Geochemistry at DSDP Legs 36 and 71 Holes

For Middle Jurassic to Pleistocene times, clay mineralogical and geochemical data provide information on the evolution of continental and marine paleoenvironments. They are a source of information on marginal instability, on the continental and shallow marine environments related to the development of the Southern Ocean during the Middle and Late Jurassic, and on tectonic relaxation of the continental margins at the end of the Late Jurassic. They also provide evidence for the influences of the South Atlantic opening and the movement of the Falkland Plateau in a reduced marine environment until Aptian-Albian times, and the transition to an open marine environment during Albian time; the influences of the Albian-Turonian and Coniacian-Santonian Andean deformations in an open marine environment; the limited tectonic effects and strong influence of marine currents at the Cretaceous/Tertiary boundary; the influences of the global climatic cooling and inferred bottom water circulation during the late Eocene and Oligocene; the widening of the South Atlantic Ocean during Oligocene time, which was accompanied by an increased influence of the biogenic components on sedimentation; increased carbonate dissolution from late Oligocene to early Miocene, related to the deepening of the ocean; limited mineralogical and important geochemical modifications when the Drake Passage opened in the early Miocene; the influence of the late Miocene development of the Antarctic ice-sheet; the major Antarctic cooling and Patagonian glaciation during Pliocene time; and the change in the Antarctic Bottom Water circulation at the Pliocene/Pleistocene boundary.

Prevalencia de defectos óseos en elementos dentarios con anquilosis o reabsorción por reemplazo extraídos tempranamente

En la mayoría de los casos de dientes anquilosados la opción de tratamiento aceptado ha sido la remoción quirúrgica, la cual es frecuentemente acompañada por la rotura traumática del hueso alveolar, particularmente en los casos de la presencia de una delgada tabla vestibular del maxilar. Como en la mayoría de los casos de trauma dental y reimplantación dentaria con la subsiguiente anquilosis se involucran zonas anteriores del maxilar, tales extracciones traumáticas de los dientes anquilosados pueden llevar a deformaciones estéticas de la cresta osea, las que podrían interferir en un óptimo tratamiento protético.

Composition of minerals and rocks from the Markov Deep, Central Atlantic

The paper presents materials on composition and texture of weakly serpentinized ultrabasic rocks from the western and eastern walls of the Markov Deep (5°30.6'-5°32.4'N) in the rift valley of the Mid-Atlantic Ridge. Predominant harzburgites with protogranular and porphyroclastic textures contain two major generations of minerals: the first generation composes the bulk of rocks and consists of Ol_89.8-90.4 + En_90.2-90.8 + Di_91.8 + Chr (Cr#32.3-36.6, Mg#67.2-70.0), while the second generation composes very thin branching veinlets and consists of PlAn_32-47 + Ol_74.3-77.1 + Opx_55.7-71.9 + Cpx_67.5 + Amph_53.7-74.2 + Ilm. Syndeformational olivine neoblasts in recrystallization zones are highly magnesian. Concentrations and covariations of major elements in harzburgites indicate that these rocks are depleted in mantle residues (high Mg# of minerals and whole-rock samples and low in CaO, Al2O3, and TiO2) that are significantly enriched in trace HFSE and REE (Zr, Hf, Y, LREE, and all REE). Mineralogy and geochemistry of harzburgites were formed by interaction of mantle residues with hydrous, strongly fractionated melts that impregnated them. Mineral composition of veinlets in harzburgites and mineralogical-geochemical characteristics of related plagiogranites and gabbronorites suggest that these plagiogranites were produced by melt residuals after crystallization of gabbronorites. Modern characteristics of harzburgites were shaped by the following processes: (i) partial melting of mantle material simultaneously with its subsolidus deformations, (ii) brittle-plastic deformations associated with cataclastic flow and recrystallization, and (iii) melt percolation along zones of maximal stress relief and interaction of this melt with magnesian mantle residue.

