Normal median near nerve potential

In routine studies of sensory nerve conduction, only fibers e7 µm in diameter are analyzed. The late components which originate from thinner fibers are not detected. This explains why a normal sensory action potential (SAP) may be recorded in patients with peripheral neuropathies and sensory loss. In the present study we investigated the late component of the median SAP with a near nerve needle electrode technique in 14 normal volunteers (7 men and 7 women), aged 34.5 ± 14.8 years. The stimulus consisted of rectangular pulses of 0.2-ms duration at a frequency of 1 Hz with an intensity at least 6 times greater than the threshold value for the main component. Five hundred to 2000 sweep averagings were performed. The duration of analysis was 40 or 50 ms and the wave analysis frequency was 200 (-6 dB/oct) to 3000 Hz (-12 dB/oct). We used an apparatus with a two-channel amplifier system, 200 MW or more of entry impedance and a noise level of 0.7 µVrms or less. The main component mean amplitude, conduction velocity and latency and the late component mean amplitude, conduction velocity and latency were respectively (mean ± SD): 26.5 ± 5.42 µV, 56.8 ± 5.42 m/s, 3.01 ± 0.31 ms, 0.12 ± 0.04 µV, 16.4 ± 2.95 m/s and 10.6 ± 2.48 ms. More sophisticated equipment has an internal noise of 0.6 µVrms. These data demonstrate that the technique can now be employed to study thin fiber neuropathies, like in leprosy, using commercial electromyographs, even in non-academic practices

A comparative analysis of preprocessing techniques of cardiac event series for the study of heart rhythm variability using simulated signals

In the present study, using noise-free simulated signals, we performed a comparative examination of several preprocessing techniques that are used to transform the cardiac event series in a regularly sampled time series, appropriate for spectral analysis of heart rhythm variability (HRV). First, a group of noise-free simulated point event series, which represents a time series of heartbeats, was generated by an integral pulse frequency modulation model. In order to evaluate the performance of the preprocessing methods, the differences between the spectra of the preprocessed simulated signals and the true spectrum (spectrum of the model input modulating signals) were surveyed by visual analysis and by contrasting merit indices. It is desired that estimated spectra match the true spectrum as close as possible, showing a minimum of harmonic components and other artifacts. The merit indices proposed to quantify these mismatches were the leakage rate, defined as a measure of leakage components (located outside some narrow windows centered at frequencies of model input modulating signals) with respect to the whole spectral components, and the numbers of leakage components with amplitudes greater than 1%, 5% and 10% of the total spectral components. Our data, obtained from a noise-free simulation, indicate that the utilization of heart rate values instead of heart period values in the derivation of signals representative of heart rhythm results in more accurate spectra. Furthermore, our data support the efficiency of the widely used preprocessing technique based on the convolution of inverse interval function values with a rectangular window, and suggest the preprocessing technique based on a cubic polynomial interpolation of inverse interval function values and succeeding spectral analysis as another efficient and fast method for the analysis of HRV signals

