Influence of constituent yarn systems on the moisture management performance of terry fabrics

Objetivo do presente trabalho foi estudar a influência dos diferentes sistemas de fios (trama, teia de base e teia da argola) no desempenho dos tecidos de felpos, no que concerne às propriedades de absorção, capilaridade e libertação de humidade. Para este estudo usaram-se quatro tipos de combinações destes sistemas de fios, para a mesma estrutura de tecidos de felpo, na teia de base utilizou-se somente fios de Tencel®, na teia de argola e da trama varou-se a composição dos fios entre fios de algodão e de Tencel®. Os resultados obtidos demonstram que quando a utilização fios de Tencel® em qualquer dos sistemas (trama ou teia da argola) favorece a capacidade de difusão de líquidos na estrutura, a utilização de fios de algodão na teia de argola favorece a capacidade de absorção.

Simulation of OWES with five-Level converter linked to the grid: Harmonic assessment

This paper deals with a computing simulation for an offshore wind energy system taking into account the influence of the marine waves action throughout the floating platform. The wind energy system has a variable-speed turbine equipped with a permanent magnet synchronous generator and a full-power five level converter, injecting energy into the electric grid through a high voltage alternate current link. A reduction on the unbalance of the voltage in the DC-link capacitors of the five-level converter is proposed by a strategic selection of the output voltage vectors. The model for the drive train of the wind energy system is a two mass model, including the dynamics of the floating platform. A case study is presented and the assessment of the quality of the energy injected into the electric grid is discussed.

Simulation of a rectifier malfunction on a offshore wind system with HVDC transmission

A new integrated mathematical model for the simulation of an offshore wind system having a rectifier input voltage malfunction at one phase is presented in this paper. The mathematical model considers an offshore variable-speed wind turbine on a floating platform, equipped with a permanent magnet synchronous generator using full-power three-level converter to inject energy into the electric network, through a high voltage direct current transmission submarine cable. The model for the drive train is a discrete three mass, incorporating the dynamic of the moving surface. A case study is presented to access conclusion about the malfunction.

Wear of PEEK-Ti6Al4V systems under micro-abrasion and linear sliding conditions

Dissertação de mestrado integrado em Engenharia Biomédica

Numerical simulation of the reflow soldering process

Dissertação de mestrado integrado em Mechanical Engineering

An integrated model for simulation of construction phasing of arch concrete dams

Dissertação de mestrado integrado em Civil Engineering

Sefficiency (sustainable efficiency) of water–energy–food entangled systems

Supplemental data for this article can be accessed at http://dx.doi.org/10.1080/07900627.2015.1070091. It includes an easy-to-use spreadsheet that calculates the efficiencies used in this paper, that is Sefficiency with energy considerations.

In-line rheo-optical microstructural characterization of complex polymer systems

Tese de Doutoramento em Ciência e Engenharia de Polímeros e Compósitos.

Single molecule simulation of diffusion and enzyme kinetics

This work presents a molecular-scale agent-based model for the simulation of enzymatic reactions at experimentally measured concentrations. The model incorporates stochasticity and spatial dependence, using diffusing and reacting particles with physical dimensions. We developed strategies to adjust and validate the enzymatic rates and diffusion coefficients to the information required by the computational agents, i.e., collision efficiency, interaction logic between agents, the time scale associated with interactions (e.g., kinetics), and agent velocity. Also, we tested the impact of molecular location (a source of biological noise) in the speed at which the reactions take place. Simulations were conducted for experimental data on the 2-hydroxymuconate tautomerase (EC 5.3.2.6, UniProt ID Q01468) and the Steroid Delta-isomerase (EC 5.3.3.1, UniProt ID P07445). Obtained results demonstrate that our approach is in accordance to existing experimental data and long-term biophysical and biochemical assumptions.

