Morphology and melt rheology of nylon 11/clay nanocomposites

Nylon 11 (PA11)/clay nanocomposites have been prepared by melt-blending, followed by melt-extrusion through a capillary. Transmission electron n-Licroscopy shows that the exfoliated clay morphology is dominant for low nanofiller content, while the intercalated one is prevailing for high filler loading. Melt rheological properties of PA11 nanocomposites have been studied in both linear and nonlinear viscoelastic response regions. In the linear regime, the nanocomposites exhibit much higher storage modulus (G') and loss modulus (G") values than neat PAIL The values of G' and G" increase steadily with clay loading at low concentrations, while the G' and G" for the sample with 5 wt % clay show an inverse dependence and lie between the modulus values of the samples with 1 and 2 wt % of clay. This is attributed to the alignment/orientation of nanoclay platelets in the intercalated nanocomposite induced by capillary extrusion. In the nonlinear regime, the nanocomposites show increased shear viscosities when compared with the neat resin. The dependence of the shear viscosity on clay loading has analogous trend to that of G' and G".

Monte Carlo simulation of the grafting of maleic anhydride onto polypropylene at higher temperature

The graft of maleic anhydride (MAH) onto isotactic polypropylene (iPP) initiated by dicumyl peroxide (DCP) at 190 degreesC was studied by means of the Monte Carlo method. The ceiling temperature theory, i.e., no possibility for the homopolymerization of MA-H to occur at higher temperatures, was used in this study. The simulation results show that most MAH monomers were grafted onto the radical chain ends arising from beta scission at a lower MAH concentration, whereas the amount of MAH monomers attached to the tertiary carbons was much larger than that grafted onto the radical chain ends at a higher MAH concentration for various DCP concentrations. This conclusion gives a good interpretation for the disagreement on the grafting sites along a PP chain. Moreover, it was found that the grafting degree increased considerably up to a peak value; thereafter, it decreased continuously with increasing MA-H concentration. The peak shifted in the lower MAH concentration direction and became lower and lower with increasing DCP concentration. When the DCP concentration was below 0.1 wt %, the peak was hardly observed. Those results are in good agreement with the experiments.

Morphology, structure, and properties of in situ compatibilized linear low-density polyethylene/polystyrene and linear low-density polyethylene/high-impact polystyrene blends

Blends of linear low-density polyethylene (LLDPE) with polystyrene (PS) and blends of LLDPE with high-impact polystyrene (HIPS) were prepared through a reactive extrusion method. For increased compatibility of the two blending components, a Lewis acid catalyst, aluminum chloride (AlCl3), was adopted to initiate the Friedel-Crafts alkylation reaction between the blending components. Spectra data from Raman spectra of the LLDPE/PS/AlCl3 blends extracted with tetrahydrofuran verified that LLDPE segments were grafted to the para position of the benzene rings of PS, and this confirmed the graft structure of the Friedel-Crafts reaction between the polyolefin and PS. Because the in situ generated LLDPE-g-PS and LLDPE-g-HIPS copolymers acted as compatibilizers in the relative blending systems, the mechanical properties of the LLDPE/PS and LLDPE/HIPS blending systems were greatly improved. For example, after compatibilization, the Izod impact strength of an LLDPE/PS blend (80/20 w/w) was increased from 88.5 to 401.6 J/m, and its elongation at break increased from 370 to 790%. For an LLDPE/HIPS (60/40 w/w) blend, its Charpy impact strength was increased from 284.2 to 495.8 kJ/m(2). Scanning electron microscopy micrographs showed that the size of the domains decreased from 4-5 to less than 1 mum, depending on the content of added AlCl3.

Thermal properties and morphology of noncrosslinking linear low-density polyethylene-grafted acrylic acid

Noncrosslinking linear low-density polyethylene-grafted acrylic acid (LLDPE-g-AA) was prepared by melt-reactive extrusion in our laboratory. The thermal behavior of LLDPE-g-AA was investigated by using differential scanning calorimetry (DSC). Compared with neat linear low-density polyethylene (LLDPE), melting temperature (T-m) of LLDPE-g-AA increased a little, the crystallization temperature (T-c) increased about 4degreesC, and the melting enthalpy (DeltaH(m) ) decreased with an increase in acrylic acid content. Isothermal crystallization kinetics of LLDPE and LLDPE-g-AA samples were carried out by using DSC. The overall crystallization rate of LLDPE was smaller than that of grafted samples. It showed that the grafted acrylic acid monomer onto LLDPE acted as a nucleating agent. Crystal morphologies of LLDPE-g-AA and LLDPE were examined by using SEM. Spherulite sizes of LLDPE-g-AA samples were lower than that of LLDPE.