Liquid cooling solutions for rotating permanent magnet synchronous machines

In the design of electrical machines, efficiency improvements have become very important. However, there are at least two significant cases in which the compactness of electrical machines is critical and the tolerance of extremely high losses is valued: vehicle traction, where very high torque density is desired at least temporarily; and direct-drive wind turbine generators, whose mass should be acceptably low. As ever higher torque density and ever more compact electrical machines are developed for these purposes, thermal issues, i.e. avoidance of over-temperatures and damage in conditions of high heat losses, are becoming of utmost importance. The excessive temperatures of critical machine components, such as insulation and permanent magnets, easily cause failures of the whole electrical equipment. In electrical machines with excitation systems based on permanent magnets, special attention must be paid to the rotor temperature because of the temperature-sensitive properties of permanent magnets. The allowable temperature of NdFeB magnets is usually significantly less than 150 ˚C. The practical problem is that the part of the machine where the permanent magnets are located should stay cooler than the copper windings, which can easily tolerate temperatures of 155 ˚C or 180 ˚C. Therefore, new cooling solutions should be developed in order to cool permanent magnet electrical machines with high torque density and because of it with high concentrated losses in stators. In this doctoral dissertation, direct and indirect liquid cooling techniques for permanent magnet synchronous electrical machines (PMSM) with high torque density are presented and discussed. The aim of this research is to analyse thermal behaviours of the machines using the most applicable and accurate thermal analysis methods and to propose new, practical machine designs based on these analyses. The Computational Fluid Dynamics (CFD) thermal simulations of the heat transfer inside the machines and lumped parameter thermal network (LPTN) simulations both presented herein are used for the analyses. Detailed descriptions of the simulated thermal models are also presented. Most of the theoretical considerations and simulations have been verified via experimental measurements on a copper tooth-coil (motorette) and on various prototypes of electrical machines. The indirect liquid cooling systems of a 100 kW axial flux (AF) PMSM and a 110 kW radial flux (RF) PMSM are analysed here by means of simplified 3D CFD conjugate thermal models of the parts of both machines. In terms of results, a significant temperature drop of 40 ̊C in the stator winding and 28 ̊C in the rotor of the AF PMSM was achieved with the addition of highly thermally conductive materials into the machine: copper bars inserted in the teeth, and potting material around the end windings. In the RF PMSM, the potting material resulted in a temperature decrease of 6 ̊C in the stator winding, and in a decrease of 10 ̊C in the rotor embedded-permanentmagnets. Two types of unique direct liquid cooling systems for low power machines are analysed herein to demonstrate the effectiveness of the cooling systems in conditions of highly concentrated heat losses. LPTN analysis and CFD thermal analysis (the latter being particularly useful for unique design) were applied to simulate the temperature distribution within the machine models. Oil-immersion cooling provided good cooling capability for a 26.6 kW PMSM of a hybrid vehicle. A direct liquid cooling system for the copper winding with inner stainless steel tubes was designed for an 8 MW directdrive PM synchronous generator. The design principles of this cooling solution are described in detail in this thesis. The thermal analyses demonstrate that the stator winding and the rotor magnet temperatures are kept significantly below their critical temperatures with demineralized water flow. A comparison study of the coolant agents indicates that propylene glycol is more effective than ethylene glycol in arctic conditions.

Karbamatsepiinin Haihdutuskiteytys

Haihdutuskiteytyksessä haihdutusolosuhteilla on suuri vaikutus kiteiden muodostumiseen, joten toivottujen kidemuotojen saamiseksi prosessia on hallittava tarkasti. Kandidaatintyön tavoitteena oli tutkia puhtaiden liuottimien ja karbamatsepiiniliuosten haihtumisvuota eri olosuhteissa. Lisäksi tutkittiin kiteytysolosuhteiden vaikutusta karbamatsepiinikiteiden muodostumiseen ja rakenteeseen. Puhtaille liuottimille kokeet suoritettiin ilman virtausnopeudella 0,2 m/s lämpötiloissa 30 ºC, 40 ºC, 50 ºC ja 60 ºC, sekä ilman virtausnopeudella 0,3 m/s lämpötiloissa 40 ºC ja 50 ºC. Karbamatsepiiniliuoksille kokeet suoritettiin ilman virtausnopeudella 0,2 m/s lämpötiloissa 30 ºC ja 60 ºC sekä ilman virtausnopeudella 0,3 m/s lämpötiloissa 40 ºC ja 50 ºC. Haihdutuskiteytys suoritettiin suorakulmaisessa haihdutuskammiossa, jonka toisessa päässä oli tuulettimet virtausnopeuden säätämiseksi. Koehuoneessa vallitsi normaali ilmanpaine, ilman suhteellinen kosteus vaihteli välillä 50–65 % ja huoneen lämpötila välillä 21,2–24,1 ºC. Kuivatut kiteet analysoitiin optisella mikroskoopilla. Kaikista karbamatsepiinin vesiliuoksista kiteytyi dihydraatti-muotoa. Muutokset haihdutusolosuhteissa vaikuttivat selvästi haihtumis-voihin ja muodostuvien kiteiden rakenteeseen.

