Performance and mechanism of phosphorus removal in an integrated vertical flow constructed wetland treating eutrophic lake water

Phosphorus removal performance and a possible mechanism for the phosphorus removal from an eutrophic lake water were investigated using a medium-scale integrated vertical constructed wetland (combined vertical and reverse-vertical systems) from April, 11, 2001 to September, 28, 2004. Environmental factors affecting phosphorus removal and release profiles were monitored simultaneously under hydraulic loads from 400 to 2000 mm per day. The phosphorus removal rate varied with the environmental conditions. The removal rate for acidic influent water was superior to that for alkaline influent water. The substrate in the wetland chamber acted as a buffer to regulate the pH value of the water sample. As regards the water temperature, no significant differences were observed for the removal rate of total phosphorus (TP) and soluble reactive phosphorus (SRP) between low (lower than 15 degrees C) medium (16-25 degrees C) and high temperature (higher than 26 degrees C) conditions. Under a hydraulic load of 400 mm per day, the removal rate reached over 70%, the highest value achieved in this work. In addition, the highest hydraulic load of 2000 mm/d did not result in the lowest removal rate, as had been expected. After a two-year high hydraulic load test, the removal rate decreased significantly. Phosphorous release from the substrate was examined using a spatial sampling method. Depth profiles of total phosphorus and different states of phosphorus present in the substrate were recorded. This further study demonstrated that binding of phosphorus by iron and calcium might be another major factor in the removal and release of TP and SRP in this wetland system. The distribution of the speciated phosphorus showed that the amount of phosphorus captured in the substrate of the down-flow chamber was significantly higher than that captured in the up-flow chamber, suggesting that the up-flow chamber was the main source of phosphorus release in this constructed wetland.

Regulation of gamete release in the economic brown seaweed Hizikia fusiforme (Phaeophyta)

Gamete release is an essential event in artificial seeding of the economic brown seaweed, Hizikia fusiforme. Mass egg release occurred in the dark, with few eggs being discharged in the light. Release of eggs was elicited with eight practical salinity units (one PSU = 1 g sea salts l(-1)) and was inhibited by salinity levels > 32 PSU. Egg release was optimal at 23 degrees C, and was decreased by 72% in agitated seawater compared to unstirred seawater. Inhibitors of photosynthesis and ions channels suppressed egg release, indicating that this process was physiologically associated with photosynthetic activity and ion transport.

Enhancement of dissolved phosphorus release from sediment to lake water by Microcystis blooms - an enclosure experiment in a hyper-eutrophic, subtropical Chinese lake

To clarify the possible influence of Microcystis blooms on the exchange of phosphorus (P) between sediment and lake water, an enclosure experiment was conducted in the hypereutrophic subtropical Lake Donghu during July-September 2000. Eight enclosures were used: six received sediment while two were sediment-free. In mid-August, Microcystis blooms developed in all the enclosures. There was a persistent coincidence between the occurrence of Microcystis blooms and the increase of both total P (TP) and soluble reactive P (SRP) concentrations in the water of the enclosures with sediments. In sediment-free enclosures, TP and SRP concentrations remained rather stable throughout the experiment, in spite of the appearance of Microcystis blooms. The results indicate that Microcystis blooms induced massive release of P from the sediment, perhaps mediated by high pH caused by intense algal photosynthesis, and/or depressed concentrations of nitrate nitrogen (NO3-N). (C) 2002 Elsevier Science Ltd. All rights reserved.

Electrodissolution of Inorganic ions/DNA Multilayer Film for Tunable DNA Release

A layer-by-layer film composed of DNA and inorganic zirconium ion (Zr4+) was fabricated on the surface of gold thin film, and an electric field triggered disintegration of the multilayer film was studied by using electrochemical surface plasmon resonance (EC-SPR). EC-SPR results demonstrated that the film was disassembled upon the application of an electric field and the disassembly rate varied with the applied potential, leading to the controlled release of DNA. The electrodissolution could be switched off by removing the electric potential and reactivated by reapplying the potential.

