Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Environmental assessment of low speed policies for motor vehicle mobility in city centres

streets in local residential areas in large cities, real traffic tests for pollutant emissions and fuel consumption have been carried out in Madrid city centre. Emission concentration and car activity were simultaneously measured by a Portable Emissions Measurement System. Real life tests carried out at different times and on different days were performed with a turbo-diesel engine light vehicle equipped with an oxidizer catalyst and using different driving styles with a previously trained driver. The results show that by reducing the speed limit from 50 km h-1 to 30 km h-1, using a normal driving style, the time taken for a given trip does not increase, but fuel consumption and NOx, CO and PM emissions are clearly reduced. Therefore, the main conclusion of this work is that reducing the speed limit in some narrow streets in residential and commercial areas or in a city not only increases pedestrian safety, but also contributes to reducing the environmental impact of motor vehicles and reducing fuel consumption. In addition, there is also a reduction in the greenhouse gas emissions resulting from the combustion of the fuel.

Optimización de la metodología de contratación de carbones térmicos con destino a la generación eléctrica

En los últimos quince años se ha producido una liberalización de los mercados eléctricos en los distintos países de ámbito occidental que ha ido acompañado de un incremento por la preocupación por la incidencia de las distintas tecnologías de generación en el entorno medioambiental. Ello se ha traducido en la aparición de un marco regulatorio más restrictivo sobre las tecnologías de generación fósiles, con mayor incidencia en las derivadas de productos petrolíferos y carbón. A nivel mundial han ido apareciendo cambios normativos relativos a las emisiones de distintos elementos contaminantes (CO2, SO2, NOx…), que hacen que en particular las centrales térmicas de carbón vean muy afectadas su rentabilidad y funcionamiento. Esta situación ha supuesto que la tecnología de generación eléctrica con carbón haya avanzado considerablemente en los últimos años (calderas supercríticas, sistemas de desulfuración, gasificación del carbón…). No obstante, el desarrollo de la generación con energías renovables, la generación con gas mediante centrales de ciclo combinado y la opinión social relativa a la generación con carbón, principalmente en Europa, suponen un serio obstáculo a la generación con carbón. Por consiguiente, se hace necesario buscar vías para optimizar la competitividad de las centrales de carbón y el camino más razonable es mejorar el margen esperado de estas plantas y en particular el coste de adquisición del carbón. Ello se hace aún más importante por el hecho de existir numerosas centrales de carbón y un elevado número de nuevos proyectos constructivos de centrales de carbón en países asiáticos. Por consiguiente, el objeto de la presente tesis doctoral se centra en definir una metodología para optimizar la compra de carbón, desde el punto de vista económico y técnico, con destino a su consumo en una central térmica, con ello reducir el coste del carbón consumido y mejorar su competitividad. También se enfoca a determinar que herramientas pueden ser utilizadas para optimizar la gestión del carbón después de su compra y con ello abrir la posibilidad de obtener márgenes adicionales para dicho carbón. De acuerdo con este objetivo, el autor de la presente Tesis Doctoral realiza tres aportaciones novedosas en el ámbito de la contratación de carbón térmico y su optimización posterior: - Evaluación de carbones para su adquisición considerando el efecto de la calidad del carbón en el coste de generación asociado a cada carbón ofertado. - Creación, desarrollo, implantación y utilización de una potente herramienta de planificación de Combustibles. Esta herramienta, está diseñada con el objeto de determinar la solución económica óptima de aprovisionamientos, consumos y niveles de existencias para un parque de generación con centrales de carbón y fuelóleo. - La extensión de una metodología contractual habitual en el mercado spot de Gas Natural Licuado, a la contratación spot de Carbón de Importación. Esta se basa en el desarrollo de Acuerdos Marcos de Compra/Venta de carbón, que por su flexibilidad permitan obtener resultados económicos adicionales después de la compra de un carbón. Abstract In the last fifteen years, a liberalization of the electrical markets has occurred in the western countries. This process has been accompanied by an increasing concern of the impact of the different generation technologies towards the environment. This has motivated a regulated framework restricting the use of fossil fuels, impacting a great deal in coal and oil based products. Worldwide, new legal changes have been arising related to the emissions of the different pollutants (CO2, SO2, NOx…). These changes have had a deep impact in the feasibility, profit and running of coal fired power plants. This situation has motivated the coal electrical generation technologies to move forward in an important way in the last few years (supercritical furnaces, desulphuration plants, coal gasification…). Nevertheless, the development of the renewable generation, the gas combined cycle generation and the social opinion related to the coal electrical generation, mainly in Europe, have created a serious obstacle to the generation of electricity by coal. Therefore it is necessary to look for new paths in order to optimize the competitiveness of the coal fired power plants and the most reasonable way is to improve the expected margin of these plants and particularly the coal purchase cost. All of the above needs to be taken into context with the large number of existing coal fired power plants and an important number of new projects in Asian countries. Therefore, the goal of the current doctoral dissertation is focused to define a methodology to be considered in order to optimize the coal purchase, from an economical and a technical point of view. This coal, destined for power plant consumption, permits the reduction of consumption coal cost and improves the plant’s competitiveness. This document is also focused to define what tools we can use to optimize the coal management after deal closing and therefore open the possibility to get further margins. According to this goal, the author of this doctoral dissertation provides three important new ideas in the ambit of contracting steam coal and the posterior optimization: - Evaluation of coal purchases, considering the effect of coal quality on the cost of generation associated with each type of coal offered. - The creation, development, deployment and use of a strong planning tool of fuels. This tool is designed for the purpose of determining the optimal economic solution of fuel supply, consumption and stock levels for a power generation portfolio using coal and fuel oil fired power plants. - The application of a common contractual methodology in the spot market of Liquid Natural Gas, for the contracting spot imported coal. This is based on the development of Framework Agreements for the Purchasing / Sale of coal, which because of its flexibility allows for the gain of additional financial results after the purchase of coal.