Double grade – rakenneputkien puristuskestävyys

Double grade S420MH/S355J2H – rakenneputki on Ruukin kylmämuovattujen rakenneputkien vakioteräslaji. Se voidaan mitoittaa joko lujuusluokan S355 tai S420 mukaisesti. Teräslajin S355 mukaisesti mitoitettaessa on suunnittelu yksinkertaista. Painonsäästöä ja pidennettyjä jännevälejä haluttaessa käytetään lujuusluokan S420 mukaista mitoitusta. Työn tavoitteena oli selvittää kylmämuovattujen teräsrakenneputkien todellinen puristuskestävyys. Eurocode 3:n mukaan kylmämuovatut teräsrakenneputket kuuluvat nurjahduskäyrälle c. Tutkimukseen valittiin viisi eri profiilia olevaa rakenneputkea, joiden poikkileikkausluokat olivat 1, 2, 3 ja 4. Käytettäessä rakenneputkia puristussauvoina, on teräksen käyttö tehokkainta poikkileikkausluokassa 3, lähellä poikkileikkausluokkaa 4. Rakenneputkista laskettiin muunnetun hoikkuuden arvoilla 0.1, 0.5, 1.0 ja 1.5 koesauvojen pituudet kaikille profiileille. Valmistettiin kolme samanlaista koesauvaa jokaisesta koosta ja puristuskokeita suoritettiin yhteensä 57 kappaletta. Koesauvojen todelliset pituudet, alkukäyryydet ja poikkileikkaukset mitattiin. Ainestodistuksista saatiin materiaalin todelliset lujuudet. Laskettiin Eurocode 3:n mukaisesti kestävyydet nurjahduskäyrille a, b ja c. Laskennallisia kestävyyksiä verrattiin puristuskokeiden tuloksiin. Puristuskokeiden tulosten perusteella voidaan b-käyrää pitää oikeana profiileille 100x100x3, 150,150x5 ja 200x200x6. Profiili 150x150x5 kuuluu poikkileikkausluokkaan 2. Profiilit 100x100x3 ja 200x200x6 kuuluvat poikkileikkausluokkaan 4. Profiili 50x50x2 kuuluu nurjahduskäyrälle c. Profiilin poikkileikkausluokka on 1 ja aiemmat tutkimukset tukevat nurjahduskäyrän c käyttöä. Profiilista 300x300x8.8 ei saatu testattua täyttä sarjaa sen suuren kapasiteetin rikottua testilaitteiston, mutta puristuskokeiden perusteella se kuuluu nurjahduskäyrälle b. Profiili kuuluu poikkileikkausluokkaan 4.

Fluvio-morphological processes of meander bends - Combining conventional field measurements, close-range remote sensing and computational modelling