Synthesis of biodegradable thermo- and pH-responsive hydrogels for controlled drug release

Novel intelligent hydrogels composed of biodegradable and pH-sensitive poly(L-glutamic acid) (PGA) and temperature sensitive poly(N-isopropylacrylamide-co-2-hydroxyethyl methacrylate) (PNH) were synthesized and characterized for controlled release of hydrophilic drug. The influence of pH on the equilibrium swelling ratios of the hydrogels was investigated. A higher PNH content resulted in lower equilibrium swelling ratios. Although temperature had little influence on the swelling behaviors of the hydrogels, the changes of optical transmittance of hydrogels as a function of temperature were marked, which showed that the PNH part of hydrogel exhibited hydrophobic property at temperature above the lower critical solution temperature (LCST). The biodegradation rate of the stimuli-sensitive hydrogels in the presence of enzyme was directly proportional to the PGA content. Lysozyme was chosen as a model drug and loaded into the hydrogels.

Optimization of conditions for tetraspore release and assessment of photosynthetic activities for different generation branches of Gracilaria lemaneiformis Bory

Gracilaria lemaneiformis Bory is an economically important alga that is primarily used for agar production. Although tetraspores are ideal seeds for the cultivation of G. lemaneiformis, the most popular culture method is currently based on vegetative fragments, which is labor-intensive and time-consuming. In this study, we optimized the conditions for tetraspore release and evaluated the photosynthetic activities of different colonies formed from the branches of G. lemaneiformis using a PAM (pulse-amplitude-modulated) measuring system. The results showed that variations in temperature and salinityhad significant effects on tetraspore yield. However, variations in the photon flux density (from 15 mu mol m(-2) s(-1) to 480 mu mol m(-2) s(-1)) had no apparent effect on tetraspore yield. Moreover, the PAM-parameters Y(I), Y(II), ETR(I), ETR(II) and F (v)/F (m) of colonies formed from different branches showed the same trend: parameter values of first generation branches > second generation branches > third generation branches. These results suggest that the photosynthetic activities of different colonies of branches changed with the same trend. Furthermore, photosynthesis in G. lemaneiformis was found to be involved in vegetative reproduction and tetraspore formation. Finally, the first generation branches grew slowly, but accumulated organic compounds to form large numbers of tetraspores. Taken together, these results showed that the first generation branches are ideal materials for the release of tetraspores.

Tank cultivation of the red alga Palmaria palmata: Year-round induction of tetrasporangia, tetraspore release in darkness and mass cultivation of vegetative thalli

Field-collected tetrasporophytes of Palmaria palmata were tumbled in 300-L outdoor tanks from January to August at ambient daylength or in a constant short-day (SD) regime (8 h light per day), both at 10 or 15 degrees C. Tetrasporangia were massively induced after 2.5 months under SD conditions at 10 degrees C and completely lacking at 15 degrees C, both under SD or ambient daylength conditions, with a few tetrasporangia present at 10 degrees C and ambient daylength. Elongation rates of tagged tetrasporophytic thalli peaked from March to April in all four conditions, when the biomass densities in the outdoor tanks were close to 2.5 kg fresh weight m(-2). Under all four conditions, juvenile proliferations started to appear in June from the margins of the old fronds, and attained approximately 1 cm in length by the end of July. Approximately 80% of the tetraspores were released during the first three dark phases in a light/dark regime, and the remaining 20% during the light phases. A minimum of 10 min darkness was observed to trigger spore release. White light inhibited tetraspore release, while a similar number of spores were released in continuous red light or in the light/dark regime, although with no significant differences of spore release during subjective days and nights. Sporelings were successfully derived from the released tetraspores for mass propagation of the male gametophyte in 2000-L outdoor tanks in a greenhouse. Mass production of male gametophytic sporelings of P. palmata was completed two times by SD induction of tetrasporangia at 10 degrees C, release of spores in darkness and culturing the sporelings until they were ready to be propagated vegetatively in greenhouse tanks. One experiment lasted from January to October 2001, with spore release in June, and the second from September to April 2003, with spore release in January. These results may support the development of sustainable, year-round Palmaria farming. (c) 2005 Elsevier B.V. All rights reserved.