Mejoramiento del comportamiento térmico de sistemas de calentamiento de agua solares termosifónicos hechos con materiales no convencionales y con tanques de almacenamiento verticales y horizontales Performance improvement of solar thermosyphonic systems for water heating made of non conventional materials and using horizontal and vertical storage tanks

El objeto de estudio de este proyecto son los sistemas de calentamiento de agua mediante energía solar que funcionan termosifónicamente. En particular se tratará con dos diseños particulares generados por fabricantes de la Provincia de Córdoba y que han solicitado el asesoramiento del Grupo de Energía Solar (GES) para el mejoramiento de la performance térmica de dichos equipos. Se trata de dos sistemas que tienen materiales no tradicionales y se diferencian además por tener una distinta disposición del tanque de almacenamiento: uno es en forma vertical y el otro en forma horizontal. Basados en los resultados de un ensayo bajo norma internacional, donde se detectaron algunas puntos factibles de mejora, se propone en este proyecto el análisis en detalle de los equipos, para lo cual se les debe desarmar completos, para realizar un estudio analítico y experimental de los mismos con el objeto de hacer un planteo teórico-analítico del comportamiento de los mismos, con la implementación de propuestas de mejora y chequeo de los resultados. Se propone entonces como objetivo lograr un mejoramiento de la performance térmica de los citados equipos a partir de un estudio experimental y analítico. Asumiendo esta posibilidad de mejora, se plantea la hipótesis de que es posible representar el funcionamiento de estos equipos mediante modelos físico-matemáticos desarrollados a partir de ecuaciones y correlaciones conocidas y procesos a interpretar mediante resoluciones numéricas y softwares específicos de simulación. De esta manera, se plantea el despieze completo de los equipos para estudiar en detalle su estructura y conexiones internas y a partir de la geometría, dimensiones y propiedades termofísicas de materiales constructivos y fluidos de trabajo, realizar modelos físico-matemáticos que permitan realizar variaciones de propiedades y geometría y así buscar las mejores combinaciones que produzcan equipos más eficientes térmicamente. Los modelos físico-matemáticos serán codificados en lenguajes de alto nivel para poder luego de una validación de los modelos, correr simulaciones en un software de reconocimiento internacional que permite sumar dichos modelos mediante un protocolo de comunicación, haciendo que las poderosas prestaciones del software se puedan aplicar a nuestros modelos. Se complementará el estudio con un análisis exergético para identificar los puntos críticos en que se producen las pérdidas de oportunidad de aprovechar la energía disponible, para así analizar cómo solucionar los problemas en dichos puntos. Los materiales a utilizar serán los propios equipos provistos por los fabricantes, que serán modificados convenientemente para operarlos como prototipos Se espera obtener un conocimiento acabado de los procesos y principios de funcionamiento de los equipos, que permita plantear las mejoras, las cuales se implementarán en los prototipos, realizándose una medición mediante norma igual a la inicial para ver en que magnitud se logran las mejoras esperadas. Se pretende además que las mejoras a implementar, en la etapa de transferencia a las empresas involucradas, redunden no sólo en un beneficio técnico, sino que también los sea desde el punto de vista económico. Para ello se trabajará también sobre los procesos y métodos de fabricación para que los equipos mejorados no sean mas caros que los originales y de ser posible sean aún más económicos, todo esto apuntando a la difusión de la energía solar térmica y poner al alcance de todos estos equipos tan convenientes para la propagación de las energías limpias. El proyecto redundará también en un importante beneficio para el conocimiento de la comunidad científica en general, con el aporte de nuevos resultados en diseños novedosos y con nuevos materiales. Además, la institución se beneficiará con la formación que obtendrán los integrantes del proyecto, muchos de ellos en etapa de realización de sus estudios de posgrado y en una etapa importante de su vida como investigadores. The main goal of this project is the improvement of two thermosyphonic solar water heating systems, made of non conventional materials and with different arrangement of their storage tanks: one is vertical and the other one horizontal. The thermosyphonic systems are provided by manufacturers of the Córdoba Province, who came to the Solar Energy Group (GES) of the National University of Río Cuarto looking for help for the design of their products. In an agreement with these manufacturers, it was proposed this project in order to work analytically and experimentally in order to obtain physical-mathematical models of these two systems, which allow for changes to look by means of simulations the best changes to implement on the equipments for the improvement of their thermal performance. Then, the materials to be used are the proper systems provided by the manufacturers, which will be disarmed to be studied in detail. After the analytical study the proposals of improvement will be implemented in a high level language of programming to perform simulations in the environment of a well-known software for energy simulations (TRNSYS). After the simulations, the best modifications will be physically implemented in the prototypes to perform finally the same normalized test of the beginning and check the magnitude of the implemented improvements. The importance of this project is based on the offer of better systems the companies would make, which would benefit the deployment of the thermal solar energy. Another relevant point is to make the new equipments at the same cost of the previous ones or cheaper, in order to achieve a good deployment of the solar water heating systems; then, the manufacture processes and methods must be studied to obtain not only good technical solutions, but also economical equipments. In addition, this project will contribute to the increasing of the knowledge in the area of thermosyphonic solar systems and the training of postgraduate students.

