Influence of a tilted cavity on quantum-dot optoelectronic active devices

Quantum-dot laser diodes (QD-LDs) with a Fabry-Perot cavity and quantum-dot semiconductor optical amplifiers (QD-SOAs) with 7° tilted cavity were fabricated. The influence of a tilted cavity on optoelectronic active devices was also investigated. For the QD-LD, high performance was observed at room temperature. The threshold current was below 30 mA and the slope efficiency was 0.36 W/A. In contrast, the threshold current of the QD-SOA approached 1000 mA, which indicated that low facet reflectivity was obtained due to the tilted cavity design.A much more inverted carrier population was found in the QD-SOA active region at high operating current, thus offering a large optical gain and preserving the advantages of quantum dots in optical amplification and processing applications. Due to the inhomogeneity and excited state transition of quantum dots, the full width at half maximum of the electroluminescence spectrum of the QD-SOA was 81.6 nm at the injection current of 120 mA, which was ideal for broad bandwidth application in a wavelength division multiplexing system. In addition, there was more than one lasing peak in the lasing spectra of both devices and the separation of these peak positions was 6-8 nm,which is approximately equal to the homogeneous broadening of quantum dots.

Investigation of high cycle and Very-High-Cycle Fatigue behaviors for a structural steel with smooth and notched specimens

The high cycle and Very-High-Cycle Fatigue (VHCF) properties of a structural steel with smooth and notched specimens were studied by employing a rotary bending machine with frequency of 52.5 Hz. For smooth specimens, VHCF failure did occur at fatigue cycles of 7.1 x 10(8) with the related S-N curve of stepwise tendency. Scanning Electron Microscopy (SEM) was used for the observations of the fracture surfaces It shows that for smooth specimens the crack origination is surface mode in the failure regime of less than 10(7) cycles While at VHCF regime, the material failed from the nonmetallic inclusion lies in the interior of material, leading to the formation of fisheye pattern. The dimensions of crack initiation region were measured and discussed with respect to the number of cycles to failure. The mechanism analysis by means of low temperature fracture technique shows that the nonmetallic inclusion in the interior of specimen tends to debond from surrounding matrix and form a crack. The crack propagates and results to the final failure. The stress intensity factor and fatigue strength were calculated to investigate the crack initiation properties. VHCF study on the notched specimens shows that the obtained S-N curve decreases continuously. SEM analysis reveals that multiple crack origins are dominant on specimen surface and that fatigue crack tends to initiate from the surface of the specimen. Based on the fatigue tests and observations, a model of crack initiation was used to describe the transition of fatigue initiation site from subsurface to surface for smooth and notched specimens. The model reveals the influences of load, grain size, inclusion size and surface notch on the crack initiation transition. (C) 2010 Elsevier Ltd. All rights reserved

