Development of a system measuring adhesion forces in powder collectives

Fine powders commonly have poor flowability and dispersibility due to interparticle adhesion that leads to formation of agglomerates. Knowing about adhesion in particle collectives is indispensable to gain a deeper fundamental understanding of particle behavior in powders. Especially in pharmaceutical industry a control of adhesion forces in powders is mandatory to improve the performance of inhalation products. Typically the size of inhalable particles is in the range of 1 - 5 µm. In this thesis, a new method was developed to measure adhesion forces of particles as an alternative to the established colloidal probe and centrifuge technique, which are both experimentally demanding, time consuming and of limited practical applicability. The new method is based on detachment of individual particles from a surface due to their inertia. The required acceleration in the order of 500 000 g is provided by a Hopkinson bar shock excitation system and measured via laser vibrometry. Particle detachment events are detected on-line by optical video microscopy. Subsequent automated data evaluation allows obtaining a statistical distribution of particle adhesion forces. To validate the new method, adhesion forces for ensembles of single polystyrene and silica microspheres on a polystyrene coated steel surface were measured under ambient conditions. It was possible to investigate more than 150 individual particles in one experiment and obtain adhesion values of particles in a diameter range of 3 - 13 µm. This enables a statistical evaluation while measuring effort and time are considerably lower compared to the established techniques. Measured adhesion forces of smaller particles agreed well with values from colloidal probe measurements and theoretical predictions. However, for the larger particles a stronger increase of adhesion with diameter was observed. This discrepancy might be induced by surface roughness and heterogeneity that influence small and large particles differently. By measuring adhesion forces of corrugated dextran particles with sizes down to 2 µm it was demonstrated that the Hopkinson bar method can be used to characterize more complex sample systems as well. Thus, the new device will be applicable to study a broad variety of different particle-surface combinations on a routine basis, including strongly cohesive powders like pharmaceutical drugs for inhalation.

Bone marrow-derived cells in palatal wound healing

OBJECTIVE: Myofibroblasts are responsible for contraction and scarring after cleft palate repair. This leads to growth disturbances in the upper jaw. We hypothesized that cells from the bone marrow are recruited to palatal wounds and differentiate into myofibroblasts. METHODS: We transplanted bone marrow from green fluorescent protein (GFP)-transgenic rats into lethally irradiated wild-type rats. After recovery, experimental wounds were made in the palatal mucoperiosteum, and harvested 2 weeks later. GFP-expressing cells were identified using immunostaining. Myofibroblasts, activated fibroblasts, endothelial cells, and myeloid cells were quantified with specific markers. RESULTS: After transplantation, 89 ± 8.9% of mononuclear cells in the blood expressed the GFP and about 50% of adherent cells in the bone marrow. Tissue obtained during initial wounding contained only minor numbers of GFP-positive cells, like adjacent control tissue. Following wound healing, 8.1 ± 5.1% of all cells in the wound area were positive, and 5.0 ± 4.0% of the myofibroblasts, which was significantly higher than in adjacent tissue. Similar percentages were found for activated fibroblasts and endothelial cells, but for myeloid cells it was considerably higher (22 ± 9%). CONCLUSIONS: Bone marrow-derived cells contribute to palatal wound healing, but are not the main source of myofibroblasts. In small wounds, the local precursor cells are probably sufficient to replenish the defect.

Material properties of common suture materials in orthopaedic surgery

Suture materials in orthopaedic surgery are used for closure of wounds, repair of fascia, muscles, tendons, ligaments, joint capsules, and cerclage or tension band of certain fractures. The purpose of this study was to compare the biomechanical properties of eleven commonly used sutures in orthopaedic surgery. Three types of braided non-absorbable and one type of braided absorbable suture material with different calibers (n=77) underwent biomechanical testing for maximum load to failure, strain, and stiffness. All samples were tied by one surgeon with a single SMC (Seoul Medical Center) knot and three square knots. The maximum load to failure and strain were highest for #5 FiberWire and lowest for #0 Ethibond Excel (p<0.001). The stiffness was highest for #5 FiberWire and lowest for #2-0 Vicryl (p<0.001). In all samples, the failure of the suture material occurred at the knot There was no slippage of the knot in any of the samples tested. This data will assist the orthopaedic surgeon in selection and application of appropriate suture materials and calibers to specific tasks.