Health of the older worker in Ireland - occupational physical and psychosocial factors in the autumn of work life

Introduction: Worldwide, governments are striving to keep people in work to an older age. However, little is known about the effects of work on an older workforce. This thesis aims to investigate the importance of job characteristics to the antecedents and evolution of cardiovascular disease and functional limitations for the older worker (50+ years). Methods: Three studies were used in this thesis. The 5C (Cork Coronary Care Case- Control) Study investigated the association between job strain and a coronary event in males (n=208) 35-74 years old. The Mitchelstown Study examined the association between job characteristics and positive lifestyle behaviours and further, job characteristics and blood pressure for males and females 50-69 years (n=2,047). Finally, the Cork & Kerry Study investigated the physical effects of manual work and reported functional limitations/disabilities in a sample of 60-80 year olds (n=362). Results: Results from the 5C Study show a clear difference between younger (<50 years) and older (≥50 years) workers, with older workers who had a coronary event more likely to have high job strain and low job control. Data from the Mitchelstown Study showed workers with intermediate possibility for development or high quantitative demands (versus low) at work significantly more likely to have co-occurrence of positive lifestyle behaviours. Further, those who had high possibility for development were more likely to have high systolic blood pressure with no indication of recovery from this activation at night. Physically demanding work as reported by the participants of the Cork & Kerry Study was associated with functional limitations and activities of daily living disability for both the paid and unpaid worker. Discussion: The findings from this piece of work highlight the necessity to examine job characteristics and health outcomes in isolation for the over fifties. The challenge is to get this information into the workplace.

Toxicity of manufactured nano-ZnO to Lemna minor

The rapid development of nanotechnology has led to a rise in the large-scale production and commercial use of engineered nano-ZnO. Engineered/manufactured nano-ZnO are applied in a broad range of products such as drugs, paints, cosmetics, abrasive agents and insulators. This can result in the unintended exposure of human beings to nano-ZnO and will inevitably result in the release of nano-ZnO in to the environment. Thus, it is necessary to assess the risk of nano-ZnO to the environment. In this thesis the toxicity of nano-ZnO was analysed using the aquatic, primary producer lesser duckweed (Lemna minor), and the mechanism of toxicity was analysed. Both short-term (one week) and long-term (six weeks) toxicity of nano-ZnO (uncoated) were determined. Results show that the toxicity of nano-ZnO added to the aquatic growth medium increases with increasing concentration and that toxicity accumulates with exposure time. A study of nano-ZnO dissolution reveals that the main reason for nano-ZnO toxicity on Lemna minor is the release of Zn ions. Nano-ZnO dissolution is pH dependent, and toxicity matches the release of Zn2+. Functional coating materials are commonly added to nano-ZnO particles to improve specific industrial applications. To test if coating materials contribute to nano-ZnO toxicity on lesser duckweed, the effect of silane coupling agent (KH550) coated nano-ZnO on Lemma minor was investigated. Results show that coating can decrease the release of Zn ions, which reduces toxicity to Lemna minor, in contrast to uncoated particles. Another commonly hypothesized reason for nano-ZnO toxicity is the formation of Reactive Oxygen Species (ROS) on the particles surface. As part of this thesis, the ROS formation induced by nano-ZnO was studied. Results show that nano-ZnO catalyse ROS formation and this can negatively affect duckweed growth. In conclusion, this work has detailed potentially toxic effects of nano-ZnO on Lemna minor. This study has also provides references for future research, and informs regulatory testing for nanoparticle toxicity. Specifically, the outcomes of this study emphasize the importance of exposure time, environmental parameters and coating material when analysing NPs toxicity. Firstly, impacts of longer exposure time should be studied. Secondly, environmental parameters such as pH and medium-composition need to be considered when investigating NPs toxicity. Lastly, coating of NPs should always be considered in the context of NPs toxicity, and similar NPs with different coatings require separate toxicity tests.