Strength and deformation behavior of ODP Leg 110 sediments

The shape and morphology of the northern Barbados Ridge complex is largely controlled by the sediment yield and failure behavior in response to high lateral loads imposed by convergence. Loads in excess of sediment yield strength result in nonrecoverable deformations within the wedge, and failure strength acts as an upper limit beyond which stresses are released through thrust faults. Relatively high loading rates lead to delayed consolidation and in-situ pore pressures greater than hydrostatic. The sediment yield and failure behavior is described for any stress path by a generalized constitutive model. A yield locus delineates the onset of plastic (non-recoverable) deformation, as defined from the isotropic and anisotropic consolidation responses of high-quality 38-mm triaxial specimens; a failure envelope was obtained by shearing the same specimens in both triaxial compression and extension. The yield locus is shown to be rotated into extension space and is centered about a K-line greater than unity, suggesting that the in-situ major principal stress has rotated into the horizontal plane, and that the sediment wedge is being subjected to extensional effective stress paths.

Composition and properties of rocks and sediments from the Cape Verde fracture zone

The book presents results of comprehensive geological and geophysical studies, carried out in the Cape Verde fault zone in the 3-rd cruise of R/V Akademik Nikolaj Strakhov (1986). Detailed characterization of bottom relief, thickness and structure of the sedimentary cover, magnetic field, crust structure, lithology and stratigraphy of sediments, petrography and geochemistry of magmatic rocks. Conclusions about tectonic layering of the crust and upper mantle in the fault zone, and about a concurrent structural section of large mantle inhomogeneities have been done. The book is the first monographic description of a major fault structure of the ocean floor.

Chemical composition of minerals from rocks of the Utashud Island, off the Southeast Kamchatka

A brief review of various relationships connecting seismofocal zone and volcanic belts within the Kurile island-arc system is represented. Possibilities of manifestation of the submarine volcanic activity and associated relief of the hydrothermal systems on the Pacific shelf of the South Kamchatka are considered. We propose to consider Malko-Petropavlovsk zone of transverse dislocations as seismogenerating one. The phenomenon of ultrafast deformations.

Age of samples from the sedimentary cover of the Primorye continental slope and from the submarine Bogorov Rise

Results of a complex study of the sedimentary cover (continuous seismic profiling and diatom analysis) in the northeastern Sea of Japan including the Bogorov Rise an adjacent part of the Japan Basin and the continental slope, are presented. Two varied-age complexes were distinguished in the sedimentary cover of the continental slope of Primorye: Middle Miocene and Late Miocene - Pleistocene. These complexes formed in a stable tectonic setting with no significant vertical movements. A depression in the acoustic basement is located along the continental slope and it is divided from the Japan Basin by a group of volcanic structures, the most uplifted part of which forms the Bogorov Rise. The depression probably formed before Middle Miocene. In Middle Miocene the Bogorov Rise was already at depths close to modern ones. In the sedimentary cover near the Bogorov Rise buried zones were found. Probably they were channels for gas transportation in pre-Pleistocene. Deformations of sediments that occurred in the beginning of Pleistocene are established in the basin.