A case of homicidal intraoral gunshot and review of the literature

Determination of the manner of death in case of intraoral firearm wounds can be a challenge, especially if the circumstances of the incident are unclear and crime scene investigation is inadequate. It is a well-known fact that the mouth is one of the selected sites for suicide with firearms. Homicidal shooting through the mouth is said to be rare, but does occur, and can be mistaken for a suicide. For discrimination between suicide and homicide in cases of intraoral firearm wounds, some useful points are the site of entry wound, the direction of the internal bullet path, the range of fire and the circumstances of death. We demonstrate these points in a case of a homicidal gunshot to the mouth assessed by both classical autopsy and post-mortem CT (PMCT).

Suicidal knife wound to the heart: challenges in reconstructing wound channels with post mortem CT and CT-angiography

We present a case of an individual who stabbed himself through the heart with a large knife. Post mortem computed tomography (CT) and CT-angiography were used to assess the stab channel and to reconstruct the sequence of events. After penetrating injuries to the chest, both the intra-thoracic organs and the injury causing instrument may shift (e.g. from pnemothorax) and render forensic reconstructions more challenging. This case report illustrates the potentials and the pitfalls of CT for the reconstruction of penetrating injures to the chest.

[Homicide by bow and arrow]

Since the invention of firearms, arrow wounds represent a rarity in the daily routine of forensic pathologists. In the present paper, we describe a homicide by a broadhead arrow shot from a compound bow in a domestic environment. Based on this homicide, we discuss the characteristics of the lesion caused by broadhead arrows and field-tip arrows. We look critically at the free saleability of this equipment mostly used for sport shooting in Germany.

Getting in touch-3D printing in Forensic Imaging

With the increasing use of medical imaging in forensics, as well as the technological advances in rapid prototyping, we suggest combining these techniques to generate displays of forensic findings. We used computed tomography (CT), CT angiography, magnetic resonance imaging (MRI) and surface scanning with photogrammetry in conjunction with segmentation techniques to generate 3D polygon meshes. Based on these data sets, a 3D printer created colored models of the anatomical structures. Using this technique, we could create models of bone fractures, vessels, cardiac infarctions, ruptured organs as well as bitemark wounds. The final models are anatomically accurate, fully colored representations of bones, vessels and soft tissue, and they demonstrate radiologically visible pathologies. The models are more easily understood by laypersons than volume rendering or 2D reconstructions. Therefore, they are suitable for presentations in courtrooms and for educational purposes.

The adhesion modulating properties of tenascin-w

Tenascins are extracellular matrix glycoproteins associated with cell motility, proliferation and differentiation. Tenascin-C inhibits cell spreading by binding to fibronectin; tenascin-R and tenascin-X also have anti-adhesive properties in vitro. Here we have studied the adhesion modulating properties of the most recently characterized tenascin, tenascin-W. C2C12 cells, a murine myoblast cell line, will form broad lamellipodia with stress fibers and focal adhesion complexes after culture on fibronectin. In contrast, C2C12 cells cultured on tenascin-W fail to spread and form stress fibers or focal adhesion complexes, and instead acquire a multipolar shape with short, actin-tipped pseudopodia. The same stellate morphology is observed when C2C12 cells are cultured on a mixture of fibronectin and tenascin-W, or on fibronectin in the presence of soluble tenascin-W. Tenascin-W combined with fibronectin also inhibits the spreading of mouse embryo fibroblasts when compared with cells cultured on fibronectin alone. The similarity between the adhesion modulating effects of tenascin-W and tenascin-C in vitro led us to study the possibility of tenascin-W compensating for tenascin-C in tenascin-C knockout mice, especially during epidermal wound healing. Dermal fibroblasts harvested from a tenascin-C knockout mouse express tenascin-W, but dermal fibroblasts taken from a wild type mouse do not. However, there is no upregulation of tenascin-W in the dermis of tenascin-C knockout mice, or in the granulation tissue of skin wounds in tenascin-C knockout animals. Similarly, tenascin-X is not upregulated in early wound granulation tissue in the tenascin-C knockout mice. Thus, tenascin-W is able to inhibit cell spreading in vitro and it is upregulated in dermal fibroblasts taken from the tenascin-C knockout mouse, but neither it nor tenascin-X are likely to compensate for missing tenascin-C during wound healing.

