Performance-Based Engineering Framework for Earthquake and Fire Following Earthquake

The objective for this thesis is to outline a Performance-Based Engineering (PBE) framework to address the multiple hazards of Earthquake (EQ) and subsequent Fire Following Earthquake (FFE). Currently, fire codes for the United States are largely empirical and prescriptive in nature. The reliance on prescriptive requirements makes quantifying sustained damage due to fire difficult. Additionally, the empirical standards have resulted from individual member or individual assembly furnace testing, which have been shown to differ greatly from full structural system behavior. The very nature of fire behavior (ignition, growth, suppression, and spread) is fundamentally difficult to quantify due to the inherent randomness present in each stage of fire development. The study of interactions between earthquake damage and fire behavior is also in its infancy with essentially no available empirical testing results. This thesis will present a literature review, a discussion, and critique of the state-of-the-art, and a summary of software currently being used to estimate loss due to EQ and FFE. A generalized PBE framework for EQ and subsequent FFE is presented along with a combined hazard probability to performance objective matrix and a table of variables necessary to fully implement the proposed framework. Future research requirements and summary are also provided with discussions of the difficulties inherent in adequately describing the multiple hazards of EQ and FFE.

EU Copyright Law, Lobbying and Transparency of Policy-Making: The cases of sound recordings term extension and orphan works provisions

The objective of this paper is to discuss EU lobbying in the area of copyright. Legislation needs to regulate the legal position of various different stakeholders in a balanced manner. However, a number of EU copyright provisions brought into effect over recent years were highly controversial and have led to suggestions that powerful lobbying forces may have had some influence. This article investigates the effects of lobbying on copyright law-making in Europe. A specific comparative and multi-faceted analysis is provided of the legislative process for two recently adopted directives: 2011/77/EU which extends the term of protection of sound recordings and 2012/28/EU which introduces certain permitted uses of orphan works (some references are also made to the ACTA case). Firstly, a short presentation is given of the legal bases for the EU consultation process and lobbying. Next, an analysis is provided of the two cases, taking into consideration the policy-making procedures (with special focus on how the consultation process was handled), the legal solutions proposed and adopted and the various stakeholders’ claims. Lastly, it asks why some interest groups were successful and some others failed (the analysis identifies two types of factor for the effectiveness of lobbying: those resulting from stakeholders’ actions and those connected with the consultation process).

Softening the Lower Crust: Modes of Syn-Transport Transposition Around and Adjacent to a Deep Crustal Granulite Nappe, Parry Sound Domain, Grenville Province, Ontario, Canada

The Parry Sound domain is a granulite nappe-stack transported cratonward during reactivation of the ductile lower and middle crust in the late convergence of the Mesoproterozoic Grenville orogeny. Field observations suggest the following with respect to the ductile sheath: (1) Formation of a carapace of transposed amphibolite facies gneiss derived from and enveloping the western extremity of the Parry Sound domain and separating it from high-strain gneiss of adjacent allochthons. This ductile sheath formed dynamically around the moving granulite nappe through the development of systems of progressively linked shear zones. (2) Transposition initiated by hydration (amphibolization) of granulite facies gneiss by introduction of fluid along cracks accompanying pegmatite emplacement. Shear zones nucleated along pegmatite margins and subsequently linked and rotated. The source of the pegmatites was most likely subjacent migmatitic and pegmatite-rich units or units over which Parry Sound domain was transported. Comparison of gneisses of the ductile sheath with high-strain layered gneiss of adjacent allochthons show the mode of transposition of penetratively layered gneiss depended on whether or not the gneiss protoliths were amphibolite or granulite facies tectonites before initiation of transposition, resulting in, e.g., folding before shearing, no folding before shearing, respectively. Meter-scale truncation along high-strain gradients at the margins of both types of transposition-related shear zones observed within and marginal to Parry Sound domain mimic features at kilometer scales, implying that apparent truncation by transposition originating in a manner similar to the ductile sheath may be a common feature of deep crustal ductile reworking. Citation: Culshaw, N., C. Gerbi, and J. Marsh (2010), Softening the lower crust: Modes of syn-transport transposition around and adjacent to a deep crustal granulite nappe, Parry Sound domain, Grenville Province, Ontario, Canada, Tectonics, 29, TC5013, doi:10.1029/2009TC002537.