RNAi沉默烟草GA 20-氧化酶基因研究

赤霉素是一种高效能的广谱植物生长调节剂，为五大植物激素之一，具有重要的生物学功能。目前利用赤霉素突变体研究生物合成途径和信号转导已经成为热点。 GA 20-氧化酶是GA生物合成中的一类关键酶，它位于GA合成途径的中心位置。本研究根据烟草（Nicotiana tabacum）GA 20-氧化酶基因序列，设计2对分别含有特定酶切位点的特异引物，以烟草基因组DNA为模板，扩增目的基因(约250 bp)片段。将正、反向目的片段分别插入中间载体的内含子两侧，再经BamH I和Sac I双酶切回收约700 bp的目的片段，插入到双元载体质粒p2355中，成功构建了含GA 20-氧化酶基因片段反向重复序列的植物表达载体p23700。分别将p2355质粒和p23700质粒导入根癌农杆菌（Agrobacterium tumefaciens）EHA105中并转化烟草叶片细胞，经卡那霉素选择培养，PCR及GUS组织染色鉴定，获得转基因烟草植株。以EHA105-p2355转化的烟草，获得41株转基因植株，均没有矮化表型；而以EHA105-p23700转化的烟草，获得转基因植株14株，其中具有矮化表型的烟草10株，表明反向重复序列转录产物能形成发夹RNA(hpRNA)，产生小分子干扰RNA（small interferring RNA，简称siRNA），干扰目的基因的表达。 赤霉素含量测定表明矮化植株中赤霉素合成途径的最终产物GA3总含量明显低于野生型烟草植株。荧光定量PCR结果表明，矮化转基因烟草的GA 20-氧化酶基因表达量受到明显抑制，表达量明显低于野生型对照。同时对上游内根-贝壳杉合成酶（Ent-kaurene synthase，KS）基因，下游的GA-3β羟化酶基因进行了RT-PCR分析，结果显示上游基因的表达没有规律性变化，而下游基因表达量亦降低。上述结果表明，GA 20-氧化酶基因的表达被有效地干扰了，表达受到抑制，从而影响植株体内GA3的合成，影响植株的生长发育，导致植株矮化。并推测，GA 20-氧化酶基因受到抑制，可能影响下游基因的表达。并且通过干旱胁迫测试，发现矮化植株相对于野生型植株及不含干扰片段的转基因植株，对干旱的耐受力有了很大的提高，具有更强的耐受力。 研究结果为进一步进行相关研究奠定基础。 Gibberellin(GA) is an efficient plant growth regulator. As one of five major plant hormones, it plays an important biological function. Using GA mutant for investigating biosynthetic pathways and signal transduction has become high lights. GA 20-oxidase is a crucial enzyme involved in gibberellin biosynthesis. According to tobacco (Nicotiana tabacum) GA 20-oxidase enzyme gene sequence and based on binary vector p2355, we constructed a plant expression vector p23700, which habors an inverted repeat DNA fragment of GA 20-oxidase gene drivered by Cauliflower mosaic virus promtor (CaMV 35Sp). Binary plasmid p2355 had no inverted repeat DNA fragment of GA 20-oxidase gene. The vector p2355 and p23700 were introduced into Agrobacterium tumefaciens EHA105 and tobacco leaf transformation was conducted. After selected by kanamycin and characterized by PCR and GUS hischemical reaction, transsgenic plants were obtained. Fourtheen transgenic plants, which were transformed by EHA105-p23700, were obtained. Among them, 10 were dwarf mutants. However, 41 transgenic plants with the same normal phenotype as wild type,which were transformed by EHA105-p2355, were obtained. Analysis of Gibberellin contents showed that it was lower in dwarf mutants than in normal phenotype plants. Moreover, comparing to normal phenotype plants including wild type and transgenic plants with no interference fragment, the drought tolerance of dwarf plants have greatly increased. And their proline content increased obviously after drought test. Fluorescence quantitative real time PCR (RT-PCR) showed that GA 20-oxidase gene expression was significantly inhibited in dwarf transgenic tobacco. Meanwhile, the expression of the upstream gene ent-kaurene synthase (KS) gene and downstream gene GA-3β hydroxylase gene was also detected by RT-PCR. The results presented that KS gene expression had no regular change while GA-3β hydroxylase gene expression reduced. It implied that inhibiting GA 20-oxidase gene probably reduce the expression of downstream genes. The results showed that the transcriptional products of the foreign inverted repeat fragment can form hairpin RNA (hpRNA) to induce RNAi. It presented that GA 20-oxidase gene expression was effectively interfered, resulting in reducing GA3 synthesis and inhibiting plant growth and development, then dwarf plants were produced. However, the dwarf plants had higher tolerance of drought.

