866 resultados para random number generation
Resumo:
Temporal dynamics of Raman fibre lasers tend to have very complex nature, owing to great cavity lengths and high nonlinearity, being stochastic on short time scales and quasi-continuous on longer time scales. Generally fibre laser intensity dynamics is represented by one-dimensional time-series, which in case of quasi-continuous wave generation in Raman fibre lasers gives little insight into the processes underlying the operation of a laser. New methods of analysis and data representation could help to uncover the underlying physical processes, understand the dynamics or improve the performance of the system. Using intrinsic periodicity of laser radiation, one dimensional intensity time series of a Raman fibre laser was analysed over fast and slow variation time. This allowed to experimentally observe various spatio-temporal regimes of generation, such as laminar, turbulent, partial mode-lock, as well as transitions between them and identify the mechanisms responsible for the transitions. Great cavity length and high nonlinearity also make it difficult to achieve stable high repetition rate mode-locking in Raman fibre lasers. Using Faraday parametric instability in extremely simple linear cavity experimental configuration, a very high order harmonic mode-locking was achieved in ò.ò kmlong Raman fibre laser. The maximum achieved pulse repetition rate was 12 GHz, with 7.3 ps long Gaussian shaped pulses. There is a new type of random lasers – random distributed feedback Raman fibre laser, which temporal properties cannot be controlled by conventionalmode-locking or Q-switch techniques and mechanisms. By adjusting the pump configuration, a very stable pulsed operation of random distributed feedback Raman fibre laser was achieved. Pulse duration varied in the range from 50 to 200 μs depending on the pump power and the cavity length. Pulse repetition rate scaling on the parameters of the system was experimentally identified.
Resumo:
The rise in diversity and numbers of U.S. immigrants since 1965 has spawned a number of studies about the education of these immigrants and their children. Most of this research finds that school-age immigrants arriving in the last 20 years have the highest drop-out rates, lowest test scores, and are less likely than their native born peers to go to college. This dissertation examines the experiences of Nicaraguan immigrant youth living in Miami and the factors that make some of these adolescents feel positive about education, while others have negative attitudes about education. The method for this study combined structured and unstructured interviews, participant observation, focus groups, and data collected from a larger data set to understand the academic orientation of 25 Nicaraguan youths over a 4-year period. One of the independent variables is length of time in the United States. During the time of my initial contact with the subjects, 6 had been living in the United States for less than 3 years, 14 had been living in the United States between 6 and 12 years, and 6 had been living in the in the United States most or all of their lives (either they were born in the United States or had resided here for over 12 years). ^ Results are based on the students' particular experiences, which influence the dependent variable, academic orientation. Besides length of time, the independent variables also include ethnic self-identity, perceived discrimination, social capital in Miami, and peer influence. The study finds that those who are very recent arrivals have a “dual frame of reference,” that is, they directly compare their educational opportunities here in the United States, with their prior, often less favorable, situation in their homeland. Many of those who were born in Nicaragua, but have been residing in Miami most of their lives, have a less favorable view of education based on a higher degree of perceived discrimination. However, those who are second generation Nicaraguans deliberately take advantage of the strength inherent in their co-ethnic community unique to Miami. Recognition of this ethnic community prompts them to perceive education as worthwhile. ^
Resumo:
Immigrants from Jamaica represent the largest number of migrants to the United States from the English speaking Caribbean. Research indicates that of all Caribbean immigrants they are most likely to retain the ethnic identity of their home country for the longest period of time. This dissertation explored the nature of ethnic identity and sought to determine its impact upon the additional variables of self-esteem and academic factors. A secondary analysis was carried out using data collected in the Spring of 1992 by Portes and Rumbaut on the children of immigrants attending the eighth and ninth grades in local schools in San Diego and southern Florida. A sample of 151 second-generation Jamaican immigrants was selected from the data set. ^ Six hypotheses yielded mixed results. Both parents who have a Jamaican ethnic identity present in the household are the best predictor Jamaican youth who retain a Jamaican ethnic identity. It was expected that ethnic identity would be a predictor of positive academic factors. The study showed that ethnic identity was not associated with one of the academic