Costs and Benefits of a Shared Digital Long-Term Preservation System

Paper presented at the 40th Annual Conference of LIBER (Ligue des Bibliothèques Européennes de Recherche - Association of European Research Libraries) on July 1st, 2011; with the slides used at the presentation.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Prediction of free-stall occupancy rate in dairycattle barns through fuzzy sets

The goal of this study was to develop a fuzzy model to predict the occupancy rate of free-stalls facilities of dairy cattle, aiding to optimize the design of projects. The following input variables were defined for the development of the fuzzy system: dry bulb temperature (Tdb, °C), wet bulb temperature (Twb, °C) and black globe temperature (Tbg, °C). Based on the input variables, the fuzzy system predicts the occupancy rate (OR, %) of dairy cattle in free-stall barns. For the model validation, data collecting were conducted on the facilities of the Intensive System of Milk Production (SIPL), in the Dairy Cattle National Research Center (CNPGL) of Embrapa. The OR values, estimated by the fuzzy system, presented values of average standard deviation of 3.93%, indicating low rate of errors in the simulation. Simulated and measured results were statistically equal (P>0.05, t Test). After validating the proposed model, the average percentage of correct answers for the simulated data was 89.7%. Therefore, the fuzzy system developed for the occupancy rate prediction of free-stalls facilities for dairy cattle allowed a realistic prediction of stalls occupancy rate, allowing the planning and design of free-stall barns.

Development of racemization catalysts for dynamic kinetic resolution

Preparation of optically active compounds is of high importance in modern medicinal chemistry. Despite recent advances in the field of asymmetric synthesis, resolution of racemates still remains the most utilized way for preparation of single enantiomers in industrial scale due to its cost-efficiency and simplicity. Enzymatic kinetic resolution (KR) of racemates is a classical method for separation of enantiomers. One of its drawbacks is the limitation of target enantiomer yield to 50%. Dynamic Kinetic Resolution (DKR) allows to reach yields up to 100% by in situ racemization of the less reactive enantiomer. In the first part of this thesis, a number of half-sandwich ruthenium complexes were prepared and evaluated as catalysts for racemization of optically active secondary alcohols. A leading catalyst, Bn5CpRu(CO)2Cl, was identified. The catalyst discovered was extensively characterized by its application for DKR of a broad range of secondary alcohols in a wide range of reaction loadings (1 mmol – 1 mol). Cost-efficient chromatography-free procedure for preparation of this catalyst was developed. Further, detailed kinetic and mechanistic studies of the racemization reactions were performed. Comparison of racemization rates in the presence of Bn5CpRu(CO)2Cl and Ph5CpRu(CO)2Cl catalysts reveals that the performance of the catalytic system can be adjusted by matching of the electronic properties of the catalysts and the substrates. Moreover, dependence of the rate-limiting step from the electronic properties of the reagents was observed. Important conclusions about reaction mechanism were made. Finally, an alternative approach to DKR of amines based on space separated vessels was addressed. This procedure allows the combination of thermolabile enzyme with racemization catalysts active only at high temperatures.

AMB system for high-speed motors using automatic commissioning

The general trend towards increasing e ciency and energy density drives the industry to high-speed technologies. Active Magnetic Bearings (AMBs) are one of the technologies that allow contactless support of a rotating body. Theoretically, there are no limitations on the rotational speed. The absence of friction, low maintenance cost, micrometer precision, and programmable sti ness have made AMBs a viable choice for highdemanding applications. Along with the advances in power electronics, such as signi cantly improved reliability and cost, AMB systems have gained a wide adoption in the industry. The AMB system is a complex, open-loop unstable system with multiple inputs and outputs. For normal operation, such a system requires a feedback control. To meet the high demands for performance and robustness, model-based control techniques should be applied. These techniques require an accurate plant model description and uncertainty estimations. The advanced control methods require more e ort at the commissioning stage. In this work, a methodology is developed for an automatic commissioning of a subcritical, rigid gas blower machine. The commissioning process includes open-loop tuning of separate parts such as sensors and actuators. The next step is to apply a system identi cation procedure to obtain a model for the controller synthesis. Finally, a robust model-based controller is synthesized and experimentally evaluated in the full operating range of the system. The commissioning procedure is developed by applying only the system components available and a priori knowledge without any additional hardware. Thus, the work provides an intelligent system with a self-diagnostics feature and an automatic commissioning.