微生物法生成辅酶Q10的研究

本文根据我们实验室建立的发酵产物中辅酶Q10定性定量检测方法，筛选得到一株可以代谢产生较多辅酶Q10的野生菌株放射形土壤杆菌(Agrobacterium radiobacter No.50)。 为了提高放射形土壤杆菌的辅酶Q10的产量，本实验利用液体培养研究了单因素对菌株辅酶Q10产量的影响，并用正交法确定了最佳液态发酵条件。最佳发酵培养基是：葡萄糖20g,蔗糖40g, 硫酸铵10g,玉米浆30g, 酵母膏3g，K2HPO4 3g,MgSO4.7H2O 1g，蒸馏水1000mL,pH 7.0-7.2。最佳发酵条件是：转接斜面菌种到种子培养基, 转速220r/min、温度28。C培养24h后，转入发酵培养基(250mL三角拼装液量为50mL，pH 7.0), 接种量为10％，转速220r/min、温度28。C，培养120h。在此条件下，菌体湿重约为50g/L，辅酶Q10含量约为20mg/L。 本文以放射形土壤杆菌为出发菌株进行诱变育种，以期获得辅酶Q10高产菌。根据微生物育种原理、参照辅酶Q10的代谢调控机制，以野生型放射形土壤杆菌(Agrobacterium radiobacter No.50)为出发菌株，采用紫外线和亚硝基胍复合诱变技术，依次筛选得到菌体提取物M抗性菌ARM－7、烟草提取物T抗性菌株ARMT-26、Vk3抗性菌株ARMTV-25、链霉素抗性菌株ARMTVS-32，菌株ARMTVS-32产量达到了36.8mg/L，与原始出发菌株相比，产量提高了77％。 研究了茄尼醇、对羟基苯甲酸、橘子皮提取物D、胡萝卜提取物E、烟草提取物对ARMTVS-32合成辅酶Q10的影响，结果表明这些物质对菌体合成辅酶Q10有一定促进作用，添加0.2g/L茄尼醇时，辅酶Q10含量提高了17%，达到了40.7mg/L；添加1.2g/L橘子皮提取物D时，辅酶Q10含量提高了13.8%，达到了39.6mg/L；添加0.5g/L胡萝卜提取物E时，辅酶Q10含量提高了25.3% ，达到了43.6mg/L；添加8g/L烟草提取物时，辅酶Q10含量提高了12.6%，达到了39.2mg/L。 Production of Coenzyme- Q10 (CoQ10) by fermentation is considered as a process with broad prospects.Quantitative Analysis of CoQ10 in the culture of microbe by TLC—UV spectrophotometry was developed, by using this method we got the strain Agrobacterium radiobacter,which was isolated from forest soil of southwest of China. The effect of the single factor on CoQ10-production ability of the strain was examined by liquid cultured, and its best optimum cultivation conditions were established by orthogonal method. The results showed that the optimum fermentation conditions were as following: carbon sources glucose 20g/L,sucrose 40g/L; nitrongen sources (NH4)2SO4 10g/L,maize liquid 30g/L;yeast extract 3g; K2HPO4 3g/L,MgSO4.7H2O 1g/L; initial pH was 7 and volume of medium(medium volume vs flask volume) was 50mL/500mL, incubating for 120h on a rotary shaker at 220 rpm and 28℃.Under these conditions, the biomass and CoQ10 concentration reached 50g/L and 20mg/L respectively. According to the biosynthesis mechanism of CoQ10 and breeding theory, CoQ10 over-production strains were screened by UV--NTG. mutation using Agrobacterium radiobacter No.50 as parent strain. A microbe-juice resistant mutant ARMTVS-32, which also could resist tobacco-juice, VK3 and streptomycin, was screened out from an agar plate. The CoQ10 content of ARMTVS-32 reached 36.8mg/L, which was 77% higher than the initial strain. In addition, We discussed the effects of some organic substrates on the synthesis of CoQ10 in ARMTVS-32. The results showed that solanesol, orange juice D, carrot juice E and tobacco juice could promote the CoQ10 accumulation in the cells. The CoQ10 content of ARMTVS-32 reached 40.7mg/L when added 0.2g/L solanesol,it reached 39.6mg/L when added 1.2g/L orange juice D，it reached 43.6mg/L when added 0.5g/L carrot juice E. it reached 39.2mg/L when added 8g/L tobacco juice.