Development of Stimulus-Responsive Ligands for the Modulation of Copper and Iron Coordination

The ability to manipulate the coordination chemistry of metal ions has significant ramifications for the study and treatment of metal-related health concerns, including iron overload, UV skin damage, and microbial infection among many other conditions. To address this concern, chelating agents that change their metal binding characteristics in response to external stimuli have been synthesized and characterized by several spectroscopic and chromatographic analytical methods. The primary stimuli of interest for this work are light and hydrogen peroxide.

Herein we report the previously unrecognized photochemistry of aroylhydrazone metal chelator ((E)-N′-[1-(2-hydroxyphenyl)ethyliden]isonicotinoylhydrazide) (HAPI) and its relation to HAPI metal binding properties. Based on promising initial results, a series of HAPI analogues was prepared to probe the structure-function relationships of aroylhydrazone photochemistry. These efforts elucidate the tunable nature of several aroylhydrazone photoswitching properties.

Ongoing efforts in this laboratory seek to develop compounds called prochelators that exhibit a switch from low to high metal binding affinity upon activation by a stimulus of interest. In this context, we present new strategies to install multiple desired functions into a single structure. The prochelator 2-((E)-1-(2-isonicotinoylhydrazono)ethyl)phenyl (E)-3-(2,4-dihydroxyphenyl)acrylate (PC-HAPI) is masked with a photolabile trans-cinnamic acid protecting group that releases umbelliferone, a UV-absorbing, antioxidant coumarin along with a chelating agent upon UV irradiation. In addition to the antioxidant effects of the coumarin, the released chelator (HAPI) inhibits metal-catalyzed production of damaging reactive oxygen species. Finally a peroxide-sensitive prochelator quinolin-8-yl (Z)-3-(4-hydroxy-2-((4-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)benzyl)oxy)phenyl)acrylate (BCQ) has been prepared using a novel synthetic route for functionalized cis-cinnamate esters. BCQ uses a novel masking strategy to trigger a 90-fold increase in fluorescence emission, along with the release of a desired chelator, in the presence of hydrogen peroxide.

Influence of carbonation on the acid neutralization capacity of cements and cement-solidified/stabilized electroplating sludge

Portland cement (PC) and blended cements containing pulverized fuel ash (PFA) or granulated blast-furnace slag (GGBS) were used to solidify/stabilize an electroplating sludge in this work. The acid neutralization capacity (ANC) of the hydrated pastes increased in the order of PC > PC/GGBS > PC/PFA. The GGBS or PFA replacement (80 wt%) reduced the ANC of the hydrated pastes by 30–50%. The ANC of the blended cement-solidified electroplating sludge (cement/sludge 1:2) was 20–30% higher than that of the hydrated blended cement pastes. Upon carbonation, there was little difference in the ANC of the three cement pastes, but the presence of electroplating sludge (cement/sludge 1:2) increased the ANC by 20%. Blended cements were more effective binders for immobilization of Ni, Cr and Cu, compared with PC, whereas Zn was encapsulated more effectively in the latter. Accelerated carbonation improved the immobilization of Cr, Cu and Zn, but not Ni. The geochemical code PHREEQC, with the edited database from EQ3/6 and HATCHES, was used to calculate the saturation index and solubility of likely heavy metal precipitates in cement-based solidification/stabilization systems. The release of heavy metals could be related to the disruption of cement matrices and the remarkable variation of solubility of heavy metal precipitates at different pH values.

