PCDD/F Emissions from Light-Duty Diesel Vehicles Operated under Highway Conditions and a Diesel-Engine Based Power Generator

PCDD/F emissions from three light-duty diesel vehicles–two vans and a passenger car–have been measured in on-road conditions. We propose a new methodology for small vehicles: a sample of exhaust gas is collected by means of equipment based on United States Environmental Protection Agency (U.S. EPA) method 23A for stationary stack emissions. The concentrations of O2, CO, CO2, NO, NO2 and SO2 have also been measured. Six tests were carried out at 90-100 km/h on a route 100 km long. Two additional tests were done during the first 10 minutes and the following 60 minutes of the run to assess the effect of the engine temperature on PCDD/F emissions. The emission factors obtained for the vans varied from 1800 to 8400 pg I-TEQ/Nm3 for a 2004 model year van and 490-580 pg I-TEQ/Nm3 for a 2006 model year van. Regarding the passenger car, one run was done in the presence of a catalyst and another without, obtaining emission factors (330-880 pg I-TEQ/Nm3) comparable to those of the modern van. Two other tests were carried out on a power generator leading to emission factors ranging from 31 to 78 pg I-TEQ/Nm3. All the results are discussed and compared with literature.

Abatement of hydrocarbons by acid ZSM-5 and BETA zeolites under cold-start conditions

Simulated cold-start tests have been carried out to evaluate the performance of H-ZSM-5 and H-BETA zeolites as hydrocarbon traps under simulated gasoline car exhaust gases, paying special attention to the effect of water on their behaviour. It is concluded that the hydrothermal treatment of the zeolites in the acidic form contributes to the better performance of these materials as hydrocarbon traps since the stabilization of the zeolites takes place. Moreover, the decrease of the surface acidity of the zeolites results in an increase of the Si/Al ratio, which contributes to the decrease of the water affinity for adsorption sites. Thus, the competition with hydrocarbon molecules in the exhaust for the adsorption sites is reduced which increases their trap efficiency. The stabilized H-ZSM-5 is the zeolite that showed the best performance with a propene offset temperature of 240 °C, which should be high enough for the three-way catalyst to carry out its role as catalytic converter.

CuH-ZSM-5 as Hydrocarbon Trap under Cold Start Conditions

Cold start tests are carried out to evaluate the performance of copper-exchanged zeolites as hydrocarbon traps under simulated gasoline car exhaust gases, paying special attention to the role of copper in the performance of these zeolites. It is concluded that the partial substitution of the protons in the parent H-ZSM-5 zeolite is highly beneficial for hydrocarbon trapping due to the formation of selective adsorption sites with specific affinity for the different exhaust components. However, it is also observed that uncontrolled exchanging process conditions could lead to the presence of CuO nanoparticles in the zeolite surface, which seem to block the pore structure of the zeolite, decreasing the hydrocarbon trap efficiency. Among all the zeolites studied, the results point out that a CuH-ZSM-5 with a partial substitution of extra-framework protons by copper cations and without any detectable surface CuO nanoparticles is the zeolite that showed the best performance under simulated cold start conditions due to both the high stability and the hydrocarbon retaining capacity of this sample during the consecutive cycles.

Optimizing the performance of catalytic traps for hydrocarbon abatement during the cold-start of a gasoline engine

A key target to reduce current hydrocarbon emissions from vehicular exhaust is to improve their abatement under cold-start conditions. Herein, we demonstrate the potential of factorial analysis to design a highly efficient catalytic trap. The impact of the synthesis conditions on the preparation of copper-loaded ZSM-5 is clearly revealed by XRD, N2 sorption, FTIR, NH3-TPD, SEM and TEM. A high concentration of copper nitrate precursor in the synthesis improves the removal of hydrocarbons, providing both strong adsorption sites for hydrocarbon retention at low temperature and copper oxide nanoparticles for full hydrocarbon catalytic combustion at high temperature. The use of copper acetate precursor leads to a more homogeneous dispersion of copper oxide nanoparticles also providing enough catalytic sites for the total oxidation of hydrocarbons released from the adsorption sites, although lower copper loadings are achieved. Thus, synthesis conditions leading to high copper loadings jointly with highly dispersed copper oxide nanoparticles would result in an exceptional catalytic trap able to reach superior hydrocarbon abatement under highly demanding operational conditions.