factors which were examined: help given with homework. ^ Neither family economic status nor parents' level of education played a significant role in the retention of Jamaican identity. Other findings were that there was no mean difference in the self-esteem scores of respondents who had similar ethnic identities to their parents and those who did not. There was also no difference found in the academic factors of either group. The study also showed that there was a small correlation between parent-child conflict and self-esteem. Specifically, the study found that the higher the conflict between youth and their parents, the lower the self-esteem of the youth. Finally it found that time lived in the U.S. was the best predictor of a higher GPA and it was also related to lower self-esteem. ^ Surprisingly, the study found that the relationship between ethnic identity and SES was the opposite of what was expected in that it found that SES was higher when there was no Jamaican identity. ^
Resumo:
Next-generation sequencing (NGS) technologies have enabled us to determine phytoplankton community compositions at high resolution. However, few studies have adopted this approach to assess the responses of natural phytoplankton communities to environmental change. Here, we report the impact of different CO2 levels on spring diatoms in the Oyashio region of the western North Pacific as estimated by NGS of the diatom-specific rbcL gene (DNA), which encodes the large subunit of RubisCO. We also examined the abundance and composition of rbcL transcripts (cDNA) in diatoms to assess their physiological responses to changing CO2 levels. A short-term (3-day) incubation experiment was carried out on-deck using surface Oyashio waters under different pCO2 levels (180, 350, 750, and 1000 µatm) in May 2011. During the incubation, the transcript abundance of the diatom-specific rbcL gene decreased with an increase in seawater pCO2 levels. These results suggest that CO2 fixation capacity of diatoms decreased rapidly under elevated CO2 levels. In the high CO2 treatments (750 and 1000 µatm), diversity of diatom-specific rbcL gene and its transcripts decreased relative to the control treatment (350µatm), as well as contributions of Chaetocerataceae, Thalassiosiraceae, and Fragilariaceae to the total population, but the contributions of Bacillariaceae increased. In the low CO2 treatment, contributions of Bacillariaceae also increased together with other eukaryotes. These suggest that changes in CO2 levels can alter the community composition of spring diatoms in the Oyashio region. Overall, the NGS technology provided us a deeper understanding of the response of diatoms to changes in CO2 levels in terms of their community composition, diversity, and photosynthetic physiology.
Resumo:
Funding This work was supported by the Ministry of Education , Nigeria for financial support through the TETFUND scholarship 55 scheme; CSIR [grant number 03(1264)/12/EMR-II].
Resumo:
This thesis details the top-down fabrication of nanostructures on Si and Ge substrates by electron beam lithography (EBL). Various polymeric resist materials were used to create nanopatterns by EBL and Chapter 1 discusses the development characteristics of these resists. Chapter 3 describes the processing parameters, resolution and topographical and structural changes of a new EBL resist known as ‘SML’. A comparison between SML and the standard resists PMMA and ZEP520A was undertaken to determine the suitability of SML as an EBL resist. It was established that SML is capable of high-resolution patterning and showed good pattern transfer capabilities. Germanium is a desirable material for use in microelectronic applications due to a number of superior qualities over silicon. EBL patterning of Ge with high-resolution hydrogen silsesquioxane (HSQ) resist is however difficult due to the presence of native surface oxides. Thus, to combat this problem a new technique for passivating Ge surfaces prior to EBL processes is detailed in Chapter 4. The surface passivation was carried out using simple acids like citric acid and acetic acid. The acids were gentle on the surface and enabled the formation of high-resolution arrays of Ge nanowires using HSQ resist. Chapter 5 details the directed self-assembly (DSA) of block copolymers (BCPs) on EBL patterned Si and, for the very first time, Ge surfaces. DSA of BCPs on template substrates is a promising technology for high volume and cost effective nanofabrication. The BCP employed for this study was poly (styrene-b-ethylene oxide) and the substrates were pre-defined by HSQ templates produced by EBL. The DSA technique resulted into pattern rectification (ordering in BCP) and in pattern multiplication within smaller areas.
Resumo:
Increasingly in power systems, there is a trend towards the sharing of reserves and integration of markets over wide areas in order to enable increased penetration of renewable sources in interconnected power systems. In this paper, a number of simple PI and gain based Model Predictive Control algorithms are proposed for Automatic Generation Control in AC areas connected to Multi-Terminal Direct Current grids. The paper discusses how this approach improves the sharing of secondary reserves and could assist in achieving EU energy targets for 2030 and beyond.