Chapter III: Management of cardiovascular risk factors and medical therapy

Critical limb ischaemia (CLI) is a particularly severe manifestation of lower limb atherosclerosis posing a major threat to both limb and life of affected patients. Besides arterial revascularisation, risk-factor modification and administration of antiplatelet therapy is a major goal in the treatment of CLI patients. Key elements of cardiovascular risk management are smoking cessation and treatment of hyperlipidaemia with dietary modification or statins. Moreover, arterial hypertension and diabetes mellitus should be adequately treated. In CLI patients not suitable for arterial revascularisation or subsequent to unsuccessful revascularisation, parenteral prostanoids may be considered. CLI patients undergoing surgical revascularisation should be treated with beta blockers. At present, neither gene nor stem-cell therapy can be recommended outside clinical trials. Of note, walking exercise is contraindicated in CLI patients due to the risk of worsening pre-existing or causing new ischaemic wounds. CLI patients are oftentimes medically frail and exhibit significant comorbidities. Co-existing coronary heart and carotid as well as renal artery disease should be managed according to current guidelines. Considering the above-mentioned treatment goals, interdisciplinary treatment approaches for CLI patients are warranted. Aim of the present manuscript is to discuss currently existing evidence for both the management of cardiovascular risk factors and treatment of co-existing disease and to deduct specific treatment recommendations.

Advanced nail surgery

Six techniques not yet widely known or used in the dermatologic surgery of the nails are briefly described. Small-to-medium-sized tumours of the proximal nail fold (PNF) can be excised and the defect repaired with advancement or rotation flaps. A superficial biopsy technique of the matrix for the diagnosis of longitudinal brown streaks in the nail, which allows rapid histological diagnosis of the melanocyte focus to be performed, is described here. Because the excision is very shallow and leaves the morphogenetic connective tissue of the matrix intact, the defect heals without scarring. Laterally positioned nail tumours can be excised in the manner of a wide lateral longitudinal nail biopsy. The defect repair is performed with a bipedicled flap from the lateral aspect of the distal phalanx. Malignant tumours of the nail organ often require its complete ablation. These defects can be covered by a full-thickness skin graft, reversed dermal graft, or cross-finger flap. The surgical correction of a split nail is often difficult. The cicatricial tissue of the matrix and PNF have to be excised and the re-attachment of these wounds prevented. The matrix defect has to be excised and sutured or covered with a free matrix graft taken either from the neighbouring area or from the big toe nail.

Biologicals and fetal cell therapy for wound and scar management

Few biopharmaceutical preparations developed from biologicals are available for tissue regeneration and scar management. When developing biological treatments with cellular therapy, selection of cell types and establishment of consistent cell banks are crucial steps in whole-cell bioprocessing. Various cell types have been used in treatment of wounds to reduce scar to date including autolog and allogenic skin cells, platelets, placenta, and amniotic extracts. Experience with fetal cells show that they may provide an interesting cell choice due to facility of outscaling and known properties for wound healing without scar. Differential gene profiling has helped to point to potential indicators of repair which include cell adhesion, extracellular matrix, cytokines, growth factors, and development. Safety has been evidenced in Phase I and II clinical fetal cell use for burn and wound treatments with different cell delivery systems. We present herein that fetal cells present technical and therapeutic advantages compared to other cell types for effective cell-based therapy for wound and scar management.