Aproximación al diseño de sistemas de bio-reactores para la delignificación de materiales lignocelulósicos y para la decontaminación de suelos y efluentes. Approximation to the design of bio-reactors systems for the delignificación of lignocellulosic materials and for the decontamination of soil and effluents

Los materiales lignocelulósicos residuales de las actividades agroindustriales pueden ser aprovechados como fuente de lignina, hemicelulosa y celulosa. El tratamiento químico del material lignocelulósico se debe enfrentar al hecho de que dicho material es bastante recalcitrante a tal ataque, fundamentalmente debido a la presencia del polímero lignina. Esto se puede lograr también utilizando hongos de la podredumbre blanca de la madera. Estos producen enzimas lignolíticas extracelulares fundamentalmente Lacasa, que oxida la lignina a CO2. Tambien oxida un amplio rango de sustratos ( fenoles, polifenoles, anilinas, aril-diaminas, fenoles metoxi-sustituídos, y otros), lo cual es una buena razón de su atracción para aplicaciones biotecnológicas. La enzima tiene potencial aplicación en procesos tales como en la delignificación de materiales lignocelulósicos y en el bioblanqueado de pulpas para papel, en el tratamiento de aguas residuales de plantas industriales, en la modificación de fibras y decoloración en industrias textiles y de colorantes, en el mejoramiento de alimentos para animales, en la detoxificación de polutantes y en bioremediación de suelos contaminados. También se la ha utilizado en Q.Orgánica para la oxidación de grupos funcionales, en la formación de enlaces carbono- nitrógeno y en la síntesis de productos naturales complejos. HIPOTESIS: Los hongos de podredumbre blanca, y en condiciones óptimas de cultivo producen distintos tipos de enzimas oxidasas, siendo las lacasas las más adecuadas para explorarlas como catalizadores en los siguientes procesos:  Delignificación de residuos de la industria forestal con el fin de aprovechar tales desechos en la alimentación animal.  Decontaminación/remediación de suelos y/o efluentes industriales. Se realizarán los estudios para el diseño de bio-reactores que permitan responder a las dos cuestiones planteadas en la hipótesis. Para el proceso de delignificación de material lignocelulósico se proponen dos estrategias: 1- tratar el material con el micelio del hongo adecuando la provisión de nutrientes para un desarrollo sostenido y favorecer la liberación de la enzima. 2- Utilizar la enzima lacasa parcialmente purificada acoplada a un sistema mediador para oxidar los compuestos polifenólicos. Para el proceso de decontaminación/remediación de suelos y/o efluentes industriales se trabajará también en dos frentes: 3) por un lado, se ha descripto que existe una correlación positiva entre la actividad de algunas enzimas presentes en el suelo y la fertilidad. En este sentido se conoce que un sistema enzimático, tentativamente identificado como una lacasa de origen microbiano es responsable de la transformación de compuestos orgánicos en el suelo. La enzima protege al suelo de la acumulación de compuestos orgánicos peligrosos catalizando reacciones que involucran degradación, polimerización e incorporación a complejos del ácido húmico. Se utilizarán suelos incorporados con distintos polutantes(por ej. policlorofenoles ó cloroanilinas.) 4) Se trabajará con efluentes industriales contaminantes (alpechínes y/o el efluente líquido del proceso de desamargado de las aceitunas). The lignocellulosic raw materials of the agroindustrial activities can be taken advantage as source of lignin, hemicellulose and cellulose. The chemical treatment of this material is not easy because the above mentioned material is recalcitrant enough to such an assault, due to the presence of the lignin. This can be achieved also using the white-rot fungi of the wood. It produces extracellular ligninolitic enzymes, fundamentally Laccase, which oxidizes the lignin to CO2. The enzyme has application in such processes as in the delignification of lignocellulosic materials and in the biobleaching of fibers for paper industry, in the treatment of waste water of industrial plants, in the discoloration in textile industries, in the improvement of food for ruminants, in the detoxification of polutants and in bioremediation of contaminated soils. HYPOTHESIS: The white-rot fungi produce different types of enzymes, being the laccases the most adapted to explore them as catalysts in the following processes:  Delignification of residues of the forest industry in order to take advantage of such waste in the animal feed.  Decontamination of soils and / or waste waters. The studies will be conducted for the design of bio reactors that allow to answer to both questions raised in the hypothesis. For the delignification process of lignocellulosic material they propose two strategies: 1- to treat the material with the fungi 2-to use the partially purified enzyme to oxidize the polyphenolic compounds. For the soil and/or waste water decontamination process, we have: 3- Is know that the enzyme protects to the soil of the accumulation of organic dangerous compounds catalyzing reactions that involve degradation, polymerization and incorporation to complexes of the humic acid. There will be use soils incorporated into different pollutants. 4- We will work with waste waters (alpechins or the green olive debittering effluents.