Fisuración y deformaciones en tabiquerías

A diferencia de otros parámetros, el efecto de la existencia de huecos en la aparición y desarrollo de los procesos de fisuración en los paños de fábrica no ha sido considerado por las distintas normativas existentes en la actualidad. En nuestros días se emplea una variada gama de tipologías de elementos de cerramiento para realizar las particiones en las obras de edificación, cada una de ellas con características mecánicas diferentes y distinta metodología de ejecución, siendo de aplicación la misma normativa relativa al cálculo y control de las deformaciones. Tal y como expresamos en el Capitulo 1, en el que se analiza el Estado del Conocimiento, los códigos actuales determinan de forma analítica la flecha probable que se alcanza en los elementos portantes estructurales bajo diferentes condiciones de servicio. Las distintas propuestas que existen respecto para la limitación de la flecha activa, una vez realizado el cálculo de las deformaciones, bien por el método de Branson ó mediante los métodos de integración de curvaturas, no contemplan como parámetro a considerar en la limitación de la flecha activa la existencia y tipología de huecos en un paño de fábrica soportado por la estructura. Sin embargo se intuye y podríamos afirmar que una discontinuidad en cualquier elemento sometido a esfuerzos tiene influencia en el estado tensional del mismo. Si consideramos que, de forma general, los procesos de fisuración se producen al superarse la resistencia a tracción de material constitutivo de la fábrica soportada, es claro que la variación tensional inducida por la existencia de huecos ha de tener cierta influencia en la aparición y desarrollo de los procesos de fisuración en los elementos de partición o de cerramiento de las obras de edificación. En los Capítulos 2 y 3 tras justificar la necesidad de realizar una investigación encaminada a confirmar la relación entre la existencia de huecos en un paño de fábrica y el desarrollo de procesos de fisuración en el mismo, se establece este aspecto como principal Objetivo y se expone la Metodología para su análisis. Hemos definido y justificado en el Capítulo 4 el modelo de cálculo que hemos utilizado para determinar las deformaciones y los procesos de fisuración que se producen en los casos a analizar, en los que se han considerado como variables: los valores de la luz del modelo, el estado de fisuración de los elementos portantes, los efectos de la fluencia y el porcentaje de transmisión de cargas desde el forjado superior al paño de fábrica en estudio. Además se adoptan dos valores de la resistencia a tracción de las fábricas, 0.75MPa y 1.00MPa. La capacidad de representar la fisuración, así como la robustez y fiabilidad ha condicionado y justificado la selección del programa de elementos finitos que se ha utilizado para realizar los cálculos. Aprovechando la posibilidad de reproducir de forma ajustada las características introducidas para cada parámetro, hemos planteado y realizado un análisis paramétricos que considera 360 cálculos iterativos, de cuya exposición es objeto el Capítulo 5, para obtener una serie representativa de resultados sobre los que se realizará el análisis posterior. En el Capítulo 6, de análisis de los resultados, hemos estudiado los valores de deformaciones y estados de fisuración obtenidos para los casos analizados. Hemos determinado la influencia que tiene la presencia de huecos en la aparición de los procesos de fisuración y en las deformaciones que se producen en las diferentes configuraciones estructurales. Las conclusiones que hemos obtenido tras analizar los resultados, incluidas en el Capítulo 7, no dejan lugar a dudas: la presencia, la posición y la tipología de los huecos en los elementos de fábricas soportadas sobre estructuras deformables son factores determinantes respecto de la fisuración y pueden tener influencia en las deformaciones que constituyen la flecha activa del elemento, lo que obliga a plantear una serie de recomendaciones frente al