Prediction and prevention of psychosis: current progress and future tasks

Prevention of psychoses has been intensively investigated within the past two decades, and particularly, prediction has been much advanced. Depending on the applied risk indicators, current criteria are associated with average, yet significantly heterogeneous transition rates of ≥30 % within 3 years, further increasing with longer follow-up periods. Risk stratification offers a promising approach to advance current prediction as it can help to reduce heterogeneity of transition rates and to identify subgroups with specific needs and response patterns, enabling a targeted intervention. It may also be suitable to improve risk enrichment. Current results suggest the future implementation of multi-step risk algorithms combining sensitive risk detection by cognitive basic symptoms (COGDIS) and ultra-high-risk (UHR) criteria with additional individual risk estimation by a prognostic index that relies on further predictors such as additional clinical indicators, functional impairment, neurocognitive deficits, and EEG and structural MRI abnormalities, but also considers resilience factors. Simply combining COGDIS and UHR criteria in a second step of risk stratification produced already a 4-year hazard rate of 0.66. With regard to prevention, two recent meta-analyses demonstrated that preventive measures enable a reduction in 12-month transition rates by 54-56 % with most favorable numbers needed to treat of 9-10. Unfortunately, psychosocial functioning, another important target of preventive efforts, did not improve. However, these results are based on a relatively small number of trials; and more methodologically sound studies and a stronger consideration of individual profiles of clinical needs by modular intervention programs are required

Computed Ultrasound Tomography in Echo mode (CUTE) of speed of sound for diagnosis and for aberration correction in pulse-echo sonography

Sound speed as a diagnostic marker for various diseases of human tissue has been of interest for a while. Up to now, mostly transmission ultrasound computed tomography (UCT) was able to detect spatially resolved sound speed, and its promise as a diagnostic tool has been demonstrated. However, UCT is limited to acoustically transparent samples such as the breast. We present a novel technique where spatially resolved detection of sound speed can be achieved using conventional pulse-echo equipment in reflection mode. For this purpose, pulse-echo images are acquired under various transmit beam directions and a two-dimensional map of the sound speed is reconstructed from the changing phase of local echoes using a direct reconstruction method. Phantom results demonstrate that a high spatial resolution (1 mm) and contrast (0.5 % of average sound speed) can be achieved suitable for diagnostic purposes. In comparison to previous reflection-mode based methods, CUTE works also in a situation with only diffuse echoes, and its direct reconstruction algorithm enables real-time application. This makes it suitable as an addition to conventional clinical ultrasound where it has the potential to benefit diagnosis in a multimodal approach. In addition, knowledge of the spatial distribution of sound speed allows full aberration correction and thus improved spatial resolution and contrast of conventional B-mode ultrasound. © (2014) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Computed Ultrasound Tomography in Echo Mode for Imaging Speed of Sound Using Pulse-Echo Sonography: Proof of Principle

The limitations of diagnostic echo ultrasound have motivated research into novel modalities that complement ultrasound in a multimodal device. One promising candidate is speed of sound imaging, which has been found to reveal structural changes in diseased tissue. Transmission ultrasound tomography shows speed of sound spatially resolved, but is limited to the acoustically transparent breast. We present a novel method by which speed-of-sound imaging is possible using classic pulse-echo equipment, facilitating new clinical applications and the combination with state-of-the art diagnostic ultrasound. Pulse-echo images are reconstructed while scanning the tissue under various angles using transmit beam steering. Differences in average sound speed along different transmit directions are reflected in the local echo phase, which allows a 2-D reconstruction of the sound speed. In the present proof-of-principle study, we describe a contrast resolution of 0.6% of average sound speed and a spatial resolution of 1 mm (laterally) × 3 mm (axially), suitable for diagnostic applications.

The Islamic Crossed-Arch Domes in Cordoba: Geometry and Structural Analysis of the “Capilla de Villaviciosa”

Crossed-arch domes are a singular type of ribbed vaults. Their characteristic feature is that the ribs that form the vault are intertwined, forming polygons or stars, leaving an empty space in the centre. The earliest known vaults of this type are found in the Great Mosque of Córdoba, built ca. 960 a.C. The type spread through Spain, and the north of Africa in the 10th to the 16th Centuries, and was used by Guarini and Vittone in the 17th and 18th Centuries in Italy. However, it was used only in a few buildings. Though the literature about the structural behaviour of ribbed Gothic vaults is extensive, so far no structural analysis of crossed arch domes has been made. The purpose of this work is, first to show the way to attack such an analysis within the frame of Modern Limit Analysis of Masonry Structures (Heyman 1995), and then to apply the approach to study the stability of the dome of the Capilla de Villaviciosa. The work may give some clues to art and architectural historians to understand better the origin and development of Islamic dome architecture.

The &-prolog system: Exploiting independent and-parallelism

The &-Prolog system, a practical implementation of a parallel execution niodel for Prolog exploiting strict and non-strict independent and-parallelism, is described. Both automatic and manual parallelization of programs is supported. This description includes a summary of the system's language and architecture, some details of its execution model (based on the RAP-WAM model), and data on its performance on sequential workstations and shared memory multiprocessors, which is compared to that of current Prolog systems. The results to date show significant speed advantages over state-of-the-art sequential systems.