Meandering rivers have been perceived to evolve rather similarly around the world independently of the location or size of the river. Despite the many consistent processes and characteristics they have also been noted to show complex and unique sets of fluviomorphological processes in which local factors play important role. These complex interactions of flow and morphology affect notably the development of the river. Comprehensive and fundamental field, flume and theoretically based studies of fluviomorphological processes in meandering rivers have been carried out especially during the latter part of the 20th century. However, as these studies have been carried out with traditional field measurements techniques their spatial and temporal resolution is not competitive to the level achievable today. The hypothesis of this study is that, by exploiting e increased spatial and temporal resolution of the data, achieved by combining conventional field measurements with a range of modern technologies, will provide new insights to the spatial patterns of the flow-sediment interaction in meandering streams, which have perceived to show notable variation in space and time. This thesis shows how the modern technologies can be combined to derive very high spatial and temporal resolution data on fluvio-morphological processes over meander bends. The flow structure over the bends is recorded in situ using acoustic Doppler current profiler (ADCP) and the spatial and temporal resolution of the flow data is enhanced using 2D and 3D CFD over various meander bends. The CFD are also exploited to simulate sediment transport. Multi-temporal terrestrial laser scanning (TLS), mobile laser scanning (MLS) and echo sounding data are used to measure the flow-based changes and formations over meander bends and to build the computational models. The spatial patterns of erosion and deposition over meander bends are analysed relative to the measured and modelled flow field and sediment transport. The results are compared with the classic theories of the processes in meander bends. Mainly, the results of this study follow well the existing theories and results of previous studies. However, some new insights regarding to the spatial and temporal patterns of the flow-sediment interaction in a natural sand-bed meander bend are provided. The results of this study show the advantages of the rapid and detailed measurements techniques and the achieved spatial and temporal resolution provided by CFD, unachievable with field measurements. The thesis also discusses the limitations which remain in the measurement and modelling methods and in understanding of fluvial geomorphology of meander bends. Further, the hydro- and morphodynamic models’ sensitivity to user-defined parameters is tested, and the modelling results are assessed against detailed field measurement. The study is implemented in the meandering sub-Arctic Pulmanki River in Finland. The river is unregulated and sand-bed and major morphological changes occur annually on the meander point bars, which are inundated only during the snow-melt-induced spring floods. The outcome of this study applies to sandbed meandering rivers in regions where normally one significant flood event occurs annually, such as Arctic areas with snow-melt induced spring floods, and where the point bars of the meander bends are inundated only during the flood events.

Modulation of hormone secretion by functional electrical stimulation of the intact and incompletely dysfunctional dog pancreas

The purpose of the present study was to modulate the secretion of insulin and glucagon in Beagle dogs by stimulation of nerves innervating the intact and partly dysfunctional pancreas. Three 33-electrode spiral cuffs were implanted on the vagus, splanchnic and pancreatic nerves in each of two animals. Partial dysfunction of the pancreas was induced with alloxan. The nerves were stimulated using rectangular, charge-balanced, biphasic, and constant current pulses (200 µs, 1 mA, 20 Hz, with a 100-µs delay between biphasic phases). Blood samples from the femoral artery were drawn before the experiment, at the beginning of stimulation, after 5 min of stimulation, and 5 min after the end of stimulation. Radioimmunoassay data showed that in the intact pancreas stimulation of the vagal nerve increased insulin (+99.2 µU/ml) and glucagon (+18.7 pg/ml) secretion and decreased C-peptide secretion (-0.15 ng/ml). Splanchnic nerve stimulation increased insulin (+1.7 µU/ml), C-peptide (+0.01 ng/ml), and glucagon (+50 pg/ml) secretion, whereas pancreatic nerve stimulation did not cause a marked change in any of the three hormones. In the partly dysfunctional pancreas, vagus nerve stimulation increased insulin (+15.5 µU/ml), glucagon (+11 pg/ml), and C-peptide (+0.03 ng/ml) secretion. Splanchnic nerve stimulation reduced insulin secretion (-2.5 µU/ml) and increased glucagon (+58.7 pg/ml) and C-peptide (+0.39 ng/ml) secretion, and pancreatic nerve stimulation increased insulin (+0.2 µU/ml), glucagon (+5.2 pg/ml), and C-peptide (+0.08 ng/ml) secretion. It was concluded that vagal nerve stimulation can significantly increase insulin secretion for a prolonged period of time in intact and in partly dysfunctional pancreas.