proyecto y frente a la reglamentación técnica. La investigación desarrollada para esta Tesis Doctoral y la metodología aplicada para su desarrollo abre nuevas líneas de estudio, que se esbozan en el Capítulo 8, para el análisis de otros aspectos que no han sido cubiertos por esta investigación a fin de mejorar las limitaciones que deberían establecerse para los Estados Límite de Servicio de Deformaciones correspondientes a las estructuras de edificación. SUMMARY. Unlike other parameters, the effect of the existence of voids in the arising and development of cracking processes in the masonry walls has not been considered by current Codes. Nowadays, a huge variety of enclosure elements types is used to execute partitions in buildings, each one with different mechanical characteristics and different execution methodology, being applied the same rules concerning deflection calculation and control. As indicated in Chapter 1, which analyzes the State of Art, current codes analytically determine the deflection likely to be achieved in structural supporting elements under different service conditions. The different proposals that exist related to live deflection limitation, once performed deformations calculation, either by Branson´s method or considering curvatures integration methods, do not consider in deflection limitation the existence and typology of voids in a masonry wall structured supported. But is sensed and it can be affirmed that a discontinuity in any element under stress influences the stress state of it. If we consider that, in general, cracking processes occur when masonry material tensile strength is exceeded, it is clear that tension variation induced by the existence of voids must have some influence on the emergence and development of cracking processes in enclosure elements of building works. In Chapters 2 and 3, after justifying the need for an investigation to confirm the relationship between the existence of voids in a masonry wall and the development of cracking process in it, is set as the main objective and it is shown the analysis Methodology. We have defined and justified in Chapter 4 the calculation model used to determine the deformation and cracking processes that occur in the cases analyzed, in which were considered as variables: model span values, bearing elements cracking state, creep effects and load transmission percentage from the upper floor to the studied masonry wall. In addition, two masonry tensile strength values 0.75MPa and 1.00MPa have been considered. The cracking consideration ability, robustness and reliability has determined and justified the selection of the finite element program that was used for the calculations. Taking advantage of the ability of accurately consider the characteristics introduced for each parameter, we have performed a parametric analyses that considers 360 iterative calculations, whose results are included in Chapter 5, in order to obtain a representative results set that will be analyzed later. In Chapter 6, results analysis, we studied the obtained values of deformation and cracking configurations for the cases analyzed. We determined the influence of the voids presence in the occurrence of cracking processes and deformations in different structural configurations. The conclusions we have obtained after analyzing the results, included in Chapter 7, leave no doubt: the presence, position and type of holes in masonry elements supported on deformable structures are determinative of cracking and can influence deformations which are the element live deflection, making necessary to raise a number of recommendations related to project and technical regulation. The research undertaken for this Doctoral Thesis and the applied methodology for its development opens up new lines of study, outlined in Chapter 8, for the analysis of other aspects that are not covered by this research, in order to improve the limitations that should be established for Deflections Serviceability Limit States related to building structures.