Design of RFID-system for industrial after-sale service

RFID-tekniikka on radiotaajuudella toimivaa etätunnistusta, jossa hyödynnetään RFID-tunnisteiksi kutsuttuja tageja, sekä RFID-lukijoita. RFID-tekniikan käyttökohteet ovat erittäin laajat. Tässä kandidaatintyössä tutkitaan RFID-tekniikan hyödyntämismahdollisuuksia teollisuuden huoltopalvelusuhteessa. Työ keskittyy huollettavien laitteiden etätunnistamiseen mobiileja RFID-lukijoita hyödyntäen. Laitteiden tiedot noudetaan olemassa olevasta tietokannasta web-käyttöliittymän kautta. Koska laitteet koostuvat pääosin metallista, joudutaan tunnistetyyppien valintaa pohtimaan tarkasti. Metallipinnat sekä nesteet vaikuttavat erittäin negatiivisesti useiden tunnisteiden lukuetäisyyteen. Työssä keskitytään vaadittavan järjestelmän suunnittelemiseen aikaisempia tutkimuksia hyödyntäen, mutta itse järjestelmän toteutus ei kuulu tähän kandidaatintyöhön. Lopussa järjestelmän alustava suunnitelma esitellään.

Substitution-Newton-Raphson method applied to the modeling of a vapour compression refrigeration system using different representations of the thermodynamic properties of R-134a

This paper gives a detailed presentation of the Substitution-Newton-Raphson method, suitable for large sparse non-linear systems. It combines the Successive Substitution method and the Newton-Raphson method in such way as to take the best advantages of both, keeping the convergence features of the Newton-Raphson with the low requirements of memory and time of the Successive Substitution schemes. The large system is solved employing few effective variables, using the greatest possible part of the model equations in substitution fashion to fix the remaining variables, but maintaining the convergence characteristics of the Newton-Raphson. The methodology is exemplified through a simple algebraic system, and applied to a simple thermodynamic, mechanical and heat transfer modeling of a single-stage vapor compression refrigeration system. Three distinct approaches for reproducing the thermodynamic properties of the refrigerant R-134a are compared: the linear interpolation from tabulated data, the use of polynomial fitted curves and the use of functions derived from the Helmholtz free energy.

Growth and nutrient concentration in coffee root system under weed species competition

The effects of competition of six weed species on growth, nutrient concentration and nutrient content of coffee plant root system under greenhouse conditions were evaluated. Thirty days after coffee seedling transplantation into 12 L pots with soil level area of 6.5 dm². Weeds were transplanted or sowed in these pots, at densities of 0, 1, 2, 3, 4 and 5 plants per pot. The duration of competition (or weedy periods) from weed transplantation or emergence until plant harvesting, at the weed preflowering stage, were (in days): 77 (Bidens pilosa), 180 (Commelina diffusa), 82 (Leonurus sibiricus), 68 (Nicandra physaloides), 148 (Richardia brasiliensis) and 133 (Sida rhombifolia). Dry matter of coffee plants was linearly reduced with increasing B. pilosa and S. rhombifolia density, with pronounced effect of B. pilosa. C. diffusa was the only weed species whose increasing density in the pots did not diminish crop root dry matter. L. sibiricus, N. physaloides and R. brasiliensis reduced root dry matter of coffee plants by 75, 52 and 47%, respectively, as compared to the weed-free treatment, regardless of weed density. Under competition, even though weed species showed lower macronutrient concentration in the roots (except for P), they accumulated 4.2 (N), 12.3 (P), 4.3 (K), 5.5 (Ca), 7.6 (Mg) and 4.4 (S) times more nutrients in the roots than the coffee plants. Crop and weed nutrient concentration, as well as competition degrees greatly varied depending on both weed species and densities.