Local perceptions of the QICS experimental offshore CO2 release: Results from social science research

This paper explores the social dimensions of an experimental release of carbon dioxide (CO2) carried out in Ardmucknish Bay, Argyll, United Kingdom. The experiment, which aimed to understand detectability and potential effects on the marine environment should there be any leakage from a CO2 storage site, provided a rare opportunity to study the social aspects of a carbon dioxide capture and storage-related event taking place in a lived-in environment. Qualitative research was carried out in the form of observation at public information events about the release, in-depth interviews with key project staff and local stakeholders/community members, and a review of online media coverage of the experiment. Focusing mainly on the observation and interview data, we discuss three key findings: the role of experience and analogues in learning about unfamiliar concepts like CO2 storage; the challenge of addressing questions of uncertainty in public engagement; and the issue of when to commence engagement and how to frame the discussion. We conclude that whilst there are clearly slippages between a small-scale experiment and full-scale CCS, the social research carried out for this project demonstrates that issues of public and stakeholder perception are as relevant for offshore CO2 storage as they are for onshore.

In vitro phototoxicity of 5-aminolevulinic acid and its methyl ester and the influence of barrier properties on their release from a bioadhesive patch.

opical administration of excess exogenous 5-aminolevulinic acid (ALA) leads to selective accumulation of the potent photosensitiser protoporphyrin IX (PpIX) in neoplastic cells, which can then be destroyed by irradiation with visible light. Due to its hydrophilicity, ALA penetrates deep lesions, such as nodular basal cell carcinomas (BCCs) poorly. As a result, more lipophilic esters of ALA have been employed to improve tissue penetration. In this study, the in vitro release of ALA and M-ALA from proprietary creams and novel patch-based systems across normal stratum corneum and a model membrane designed to mimic the abnormal stratum corneum overlying neoplastic skin lesions were investigated. Receiver compartment drug concentrations were compared with the concentrations of each drug producing high levels of PpIX production and subsequent light-induced kill in a model neoplastic cell line (LOX). LOX cells were found to be quite resistant to ALA- and M-ALA-induced phototoxicity. However, drug concentrations achieved in receiver compartments were comparable to those required to induce high levels of cell death upon irradiation in cell lines reported in the literature. Patches released significantly less drug across normal stratum corneum and significantly more across the model membrane. This is of major significance since the selectivity of PDT for neoplastic lesions will be further enhanced by the delivery system. ALA/M-ALA will only be delivered in significant amounts to the abnormal tissue. PpIX will only then accumulate in the neoplastic cells and the normal surrounding tissue will be unharmed upon irradiation.

In vitro study of the efficacy of acrylic bone cement loaded with supplementary amounts of gentamicin: Effect on mechanical properties, antibiotic release, and biofilm formation

Background: Infection remains a severe complication following a total hip replacement. If infection is suspected when revision surgery is being performed, additional gentamicin is often added to the cement on an ad hoc basis in an attempt to reduce the risk of recurrent infection.

Methods and results: In this in vitro study, we determined the effect of incorporating additional gentamicin on the mechanical properties of cement. We also determined the degree of gentamicin release from cement, and also the extent to which biofilms of clinical Staphylococcus spp. isolates form on cement in vitro. When gentamicin was added to unloaded cement (1–4 g), there was a significant reduction in the mechanical performance of the loaded cements compared to unloaded cement. A significant increase in gentamicin release from the cement over 72 h was apparent, with the amount of gentamicin released increasing significantly with each additional 1 g of gentamicin added. When overt infection was modeled, the incorporation of additional gentamicin did result in an initial reduction in bacterial colonization, but this beneficial effect was no longer apparent by 72 h, with the clinical strains forming biofilms on the cements despite the release of high levels of gentamicin.

Interpretation: Our findings indicate that the addition of large amounts of gentamicin to cement is unlikely to eradicate bacteria present as a result of an overt infection of an existing implant, and could result in failure of the prosthetic joint because of a reduction in mechanical performance of the bone cement.