Comparison of experimental and numerical sloshing loads in partially filled tanks

Sloshing describes the movement of liquids inside partially filled tanks, generating dynamic loads on the tank structure. The resulting impact pressures are of great importance in assessing structural strength, and their correct evaluation still represents a challenge for the designer due to the high level of nonlinearities involved, with complex free surface deformations, violent impact phenomena and influence of air trapping. In the present paper, a set of two-dimensional cases, for which experimental results are available, is considered to assess the merits and shortcomings of different numerical methods for sloshing evaluation, namely two commercial RANS solvers (FLOW-3D and LS-DYNA), and two academic software (Smoothed Particle Hydrodynamics and RANS). Impact pressures at various critical locations and global moment induced by water motion in a partially filled rectangular tank, subject to a simple harmonic rolling motion, are evaluated and predictions are compared with experimental measurements. 2012 Copyright Taylor and Francis Group, LLC.

Robustness Analysis of Eigenstructure Assignment Controllers on Rigid-Flexible Satellites

Flexible spacecraft with attached solar panels may exhibit undesired vibrations and structural deformations. These types of vehicles show an intrinsic coupling of the elements of the structure. The attitude maneuvers performed by flexible spacecraft may cause non-desired deflections of attached flexible elements. Any attitude and orbit control system generally solves these problems using filters that are designed to attenuate the relative deflections of flexible appendages. In this paper, we propose a method for designing attitude static controllers using an eigenstructure assignment (EA) method. A set of requirements were specified from our understanding of the system modes in an open loop. Exhaustive theoretical and numerical simulations were performed on special cases to verify the controller design procedure. In the design of the controller, we considered all of the aspects that relate to the eigenstructure assignment. The primary objective of this paper is to demonstrate the feasibility of obtaining a high degree of decoupling for some selected modes via the application of an EA method. Finally a robustness analysis is perform to the system together with the designed controller by means of a mu-analysis

On the monitoring of surface displacement in connection with volcano reactivation in Tenerife, Canary Islands, using space techniques

Geodetic volcano monitoring in Tenerife has mainly focused on the Las Cañadas Caldera, where a geodetic micronetwork and a levelling profile are located. A sensitivity test of this geodetic network showed that it should be extended to cover the whole island for volcano monitoring purposes. Furthermore, InSAR allowed detecting two unexpected movements that were beyond the scope of the traditional geodetic network. These two facts prompted us to design and observe a GPS network covering the whole of Tenerife that was monitored in August 2000. The results obtained were accurate to one centimetre, and confirm one of the deformations, although they were not definitive enough to confirm the second one. Furthermore, new cases of possible subsidence have been detected in areas where InSAR could not be used to measure deformation due to low coherence. A first modelling attempt has been made using a very simple model and its results seem to indicate that the deformation observed and the groundwater level variation in the island may be related. Future observations will be necessary for further validation and to study the time evolution of the displacements, carry out interpretation work using different types of data (gravity, gases, etc) and develop models that represent the island more closely. The results obtained are important because they might affect the geodetic volcano monitoring on the island, which will only be really useful if it is capable of distinguishing between displacements that might be linked to volcanic activity and those produced by other causes. One important result in this work is that a new geodetic monitoring system based on two complementary techniques, InSAR and GPS, has been set up on Tenerife island. This the first time that the whole surface of any of the volcanic Canary Islands has been covered with a single network for this purpose. This research has displayed the need for further similar studies in the Canary Islands, at least on the islands which pose a greater risk of volcanic reactivation, such as Lanzarote and La Palma, where InSAR techniques have been used already.

