Coatings on Composites

Polymer based composite materials coated with thin layers of wear resistant materials have been proposed as replacements for steel components for certain applications with the advantage of reduced mass. Magnetron sputtered coatings can be successfully deposited on composite materials. Nevertheless there are number of issues which must be addressed such as limited temperature, which the composite can withstand because of the epoxy binder which is used, the adhesion of the coating to the composite and the limited mechanical support, the hard coating can obtain from the relatively soft epoxy. We have investigated the deposition of chromium nitride, titanium carbide and titanium doped DLC coatings on carbon fibre reinforced composites and various polymers. The adhesion of the coatings has been studied by the pull-off adhesion tester. In general, the failure mechanism has been noticed to be due to the cohesive failure for a wide range of conditions. The wear behavior of the coatings has been noticed to be complicated. Wear tests on coated composites have shown that where the reinforcing fibres are near the surface, the composite samples do not perform well due to breakage of the fibres from the polymer matrix. A fibre free surface has been noticed to improve the wear resistance.

The Effects of Corruption and Seigniorage on Growth and Inflation

In the last two decades, cases of corruption have been unveiled in different countries, raising public awareness and reinforcing a trend in which society expects more from their leaders. Our objective in this paper is to examine the effects of corruption and seigniorage on inflation and growth rates. The model used in this article is an extension of the model used by Huang and Wei (2006). We find interesting results and one of them is that, under some conditions, corruption has a positive impact on the growth rate. JEL classification : D73, E52, E58, E62. Keywords : Corruption; Fiscal Policy; Growth; Monetary Policy; Seigniorage.

Barlike

El objetivo de este proyecto es el desarrollo de la aplicación Android Barlike. La aplicación pretende ser un espacio social para compartir opiniones y datos sobre restaurantes y bares de tapas.

Catalytic gasification of glycerol in supercritical water

The conversion of glycerol in supercritical water (SCW) was studied at 510-550 °C and a pressure of 350 bars using both a bed of inert and non-porous ZrO2 particles (hydrothermal experiments), and a bed of a 1% Ru/ZrO2 catalyst. Experiments were conducted with a glycerol concentration of 5 wt% in a continuous isothermal fixed-bed reactor at a residence time between 2 and 10 s. Hydrothermolysis of glycerol formed water-soluble products such as acetaldehyde, acetic acid, hydroxyacetone and acrolein, and gases like H2, CO and CO2. The catalyst enhanced the formation of acetic acid, inhibited the formation of acrolein, and promoted gasification of the glycerol decomposition products. Hydrogen and carbon oxides were the main gases produced in the catalytic experiments, with minor amounts of methane and ethylene. Complete glycerol conversion was achieved at a residence time of 8.5 s at 510 °C, and at around 5 s at 550 °C with the 1 wt% Ru/ZrO2 catalyst. The catalyst was not active enough to achieve complete gasification since high yields of primary products like acetic acid and acetaldehyde were still present. Carbon balances were between 80 and 60% in the catalytic experiments, decreasing continuously as the residence time was increased. This was attributed partially to the formation of methanol and acetaldehyde, which were not recovered and analyzed efficiently in our set-up, but also to the formation of carbon deposits. Carbon deposition was not observed on the catalyst particles but on the surface of the inert zirconia particles, especially at high residence time. This was related to the higher concentration of acetic acid and other acidic species in the catalytic experiments, which may polymerize to form tar-like carbon precursors. Because of carbon deposition, hydrogen yields were significantly lower than expected; for instance at 550 °C the hydrogen yield potential was only 50% of the stoichiometric value.

The scrutiny of the principle of subsidiarity by autonomous regional parliaments with particular reference to the participation of the Parliament of Catalonia in the early warning system

The purpose of this article is to offer a practical approach to the new European dimension for regional parliaments signified by the entry into force of the Treaty of Lisbon. The parliamentary scrutiny of subsidiarity by way of the early warning system has assigned a new mission to legislative assemblies with the aim of reinforcing the intervention of regions in the drafting of policies by Union institutions. In the Spanish case, the institutionalisation of this mechanism came about with Act nº 24/2009, which attributes to the Joint Committee for the European Union, in the name of the Cortes Generales [the Spanish Parliament], the function of receiving the proposals for legislative acts by the EU and transferring them to the regional parliaments in order for the latter to issue, in a brief period of four weeks, a report on compliance with the principle of subsidiarity. The majority of regional parliaments have also carried out normative reforms to regulate the procedure of participation in the early warning system.