Design and Validation of an Optimized MB-OFDM Ultra Wideband Transceiver System

Esta tesis está incluida dentro del campo del campo de Multiband Orthogonal Frequency Division Multiplexing Ultra Wideband (MB-OFDM UWB), el cual ha adquirido una gran importancia en las comunicaciones inalámbricas de alta tasa de datos en la última década. UWB surgió con el objetivo de satisfacer la creciente demanda de conexiones inalámbricas en interiores y de uso doméstico, con bajo coste y alta velocidad. La disponibilidad de un ancho de banda grande, el potencial para alta velocidad de transmisión, baja complejidad y bajo consumo de energía, unido al bajo coste de implementación, representa una oportunidad única para que UWB se convierta en una solución ampliamente utilizada en aplicaciones de Wireless Personal Area Network (WPAN). UWB está definido como cualquier transmisión que ocupa un ancho de banda de más de 20% de su frecuencia central, o más de 500 MHz. En 2002, la Comisión Federal de Comunicaciones (FCC) definió que el rango de frecuencias de transmisión de UWB legal es de 3.1 a 10.6 GHz, con una energía de transmisión de -41.3 dBm/Hz. Bajo las directrices de FCC, el uso de la tecnología UWB puede aportar una enorme capacidad en las comunicaciones de corto alcance. Considerando las ecuaciones de capacidad de Shannon, incrementar la capacidad del canal requiere un incremento lineal en el ancho de banda, mientras que un aumento similar de la capacidad de canal requiere un aumento exponencial en la energía de transmisión. En los últimos años, s diferentes desarrollos del UWB han sido extensamente estudiados en diferentes áreas, entre los cuales, el protocolo de comunicaciones inalámbricas MB-OFDM UWB está considerado como la mejor elección y ha sido adoptado como estándar ISO/IEC para los WPANs. Combinando la modulación OFDM y la transmisión de datos utilizando las técnicas de salto de frecuencia, el sistema MB-OFDM UWB es capaz de soportar tasas de datos con que pueden variar de los 55 a los 480 Mbps, alcanzando una distancia máxima de hasta 10 metros. Se esperara que la tecnología MB-OFDM tenga un consumo energético muy bajo copando un are muy reducida en silicio, proporcionando soluciones de bajo coste que satisfagan las demandas del mercado. Para cumplir con todas estas expectativas, el desarrollo y la investigación del MBOFDM UWB deben enfrentarse a varios retos, como son la sincronización de alta sensibilidad, las restricciones de baja complejidad, las estrictas limitaciones energéticas, la escalabilidad y la flexibilidad. Tales retos requieren un procesamiento digital de la señal de última generación, capaz de desarrollar sistemas que puedan aprovechar por completo las ventajas del espectro UWB y proporcionar futuras aplicaciones inalámbricas en interiores. Esta tesis se centra en la completa optimización de un sistema de transceptor de banda base MB-OFDM UWB digital, cuyo objetivo es investigar y diseñar un subsistema de comunicación inalámbrica para la aplicación de las Redes de Sensores Inalámbricas Visuales. La complejidad inherente de los procesadores FFT/IFFT y el sistema de sincronización así como la alta frecuencia de operación para todos los elementos de procesamiento, se convierten en el cuello de la botella para el diseño y la implementación del sistema de UWB digital en base de banda basado en MB-OFDM de baja energía. El objetivo del transceptor propuesto es conseguir baja energía y baja complejidad bajo la premisa de un alto rendimiento. Las optimizaciones están realizadas tanto a nivel algorítmico como a nivel arquitectural para todos los elementos del sistema. Una arquitectura hardware eficiente en consumo se propone en primer lugar para aquellos módulos correspondientes a núcleos de computación. Para el procesado de la Transformada Rápida de Fourier (FFT/IFFT), se propone un algoritmo mixed-radix, basado en una arquitectura con pipeline y se ha desarrollado un módulo de Decodificador de Viterbi (VD) equilibrado en coste-velocidad con el objetivo de reducir el consumo energético e incrementar la velocidad de procesamiento. También se ha implementado un correlador signo-bit simple basado en la sincronización del tiempo de símbolo es presentado. Este correlador es usado para detectar y sincronizar los paquetes de OFDM de forma robusta y precisa. Para el desarrollo de los subsitemas de procesamiento y realizar la integración del sistema completo se han empleado tecnologías de última generación. El dispositivo utilizado para el sistema propuesto es una FPGA Virtex 5 XC5VLX110T del fabricante Xilinx. La validación el propuesta para el sistema transceptor se ha implementado en dicha placa de FPGA. En este trabajo se presenta un algoritmo, y una arquitectura, diseñado con filosofía de co-diseño hardware/software para el desarrollo de sistemas de FPGA complejos. El objetivo principal de la estrategia propuesta es de encontrar una metodología eficiente para el diseño de un sistema de FPGA configurable optimizado con el empleo del mínimo esfuerzo posible en el sistema de procedimiento de verificación, por tanto acelerar el periodo de desarrollo del sistema. La metodología de co-diseño presentada tiene la ventaja de ser fácil de usar, contiene todos los pasos desde la propuesta del algoritmo hasta la verificación del hardware, y puede ser ampliamente extendida para casi todos los tipos de desarrollos de FPGAs. En este trabajo se ha desarrollado sólo el sistema de transceptor digital de banda base por lo que la comprobación de señales transmitidas a través del canal inalámbrico en los entornos reales de comunicación sigue requiriendo componentes RF y un front-end analógico. No obstante, utilizando la metodología de co-simulación hardware/software citada anteriormente, es posible comunicar el sistema de transmisor y el receptor digital utilizando los modelos de canales propuestos por IEEE 802.15.3a, implementados en MATLAB. Por tanto, simplemente ajustando las características de cada modelo de canal, por ejemplo, un incremento del retraso y de la frecuencia central, podemos estimar el comportamiento del sistema propuesto en diferentes escenarios y entornos. Las mayores contribuciones de esta tesis son: • Se ha propuesto un nuevo algoritmo 128-puntos base mixto FFT usando la arquitectura pipeline multi-ruta. Los complejos multiplicadores para