Comparasion of road traffic emission models in Madrid (Spain)

Many cities in Europe have difficulties to meet the air quality standards set by the European legislation, most particularly the annual mean Limit Value for NO2. Road transport is often the main source of air pollution in urban areas and therefore, there is an increasing need to estimate current and future traffic emissions as accurately as possible. As a consequence, a number of specific emission models and emission factors databases have been developed recently. They present important methodological differences and may result in largely diverging emission figures and thus may lead to alternative policy recommendations. This study compares two approaches to estimate road traffic emissions in Madrid (Spain): the COmputer Programme to calculate Emissions from Road Transport (COPERT4 v.8.1) and the Handbook Emission Factors for Road Transport (HBEFA v.3.1), representative of the ‘average-speed’ and ‘traffic situation’ model types respectively. The input information (e.g. fleet composition, vehicle kilometres travelled, traffic intensity, road type, etc.) was provided by the traffic model developed by the Madrid City Council along with observations from field campaigns. Hourly emissions were computed for nearly 15 000 road segments distributed in 9 management areas covering the Madrid city and surroundings. Total annual NOX emissions predicted by HBEFA were a 21% higher than those of COPERT. The discrepancies for NO2 were lower (13%) since resulting average NO2/NOX ratios are lower for HBEFA. The larger differences are related to diesel vehicle emissions under “stop & go” traffic conditions, very common in distributor/secondary roads of the Madrid metropolitan area. In order to understand the representativeness of these results, the resulting emissions were integrated in an urban scale inventory used to drive mesoscale air quality simulations with the Community Multiscale Air Quality (CMAQ) modelling system (1 km2 resolution). Modelled NO2 concentrations were compared with observations through a series of statistics. Although there are no remarkable differences between both model runs, the results suggest that HBEFA may overestimate traffic emissions. However, the results are strongly influenced by methodological issues and limitations of the traffic model. This study was useful to provide a first alternative estimate to the official emission inventory in Madrid and to identify the main features of the traffic model that should be improved to support the application of an emission system based on “real world” emission factors.

Kinetics of CO2 absorption into aqueous solutions in CO2

This research has been performed to emphasize about the problem known as ?climate changes? occurring due to the greenhouse gases emissions (Carbon dioxide (CO2), Methane (CH4),Nitrogen oxides (NOx), Ozone (O3), Chlorofluorocarbons (artificial). Specially, the project will be focused on the CO2 emissions produced mainly from the fossil fuels burning in power plants and other kind of industrial processes. To understand how important the global is warming and therefore the climate change, both the increase of emissions and the evolution of those will be studied in this project drawing conclusions about its effect. The Kyoto Protocol, the most important agreement internationally, signed by a great majority of the industrialized and developed countries, which try to limit the CO2 emissions to the atmosphere, will be cited in this project. Taking into account the effects of global warming and applying the international legislation on emissions of greenhouse gases, a number of measures will be exposed, where the CO2 capture will be studied deeply. Three different kind of CO2 capture technologies will be studied, drawing the conclusion that the post-combustion capture, in particular by amine chemical absorption, is the most efficient one.