Analysis of the tensile modulus of polypropylene composites reinforced with stone groundwood fibers

One of the most relevant properties of composite materials to be considered is stiffness. Fiberglass has been used traditionally as a fibrous reinforcing element when stiff materials are required. However, natural fibers are been exploited as replacements for synthetic fibers to satisfy environmental concerns. Among the different natural fibers, wood fibers show the combination of relatively high aspect ratio, good specific stiffness and strength, low density, low cost, and less variability than other natural fibers of such those from annual crops. In this work, composites from polypropylene and stone groundwood fibers from softwood were prepared and mechanically characterized under tensile loads. The Young’s moduli of the ensuing composites were analyzed and their micromechanics aspects evaluated. The reinforcing effect of stone groundwood fibers was compared to that of conventional reinforcement such fiberglass. The Halpin-Tsai model with the modification proposed by Tsai-Pagano accounted fairly for the behavior of PP composites reinforced with stone groundwood fibers. It was also demonstrated that the aspect ratio of the reinforcement plays a role in the Young’s modulus of injection molded specimens

Research on the suitability of organosolv semi-chemical triticale fibers as reinforcement for recycled hdpe composites

The main objective of this research was to study the feasibility of incorporating organosolv semi-chemical triticale fibers as the reinforcing element in recycled high density polyethylene (HDPE). In the first step, triticale fibers were characterized in terms of chemical composition and compared with other biomass species (wheat, rye, softwood, and hardwood). Then, organosolv semi-chemical triticale fibers were prepared by the ethanolamine process. These fibers were characterized in terms of its yield, kappa number, fiber length/diameter ratio, fines, and viscosity; the obtained results were compared with those of eucalypt kraft pulp. In the second step, the prepared fibers were examined as a reinforcing element for recycled HDPE composites. Coupled and non-coupled HDPE composites were prepared and tested for tensile properties. Results showed that with the addition of the coupling agent maleated polyethylene (MAPE), the tensile properties of composites were significantly improved, as compared to non-coupled samples and the plain matrix. Furthermore, the influence of MAPE on the interfacial shear strength (IFSS) was studied. The contributions of both fibers and matrix to the composite strength were also studied. This was possible by the use of a numerical iterative method based on the Bowyer-Bader and Kelly-Tyson equations

Modelo de comportamiento en sevicio para estructuras reticulares de hormigón. Parte I: Descripción del modelo y ejemplos de aplicación

A general method for instantaneous and time-dependent serviceability analysis of plane concrete frames is presented. The methodology is based in an extension of the classic matrix formulation for bars. The main aspects influencing the behaviour of the structural concrete are considered: cracking, creep, shrinkage or prestress losses. To simulate the effect of cracking a smeared model (developed in Part II) based on the modification of the tensile branch of the concrete stress-strain relationship is adopted. The general approach considered permits the application to different materials and constitutive laws. Sequential construction (sectional and structural), incorporation of reinforcement, consideration of the loads history; placing and removing shores, and restraining or releasing in boundary conditions are considered. Some examples are included to highlight the capabilities of the model

High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

Kehittyneiden hitsausprosessien soveltuvuus alumiinin ja hiiliterästen hitsaukseen

Diplomityössä tutkitaan hitsausprosessien kehitystä. Työn kirjallisen osan alku kuvaa hitsauksen nykypäivää ja tulevaisuutta sekä millainen on hitsaava Suomi. Kehittyneiden hitsausprosessien tarkastelu on jaettu hiiliterästen ja alumiinien hitsausprosesseihin. Hiiliteräksien hitsauksen osalta työssä esitellään kitkahitsaus pyörivällä työkalulla, muunnettu lyhytkaarihitsaus, laserhitsaus, laser-hybridihitsaus ja kapearailohitsaus. Alumiinien hitsauksen osalta työssä esitellään laserhitsaus, muunnettu lyhytkaarihitsaus, kitkahitsaus pyörivällä työkalulla ja vaihtovirta MIG hitsaus. Diplomityön käytännönosuudessa todennettiin hitsausprosessien kehitys. Ensimmäisissä hitsauskokeissa hitsattiin merialumiinia eri kaarityypeillä. Vertailua tehdään pulssihitsauksen, lankapulssihitsauksen sekä CMT-kaarihitsauksen välillä. Koehitsaukset osoittavat CMT-hitsauksen tuottavan MIG-pulssihitsausta pienemmät hitsausmuodonmuutokset. CMT-hitsauksessa alumiinin oksidikerros aiheuttaa MIGpulssihitsausta vähemmän ongelmia, sillä kaari syttyy varmemmin suurillakin hitsausnopeuksilla, eikä hitsiin synny huokosia. Hitsausnopeudella 40 cm/min lankapulssihitsauksella ja MIG-pulssihitsauksella päittäisliitoksena hitsattujen vesileikattujen alumiinikappaleiden hitseihin ei syntynyt huokosia. Kokeen perusteella voidaan todeta, ettei oksidikerroksella ollut vaikutusta hitsin onnistumiseen. Hitsauskokeiden toinen osio tutkii hiilimangaaniteräksisen T-palkin kuitulaserhitsausta. Viiden kilowatin laserteholla hitsattiin onnistuneesti viisi metriä pitkiä T-palkkeja hitsausnopeudella 2 m/min. Takymetrimittauksella ja Tritop 3D-koordinaattimittauksella todennettiin laserhitsatun T-palkin hitsausmuodonmuutosten olevan huomattavasti Twin-jauhekaarihitsauksella hitsattua T-palkkia pienemmät.