cada etapa de procesamiento son diseñados usando la arquitectura modificada shiftadd. Los sistemas word length y twiddle word length son comparados y seleccionados basándose en la señal para cuantización del SQNR y el análisis de energías. • El desempeño del procesador IFFT es analizado bajo diferentes situaciones aritméticas de bloques de punto flotante (BFP) para el control de desbordamiento, por tanto, para encontrar la arquitectura perfecta del algoritmo IFFT basado en el procesador FFT propuesto. • Para el sistema de receptor MB-OFDM UWB se ha empleado una sincronización del tiempo innovadora, de baja complejidad y esquema de compensación, que consiste en funciones de Detector de Paquetes (PD) y Estimación del Offset del tiempo. Simplificando el cross-correlation y maximizar las funciones probables solo a sign-bit, la complejidad computacional se ve reducida significativamente. • Se ha propuesto un sistema de decodificadores Viterbi de 64 estados de decisión-débil usando velocidad base-4 de arquitectura suma-comparaselecciona. El algoritmo Two-pointer Even también es introducido en la unidad de rastreador de origen con el objetivo de conseguir la eficiencia en el hardware. • Se han integrado varias tecnologías de última generación en el completo sistema transceptor basebanda , con el objetivo de implementar un sistema de comunicación UWB altamente optimizado. • Un diseño de flujo mejorado es propuesto para el complejo sistema de implementación, el cual puede ser usado para diseños de Cadena de puertas de campo programable general (FPGA). El diseño mencionado no sólo reduce dramáticamente el tiempo para la verificación funcional, sino también provee un análisis automático como los errores del retraso del output para el sistema de hardware implementado. • Un ambiente de comunicación virtual es establecido para la validación del propuesto sistema de transceptores MB-OFDM. Este método es provisto para facilitar el uso y la conveniencia de analizar el sistema digital de basebanda sin parte frontera analógica bajo diferentes ambientes de comunicación. Esta tesis doctoral está organizada en seis capítulos. En el primer capítulo se encuentra una breve introducción al campo del UWB, tanto relacionado con el proyecto como la motivación del desarrollo del sistema de MB-OFDM. En el capítulo 2, se presenta la información general y los requisitos del protocolo de comunicación inalámbrica MBOFDM UWB. En el capítulo 3 se habla de la arquitectura del sistema de transceptor digital MB-OFDM de banda base . El diseño del algoritmo propuesto y la arquitectura para cada elemento del procesamiento está detallado en este capítulo. Los retos de diseño del sistema que involucra un compromiso de discusión entre la complejidad de diseño, el consumo de energía, el coste de hardware, el desempeño del sistema, y otros aspectos. En el capítulo 4, se ha descrito la co-diseñada metodología de hardware/software. Cada parte del flujo del diseño será detallado con algunos ejemplos que se ha hecho durante el desarrollo del sistema. Aprovechando esta estrategia de diseño, el procedimiento de comunicación virtual es llevado a cabo para probar y analizar la arquitectura del transceptor propuesto. Los resultados experimentales de la co-simulación y el informe sintético de la implementación del sistema FPGA son reflejados en el capítulo 5. Finalmente, en el capítulo 6 se incluye las conclusiones y los futuros proyectos, y también los resultados derivados de este proyecto de doctorado. ABSTRACT In recent years, the Wireless Visual Sensor Network (WVSN) has drawn great interest in wireless communication research area. They enable a wealth of new applications such as building security control, image sensing, and target localization. However, nowadays wireless communication protocols (ZigBee, Wi-Fi, and Bluetooth for example) cannot fully satisfy the demands of high data rate, low power consumption, short range, and high robustness requirements. New communication protocol is highly desired for such kind of applications. The Ultra Wideband (UWB) wireless communication protocol, which has increased in importance for high data rate wireless communication field, are emerging as an important topic for WVSN research. UWB has emerged as a technology that offers great promise to satisfy the growing demand for low-cost, high-speed digital wireless indoor and home networks. The large bandwidth available, the potential for high data rate transmission, and the potential for low complexity and low power consumption, along with low implementation cost, all present a unique opportunity for UWB to become a widely adopted radio solution for future Wireless Personal Area Network (WPAN) applications. UWB is defined as any transmission that occupies a bandwidth of more than 20% of its center frequency, or more than 500 MHz. In 2002, the Federal Communications Commission (FCC) has mandated that UWB radio transmission can legally operate in the range from 3.1 to 10.6 GHz at a transmitter power of －41.3 dBm/Hz. Under the FCC guidelines, the use of UWB technology can provide enormous capacity over short communication ranges. Considering Shannon’s capacity equations, increasing the channel capacity requires linear increasing in bandwidth, whereas similar channel capacity increases would require exponential increases in transmission power. In recent years, several different UWB developments has been widely studied in different area, among which, the MB-OFDM UWB wireless communication protocol is considered to be the leading choice and has recently been adopted in the ISO/IEC standard for WPANs. By combing the OFDM modulation and data transmission using frequency hopping techniques, the MB-OFDM UWB system is able to support various data rates, ranging from 55 to 480 Mbps, over distances up to 10 meters. The MB-OFDM technology is expected to consume very little power and silicon area, as well as provide low-cost solutions that can satisfy consumer market demands. To fulfill these expectations, MB-OFDM UWB research and development have to cope with several challenges, which consist of high-sensitivity synchronization, low- complexity constraints, strict power limitations, scalability, and flexibility. Such challenges require state-of-the-art digital signal processing expertise to develop systems that could fully