Resumo:
Wind generation in highly interconnected power networks creates local and centralised stability issues based on their proximity to conventional synchronous generators and load centres. This paper examines the large disturbance stability issues (i.e. rotor angle and voltage stability) in power networks with geographically distributed wind resources in the context of a number of dispatch scenarios based on profiles of historical wind generation for a real power network. Stability issues have been analysed using novel stability indices developed from dynamic characteristics of wind generation. The results of this study show that localised stability issues worsen when significant penetration of both conventional and wind generation is present due to their non-complementary characteristics. In contrast, network stability improves when either high penetration of wind and synchronous generation is present in the network. Therefore, network regions can be clustered into two distinct stability groups (i.e. superior stability and inferior stability regions). Network stability improves when a voltage control strategy is implemented at wind farms, however both stability clusters remain unchanged irrespective of change in the control strategy. Moreover, this study has shown that the enhanced fault ride-through (FRT) strategy for wind farms can improve both voltage and rotor angle stability locally, but only a marginal improvement is evident in neighbouring regions.
Resumo:
This paper presents a thorough experimental study on key generation principles, i.e. temporal variation, channel reciprocity, and spatial decorrelation, via a testbed constructed by using wireless open-access research platform (WARP). It is the first comprehensive study through (i) carrying out a number of experiments in different multipath environments, including an anechoic chamber, a reverberation chamber and an indoor office environment, which represents little, rich, and moderate multipath, respectively; (ii) considering static, object moving, and mobile scenarios in these environments, which represents different levels of channel dynamicity; (iii) studying two most popular channel parameters, i.e., channel state information and received signal strength. Through results collected from over a hundred tests, this paper offers insights to the design of a secure and efficient key generation system. We show that multipath is essential and beneficial for key generation as it increases the channel randomness. We also find that the movement of users/objects can help introduce temporal variation/randomness and help users reach an agreement on the keys. This paper complements existing research by experiments constructed by a new hardware platform.
Resumo:
Forced convection heat transfer in a micro-channel filled with a porous material saturated with rarefied gas with internal heat generation is studied analytically in this work. The study is performed by analysing the boundary conditions for constant wall heat flux under local thermal non-equilibrium (LTNE) conditions. Invoking the velocity slip and temperature jump, the thermal behaviour of the porous-fluid system is studied by considering thermally and hydrodynamically fully-developed conditions. The flow inside the porous material is modelled by the Darcy–Brinkman equation. Exact solutions are obtained for both the fluid and solid temperature distributions for two primary approaches models A and B using constant wall heat flux boundary conditions. The temperature distributions and Nusselt numbers for models A and B are compared, and the limiting cases resulting in the convergence or divergence of the two models are also discussed. The effects of pertinent parameters such as fluid to solid effective thermal conductivity ratio, Biot number, Darcy number, velocity slip and temperature jump coefficients, and fluid and solid internal heat generations are also discussed. The results indicate that the Nusselt number decreases with the increase of thermal conductivity ratio for both models. This contrasts results from previous studies which for model A reported that the Nusselt number increases with the increase of thermal conductivity ratio. The Biot number and thermal conductivity ratio are found to have substantial effects on the role of temperature jump coefficient in controlling the Nusselt number for models A and B. The Nusselt numbers calculated using model A change drastically with the variation of solid internal heat generation. In contrast, the Nusselt numbers obtained for model B show a weak dependency on the variation of internal heat generation. The velocity slip coefficient has no noticeable effect on the Nusselt numbers for both models. The difference between the Nusselt numbers calculated using the two models decreases with an increase of the temperature jump coefficient.