Effects of Naotan Pill on repair of neural cells and cognitive disorders in juvenile rats following hypoxia and ischemia

BACKGROUND: Hypoxia and ischemia induce neuronal damage, decreased neuronal numbers and synaptophysin levels, and deficits in learning and memory functions. Previous studies have shown that lycium barbarum polysaccharide, the most effective component of barbary wolfberry fruit, has protective effects on neural cells in hypoxia-ischemia. OBJECTIVE: To investigate the effects of Naotan Pill on glutamate-treated neural cells and on cognitive function in juvenile rats following hypoxia-ischemia. DESIGN, TIME AND SETTING: The randomized, controlled, in vivo study was performed at the Cell Laboratory of Lanzhou University, Lanzhou Institute of Modern Physics of Chinese Academy of Sciences, and Department of Traditional Chinese Medicine of Gansu Provincial Rehabilitation Center Hospital, China from December 2005 to August 2006. The cellular neurobiology, in vitro experiment was conducted at the Institute of Human Anatomy, Histology, Embryology and Neuroscience, School of Basic Medical Sciences, Lanzhou University, and Department of Traditional Chinese Medicine of Gansu Provincial Rehabilitation Center Hospital, China from March 2007 to January 2008. MATERIALS: Naotan Pill, composed of barbary wolfberry fruit, danshen root, grassleaf sweetflag rhizome, and glossy privet fruit, was prepared by Gansu Provincial Rehabilitation Center, China. Rabbit anti-synaptophysin, choline acetyl transferase polyclonal antibody, streptavidin-biotin complex kit and diaminobenzidine kit (Boster, Wuhan, China), as well as glutamate (Hualian, Shanghai, China) were used in this study. METHODS: Cortical neural cells were isolated from neonatal Wistar rats. Neural cell damage models were induced using glutamate, and administered Naotan Pill prior to and following damage. A total of 54 juvenile Wistar rats were equally and randomly assigned into model, Naotan Pill, and sham operation groups. The left common carotid artery was ligated, and then rat models of hypoxic-ischemic injury were assigned to the model and Naotan Pill groups. At 2 days following model induction, rats in the Naotan Pill group were administered Naotan Pill suspension for 21 days. In the model and sham operation groups, rats received an equal volume of saline. MAIN OUTCOME MEASURES: Neural cell morphology was observed using an inverted phase contrast microscope. Survival rate of neural cells was measured by MTT assay. Synaptophysin and choline acetyl transferase expression was observed in the hippocampal CA1 region of juvenile rats using immunohistochemistry. Cognitive function was tested by the Morris water maze. RESULTS: Pathological changes were detected in glutamate-treated neural cells. Neural cell morphology remained normal after Naotan Pill intervention. Absorbance and survival rate of neural cells were significantly greater following Naotan Pill intervention, compared to glutamate-treated neural cells (P < 0.05). Synaptophysin and choline acetyl transferase expression was lowest in the hippocampal CA1 region in the model group and highest in the sham operation group. Significant differences among groups were observed (P < 0.05). Escape latency and swimming distance were significantly longer in the model group compared to the Naotan Pill group (P < 0.05). CONCLUSION: Naotan Pill exhibited protective and repair effects on glutamate-treated neural cells. Naotan Pill upregulated synaptophysin and choline acetyl transferase expression in the hippocampus and improved cognitive function in rats following hypoxia-ischemia.

Quantitative sample injection for capillary electrophoresis

An apparatus including a rotary-type injector was designed for quantitative sample injection in capillary electrophoresis (CE), in which both pressurized flow and electroosmotic flow were used to drive the background electrolyte solution. A relative standard deviation of peak area of lower than 1% was achieved by using this apparatus. The effects of back-pressure regulator, restrictor, and applied voltage on separation efficiency and resolution were investigated. The utility of this apparatus in both micro-HPLC and pressurized capillary electrochromatography (pCEC) was also demonstrated.