take advantages of the UWB spectrum and support future indoor wireless applications. This thesis focuses on fully optimization for the MB-OFDM UWB digital baseband transceiver system, aiming at researching and designing a wireless communication subsystem for the Wireless Visual Sensor Networks (WVSNs) application. The inherent high complexity of the FFT/IFFT processor and synchronization system, and high operation frequency for all processing elements, becomes the bottleneck for low power MB-OFDM based UWB digital baseband system hardware design and implementation. The proposed transceiver system targets low power and low complexity under the premise of high performance. Optimizations are made at both algorithm and architecture level for each element of the transceiver system. The low-power hardwareefficient structures are firstly proposed for those core computation modules, i.e., the mixed-radix algorithm based pipelined architecture is proposed for the Fast Fourier Transform (FFT/IFFT) processor, and the cost-speed balanced Viterbi Decoder (VD) module is developed, in the aim of lowering the power consumption and increasing the processing speed. In addition, a low complexity sign-bit correlation based symbol timing synchronization scheme is presented so as to detect and synchronize the OFDM packets robustly and accurately. Moreover, several state-of-the-art technologies are used for developing other processing subsystems and an entire MB-OFDM digital baseband transceiver system is integrated. The target device for the proposed transceiver system is Xilinx Virtex 5 XC5VLX110T FPGA board. In order to validate the proposed transceiver system in the FPGA board, a unified algorithm-architecture-circuit hardware/software co-design environment for complex FPGA system development is presented in this work. The main objective of the proposed strategy is to find an efficient methodology for designing a configurable optimized FPGA system by using as few efforts as possible in system verification procedure, so as to speed up the system development period. The presented co-design methodology has the advantages of easy to use, covering all steps from algorithm proposal to hardware verification, and widely spread for almost all kinds of FPGA developments. Because only the digital baseband transceiver system is developed in this thesis, the validation of transmitting signals through wireless channel in real communication environments still requires the analog front-end and RF components. However, by using the aforementioned hardware/software co-simulation methodology, the transmitter and receiver digital baseband systems get the opportunity to communicate with each other through the channel models, which are proposed from the IEEE 802.15.3a research group, established in MATLAB. Thus, by simply adjust the characteristics of each channel model, e.g. mean excess delay and center frequency, we can estimate the transmission performance of the proposed transceiver system through different communication situations. The main contributions of this thesis are: • A novel mixed radix 128-point FFT algorithm by using multipath pipelined architecture is proposed. The complex multipliers for each processing stage are designed by using modified shift-add architectures. The system wordlength and twiddle word-length are compared and selected based on Signal to Quantization Noise Ratio (SQNR) and power analysis. • IFFT processor performance is analyzed under different Block Floating Point (BFP) arithmetic situations for overflow control, so as to find out the perfect architecture of IFFT algorithm based on the proposed FFT processor. • An innovative low complex timing synchronization and compensation scheme, which consists of Packet Detector (PD) and Timing Offset Estimation (TOE) functions, for MB-OFDM UWB receiver system is employed. By simplifying the cross-correlation and maximum likelihood functions to signbit only, the computational complexity is significantly reduced. • A 64 state soft-decision Viterbi Decoder system by using high speed radix-4 Add-Compare-Select architecture is proposed. Two-pointer Even algorithm is also introduced into the Trace Back unit in the aim of hardware-efficiency. • Several state-of-the-art technologies are integrated into the complete baseband transceiver system, in the aim of implementing a highly-optimized UWB communication system. • An improved design flow is proposed for complex system implementation which can be used for general Field-Programmable Gate Array (FPGA) designs. The design method not only dramatically reduces the time for functional verification, but also provides automatic analysis such as errors and output delays for the implemented hardware systems. • A virtual communication environment is established for validating the proposed MB-OFDM transceiver system. This methodology is proved to be easy for usage and convenient for analyzing the digital baseband system without analog frontend under different communication environments. This PhD thesis is organized in six chapters. In the chapter 1 a brief introduction to the UWB field, as well as the related work, is done, along with the motivation of MBOFDM system development. In the chapter 2, the general information and requirement of MB-OFDM UWB wireless communication protocol is presented. In the chapter 3, the architecture of the MB-OFDM digital baseband transceiver system is presented. The design of the proposed algorithm and architecture for each processing element is detailed in this chapter. Design challenges of such system involve trade-off discussions among design complexity, power consumption, hardware cost, system performance, and some other aspects. All these factors are analyzed and discussed. In the chapter 4, the hardware/software co-design methodology is proposed. Each step of this design flow will be detailed by taking some examples that we met during system development. Then, taking advantages of this design strategy, the Virtual Communication procedure is carried out so as to test and analyze the proposed transceiver architecture. Experimental results from the co-simulation and synthesis report of the implemented FPGA system are given in the chapter 5. The chapter 6 includes conclusions and future work, as well as the results derived from this PhD work.