Resumo:
In Germany the upscaling algorithm is currently the standard approach for evaluating the PV power produced in a region. This method involves spatially interpolating the normalized power of a set of reference PV plants to estimate the power production by another set of unknown plants. As little information on the performances of this method could be found in the literature, the first goal of this thesis is to conduct an analysis of the uncertainty associated to this method. It was found that this method can lead to large errors when the set of reference plants has different characteristics or weather conditions than the set of unknown plants and when the set of reference plants is small. Based on these preliminary findings, an alternative method is proposed for calculating the aggregate power production of a set of PV plants. A probabilistic approach has been chosen by which a power production is calculated at each PV plant from corresponding weather data. The probabilistic approach consists of evaluating the power for each frequently occurring value of the parameters and estimating the most probable value by averaging these power values weighted by their frequency of occurrence. Most frequent parameter sets (e.g. module azimuth and tilt angle) and their frequency of occurrence have been assessed on the basis of a statistical analysis of parameters of approx. 35 000 PV plants. It has been found that the plant parameters are statistically dependent on the size and location of the PV plants. Accordingly, separate statistical values have been assessed for 14 classes of nominal capacity and 95 regions in Germany (two-digit zip-code areas). The performances of the upscaling and probabilistic approaches have been compared on the basis of 15 min power measurements from 715 PV plants provided by the German distribution system operator LEW Verteilnetz. It was found that the error of the probabilistic method is smaller than that of the upscaling method when the number of reference plants is sufficiently large (>100 reference plants in the case study considered in this chapter). When the number of reference plants is limited (<50 reference plants for the considered case study), it was found that the proposed approach provides a noticeable gain in accuracy with respect to the upscaling method.
Resumo:
Thesis (Ph.D.)--University of Washington, 2016-06
Resumo:
The non-standard decoding of the CUG codon in Candida cylindracea raises a number of questions about the evolutionary process of this organism and other species Candida clade for which the codon is ambiguous. In order to find some answers we studied the transcriptome of C. cylindracea, comparing its behavior with that of Saccharomyces cerevisiae (standard decoder) and Candida albicans (ambiguous decoder). The transcriptome characterization was performed using RNA-seq. This approach has several advantages over microarrays and its application is booming. TopHat and Cufflinks were the software used to build the protocol that allowed for gene quantification. About 95% of the reads were mapped on the genome. 3693 genes were analyzed, of which 1338 had a non-standard start codon (TTG/CTG) and the percentage of expressed genes was 99.4%. Most genes have intermediate levels of expression, some have little or no expression and a minority is highly expressed. The distribution profile of the CUG between the three species is different, but it can be significantly associated to gene expression levels: genes with fewer CUGs are the most highly expressed. However, CUG content is not related to the conservation level: more and less conserved genes have, on average, an equal number of CUGs. The most conserved genes are the most expressed. The lipase genes corroborate the results obtained for most genes of C. cylindracea since they are very rich in CUGs and nothing conserved. The reduced amount of CUG codons that was observed in highly expressed genes may be due, possibly, to an insufficient number of tRNA genes to cope with more CUGs without compromising translational efficiency. From the enrichment analysis, it was confirmed that the most conserved genes are associated with basic functions such as translation, pathogenesis and metabolism. From this set, genes with more or less CUGs seem to have different functions. The key issues on the evolutionary phenomenon remain unclear. However, the results are consistent with previous observations and shows a variety of conclusions that in future analyzes should be taken into consideration, since it was the first time that such a study was conducted.
Resumo:
Even though a large amount of evidence would suggest that PP2A serine/threonine protein phosphatase acts as a tumour suppressor the genomics data to support this claim is limited. We fit a sparse binary Markov random field with individual sample's total mutational frequency as an additional covariate to model the dependencies between the mutations occurring in the PP2A encoding genes. We utilize the data from recent large scale cancer genomics studies, where the whole genome from a human tumour biopsy has been analysed. Our results show a complex network of interactions between the occurrence of mutations in our twenty examined genes. According to our analysis the mutations occurring in the genes PPP2R1A, PPP2R3A, and PPP2R2B are identified as the key mutations. These genes form the core of the network of conditional dependency between the mutations in the investigated twenty genes. Additionally, we note that the mutations occurring in PPP2R4 seem to be more influential in samples with higher number of total mutations. The mutations occurring in the set of genes suggested by our results has been shown to contribute to the transformation of human cells. We conclude that our evidence further supports the claim that PP2A acts as a tumour suppressor and restoring PP2A activity is an appealing therapeutic strategy.