerobic treatment of sulphate rich wastewater was studied here. An upflow anaerobic sludge blanket reactor was operated to treat sulphate-rich synthetic wastewater (TOC = 100 mg/L and sulphate = 500 mg/L) and its effluent with dissolved sulphide and external nitrate solution were fed into an anoxic biofilter. The anaerobic reactor was able to remove 77-85% of TOC at HRT of 3 h and produce 70-90 mg S/L sulphide in dissolved form for the subsequent denitrification. The performance of anoxic reactor was stable, and the anoxic reactor could remove 30 mg N/L nitrate at HRT of 2 h through autotrophic denitrification. Furthermore, sulphur balance for the anoxic filter showed that more than 90% of the removed sulphide was actually oxidised into sulphate, thereby there was no accumulation of sulphur particles in the filter bed. The net sludge productions were approximately 0.15 to 0.18 g VSS/g COD in the anaerobic reactor and 0.22 to 0.31 g VSS/g NO3--N in the anoxic reactor. The findings in this study will be helpful in developing the integrated treatment system to achieve low-cost excess sludge minimisation.

Nonmetallic inclusion modification and its effect on the final properties of a linepipe steel

Five linepipe type steels were produced in order to study the effect of calcium and magnesium injection on their final properties. Two of these steels were at the extremes of the sulphide range i.e. 0.003 and 0.017% sulphur with no injection attempted; thereby, providing standards to compare with the injected steels. The oxygen level varied from 21 to 63 p.p.m. The cast ingots were controlled-rolled and isothermally rolled in order to study the deformation characteristics of the residual non-metallic inclusions. The structure and cleanliness of these steels was evaluated metallographically using the light microscope, SEM, and image analysis and the results related to their Charpy toughness and HIC resistance. Increasing sulphur levels decreased final properties of the steel. In the untreated state, with as little as 0.003% sulphur, test orientation was highly influential. Modification of sulphur bearing steels was achieved with low modifying element to sulphur ratios provided that the oxygen content was very low. Injection of calcium into steel caused interaction with oxide and sulphide inclusions which was biased toward oxide reduction relative to sulphur removal. Magnesium again reduced oxides and appeared to be linked with aluminia containing inclusions in the final product. It produced improved toughness values relative to a similar sulphur containing calcium treated steel. The results of this work could be extended to establish the mechanism of inclusion modification with magnesium additions to sulphur bearing steels.

Effect of pulsed current on the electrodeposition of chromium and copper

This research was concerned with the effects of pulsed current on the electrodeposition of chromium and copper. In the case of the latter metal, a novel application has been studied and a theory proposed for the ability to improve throwing power by the joint use of organic additives and pulsed reverse current. During the course of the research, several improvements were made to the pulse plating unit.Chromium. A study was made of the effect of square wave pulsed current on various physical properties of deposits from three hard chromium plating electrolytes. The effect of varying frequency at a duty cycle of 50% on the mean bulk internal stress, visual appearance, hardness, crack characteristics and surface topography of the electrodeposits was determined. X-ray diffraction techniques were used to study the phases present in the deposits. The effect of varying frequency on the cathodic efficiencies of the electrolytes was also determined. It was found that pulsed current reduced the internal stress of deposits from the sulphate catalysed electrolyte. It also reduced or eliminated cracking of deposits and reduced deposit brightness. Under certain conditions, pulsed current was found to induce the co-deposition of hydrides of chromium. Deposit hardness was found to be reduced by the use of pulsed current. Cathodic efficiencies of the high efficiency electrolytes were reduced by use of pulsed current although this effect was minimised at high frequencies. The sulphate catalysed electrolyte showed an increase in efficiency over the frequency range where hydrides were co-deposited.Copper. The polarisation behaviour of acid copper solutions containing polyethers, sulphopropyl sulphides and chloride ions was studied using both direct and pulse reverse current. The effect of these additives on the rest potentials of copper deposits immersed in the electrolyte was also studied. Hole Throwing Power on printed circuit boards was determined using a specially designed test cell. The effect of pulsed reverse current on the hole throwing power of commercially produced printed circuit boards was also studied. Polyethers were found to have an inhibiting effect on the deposition of copper whereas the sulphopropyl sulphides produced a stimulating (i.e. depolarising) effect. Studies of rest potentials made when both additives were present indicated that the sulphopropyl sulphide was preferentially adsorbed. The use of pulsed reverse current in solutions containing both polyether and sulphopropyl sulphide was found to cause desorption of the sulphopropyl sulphide at the cathode surface. Thus, at higher current densities, the inhibiting effect of the polyether produced an increase in the cathodic polarisation potential. At lower current densities, the depolarisation effect of the sulphopropyl sulphide could still occur. On printed circuit boards, this effect was found to produce an increase in the `hole throwing power' due to depolarisation of the holes relative to the surface of the boards. Typically, using direct current, hole/surface thickness ratios of 40% were obtained when plating 0.6 mm holes in a 3.2 mm thick board at a current density of 3 A/dm2 whereas using pulsed reverse current, ratios of 80% could be obtained at an equivalent rate of deposition. This was observed both in laboratory tests and on commercially plated boards.