Surface deformation studies of Tenerife Island, Spain from joint GPS-DInSAR observations

This work presents results for the three-dimensional displacement field at Tenerife Island calculated from campaign GPS and ascending and descending ENVISAT DInSAR interferograms. The goal of this work is to provide an example of the flexibility of the technique by fusing together new varieties of geodetic data, and to observe surface deformations and study precursors of potential activity in volcanic regions. Interferometric processing of ENVISAT data was performed with GAMMA software. All possible combinations were used to create interferograms and then stacking was used to increase signal-to-noise ratio. Decorrelated areas were widely observed, particularly for interferograms with large perpendicular baseline and large time span. Tropospheric signal was also observed which significantly complicated the interpretation. Subsidence signal was observed in the NW part of the island and around Mount Teide and agreed in some regions with campaign GPS data. It is expected that the technique will provide better results when more high quality DInSAR and GPS data is available

Bóvedas y contrarresto del Colegio de Nuestra Señora de la Antigua de Monforte de Lemos : geometría, construcción y mecánica

El Colegio de Nuestra Señora de la Antigua de Monforte de Lemos (1593-1619) constituye el principal ejemplo del clasicismo herreriano de Galicia. Esta tesis analiza los aspectos técnicos de la construcción de sus bóvedas de cantería, en el marco disciplinar de la Historia de la Construcción. El Colegio contiene varios tipos de bóvedas entre las que destacan su cúpula trasdosada y su escalera monumental. Además, se conservan los documentos notariales históricos que describen las obras y una de las monteas más importantes de Galicia. Las bóvedas han sufrido movimientos y algunas presentan importantes deformaciones, que han suscitado preocupación sobre su estabilidad. El estudio se organiza en tres epígrafes: geometría, construcción y mecánica, tres aspectos estrechamente interrelacionados en este tipo de estructuras. La parte de estudio geométrico parte de un levantamiento en el que se emplea una estación total sin reflectante, una técnica que permite una medición muy precisa de la forma real de las bóvedas. Como complemento se ha recurrido a técnicas de escáner fotográfico. Con los datos de las mediciones se han elaborado los dibujos de las bóvedas, y analizado sus medidas e irregularidades. Se ha incluido un análisis metrológico por métodos inductivos, que ha puesto de manifiesto la unidad utilizada en la construcción. El estudio se completa con la recopilación de las reglas de dimensionamiento que figuran en los tratados, que se comparan con las dimensiones de las bóvedas analizadas. En el estudio constructivo se registran los despieces y la configuración constructiva y se contrastan, por un lado, con las soluciones que aparecen en los principales tratados de los siglos XVI, XVII y XVIII, y por otro, con las descripciones que se encuentran en los documentos históricos del Colegio. Se ha prestado especial atención al estudio de estos documentos, que han permitido conocer algunos aspectos originales del proceso de construcción de estas bóvedas. En una de las paredes del claustro se ha identificado una montea inédita cuyo levantamiento y análisis se incorpora en esta parte. En el estudio mecánico se analiza la estabilidad dentro del marco teórico del Moderno Análisis Límite de Estructuras de Fábricas. La comprensión del comportamiento estructural, unida a la precisión de los levantamientos, ha permitido explicar los movimientos de las fábricas e inferir la geometría original de algunas de las bóvedas, no siempre evidente en los casos de fuertes deformaciones. Los estudios realizados hasta ahora en bóvedas de los siglos XVI y XVII permiten vislumbrar un panorama de soluciones constructivas más rico que el que recogen los tratados históricos. Las nuevas técnicas de medición sin contacto abren nuevas posibilidades para analizar estas estructuras. Los casos estudiados todavía son escasos y se necesita un conjunto más amplio para poder realizar un análisis general. Esta tesis aporta el estudio de uno de esos casos con el fin de contribuir al mejor conocimiento de la construcción en España en los siglos XVI y XVII. ABSTRACT The Colegio de Nuestra Señora de la Antigua (1593-1619), in Monforte de Lemos, Spain, is the best example in Galicia of the classicism influenced by the Monastery of El Escorial and his architect, Juan de Herrera. This thesis analyzes the technical aspects of the construction of its masonry vaults within the discipline of Construction History. The Colegio exhibits various types of vaults, among which the extradosed ashlar dome and the grand staircase are particularly worth mentioning. In addition, the legal documents containing thorough specifications of the work, as well as one of the construction drawings at actual size —one of the best examples in Galicia—, have both been preserved to this date. Some of the vaults have undergone important deformations that have raised concerns about their stability. The study is organized in three sections: geometry, construction, and mechanics, the three clearly interrelated in this type of structures. The geometrical study starts out with a metric survey using a reflectorless total station, a technique that allows a very precise measurement of the actual shape of the vault. This technique was complemented with the use of a photo-based 3D scanner. The resulting measurements were used to draw the vaults, and analyze their dimensions and irregularities. An inductive metrological analysis, which was able to reveal the exact metric unit utilized during the construction, is included in this section. The section is completed with the gathering of the dimensional rules appearing in the various historical treatises, which are compared with the dimensions of the actual vaults. The construction study deals with the quartering of the structure, whose results are compared, on the one hand, with the approaches appearing in the main treatises of the 16th- 18th centuries, and on the other, with the descriptions in the historical documents of the Colegio itself. Special attention has been paid to the study of these documents, which have revealed some original aspects in the construction process of the vaults. In one of the cloister’s walls, a hitherto unheard-of construction drawing at actual size was found. Its survey and analysis is included in this section. The mechanical study analyzes the Colegio's vaults stability within the theoretical frame of the Modern Limit Analysis of Masonry Structures. The interpretation of the structural behavior, coupled with the precision of the surveys, has allowed a deep understanding of the masonry’s movements and the original geometry of some of the vaults —not always evident in the case of strong deformations— has been inferred. The studies dealing with XVI and XVII century vaults conducted up to this date show a landscape of constructive solutions far richer than the one suggested in the historical treatises. The new contactless measuring techniques offer exciting possibilities for the analysis of these structures. The cases studied are still few and more would be needed before a general analysis can be attempted. This thesis constitutes one such additional case and its goal is to improve our understanding of Spanish construction in the 16th-17th centuries.