Small and Large Scale Dynamics in the Milky Way

This thesis contains dynamical analysis on four different scales: the Solar system, the Sun itself, the Solar neighbourhood, and the central region of the Milky Way galaxy. All of these topics have been handled through methods of potential theory and statistics. The central topic of the thesis is the orbits of stars in the Milky Way. An introduction into the general structure of the Milky Way is presented, with an emphasis on the evolution of the observed value for the scale-length of the Milky Way disc and the observations of two separate bars in the Milky Way. The basics of potential theory are also presented, as well as a developed potential model for the Milky Way. An implementation of the backwards restricted integration method is shown, rounding off the basic principles used in the dynamical studies of this thesis. The thesis looks at the orbit of the Sun, and its impact on the Oort cloud comets (Paper IV), showing that there is a clear link between these two dynamical systems. The statistical atypicalness of the orbit of the Sun is questioned (Paper I), concluding that there is some statistical typicalness to the orbit of the Sun, although it is not very significant. This does depend slightly on whether one includes a bar, or not, as a bar has a clear effect on the dynamical features seen in the Solar neighbourhood (Paper III). This method can be used to find the possible properties of a bar. Finally, we look at the effect of a bar on a statistical system in the Milky Way, seeing that there are not only interesting effects depending on the mass and size of the bar, but also how bars can capture disc stars (Paper II).

Online Ultrasound Measurements of Membrane Compaction

There are several filtration applications in the pulp and paper industry where the capacity and cost-effectiveness of processes are of importance. Ultrafiltration is used to clean process water. Ultrafiltration is a membrane process that separates a certain component or compound from a liquid stream. The pressure difference across the membrane sieves macromolecules smaller than 0.001-0.02 μm through the membrane. When optimizing the filtration process capacity, online information about the conditions of the membrane is needed. Fouling and compaction of the membrane both affect the capacity of the filtration process. In fouling a “cake” layer starts to build on the surface of the membrane. This layer blocks the molecules from sieving through the membrane thereby decreasing the yield of the process. In compaction of the membrane the structure is flattened out because of the high pressure applied. The higher pressure increases the capacity but may damage the structure of the membrane permanently. Information about the compaction is needed to effectively operate the filters. The objective of this study was to develop an accurate system for online monitoring of the condition of the membrane using ultrasound reflectometry. Measurements of ultrafiltration membrane compaction were made successfully utilizing ultrasound. The results were confirmed by permeate flux decline, measurements of compaction with a micrometer, mechanical compaction using a hydraulic piston and a scanning electron microscope (SEM). The scientific contribution of this thesis is to introduce a secondary ultrasound transducer to determine the speed of sound in the fluid used. The speed of sound is highly dependent on the temperature and pressure used in the filters. When the exact speed of sound is obtained by the reference transducer, the effect of temperature and pressure is eliminated. This speed is then used to calculate the distances with a higher accuracy. As the accuracy or the resolution of the ultrasound measurement is increased, the method can be applied to a higher amount of applications especially for processes where fouling layers are thinner because of smaller macromolecules. With the help of the transducer, membrane compaction of 13 μm was measured in the pressure of 5 bars. The results were verified with the permeate flux decline, which indicated that compaction had taken place. The measurements of compaction with a micrometer showed compaction of 23–26 μm. The results are in the same range and confirm the compaction. Mechanical compaction measurements were made using a hydraulic piston, and the result was the same 13 μm as obtained by applying the ultrasound time domain reflectometry (UTDR). A scanning electron microscope (SEM) was used to study the structure of the samples before and after the compaction.