Eucalyptus growth in silvopastoral system under different crown dia meters

The aim of this study was to evaluate the effect of different crown diameters on the early growth of eucalyptus intercropped with Brachiaria decumbens in a silvopastoral system. The experiment was conducted in a B. decumbens established pasture, where hybrid eucalyptus urograndis (clone GG100) was planted, spaced 8 x 3 m. A randomized block design was used, with six replicates. Treatments consisted of five crown diameters (0.0, 1.0, 1.5, 2.0, and 3.0 m) surrounding the eucalyptus plants. Five weeding hoes were performed throughout the experiment, according to the different crown diameters, aiming to maintain the eucalyptus plants free from B. decumbens interference. At 90, 180, 270, and 360 DAP, the height and the diameter of the eucalyptus plants were evaluated, and at 360 DAP, surface biomass and leaf area were evaluated. At 90 DAP, it was verified that the non-weeded plants had lower growth, compared to those submitted to crowns. Crown diameters of 2.51 and 2.64 m allowed greater growth in height and diameter at ground level of eucalyptus plants, respectively, in all periods evaluated. Biomass production and leaf area per plant at 360 DAP were also influenced by the different crown diameters. It was concluded that crown diameter around 2 meters provided favorable conditions for early growth of eucalyptus and less involvement in the area occupied by forage.

Weed management boosts yield in fine rice under system of rice intensification

The system of rice intensification has emerged as a promising rice production package but weed infestation could lead to incomplete benefits from the system. A two-year field study was performed to determine an appropriate method of weed management in SRI. Weed management treatments were manual hoeing 20, 40 and 60 days after transplanting (DAT), hoeing with rotary hoe at 20, 40 and 60 DAT, hoeing with rotary hoe at 20 DAT + spray with sorghum and sunflower water extracts at 15 L ha-1 40 DAT, manual hoeing 20 DAT + spray with sorghum and sunflower water extracts, both in equal amount, at 15 L ha-1 40 DAT, orthosulfamuron at 145 g a.i. ha-1 7 DAT, weedy check and weed free. Manual hoeing at 20, 40 and 60 DAT was the treatment that exhibited the maximum kernel yield i.e. 5.34 and 4.99 t ha-1., which was 8.4 and 7.2% higher than orthosulfamuron and 61.0 and 64.9% higher than weedy check, during both years of study, respectively. The highest weed suppression was also achieved by manual hoeing at 20, 40 and 60 DAT with weed control efficiency of 87.89 and 82.32% during 2010 and 2011, respectively. Manual hoeing at 20, 40 and 60 DAT is an eco-friendly, non-chemical weed control method to increase kernel yield of fine rice under SRI.

Wild onion (Asphodelus tenuifolius) competition in rainfed chickpea-chickpea cropping system

Chickpea yield potential is limited by weed competition in typical chickpea growing areas of Pakistan where zero tillage crop grown on moisture conserved from rains received during the months of September and August. The objective of this work was to evaluate the growth and yield characteristics of chickpea grown in coexistence with increasing densities of wild onion (Asphodelus tenuifolius). The experiment was comprised of six density levels viz. zero, 20, 40, 80, 160 and 320 plants m-2 of A. tenuifolius. A decrease in chickpea primary and secondary branches per plant, pods per plant, seeds per pod, 100-seed weight and seed yield was observed due to more accumulation of dry matter per increasing densities of A. tenuifolius. The increase in A. tenuifolius density accelerated chickpea yield losses and reached the maximum values of 28, 35, 42, 50, 58 and 96% at 20, 40, 80, 160 and 320 A. tenuifolius plants m-2, respectively. The yield loss estimation model showed that chickpea losses with infinite A. tenuifolius density were 60%. Yield reduction could be predicted by 2.52% with increase of one A. tenuifolius plant m-2. It is concluded that A. tenuifolius has a strong influence on chickpea seed yield and showed a linear response at the range of densities studied.

Painted Into a Corner by Communities and Collections? Free Yourself with Metadata

Poster at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Are there evidences of a complex mimicry system among Asclepias curassavica (Apocynaceae), Epidendrum fulgens (Orchidaceae), and Lantana camara (Verbenaceae) in Southern Brazil?