Sobre la identidad de la ciudad. El estudio de la interacción audiovisual en las nuevas herramientas para el proyecto. El caso de Cuenca

Esta investigación se centra en el estudio de la dimensión audiovisual de la arquitectura, como aproximación intersensorial a la aprehensión e ideación del espacio. Poniendo en evidencia la complejidad de la relación hombre-medio, se plantea la necesidad de desarrollar nuevas metodologías y herramientas que tengan en cuenta dicha complejidad y que favorezcan el desarrollo del proyecto. Nos mueve en esta investigación la convicción de que los cambios rápidos y profundos que caracterizan nuestros tiempos en todos los ámbitos, social, económico, político… entrañan inevita-blemente nuevos modos de conocimiento y experimentación del espacio, y por tanto nuevos ejes de investigación. La creciente valoración, en todos los campos del conocimiento, de los aspectos subjetivos y sensoriales, el desarrollo de las tecnologías que ha cambiado completamente nuestras relaciones interpersonales y con el entorno, las nuevas capacidades de análisis, grabación y conservación y manipulación de datos y por ultimo, aunque no menos importante, la puesta a disposición democrá¬tica y global de todo el saber a través de Internet, imponen otra aproximación al hacer, concebir y vivir la arquitectura. Esta investigación se centra en un análisis crítico del estado de la cuestión, construyendo nue¬vas redes de relación entre disciplinas, que permitan plantear la dimensión audiovisual como un nuevo eje de investigación dentro de la arquitectura, poniendo en evidencia la necesidad de desa¬rrollar análisis de forma trasversal e interdisciplinar. Hemos prestado particular atención a la evolución de lo sonoro y su aproximación cualitativa a la arquitectura, mostrando como el sonido, con su capacidad de introducir el tiempo y los aspectos dinámicos (el movimiento, la presencia del cuerpo…), no es simplemente otro canal sensorial en la aprehensión del espacio, ya que su interacción con lo visual genera un espacio-tiempo indisociable, propio, característico de cada momento y lugar. A partir de este planteamiento se ha hecho una revisión metodológica dirigida a utilizar el reco¬rrido como herramienta de análisis, que permita estudiar la relación entre el espacio, la acción y la percepción audio-visual, cruzando para ello los datos correspondientes a la morfología del espacio, con los datos de la experiencia perceptiva individual y con los de los usos colectivos del espacio, utilizándose finalmente el video como un herramienta, no sólo de representación de lo real, sino también como instrumento de análisis, que permite tomar datos (grabaciones audio, video, obser¬vaciones…), aislarlos, estudiarlos, clasificarlos, ordenarlos, y finalmente, restituirlos mediante el montaje. Se ha realizado una primera experimentación “in situ” que ha servido para explorar la aplicación del método, planteando nuevas preguntas y abriendo líneas de análisis para ulteriores investigacio¬nes. ABSTRACT This research is focused on the study of the audiovisual dimension of architecture, as an in¬tersensorial approach to space apprehension and design. It is posed the necessity to develop new methodologies and tools that keep this complexity, as a contribution to the development of a project, by means of putting into evidence the sophistication of the relationship between man and media The research moves us to the conviction that the quick and relevant changes that confer a distinc-tion to these contemporary times all over the social, economic and political environments, involve, unavoidably, new ways of knowledge and experimentation on space, and therefore, new trends of research. The growing valuation of subjective and sensorial aspects all over the fields of the knowledge and the development of the technologies that have changed completely our interpersonal and environmental relationships, the new tools for analysis, recording, conservation and manipulation of data and, last but not least, the setting to democratic and global availability of the whole knowledge through Inter¬net, impose another approach to the making, conception and experience of architecture. This research deals with a critical analysis of the state–of- the-art of the matter, modelling new webs of relationship among disciplines that allow to outline the audiovisual dimension as a new focus of research on architecture, putting evidence into practice as it is necessary to develop any analysis in a transversal and interdisciplinary way. It is paid a special attention to the evolution of sound objects and their qualitative approach to ar¬chitecture, showing how sound, with its capacity to transmit time and dynamic aspects of things (movement, the presence of the body), it is not simply another sensorial channel in the apprehension of space, since its interaction with the visual thing generates an undetachable association of space and time, an specific one of every moment and place. Starting from this position a methodological revision has been made leading to use a walk as a tool for analysis that allows to study the relationship among the space, the action and the audio-visual perception, by means of crossing data corresponding to the morphology of space, with the data of a perceptive experience from the perspective of an individual observer and with those of the collective uses of the space, as video has been finally used as a tool, not only as a representation of the real thing, but also as a tool for analysis that allows to take isolated data (audio recordings, video, obser¬vations), to be studied, classified, and put into their appropriate place, and finally, to restore them by means of a multimedia set up. A first experimentation in situ has been carried out, being useful to explore a method of appli¬cation, outlining new questions and beginning with new ways of analysis for further research.