Radio-holografía de microondas para la optimización de la superficie de grandes antenas reflectoras

En el presente trabajo de tesis se afronta el problema de la optimización de la superficie de grandes antenas reflectoras. Es sabido que los grandes reflectores, formados por una superficie panelada, sufren deformaciones debidas al impacto del viento, a los cambios de temperatura y a los efectos gravitacionales derivados del gran peso de la estructura. Estos efectos hacen que los reflectores pierdan su forma ideal, generalmente de paraboloide, y se reduzca su eficiencia de apertura y, por tanto, se limite la máxima frecuencia de uso de los mismos. Es necesario, por tanto, disponer de técnicas que permitan medir el estado de la superficie de grandes reflectores, y derivar los ajustes necesarios a aplicar sobre los tornillos de soporte de cada uno de los paneles que conforman dicha superficie. De esta manera, se devolvería al reflector su forma óptima y aumentaría la eficiencia de apertura y el rango de frecuencias de uso. Hay que resaltar que el aumento de la eficiencia de un radiotelescopio supone una reducción en el tiempo de integración necesario para la detección de las debilísimas señales generadas por las radiofuentes naturales, ahorrando así valioso tiempo de observación. Además, el incremento en el rango de frecuencias permite la detección de nuevas líneas o especies moleculares en dichas radiofuentes. Tras un primer capítulo introductorio, se presenta, en el capítulo segundo, la geometría de estos grandes reflectores y la influencia de los distintos factores que afectan a la calidad de la superficie de los mismos, como la gravedad, el viento y la temperatura, particularizando para el caso del radiotelescopio de 40 metros del Centro Astronómico de Yebes. En el tercer capítulo, se presentan las diferentes técnicas metrológicas empleadas actualmente para abordar la determinación de estos ajustes, mostrándose las ventajas e inconvenientes de cada una de ellas. Actualmente, la técnica metrológica más precisa y rápida para llevar a cabo esta tarea de caracterización de la superficie de un gran reflector, es la radio-holografía de microondas presentada en el capítulo cuarto. A partir de las medidas proporcionadas por esta técnica, realizadas con la ayuda de un transmisor, y mediante transformaciones de campo, se calculan los errores de la superficie del reflector, respecto al paraboloide ideal, y se derivan los ajustes necesarios. En los capítulos quinto y sexto se presentan los resultados de la aplicación de esta técnica a dos radiotelescopios: el de 30 metros de IRAM en Pico de Veleta (Granada) y los prototipos de 12 metros de las antenas del proyecto ALMA. Por su parte, el capítulo séptimo contiene el núcleo fundamental de esta tesis y presenta el desarrollo de la técnica de radio-holografía de microondas para optimizar la superficie del radiotelescopio de 40 metros del Centro Astronómico de Yebes. Para ello, ha sido necesario diseñar, construir e instalar un receptor de doble canal en banda Ku en foco primario, y la instrumentación asociada para hacer las medidas de amplitud y fase del diagrama de radiación. Además, ha sido necesario desarrollar el software para llevar a cabo las transformaciones de campo y derivar los ajustes de los paneles. De las medidas holográficas iniciales resultó un error de la superficie del radiotelescopio de 485 μm WRMS, respecto al paraboloide ideal en dirección normal. Tras varias iteraciones del proceso de medida y ajuste, se consiguió reducir dicho error a 194 μm WRMS. Esta notable mejora de la calidad de la superficie ha supuesto aumentar la eficiencia de apertura desde 2,6% al 38,2% a 86 GHz, para un receptor a esta frecuencia situado en el foco primario que produjese la misma iluminación que el receptor de holografía. In this thesis the problem of large reflector antenna surface optimization is faced. It is well known that large reflectors, which are made of a panelled surface, suffer from deformations due to the impact of wind, temperature gradients and gravity loads coming from the high weigth of the structure. These effects distort the ideal reflector shape, which is a paraboloid in most cases, hence reducing the aperture efficiency of the reflector and limiting the maximum frequency of operation. Therefore, it is necessary to have some techniques to measure the status of large reflector surfaces and to derive the adjustment values to be applied to the screws that connect the surface panels to the reflector back-up structure. In this way, the reflector would recover its optimum shape and the aperture efficiency and frequency range would increase. It has to be stated that an increment in the radiotelescope aperture efficiency would imply a reduction in the integration time needed to detect such weak signals coming from natural radiosources in space and, hence, an important saving in observation time. In addition, the increase in the frequency range of operation would allow the detection of new molecular lines in those radiosources. After the introduction, the second chapter shows the geometry of large reflector antennas and the impact on its surface quality of different factors like gravity, wind and temperature, particularly for the case of the Centro Astronómico de Yebes 40 meter radiotelescope. The third chapter deals with the different metrology techniques used to determine the panel adjustments, including the advantages and drawbacks of each one Currently, the most accurate and fast metrologic technique to carry out the characterization of large reflector surfaces is microwave radio-holography2, which is shown in chapter four. From the measurements provided by microwave radio-holography, performed with the help of a transmitter, and with the use of field transformations, the reflector surface errors are computed and the panel adjustments are derived. Chapters five and six show the results of holographic measurements applied to two first class radiotelescopes: the IRAM 30 meter radiotelescope and the 12 meter prototype antennas for the ALMA project. Chapter seven contains the main work of this thesis. It presents the development of the microwave radio-holography technique for the optimization of the Centro Astronómico de Yebes 40m radiotelescope. The work implied the design, construction and instalation of a prime focus Ku-band dual channel receiver, together with the associated instrumentation to measure the amplitude and phase of the radiotelescope radiation pattern. In addition, the software to carry out field transformations and screw settings computations was developed too. Initial holography measurements came up with an surface error of 485 μmWRMS in normal direction with respect to the best-fit paraboloid. After a few iterations of the measurementadjustment cycle, the surface error was reduced to 194 μm WRMS. This remarkable improvement in surface quality means an increment in aperture efficiency from 2,6% to 38,2% at 86 GHz, assuming a receiver at this frequency in prime focus position which produces the same illumination as the holography receiver.

Clasificación de madera estructural de gran escuadría de Pinus sylvestris l. mediante métodos no destructivos