Effect of the compatibilization of linear low-density polyethylene-g-acrylic acid on the morphology and mechanical properties of poly(butylene terephthalate)/linear low-density polyethylene blends

A poly(butylene terephthalate) (PBT)/linear low-density polyethylene (LLDPE) alloy was prepared with a reactive extrusion method, For improved compatibility of the blending system, LLDPE grafted with acrylic acid (LLDPE-g-AA) by radiation was adopted in place of plain LLDPE. The toughness and extensibility of the PBT/LLDPE-g-AA blends, as characterized by the impact strengths and elongations at break, were much improved in comparison with the toughness and extensibility of the PBT/LLDPE blends at the same compositions. However, there was not much difference in their tensile (or flexural) strengths and moduli. Scanning electron microscopy photographs showed that the domains of PBT/LLDPE-g-AA were much smaller and their dispersions were more homogeneous than the domains and dispersions of the PBT/ T,T PE blends. Compared with the related values of the PBT/LLDPE blends, the contents and melting temperatures of the usual spherulites of PBT in PBT/LLDPE-g-AA decreased.

Toughening PA1010 with a functionalized saturated polyolefin elastomer

Polyamide (PA)1010 is blended with a saturated polyolefin elastomer, ethylene-cu-olefin copolymer (EOCP). To improve the compatibility of PA1010 with EOCP, different grafting rates of EOCP with maleic anhydride (MA) are used. The reaction between PA1010 and EOCP-g-MA during extrusion is verified through an extraction test. Mechanical properties, such as notched Izod impact strength, elongation at break, etc., are examined as a function of grafting rate and weight fraction of elastomer. It was found that in the scale of grafting rate (0.13-0.92 wt %), 0.51 wt % is an extreme point for several mechanical properties. Elastomer domains of PA1010/ EOCP-g-MA blends show a finer and more uniform dispersion in the matrix than that of PA1010/EOCP blends. For the same grafting rate, the average sizes of elastomer particles are almost independent on the contents of elastomer, but for different grafting rates, the particle sizes are decreased with increasing grafting rate. The copolymer formed during extrusion strengthens the interfacial adhesion and acts as an emulsifier to prevent the aggregation of elastomer in the process of blending. (C) 2000 John Wiley & Sons, Inc.

Magnetic microsphere and its use in biochemical separation and analysis

Magnetic microsphere comprises a magnetically responsive metal or metal oxide core surrounded by a polymer shell with active groups. Nowadays, methods of directly coating polymer, monomer polymerazation, impregnation, extrusion and biological synthesis are generally used to prepare magnetic particles. This kind of superparamagnetic microspheres can be attached to chemical, biochemical and biological substances by their active groups, then applying a magnetic field to separate from the media. Preparation and utilization of magnetic microspheres in immunoassay, nucleic acid hybrization assay, gene sequencing, cell isolation, enzyme immoblization, receptor isolation and other Gelds are reviewed with 44 references in this paper. Also, the further development is outlooked.

Liquid crystalline polymer as a processing agent in blends of poly(ether-ketone)/LCP70

Blends of a liquid crystalline thermotropic copolyester (LCP70) and an amorphous phenolphthalein based poly(ether-ketone)(PEK-C) with two viscosities were prepared by melt blending. The blends' morphology, rheological and mechanical properties were investigated by DSC, SEM, mechanical and rheological tests. It was observed that the optimum composition of the PEK-C/LCP70 blend was 10 wt% LCP for both mechanical and rheological properties. When the LCP content was less than 10%, the LCP phase existed as finely dispersed fibrous domains with a diameter of about 1 mu m in the matrix, and both tensile and flexural properties were improved. In contrast, when the LCP content reached 20% or more, the LCP domains coalesced to ellipsoidal particles with a diameter of about 5 mu m, and the mechanical properties decreased as a result. It is demonstrated that pure PEK-C with a high viscosity which was difficult to process by melt extrusion, could be extruded conveniently when 10% LCP70 was incorporated. It is emphasized that LCP not only can be used as a reinforcing phase but also an effective processing agent for engineering thermoplastics, especially for those with high viscosity and narrow processing window. (C) 1997 Elsevier Science Ltd.

The phase inversion and morphology of nylon 1010 polypropylene blends

Noncompatibilized and compatibilized blends of nylon 1010/PP blends having five different viscosity ratios were prepared by melt extrusion. Glycidyl methacrylate-grafted-polypropylene (PP-g-GMA) was used as the compatibilizer to enbance the adhesion between the two polymers and to stabilize the blend morphology. The effect of the viscosity ratio on the morphology of nylon 1010/polypropylene blends was investigated, with primary attention to the phase-inversion behavior and the average particle size of the dispersed phase. The relationship between the mechanical properties and the phase-inversion composition was investigated as well. Investigation of the morphology of the blends by microscopy indicated that the smaller the viscosity ratio (eta(PP)/eta(PA)) the smaller was the polypropylene concentration at which the phase inversion took place and polypropylene became the continuous phase. The compatibilizer induced a sharp reduction of particle size, but did not have a major effect on the phase-inversion point. An improvement :in the mechanical properties was found when nylon 1010 provided the matrix phase. (C) 1996 John Wiley & Sons, Inc.