Luz industrial e imagen tecnificada: de Moholy Nagy al C.A.V.S. (Center for Advanced Visual Studies)

El desarrollo de la tecnología de la luz implicará la transformación de la vida social, cultural y económica. Tanto las consideraciones espaciales del Movimiento Moderno, como los efectos producidos por la segunda Guerra Mundial, tendrán efectos visibles en las nuevas configuraciones espaciales y en la relación simbiótica y recíproca que se dará entre ideología y tecnología. La transformación en la comprensión de la articulación espacial, asociada al desarrollo tecnológico, afectará al modo en que este espacio es experimentado y percibido. El espacio expositivo y el espacio escénico se convertirán en laboratorio práctico donde desarrollar y hacer comprensible todo el potencial ilusorio de la luz, la proyección y la imagen, como parámetros modificadores y dinamizadores del espacio arquitectónico. Esta experimentación espacial estará precedida por la investigación y creación conceptual en el mundo plástico, donde los nuevos medios mecánicos serán responsables de la construcción de una nueva mirada moderna mediatizada por los elementos técnicos. La experimentación óptica, a través de la fotografía, el cine, o el movimiento de la luz y su percepción, vinculada a nuevos modos de representación y comunicación, se convertirá en elemento fundamental en la configuración espacial. Este ámbito de experimentación se hará patente en la Escuela de la Bauhaus, de la mano de Gropius, Schlemmer o Moholy Nagy entre otros; tanto en reflexiones teóricas como en el desarrollo de proyectos expositivos, arquitectónicos o teatrales, que evolucionarán en base a la tecnología y la modificación de la relación con el espectador. El espacio expositivo y el espacio escénico se tomarán como oportunidad de investigación espacial y de análisis de los modos de percepción, convirtiéndose en lugares de experimentación básicos para el aprendizaje. El teatro se postula como punto de encuentro entre el arte y la técnica, cobrando especial importancia la intersección con otras disciplinas en la definición espacial. Las múltiples innovaciones técnicas ligadas a los nuevos fundamentos teatrales en la modificación de la relación con la escena, que se producen a principios del siglo XX, tendrán como consecuencia la transformación del espacio en un espacio dinámico, tanto física como perceptivamente, que dará lugar a nuevas concepciones espaciales, muchas de ellas utópicas. La luz, la proyección y la creación de ilusión en base a estímulos visuales y sonoros, aparecen como elementos proyectuales efímeros e inmateriales, que tendrán una gran incidencia en el espacio y su modo de ser experimentado. La implicación de la tecnología en el arte conllevará modificaciones en la visualización, así como en la configuración espacial de los espacios destinados a esta. Destacaremos como propuesta el Teatro Total de Walter Gropius, en cuyo desarrollo se recogen de algún modo las experiencias espaciales y las investigaciones desarrolladas sobre la estructura formal de la percepción realizadas por Moholy Nagy, además de los conceptos acerca del espacio escénico desarrollados en el taller de Teatro de la Bauhaus por Oskar Schlemmer. En el Teatro Total, Gropius incorporará su propia visión de cuestiones que pertenecen a la tradición de la arquitectura teatral y las innovaciones conceptuales que estaban teniendo lugar desde finales del s.XIX, tales como la participación activa del público o la superación entre escena y auditorio, estableciendo en el proyecto una nueva relación perceptual entre sala, espectáculo y espectador; aumentando la sensación de inmersión, a través del uso de la física, la óptica, y la acústica, creando una energía concéntrica capaz de extenderse en todas direcciones. El Teatro Total será uno de los primeros ejemplos en los que desde el punto de partida del proyecto, se conjuga la imagen como elemento comunicativo con la configuración espacial. Las nuevas configuraciones escénicas tendrán como premisa de desarrollo la capacidad de transformación tanto perceptiva, como física. En la segunda mitad del s.XX, la creación de centros de investigación como el CAVS (The Center for Advanced Visual Studies,1967), o el EAT (Experiments in Art and Technology, 1966), favorecerán la colaboración interdisciplinar entre arte y ciencia, implicando a empresas de carácter tecnológico, como Siemens, HP, IBM o Philips, facilitando soporte técnico y económico para el desarrollo de nuevos sistemas. Esta colaboración interdisciplinar dará lugar a una serie de intervenciones espaciales que tendrán su mayor visibilidad en algunas Exposiciones Universales. El resultado será, en la mayoría de los casos, la creación de espacios de carácter inmersivo, donde se establecerá una relación simbiótica entre espacio, imagen, sonido, y espectador. La colocación del espectador en el centro de la escena y la disposición dinámica de imagen y sonido, crearán una particular narrativa espacial no lineal, concebida para la experiencia. Desde las primeras proyecciones de