Esta Tesis Doctoral aborda el estudio de algunas técnicas no destructivas para la clasificación de madera de pino silvestre (Pinus sylvestris L.) de procedencia española y de gruesa escuadría para uso estructural. Para la estimación del módulo de elasticidad y de la resistencia se han aplicado técnicas basadas en la propagación de una onda a través de la madera: onda de ultrasonidos (Sylvatest) o de impacto (Microsecond Timer) en dirección longitudinal, o vibración en dirección longitudinal y transversal (PLG). Para la estimación de la densidad se han utilizado métodos puntuales basados en el penetrómetro (Pilodyn) y en la resistencia al arranque de un tornillo. Las variables obtenidas han sido relacionadas con los resultados de la clasificación visual y con las propiedades de la madera determinadas mediante ensayo mecánico. Además, se ha estudiado la influencia de la humedad de la madera en la velocidad de propagación de la onda para definir factores de corrección a los equipos comerciales utilizados en esta Tesis Doctoral. La muestra de estudio está formada por 244 piezas procedentes de El Espinar, Segovia, con dimensiones nominales 150 x 200 x 4000 mm (218 piezas) y 100 x 150 x 3000 mm (26 piezas). De todas las piezas se tomaron datos de dimensiones, contenido de humedad y clasificación visual según la norma UNE 56544. En las primeras 218 vigas se aplicaron las técnicas de ultrasonidos, onda de impacto y vibraciones, se determinó la densidad de cada pieza completa y se ensayaron según la norma UNE-EN 408 para obtener el módulo de elasticidad global (en todos los casos) y local (en un porcentaje), así como de la tensión de rotura. Se extrajeron tres rebanadas para los ensayos puntuales y para el cálculo de la densidad. En las otras 26 piezas se repitieron los ensayos (transmisión de onda, vibración y clasificación visual) durante el proceso de secado natural, desde que la madera se encontraba húmeda (en torno al 40 %) hasta la humedad de equilibrio higroscópico (en torno al 9%). Respecto a la clasificación visual no se han observado diferencias significativas entre la calidad MEG o las rechazadas. Se han estudiado las consecuencias del secado (principalmente las deformaciones) y no se ha encontrado justificación para que estos defectos penalicen la clasificación. Para la densidad, el mayor R2 obtenido ha sido de un 47% a partir del uso combinado de los dos equipos puntuales (penetrómetro y arranque de tornillo). Para el módulo de elasticidad y la tensión de rotura, la mejor relación se ha obtenido a partir de la técnica de vibración longitudinal, con unos coeficientes de 79% y un 52% respectivamente. Se ha estimado que el aumento de un punto porcentual en el contenido de humedad de la madera produce una pérdida de velocidad de onda del 0,58% para Sylvatest y Microsecond Timer, y del 0,71% para PLG. Estos valores son generalizables para un rango de humedades entre 9 y 25 %. Abstract This Doctoral Thesis approach the study of some non-destructive techniques as a classification method for structural use of Scots pine wood of Spanish origin with large cross section. To estimate the modulus of elasticity and strength have been used techniques based on the propagation of a wave through the timber: ultrasonic wave (Sylvatest) or stress wave (Microsecond Timer) in longitudinal direction, or vibration in longitudinal and transversal direction (PLG). Local probing methods have been applied to estimate the density, based on penetrometer (Pilodyn) and the screw withdrawal resistance meter. The different variables obtained were compared with the results of the visual grading and the values of the properties of the wood determined by the standardized test of the pieces. Furthermore, the influence of the moisture content of the wood on the velocity of propagation of the waves through the timber has been analyzed in order to establish a correction factor for the commercial devices used in this Doctoral Thesis. The sample tested consists of 244 pieces from El Espinar, Segovia, with nominal dimensions 150 x 200 x 4000 mm (218 pieces) and 100 x 150 x 3000 mm (26 pieces). Data collection about dimensions, moisture content and visual grading according to the UNE 56544 standard were carried out on all the pieces. The first 218 pieces were tested by non destructive techniques based on ultrasonic wave, stress wave and vibration, the density was measured on each piece and bending test according to the UNE-EN 408 standard was carried out for calculating the global modulus of elasticity (all the pieces) and the local one (only a representative group), as well as the bending strength. Three slices were removed for implementing the local probing and to calculate the density. In the other 26 pieces the tests (wave transmission, vibration and visual grading) were repeated during the natural drying process, from wet timber (around 40 % moisture content) up to the equilibrium moisture content (around 9%). Regarding the visual grading no significant differences were observed between MEG or rejected pieces. The effects of drying (deformations) have been studied, and justification for the specification hasn't been found. To estimate the density, the greater R2 obtained was 47% by using both penetrometer and screw withdrawal. For the modulus of elasticity and bending strength, the best relationship has been found with the longitudinal vibration, with coefficients of 79% and 52% respectively. It has been estimated that an increase of a point of the moisture content of the wood produces a decrease on the velocity obtained from ultrasonic or stress wave of 0,58%, and 0,71 % for the one obtained from vibration. Those values can be generalized for a range of moisture content from 9 to 25 %.