Harvesterin sahalaipan jatkotutkimus ja tuotteistaminen

Tämän diplomityön tavoitteena oli saavuttaa Joensuun CNC-Machining Oy:n aloittama harvesterinlaipan kehitystyö loppuun. Kehitystyön oli aloittanut vuonna 2012 Teemu Tuominen omalla opinnäytetyöllään, joka keskittyi suunnittelua ja valmistusta rajoittavien patenttien selvittämiseen sekä laipan valmistuksessa käytettyjen materiaalien selvittämiseen. Kirjallisuuskatsauksen ja puutuvien tietojen hankinnan jälkeen tarkasteluun otettiin aiemmin valmistettu prototyyppi sekä rikkoutuneita käytetyjä laippoja. Näistä laipoista tehtiin havaintoja esille nousevista ongelmakohdista, joiden perusteella tässä työssä suunnitelmaa päivitettiin ja asetettiin vaatimukset uudelle prototyypille. Kokonaisrakenteen suunnittelun jälkeen keskityttiin viimeistelemään osatoiminnallisuuksien yksityiskohdat. Suunnittelun tulosten perusteella valmistettiin laipasta prototyyppisarja, joista kahdella suoritettiin todellista käyttöä vastaava koeajo. Koeajon aikana ja jälkeen laippojen käyttäytymisestä ja suorituskyvystä tehtiin havaintoja. Valmistuksesta ja koeajosta saaduilla tiedoilla laippamallia kehitetään kohti markkinakelpoista tuotetta ja tuoteperhettä kasvatetaan eri mallisilla laipoilla.

Reconstruction of cranial bone defects with fiber-reinforced composite–bioactive glass implants

A cranial bone defect may result after an operative treatment of trauma, infection, vascular insult, or tumor. New biomaterials for cranial bone defect reconstructions are needed for example to mimic the biomechanical properties and structure of cranial bone. A novel glass fiber-reinforced composite implant with bioactive glass particulates (FRC–BG, fiber-reinforced composite–bioactive glass) has osteointegrative potential in a preclinical setting. The aim of the first and second study was to investigate the functionality of a FRC–BG implant in the reconstruction of cranial bone defects. During the years 2007–2014, a prospective clinical trial was conducted in two tertiary level academic institutions (Turku University Hospital and Oulu University Hospital) to evaluate the treatment outcome in 35 patients that underwent a FRC–BG cranioplasty. The treatment outcome was good both in adult and pediatric patients. A number of conventional complications related to cranioplasty were observed. In the third study, a retrospective outcome evaluation of 100 cranioplasty procedures performed in Turku University Hospital between years 2002–2012 was conducted. The experimental fourth study was conducted to test the load-bearing capacity and fracture behavior of FRC–BG implants under static loading. The interconnective bars in the implant structure markedly increased the load-bearing capacity of the implant. A loading test did not demonstrate any protrusions of glass fibers or fiber cut. The fracture type was buckling and delamination. In this study, a postoperative complication requiring a reoperation or removal of the cranioplasty material was observed in one out of five cranioplasty patients. The treatment outcomes of cranioplasty performed with different synthetic materials did not show significant difference when compared with autograft. The FRC–BG implant was demonstrated to be safe and biocompatible biomaterial for large cranial bone defect reconstructions in adult and pediatric patients.

Heat-transfer improvements in an axial-flux permanent-magnet synchronous machine

Axial-flux machines tend to have cooling difficulties since it is difficult to arrange continuous heat path between the stator stack and the frame. One important reason for this is that no shrink fitting of the stator is possible in an axial-flux machine. Using of liquid-cooled end shields does not alone solve this issue. Cooling of the rotor and the end windings may also be difficult at least in case of two-stator-single-rotor construction where air circulation in the rotor and in the end-winding areas may be difficult to arrange. If the rotor has significant losses air circulation via the rotor and behind the stator yokes should be arranged which, again, weakens the stator cooling. In this paper we study a novel way of using copper bars as extra heat transfer paths between the stator teeth and liquid cooling pools in the end shields. After this the end windings still suffer of low thermal conductivity and means for improving this by high-heat-conductance material was also studied. The design principle of each cooling system is presented in details. Thermal models based on Computational Fluid Dynamics (CFD) are used to analyse the temperature distribution in the machine. Measurement results are provided from different versions of the machine. The results show that significant improvements in the cooling can be gained by these steps.