cine a la pantalla múltiple de los Eames, las técnicas espaciales de difusión del sonido en Stockhausen, o los experimentos con el movimiento físico interactivo, la imagen, la luz en movimiento y el sonido, quedan inevitablemente convertidos en material arquitectónico. ABSTRACT. Light technology development would lead to a social, cultural and economic transformation. Both spatial consideration of “Modern Movement” and Second World War effects on technology, would have a visible aftereffect on spatial configuration and on the symbiotic and mutual relationship between ideology & technology. Comprehension adjustment on the articulation of space together with technology development, would impact on how space is perceived and felt. Exhibition space and scenic space would turn into a laboratory where developing and making comprehensive all illusory potential of light, projection and image. These new parameters would modify and revitalize the architectonic space. as modifying and revitalizing parameters of architectonic space. Spatial experimentation would be preceded by conceptual creation and investigation on the sculptural field, where new mechanic media would be responsible for a fresh and modern look influenced by technical elements. Optical experimentation, through photography, cinema or light movement and its perception, would turn into essential components for spatial arrangement linked to new ways of performance and communication. This experimentation sphere would be clear at The Bauhaus School, by the hand of Gropius, Schlemmer or Moholy Nag among others; in theoretical, theatrical or architectural performance’s projects, that would evolve based on technology and also based on the transformation of the relationship with the observer. Exhibition and perfor-mance areas would be taken as opportunities of spatial investigation and for the analysis of the different ways of perception, thus becoming key places for learning. Theater is postulated as a meeting point between art and technique, taking on a new significance at its intersection with other disciplines working with spatial definition too. The multiple innovation techniques linked to the new foundations for the theater regarding stage relation, would have as a consequence the regeneration of the space. Space would turn dynamic, both physically and perceptibly, bringing innovative spatial conceptions, many of them unrealistic. Light, projection and illusory creation based on sound and visual stimulus would appear as intangible and momentary design components, which would have a great impact on the space and on the way it is experienced. Implication of technology in art would bring changes on the observer as well as on the spatial configuration of the art spaces2. It would stand out as a proposal Walter Groupis Total Theater, whose development would include somehow the spatial experiments and studies about formal structure of perception accomplished by Moholy Nagy besides the concepts regarding stage space enhanced at the Bauhaus Theater Studio by Oskar Schlemmer. Within Total Theater, Groupis would incorporate his own view about traditional theatric architecture and conceptual innovations that were taking place since the end of the nineteenth century, such as active audience participation or the diffusing limits between scene and audience, establishing a new perception relationship between auditorium, performance and audience, improving the feeling of immersion through the use of physics, optics and acoustics, creating a concentric energy capable of spreading in all directions. Total Theater would be one of the first example in which, from the beginning of the Project, image is combined as a communicating element with the spatial configuration. As a premise of development, new stage arrangement would have the capacity of transformation, both perceptive and physically. During the second half or the twentieth century, the creation of investigation centers such as CAVS (Center for Advanced Visual Studies, 1967) or EAT (Experiments in Art and Technology, 1966), would help to the interdisciplinary collaboration between art and science, involving technology companies like Siemens, HP, IBM or Philips, providing technical and economic support to the development of new systems. This interdisciplinary collaboration would give room to a series of spatial interventions which would have visibility in some Universal Exhibitions. The result would be, in most cases, the creation of immersive character spaces, where a symbiotic relationship would be stablished between space, image, sound and audience. The new location of the audience in the middle of the display, together with the dynamic arrangement of sound and image would create a particular, no lineal narrative conceived to be experienced. Since the first cinema projections, the multiple screen of Eames, the spatial techniques for sound dissemination at Stockhausen or the interactive physical movement experimentation, image, motion light and sound would turn inevitably into architectural material.