Two-dimensional capillary electrophoresis involving capillary isoelectric focusing and capillary zone electrophoresis

Capillary isoelectric focusing (cIEF) and capillary zone electrophoresis (CZE) was on-line hyphenated by a dialysis interface to achieve a 2D capillary electrophoresis (CE) system. The system was used with just one high-voltage power supply and three electrodes (one cathode shared by the two dimensions). The focused zone in the first dimension (i.e. the cIEF) was driven to the dialysis interface by electroosmotic flow (EOF), besides chemical mobilization from the first anode to the shared cathode. And then in the second dimension (i.e. the CZE), the separated zone was further separated and driven by an inverted EOF, which originated from the charged layer of a cationic surfactant adsorbed onto the inner wall of the capillary. Finally, a solution of ribonuclease was rapidly separated to assess the feasibility of the two-dimensional CE implement. (C) 2003 Elsevier B.V. All rights reserved.

水窖沉沙池结构形式试验设计

通过对单厢式矩形断面、单厢式梯形断面、迷宫式、旋流式等 4种结构形成的沉沙池沉沙效率对比试验表明 ,以迷宫式沉沙池效果最佳 ,平均沉沙效率可达 88.3%。此种结构形式的断面尺寸为 1m、宽 0 .4m ,迷宫室底部比集水渠低 0 .2 m,迷宫分成 5个小厢室 ,每个厢室长 0 .146 m,沉沙池首部的静水池深 0 .2 5 m

A biofuel cell with enhanced performance by multilayer biocatalyst immobilized on highly ordered macroporous electrode

A one-compartment glucose/O-2. biofuel cell based on an electrostatic layer-by-layer (LbL) technique on three-dimensional ordered macroporous (3DOM) gold electrode was described. A 3DOM gold electrode was synthesized electrochemically by an inverted colloidal crystal template technique. Then the macroporous gold electrodes were functionalized with Au nanoparticles (AuNPs) and enzyme, glucose dehydrogenase (GDH) or laccase.

Effect of the nature of annealing solvent on the morphology of diblock copolymer blend thin films

The morphologies and structures for the thin film of blend systems consisting of two asymmetric polystyrene-block-polybutadiene (SB) diblock copolymers induced by annealing in the vapor of different solvents, namely, cyclohexane, benzene, and heptane, which have different selectivity or preferential affinity for a certain block, were investigated by tapping mode atomic force microscopy (AFM) and transmission electron microscopy (TEM). The results revealed that even a slight preferential affinity of good solvent for one block would strongly alter the morphology of the blend thin film.

Synthesis and characterization of phenylene-thiophene all-conjugated diblock copolymers

Grignard metathesis (GRIM) polymerization for all-conjugated diblock copolymers comprising poly (2,5-dihexyloxy-1,4-phenylene) (PPP) and poly(3-hexylthiophene) (P3HT) blocks were systematically studied with LiCl as additive and 1,2-bis (diphenylphosphino) ethane nickel dichloride (Ni(dppe)Cl-2) or 1,3-bis(diphenylphosphino) propane nickel dichloride (Ni(dppp)Cl-2) as catalyst. It was found that the addition order of the monomers was crucial for the success of copolymerization. With the monomer addition in the order of phenyl and then thienyl Grignard reagents, all-conjugated PPP-b-P3HT diblock copolymers with different block ratios were successfully synthesized. In contrast, the inverted addition order only afforded a mixture containing both block copolymers and deactivated or end-capped homopolymers.