Sellumassan varastosäiliön rakenneanalyysi

Tämä työ käsittelee valkaistun ja valkaisemattoman sellumassan varastosäiliön tärinää ja värähtelyä. Värähtelyn seurauksena säiliön seinämän jäykisterenkaan hitsausliitokseen on syntynyt särö. Työn tavoitteena on selvittää, mikä johtaa särön syntyyn ja miten kestäväm-piä varastosäiliöitä voidaan rakentaa materiaali-, valmistus- tai rakennemuutoksien avulla. Työ alkoi tutkimalla rakennemateriaalina olevan duplex-teräksen mikrorakenteen ominai-suuksia, sekä sen hitsattavuutta ja seostamista kirjallisuustutkimuksena. Kirjallisuustutki-musta jatkettiin selvittämällä mahdollisia vaurion syntymekanismeja seinämän särölle. Työssä analysoitiin myös tehtaalla mitattuja värähtelyarvoja. Lopuksi laskettiin FE-analyysillä tyhjän varastosäiliön ominaismuodot ja -taajuudet moodianalyysillä, sekä selvi-tettiin harmonisella analyysillä pinnankorkeuden vaihtelun vaikutus siirtymävasteeseen ja kriittisiin värähtelytaajuuksiin. Varastosäiliöön kohdistuvaa värähtelyä ei ole mahdollista poistaa kokonaan, mutta väräh-telyn aiheuttamia seurauksia kyetään rajaamaan useilla keinoilla. Toimenpiteinä voivat olla ainakin seinämän materiaalin paksuuden lisääminen, jäykisteripojen lisääminen ja kriittisten sellun pinnankorkeuksien välttäminen. Kriittiseksi pinnankorkeudeksi havaittiin 40–45 %:n täyttöaste ja turvalliseksi korkeudeksi 35–38 %:n täyttöaste. Varastosäiliölle kriittisen ominaistaajuuden katsotaan syntyvän taajuuksilla 3,3–3,8 Hz ja 5,8–6,4 Hz. Sellumassa putoaa varastosäiliöön noin 2 Hz taajuudella.

Le Réformiste (Paris)

Périodicité : Hebd. puis bimens

Concrete Forms

Forms and reinforcing steel bars used in the walls of the Aquatic Centre.

Percy Carruthers Band fonds, 1857-2005, n.d. (non-inclusive)