Regional innovation strategies and sustainability in selected EU countries

This study focuses on regional innovation strategy (RIS) and sustainability aspects in selected regions of European Union (EU) countries. It is known that RIS helps a region to innovate locally and to compete globally and it is considered as one of the main policy tools of the EU for innovation support at a regional level. This study is conducted to explore the existence and adoption of RIS in different regions of selected EU countries, and to highlight and compare regional RIS characteristics. The study is also aimed at identifying the factors that characterise the formulation and implementation of RIS as well as the problems associated thereof. In this study, six regions of EU countries are considered: Päijät-Häme Region (Finland); London Region (United Kingdom); Mid-West Region (Ireland); Veneto Region (Italy); Eastern Region (Poland); and West Region (Romania). Data and information are collected by sending questionnaires to the respective regional authorities of these selected regions. Based on the gathered information and analysis, RIS or equivalent strategy document serves as a blueprint for forwarding innovative programmes towards regional sustainability. The objectives of RIS in these regions are found to be dependent on the priority sectors and state of the region’s development. The current environmental sustainability aspects are focused on eco-design, eco-products, and eco-innovation, although each region also has its own specific aspects supported by RIS. Likewise, regional policies typically follow the RIS yet translated in various sectoral focus or priority areas. The main enhancing factors supporting RIS among selected regions have some similarities and variations; among others, some regions are strongly supported by EU while others have support from own regional agencies, organisations and professional networks. RIS implementation is not without challenges and despite the differences in challenges, almost all of reviewed regions consider financial resource as a common problem. Generally, it is learned from this study that RIS and regional sustainability are reinforcing each other mutually. In this study, the strong focus is given towards environmental sustainability in the regions although regional sustainability also includes economic and social aspects. A well-focused and prioritised RIS is beneficial for regional sustainable development.

High-speed solid-rotor induction machine – calculation program

The aim of this thesis is to utilize the technology developed at LUT and to provide an easy tool for high-speed solid-rotor induction machine preliminary design. Computer aided design tool MathCAD has been chosen as the environment for realizing the calculation program. Four versions of the design program have been made depending on the motor rotor type. The first rotor type is an axially slitted solid-rotor with steel end rings. The next one is an axially slitted solid-rotor with copper end rings. The third machine type is a solid rotor with deep, rectangular copper bars and end rings (squirrel cage). And the last one is a solid-rotor with round copper bars and end rings (squirrel cage). Each type of rotor has its own specialties but a general thread of design is common. This paper follows the structure of the calculating program and explains some features and formulas. The attention is concentrated on the difference between laminated and solid-rotor machine design principles. There is no deep analysis of the calculation ways are presented. References for all solution methods appearing during the design procedure are given for more detailed studying. This thesis pays respect to the latest innovations in solid-rotor machines theory. Rotor ends’ analytical calculation follows the latest knowledge in this field. Correction factor for adjusting the rotor impedance is implemented. The purpose of the created design program is to calculate the preliminary dimensions of the machine according to initial data. Obtained results are not recommended for exact machine development. Further more detailed design should be done in a finite element method application. Hence, this thesis is a practical tool for the prior evaluating of the high-speed machine with different solid-rotor types parameters.

Usable Privacy Preservation in Mobile Electronic Personality

Personalised ubiquitous services have rapidly proliferated due technological advancements in sensing, ubiquitous and mobile computing. Evolving societal trends, business and the economic potential of Personal Information (PI) have overlapped the service niches. At the same time, the societal thirst for more personalised services has increased and are met by soliciting deeper and more privacy invasive PI from customers. Consequentially, reinforcing traditional privacy challenges and unearthed new risks that render classical safeguards ine ective. The absence of solutions to criticise personalised ubiquitous services from privacy perspectives, aggravates the situation. This thesis presents a solution permitting users' PI, stored in their mobile terminals to be disclosed to services in privacy preserving manner for personalisation needs. The approach termed, Mobile Electronic Personality Version 2 (ME2.0), is compared to alternative mechanisms. Within ME2.0, PI handling vulnerabilities of ubiquitous services are identi ed and sensitised on their practices and privacy implications. Vulnerability where PI may leak through covert solicits, excessive acquisitions and legitimate data re-purposing to erode users privacy are also considered. In this thesis, the design, components, internal structures, architectures, scenarios and evaluations of ME2.0 are detailed. The design addresses implications and challenges leveraged by mobile terminals. ME2.0 components and internal structures discusses the functions related to how PI pieces are stored and handled by terminals and services. The architecture focusses on di erent components and their exchanges with services. Scenarios where ME2.0 is used are presented from di erent environment views, before evaluating for performance, privacy and usability.