IN-SITU COMPOSITE - PHENOLPHTHALEIN POLYETHERSULFONE-THERMOTROPIC LIQUID-CRYSTALLINE POLYMER BLENDS

Phase behavior, thermal, theological and mechanical properties plus morphology have been studied for a binary polymer blend. The blend is phenolphthalein polyethersulfone (PES-C) with a thermotropic liquid crystalline polymer (LCP), a condensation copolymer of p-hydroxybenzoic acid with ethylene terephthalate (PHB-PET). It was found that these two polymers form optically isotropic and homogeneous blends by means of a solvent casting method. The homogeneous blends undergo phase separation during heat treatment. However, melt mixed PES-C/PHB-PET blends were heterogeneous based upon DSC and DMA analysis and SEM examination. Addition of LCP in PES-C resulted in a marked reduction of melt viscosity and thus improved processability. Compared to pure PES-C, the charpy impact strength of the blend containing 2.5% LCP increased 2.5 times. Synergistic effects were also observed for the mechanical properties of blends containing < 10% LCP. Particulates, ribbons, and fibrils were found to be the typical morphological units of PHB-PET in the PES-C matrix, which depended upon the concentration of LCP and the processing conditions.

ON THE PHASE-STRUCTURE OF BLENDS OF POLYCARBONATE WITH POLY(ACRYLONITRILE-BUTADIENE-STYRENE)

Polycarbonate (PC) and poly(acrylonitrile-butadiene-styrene) (ABS) was co-extruded at different weight ratios by a single screw extruder. In order to obtain a finer blend, two times extrusion was carried out. In this case, a ''network'' structure with two-continuous phases was observed for the blends with two compositions of PC/ABS, being 80/20 and 70/30. It is found that the blends with these two compositions just have maximum values on the curves of notched Izod impact strength, flexural modulus and flexural strength vs. composition, respectively. This was never observed in previous publications.

CHARACTERIZATION OF BLENDS OF POLYPROPYLENE WITH A SEMIRIGID LIQUID-CRYSTAL COPOLYESTER

Blends with a liquid-crystal polymers (LCP) as one component show, in general, very interesting properties. Reduction of shear visocity and improvement of mechanical properties are very remarkable. High melting temperatures and high costs of the LCP limit the use of these blends. A new class of thermotropic LCPs with flexible spaces, with relatively low melting temperatures, can overcome the first problem. In this work, rheological and mechanical properties of blends of polypropylene with low contents of this LCP are presented. Torque during extrusion and viscosity decrease with LCP content. Elastic modulus is remarkably increased when the LCP phase is oriented.

Induction of diploid gynogenesis in turbot Scophthalmus maximus with left-eyed flounder Paralichthys olivaceus sperm

Turbot Scophthalmus maximus exhibits sexually dimorphic growth, with females growing faster and reaching larger adult sizes than males. Thus, development of techniques for preferentially producing females is necessary to optimize production of these species. In this paper, gynogenetic diploids of turbot were induced by activating egg development with ultraviolet (UV)-irradiated left-eyed flounder Paralichthys olivaceus sperm combined with cold shock to prevent extrusion of the second polar body. The results of UV irradiation experiments showed that survival, motility, and duration of activity of P. olivaceus sperm generally decreased with increase in UV dose. The typical Hertwig's effect was observed after fertilized turbot eggs with UV-irradiated P. olivaceus sperm and the optimal UV dose for gynogenetic haploid production was 36,000 erg mm(-2). At 15 degrees C, appropriate timing of cold shock for retention of the second polar body in turbot eggs was at 6 min after fertilization. Results of different combinations of two shock temperatures (1 or 3 degrees C) and four shock durations (15, 25, 35 or 45 min) at 6 min after fertilization demonstrated that shock of 25 min at 1 degrees C gave the highest production of diploid gynogens (39.58% relative to its diploid control). The results of this study reveal that the use of UV-irradiated P. olivaceus sperm for activation of turbot eggs and cold shock for polar body retention is an effective method to produce gynogenetic offspring.

Mesozoic-Cenozoic tectonic evolution of the Zhuanghai area, Bohai-Bay Basin, east China: the application of balanced cross-sections

The technique of balancing cross-sections, an important method for studying the tectonic history of sedimentary basins, has many applications. It enables one to compile charts for petroleum exploration and development, and growth sections of ancient structures can be restored so that the structural growth history can be studied. In order to study tectonic evolution in the Zhuanghai area of the Bohai-Bay basin, we selected two seismic profiles and compiled two structural growth sections. Based on the two balanced cross-sections, the evolution can be divided into four phases: the Triassic-Middle Jurassic phase, Late Jurassic - Cretaceous phase, Palaeogene extension phase, and Late Palaeogene-to-present phase. The whole area was uplifted during the Triassic-Middle Jurassic phase because of intense extrusion stress related to the Indo-China movement. During the Late Jurassic and Early Cretaceous, intense extension occurred in east China, and the whole area rifted, leading to the deposition of a thick sedimentary sequence. In the Late Cretaceous, the area suffered uplift and compression associated with the sinistral strike slip of the Tanlu fault. In the Palaeogene, a rifting basin developed in the area. Finally, it became stable and was placed in its present position by dextral strike-slip motion. In addition, some problems associated with compiling balanced cross-sections are discussed.