Core Crosslinking of Biodegradable Block Copolymer Micelles Based on Poly(ester carbonate)

A biodegradable amphiphilic block copolymer, PEG-b-P(LA-co-MAC), was used to prepare spherical micelles consisting of a hydrophobic P(LA-co-MAC) core and a hydrophilic PEG shell. To improve their stability, the micelles were crosslinked by radical polymerization of the double bonds in the hydrophobic blocks. The crosslinked micelles had similar sizes and a narrow size distribution compared to their uncrosslinked precursor. The improved stability of the crosslinked micelles was confirmed by measurements of the CMC and a thermodynamic investigation. These micelles can internalize into Hela cells in vitro as demonstrated by inverted fluorescence microscopy and CLSM. These stabilized nanoscale micelles have potential use in biomedical applications such as drug delivery and disease diagnosis.

Solvent-induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: The Block Length and Composition Dependence of Morphology

A series of binary SB blend samples with various overall volume fraction of PS (Phi(PS)) and different discrete distribution of the block length (denoted as d(PS) or d(PB)) were prepared by mixing various asymmetric poly(styrene)-block-poly(butadiene) (SB) block copolymers with a symmetric SB block copolymer. The influences of the external solvent field, composition, and the block length distribution on the morphologies of the blends in the thin films were investigated by atomic force microscopy (AFM) and transmission electron microscopy (TEM). The experimental results revealed that after solvent annealing, the interface of the blend thin films depended mainly on the cooperative effects of the annealing solvent and the inherently interfacial curvature of the blends. Upon exposure to the saturated vapor of cyclohexane, which has preferential affinity for the PB block, a "threshold" of Phi(PS) (approximate 0.635-0.707) was found. Below such threshold, the influence of the annealing solvent played an important role on the interfacial curvature of the blend thin film.

Investigation of facilitated ion-transfer reactions at high driving force by scanning electrochemical Microscopy

The kinetics of facilitated ion-transfer (FIT) reactions at high driving force across the water/1,2-dichloroethane (W/DCE) interface is investigated by scanning electrochemical microscopy (SECM). The transfers of lithium and sodium ions facilitated by dibenzo-18-crown-6 (DB18C6) across the polarized W/DCE interface are chosen as model systems because they have the largest potential range that can be controlled externally. By selecting the appropriate ratios of the reactant concentrations (Kr c(M)+/c(DB18C6)) and using nanopipets as the SECM tips, we obtained a series of rate constants (k(f)) at various driving forces (Delta(O)(W) phi(ML+)(0') - Es, Delta(O)(W) phi(ML+)(0') is the formal potential of facilitated ion transfer and Es is the potential applied externally at the substrate interface) based on a three-electrode system. The FIT rate constants k(f) are found to be dependent upon the driving force. When the driving force is low, the dependence of 1n k(f) on the driving force is linear with a transfer coefficient of about 0.3. It follows the classical Butler-Volmer theory and then reaches a maximum before it decreases again when we further increase the driving forces. This indicates that there exists an inverted region, and these behaviors have been explained by Marcus theory.

Solvent-induced novel morphologies in diblock copolymer blend thin films

We report the morphology and phase behaviors of blend thin films containing two poly styrene-b-poly (methyl methacrylate) (PS-b-PMMA) diblock copolymers with different blending compositions induced by a selective solvent for the PMMA block, which were studied by transmission electron microscopy (TEM). The neat asymmetric PS-b-PMMA diblock copolymers employed in this study, respectively coded as a(1) and a(2), have similar molecular weights but different volume fractions of PS block (f(PS) = 0.273 and 0.722). Another symmetric PS-b-PMMA diblock copolymer, coded as s, which has a PS block length similar to that of a(1), was also used. For the asymmetric a(1)/a(2) blend thin films, circular multilayered structures were formed. For the asymmetric a(1)/symmetric s blend thin films, inverted phases with PMMA as the dispersed domains were observed, when the weight fraction of s was less than 50%. The origins of the morphology formation in the blend thin films via solvent treatment are discussed. Combined with the theoretical prediction by Birshtein et al. (Polymer 1992, 33, 2750), we interpret the formation of these special microstructures as due to the packing frustration induced by the difference in block lengths and the preferential interactions between the solvent and PMMA block.