The goal of this paper was to test the presence of mimicry in Asclepias curassavica L., Epidendrum fulgens Brong., and Lantana camara L. The study was carried out at the Parque Estadual de Itapeva, RS, southern Brazil, from 2004 to 2006. Flowering period of each of the three species was followed up; focal observations of butterflies visiting flowers, from fixed point and during random walks were carried out. We also estimated the frequency of pollinaria removal in the orchid, as well as its mode of reproduction. All these variables were important for testing the mimicry hypothesis. Despite some temporal coincidences in the flowering period of two plants in the system, there was no statistical association among the three plants as to flowering period. Twenty-nine species of butterflies, as potential pollinators, were recorded, particularly Agraulis vanillae maculosa, Dryas iulia alcionea, Urbanus simplicius, Tegosa claudina, and Heliconius erato phyllis, which were the more frequent visitors of the three plants. There was association between the number of visits to L. camara and E. fulgens, based on Pearson correlation (r = 0.4603; n = 19; P = 0.0473). Pollinaria removal of E. fulgens was low, as measured by the percentage of removal (range: 0 - 10%). The analysis of the mode of reproduction of this orchid showed its pollinator-dependence, since no fruits were formed by spontaneous self-pollination. In contrast, the percentage of fruit set that resulted from geitonogamy and xenogamy was, in average, 86%. The results here shown are not conclusive as to the occurrence of a mimicry system among the three plants.

Ca2+ dependence of gluconeogenesis stimulation by glucagon at different cytosolic NAD+-NADH redox potentials

The influence of Ca2+ on hepatic gluconeogenesis was measured in the isolated perfused rat liver at different cytosolic NAD+-NADH potentials. Lactate and pyruvate were the gluconeogenic substrates and the cytosolic NAD+-NADH potentials were changed by varying the lactate to pyruvate ratios from 0.01 to 100. The following results were obtained: a) gluconeogenesis from lactate plus pyruvate was not affected by Ca2+-free perfusion (no Ca2+ in the perfusion fluid combined with previous depletion of the intracellular pools); gluconeogenesis was also poorly dependent on the lactate to pyruvate ratios in the range of 0.1 to 100; only for a ratio equal to 0.01 was a significantly smaller gluconeogenic activity observed in comparison to the other ratios. b) In the presence of Ca2+, the increase in oxygen uptake caused by the infusion of lactate plus pyruvate at a ratio equal to 10 was the most pronounced one; in Ca2+-free perfusion the increase in oxygen uptake caused by lactate plus pyruvate infusion tended to be higher for all lactate to pyruvate ratios; the most pronounced difference was observed for a lactate/pyruvate ratio equal to 1. c) In the presence of Ca2+ the effects of glucagon on gluconeogenesis showed a positive correlation with the lactate to pyruvate ratios; for a ratio equal to 0.01 no stimulation occurred, but in the 0.1 to 100 range stimulation increased progressively, producing a clear parabolic dependence between the effects of glucagon and the lactate to pyruvate ratio. d) In the absence of Ca2+ the relationship between the changes caused by glucagon in gluconeogenesis and the lactate to pyruvate ratio was substantially changed; the dependence curve was no longer parabolic but sigmoidal in shape with a plateau beginning at a lactate/pyruvate ratio equal to 1; there was inhibition at the lactate to pyruvate ratios of 0.01 and 0.1 and a constant stimulation starting with a ratio equal to 1; for the lactate to pyruvate ratios of 10 and 100, stimulation caused by glucagon was much smaller than that found when Ca2+ was present. e) The effects of glucagon on oxygen uptake in the presence of Ca2+ showed a parabolic relationship with the lactate to pyruvate ratios which was closely similar to that found in the case of gluconeogenesis; the only difference was that inhibition rather than stimulation of oxygen uptake was observed for a lactate to pyruvate ratio equal to 0.01; progressive stimulation was observed in the 0.1 to 100 range. f) In the absence of Ca2+ the effects of glucagon on oxygen uptake were different; the dependence curve was sigmoidal at the onset, with a well-defined maximum at a lactate to pyruvate ratio equal to 1; this maximum was followed by a steady decline at higher ratios; at the ratios of 0.01 and 0.1 inhibition took place; oxygen uptake stimulation caused by glucagon was generally lower in the absence of Ca2+ except when the lactate to pyruvate ratio was equal to 1. The results of the present study demonstrate that stimulation of gluconeogenesis by glucagon depends on Ca2+. However, Ca2+ is only effective in helping gluconeogenesis stimulation by glucagon at highly negative redox potentials of the cytosolic NAD+-NADH system. The triple interdependence of glucagon-Ca2+-NAD+-NADH redox potential reveals highly complex interrelations that can only be partially understood at the present stage of knowledge