Benefici del long route EGR sulla riduzione dei consumi: studio di fattibilità su motore diesel automobilistico

L'EGR (Exhaust Gas Recirculation) è una tecnica comunemente sfruttata per la riduzione delle emissioni. In questo studio sono stati investigati i benefici, in termini di fuel economy, prodotti dall'aggiunta di un circuito EGR long route su un motore diesel per applicazioni automobilistiche dotato di sistema short route. L'indagine è stata svolta su di un modello motore su software GT-Power, adeguatamente calibrato e validato sui dati da piano quotato. Simulazioni sono state svolte al fine di valutare gli effetti del solo LP-EGR sul motore, per poi considerare un funzionamento combinato dai due sistemi di ricircolo (dual loop). Le maggiori portate che per il sistema long route interessano la turbina determinano un incremento nelle contropressioni. Ciò ha portato a considerare la possibilità di modificare il sistema turbo. Il layout originario comprendeva una turbina a geometria fissa (FGT), a cui ne sono stati affiancati due ulteriori con turbina a geometria variabile (VGT). I risultati sono stati analizzati vincolando la produzione di inquinanti ai valori registrati nei punti di calibrazione relativi al layout originale del motore. Effettivo risparmio di combustibile non è stato riscontrato nell'allestimento con turbina FGT a causa delle elevate contropressioni, mentre con turbine VGT è stata registrata una effettiva fuel economy grazie al sistema LP-EGR senza alcun deterioramento nelle emissioni di NOx e PM. I benefici riscontrati con il LP-EGR sono da attribure ad un incremento del rendimento indicato dovuto alla riduzione delle perdite per scambio termico a seguito di una minore temperatura caratterizzante i gas ricircolati.

(Table 1) Air-earth current density investigated during Atlantic Expedition 1973 of METEOR

One main point of our atmospheric-electric measurements over the Atlantic Ocean 1973 was the investigation of the air-earth current density above the sea. In addition to direct measurements at the water surface with a floating net, we calculated the air-earth current density from the electric field and the air conductivity measured simultaneously on board of the ship and during particular ascents in the free atmosphere. During all five ascents the air-earth current density did not change with altitude. For pure maritime air-conditions, the mean air-earth current density was found to be 2.9 pA/m**2. The mean hourly air-earth current density over the Atlantic shows nearly the same 24-hour pattern as measured by Cobb (1977) at the South Pole at the same time. When dust-loaden air masses of African origin reached the ship as well as under continental influence the mean air-earth current density was reduced to 2.1 pA/m**2. The global 24-hour pattern was modified by this continental influences. Finally, it is shown that the values of the air conductivity measured on board R. V. "Meteor" during our earlier expeditions have been influenced by the exhaust of the ship and must therefore be corrected. With this correction, our new mean values of the air-earth current density over the Atlantic are 2.6 pA/m**2 in 1965 and 2.0 pA/m**2 in 1969. From all measurements, the global air-earth current is estimated to be about 1250 A.

Truck noise IV-G. Field test results on a heavy duty, diesel truck having reduced noise emissions. Seventh report.

Transportation Department, Office of Noise Abatement, Washington, D.C.

Proceedings of the third Conference on the Climatic Impact Assessment Program, February 26-March 1, 1974 /

Includes bibliographical references and author index.

Truck noise IV-A: project summary - the reduction of noise levels on the International Harvester quieted truck. Final report.

Transportation Department, Office of Noise Abatement, Washington, D.C.

Evaluation of technology for control of arsenic emissions at the Campbell Red Lake Gold Smelter /

Mode of access: Internet.

Evaluation of benefits to the federal highway program provided by regulation of vehicle noise emissions.

Mode of access: Internet.

Truck noise XI. Evaluation and reduction of heavy-duty truck noise. Final report.

Transportation Department, Office of Noise Abatement, Washington, D.C.

Noise abatement techniques for construction equipment. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Evaluation of air cleaning and monitoring equipment used in recirculation systems /

Contract No. 210-78-0011.

Issues concerning the light-duty diesel /

"UC-20e & 96."