Percy Carruthers Band was born on November 27, 1892 in Toronto, Ontario to Charles Walter Band, a grain merchant and Jessie Camp Shaw Band. He graduated from Upper Canada College and became a broker. He worked at the Dominion Bank and then at Maple Leaf Milling Company. He was stationed at Port Colborne for a while. Before leaving for the front, he was with Bankers Bond Company of Toronto and is also listed as working with the firm of Bailey, Wood and Cross. Lieutenant Band received a Certificate of Military Qualifications on Dec. 24th, 1914. He received his Certificate of Military Instruction on Nov. 30, 1915. He received these certificates while with the 48th Regiment (Highlanders). He enlisted in 1914 and went overseas in August of 1915 as an officer in the 35th Battalion. By August 26, 1915, he is listed as being with the 23rd Reserve Battalion. A year later, in August of 1916 Lieutenant Band arrived in France and was posted to the 2nd Battalion – “The Second Iron”. In 1916, Band was the victim of shell shock received during a charge. He was wounded in April of 1917 at Vimy Ridge yet he remained on duty. At this time he received a gunshot wound to his right jaw. He earned a promotion to Captain on September 16th, 1917. He was wounded again in November of 1917 at Passchendaele where he suffered a gunshot wound to the ear. For his courage and determination Percy Band received the Military Cross on February 18, 1918. He led his company under difficult circumstances even though he was wounded. He was awarded a bar to the Military Cross for gallantry during a successful attack on two villages on December 2nd, 1918. During this attack he led his company against enemy machine guns. It is said that he displayed exceptional leadership qualities and skill during this time. On the 30th of August in 1918, he made a daring reconnaissance to the front under heavy fire in an attack on Upton Wood. He was also commended on his gallantry during attacks on Cagnicourt and the Canal du Nord in September of 1918. He was awarded the second bar to the Military Cross on February 1, 1919. The award of the Croix de Guerre was conferred on Captain Percy Carruthers Band by the President of the French Republic on December 15th, 1918 for distinguished service rendered during the course of the campaign. His general demobilization took place on April 25, 1919. Percy Band married Margaret Julia Woodruff on November 25, 1919, and they had three children: Charles Woodruff Band (1921), Margaret Elizabeth Band (1924) and Robert DeVeaux Woodruff Band (1927). After the war, Mr. Band was a manager at Geo. Weston Bread and Cakes Limited, St. Catharines. Percy Band was also an avid collector. His collections included antique toys and art. He died suddenly on May 19, 1961. The Toronto Telegram published this about him: “Captain Percy Carruthers Band, M.C. with two Bars, Croix de Guerre with Palm – was an officer whose buoyant spirit and gallantry mirrored the vibrant soul of the Battalion. Blythe of heart, yet endowed with a fine sense of responsibility, he gave inspired leadership of No. 3 Company.”

De l'organisation au déroulement d'événements rave à Montréal : étude des mécanismes de régulation sociale

Les raves sont des événements festifs dédiés à la musique techno et à la danse qui se distinguent des autres lieux de rassemblement tels que les bars et les discothèques notamment par le fait qu’ils se déroulent toute la nuit dans un lieu aménagé pour l’occasion et qu’il n’y a généralement pas de vente d’alcool. La consommation de drogues de synthèse telles que l’ecstasy et les speeds y est toutefois largement répandue. La tenue de ces rassemblements pose une série de problèmes du point de vue des autorités policières, tels que la présence de trafiquants de drogues ainsi que la sécurité des lieux où se déroulent les raves. Dans le contexte particulier de ces événements, les pratiques de contrôle social sont soumises à un certain nombre d’ambiguïtés. Le but général de l’étude est de permettre une compréhension de la façon dont se déterminent et s’appliquent les règles qui visent à encadrer la tenue de ce type de rassemblements. Trois objectifs spécifiques sont poursuivis, soit 1) de comprendre comment on a tenté de réguler ce type d’événements à Montréal, 2) de comprendre comment les différents acteurs responsables de l’organisation et du bon déroulement des événements établissent une série de règles, aussi bien formelles qu’informelles, et négocient leur application dans le cadre de leur pratique, et 3) de comprendre comment ces acteurs identifient certaines situations comme constituant un problème et éventuellement, y réagissent. La principale méthode de recueil des données a consisté à réaliser des entretiens semi-dirigés avec des promoteurs d’événements rave, des agents de sécurité ainsi que d’autres personnes impliquées dans le milieu telles que policier, pompier, artistes de la scène rave et intervenants. L’observation participante lors d’événements rave fut utilisée comme méthode complémentaire. L’étude démontre comment le service de police s’est vu confronté avec les raves à un vide juridique et comment l’encadrement de ce type d’événements s’est plutôt exercé par le service de prévention des incendies. Les autorités ont également tenté d’encadrer le phénomène par des modifications à certaines règlementations, dont celles sur les permis d’alcool. L’étude démontre également de quelle manière et en fonction de quoi les différents acteurs du milieu négocient les règles en cours d’action dans un contexte où la frontière entre le licite et l’illicite est floue.