An emperical study of performance management systems in SMEs in the Republic of Ireland and the People's Republic of China : a cultural perspective

The objectives of this thesis are three. Firstly, finding and analyzing the differences of performance management system in SMEs in Ireland and China. Secondly, finding the cultural differences between China and Ireland and thirdly, integrating the research outcomes of the above research objectives, and then analyzing the effect of these cultural differences on performance management system in SMEs in China and Ireland.

A comparison of environmental licensing systems in operation in the wood panel manufacturing industry in the Northern Hemisphere

The objective of this thesis is to compare and contrast environmental licensing systems, for the wood panel industry, in a number of countries in order to determine which system is the best from an environmental and economic point of view. The thesis also examines the impact which government can have on industry and the type of licensing system in operation in a country. Initially, the thesis investigates the origins of the various environmental licensing systems which are in operation in Ireland, Scotland, Wales, France, USA and Canada. It then examines the Environmental Agencies which control and supervise industry in these countries. The impact which the type of government (i.e. unitary or federal) in charge in any particular country has on industry and the Regulatory Agency in that country is then described. Most of the mills in the thesis make a product called OSB (Oriented Strand Board) and the manufacturing process is briefly described in order to understand where the various emissions are generated. The main body of the thesis examines a number of environmental parameters which have emission limit values in the licenses examined, although not all of these parameters have emission limit values in all of the licenses. All of these parameters are used as indicators of the potential impact which the mill can have on the environment. They have been set at specific levels by the Environmental Agencies in the individual countries to control the impact of the mill. Following on from this, the two main types of air pollution control equipment (WESPs and RTOs) are described in regard to their function and capabilities. The mill licenses are then presented in the form of results tables which compare air results and water results separately. This is due to the fact that the most significant emission from this type of industry is to air. A matrix system is used to compare the licenses so that the comparison can be as objective as possible. The discussion examines all of the elements previously described and from this it was concluded that the IPC licensing system is the best from an environmental and economic point of view. It is a much more expensive system to operate than the other systems examined, but it is much more comprehensive and looks at the mill as a whole rather than fragmenting it. It was also seen that the type of environmental licensing system which is in place in a country can play a role in the locating of an industry as certain systems were seen to have more stringent standards attached to them. The type of standard in place in a country is in turn influenced by the type of government which is in place in that country.

Process simulation of lime calcination in mixed feed shaft kilns

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2012

Direct numerical simulation of turbulent flames on parallel computers

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2012