Palaeozoic volcanogenic mineral deposits at Parys Mountain, Avoca, and S.E. Canada: a comparative study. Available in 2 volumes.

The sulphide mineralisation at Avoca and Parys Mountain is intimately related to volcanism and is of volcanogenic sedimentary type. The associated volcanics are predominantly pyroclastics of rhyodacitic composition and of Upper Ordovician age. They were erupted from discrete small volcanic centres, products of single local volcanic events, whose spatial distribution was related to fractures in the sialic basement of the paratectonic Caledonides of the British Isles. These fractures resulted in linear controls on volcanic, plutonic and tectonic features; they are the result of predominantly strikeslip stresses generated in this part of the European plate during closure of the Iapetus ocean. The mineralisation, predominantly pyritic, consists of a siliceous footwall zone containing bedded and cross-cutting sulphides and an overlying non-siliceous zone of bedded sulphides which may show vertical zoning of metal ratios. The sulphides are associated with chert and iron formation and have been affected by slumping. Mineralisation developed near the vents during intense fumarolic activity accompanying strong volcanism; at Parys Mountain, fumarolic activity commenced prior to, and continued after, the rnain volcanic event. Comparison with similar deposits in Newfoundland and at Bathurst, in the Canadian Appalachians, shows that mineralisation can be associated with any discrete pulse of acid magmatism in shallow subaqueous conditions. Local features of the sulphides and associated sediments are similar, although in more distal deposits (with respect to a volcanic centre) footwall alteration and mineralisation are less well developed. The nature of the basement and the presence or absence of earlier volcanics are not critical, although establishment of a local tensional regime at the time of ore formation may be important. The volcanics hosting mineralisation are rhyodacitic pyroclastics, generally related to a small centre and representing a single episode of volcanism.

Diagenetic processes in ore formation with special reference to the Zambian copperbelt and permian marl slate.

This thesis is concerned with the role of diagenesis in forming ore deposits. Two sedimentary 'ore-types' have been examined; the Proterozoic copper-cobalt orebodies of the Konkola Basin on the Zambian Copperbelt, and the Permian Marl Slate of North East England. Facies analysis of the Konkola Basin shows the Ore-Shale to have formed in a subtidal to intertidal environment. A sequence of diagenetic events is outlined from which it is concluded that the sulphide ores are an integral part of the diagenetic process. Sulphur isotope data establish that the sulphides formed as a consequence of the bacterial reduction of sulphate, while the isotopic and geochemical composition of carbonates is shown to reflect changes in the compositions of diagenetic pore fluids. Geochemical studies indicate that the copper and cobalt bearing mineralising fluids probably had different sources. Veins which crosscut the orebodies contain hydrocarbon inclusions, and are shown to be of late diagenetic lateral secretion origin. RbiSr dating indicates that the Ore-Shale was subject to metamorphism at 529 A- 20 myrs. The sedimentology and petrology of the Marl Slate are described. Textural and geochemical studies suggest that much of the pyrite (framboidal) in the Marl Slate formed in an anoxic water column, while euhedral pyrite and base metal sulphides formed within the sediment during early diagenesis. Sulphur isotope data confirm that conditions were almost "ideal" for sulphide formation during Marl Slate deposition, the limiting factors in ore formation being the restricted supply of chalcophile elements. Carbon and oxygen isotope data, along with petrographic observations, indicate that much of the calcite and dolomite occurring in the Marl Slate is primary, and probably formed in isotopic equilibrium. A depositional model is proposed which explains all of the data presented and links the lithological variations with fluctuations in the anoxicioxic boundary layer of the water column.