[Periprosthetic joint infections - a review for general practitioners]

The number of prosthetic joint implantation is continuously increasing. Periprosthetic joint infection is a rare but serious complication. The correct diagnosis is essential for successful treatment. It requires the close collaboration between general practitioners, orthopaedic surgeons and infectious disease specialists. A delayed diagnosis sets hurdles to the medical and surgical treatment. Also, antimicrobial treatment without proper microbiological sampling must be avoided. Swabs from wounds are not helpful, because the results represent the skin flora, but not the causative pathogen of infection. The general practitioner is the first physician that patients contact and has, therefore, a central role in diagnosing and managing periprosthetic joint infections. In this review, classification, diagnostic means and treatment concepts of periprosthetic joint infections are presented.

[Bullet and shrapnel injuries in the face and neck regions. Current aspects of wound ballistics]

A basic understanding of the ballistic behaviour of projectiles or fragments after entering the human body is essential for the head and neck surgeon in the military environment in order to anticipate the diagnostic and therapeutic consequences of this type of injury. Although a large number of factors influence the missile in flight and after penetration of the body, the most important factor is the amount of energy transmitted to the tissue. Long guns (rifles or shotguns) have a much higher muzzle energy compared to handguns, explaining why the remote effects beyond the bullet track play a major role. While most full metal jacket bullets release their energy after 12-20 cm (depending on the calibre), soft point bullets release their energy immediately after entry into the human body. This results in a major difference in extremity wounds, but not so much in injuries with long bullet paths (e.g. diagonal shots). Shrapnel wounds are usually produced with similarly high kinetic energy to those caused by hand- and long guns. However, fragments tend to dissipate the entire amount of energy within the body, which increases the degree of tissue disruption. Of all relevant injuries in the head and neck region, soft tissue injuries make up the largest proportion (60%), while injuries to the face are seen three times more often than injuries to the neck. Concomitant intracranial or spinal injury is seen in 30% of cases. Due to high levels of wound contamination, the infection rate is approximately 15%, often associated with a complicated and/or multiresistant spectrum of germs.

Advanced reconstructive technologies for periodontal tissue repair

Reconstructive therapies to promote the regeneration of lost periodontal support have been investigated through both preclinical and clinical studies. Advanced regenerative technologies using new barrier-membrane techniques, cell-growth-stimulating proteins or gene-delivery applications have entered the clinical arena. Wound-healing approaches using growth factors to target the restoration of tooth-supporting bone, periodontal ligament and cementum are shown to significantly advance the field of periodontal-regenerative medicine. Topical delivery of growth factors, such as platelet-derived growth factor, fibroblast growth factor or bone morphogenetic proteins, to periodontal wounds has demonstrated promising results. Future directions in the delivery of growth factors or other signaling models involve the development of innovative scaffolding matrices, cell therapy and gene transfer, and these issues are discussed in this paper.

Physiological Consequences Of White-Nose Syndrome

White-nose syndrome (WNS) is a disease that has caused the mass mortality of hibernating bat species. Since its first discovery in the winter of 2006-2007, an estimated five million bats or more have been killed. Although infection with Pseudogymnoascus destructans (Pd, the causative agent of WNS) does not always result in death, bats that survive Pd infection may experience fitness consequences. To understand the physiological consequences of WNS, I measured reproductive rates of free-ranging hibernating bat species of the Northeastern United States. In addition, captive little brown myotis (Myotis lucifugus) bats that were infected by Pd but survived (¿WNS survivors¿) and uninfected bats were studied in order to understand the potential consequences (e.g., lower reproductive rates, decreased ability to heal wounds, degradation of wing tissue, and altered metabolic rates) of surviving WNS. No differences in reproductive rates were found between WNS-survivors and uninfected bats in either the field or in captivity. In addition, wound healing was not affected by Pd infection. However, wing tissue degradation was worse for little brown myotis 19 days post-hibernation, and mass specific metabolic rate (MSMR) was significantly higher for those infected with Pd 22 days post-hibernation. While it is clear that these consequences are a direct result of Pd infection, further research investigating the long-term consequences for both mothers and pups is necessary.