Gasification technology assessment of sterile coal to clean electrical power generation.

Sterile coal is a low-value residue associated to the coal extraction and mining activity. According to the type and origin of the coal bed configuration, sterile coal production can mainly vary on quantity, calorific value and presence of sulphur compounds. In addition, the potential availability of sterile coal within Spain is apparently high and its contribution to the local power generation would be of interest playing a significant role. The proposed study evaluates the availability and deployment of gasification technologies to drive clean electricity generation from waste coal and sterile rock coal, incorporating greenhouse gas emission mitigation systems, like CO2, H2S and NOx removal systems. It establishes the target facility and its conceptual basic design proposal. The syngas obtained after the gasification of sterile coal is processed through specific conditioning units before entering into the combustion chamber of a gas turbine. Flue gas leaving the gas turbine is ducted to a heat recovery steam generation boiler; the steam produced within the boilerdrives a steam turbine. The target facility resembles a singular Integrated Gasification in Combined Cycle (IGCC) power station. The evaluation of the conceptual basic design according to the power output set for a maximum sterile contribution, established that rates over 95% H2S and 90% CO2 removal can be achieved. Noticeable decrease of NOx compounds can be also achieved by the use of commercial technology. A techno-economic approach of the conceptual basic design is made evaluating the integration of potential unitsand their implementation within the target facility aiming toachieve clean power generation. The criterion to be compliant with the most restrictive regulation regarding environmental emissions is setting to carry out this analysis.

How lowering speed limits in an urban highway affects traffics performance and emissions: the case of Madrid M-30 ring-road

The city of Madrid keeps not meeting the GHG and air pollutant limits set by the European legislation. A broad range of strategies have being taken into account to reduce both types of emissions; however traffic management meas ures are usually consigned to the sidelines. In 2004, Madrid City Council launched a plan to re-design its inner ring-road supported by a socioeconomic study that evaluated the environmental and operational benefits of the project. For safety reasons the planned speed limit for the tunnel section was finally reduced from 90km/h to 70km/h. Using a Macroscopic Traffic Model and the European Air Pollutant and Emissions Inventory Guidebook (EMEP/EEA), this paper examines the environmental and traffic performance consequences of this decision. Results support the thesis that reduced speed limits leads to GHG and air pollution reductions in the area affected by the measure without substantially altering traffic performance. The implementation of the new speed limit policy brings about a 15% and 16% reduction in both CO2 and NOx emissions respectively. Emissions’ reduction during off-peak hours is larger than during peak hours.

Despacho económico ambiental de unidades térmicas de carbón

El objetivo del presente proyecto es el despacho económico-ambiental de unidades térmicas de carbón con respecto a la minimización de sus costes horarios o de sus emisiones de óxidos de nitrógeno (NOX), según convenga. Se han estudiado tanto las curvas de costes de generación como las de emisión de óxidos de nitrógeno para cinco unidades tipo de carbón para poder llevar a cabo el proyecto. Se modelizaron las curvas de emisión de óxidos de nitrógeno para las cinco unidades estudiadas mediante la simulación de la combustión del carbón en caldera con el software ASPEN PLUS®, y las curvas de costes con datos proporcionados en la publicación “Las centrales termoeléctricas: Consumos marginales, Consumos medios y costes de arranque de grupos de carbón” y otra bibliografía, para su posterior aplicación en el despacho, desarrollado en Excel y con el uso de su lenguaje de programación, VBA, para escribir un código que automatice la elección a tomar entre todas las posibilidades. Analizando tres posibles casos de generación térmica con carbón, se ha llevado a cabo el despacho económico-ambiental de las cinco unidades implicadas, con todas sus posibles combinaciones (apagado-encendido), obteniendo en cada caso lo que parece ser la manera más económica o ambiental, según convenga, de generar la potencia demandada en cada momento. ABSTRACT The aim of this project is the economic-environmental dispatch of thermal coal power plants to minimize the hourly costs of generation or the nitrogen oxides (NOX) emissions as appropriate. It have been studied both generation cost curves as nitrogen oxides emissions curves for five examples of coal power plants to carry out the project. Nitrogen oxides emissions curves were modeled for the five coal power plants simulating the coal combustion in the boiler with ASPEN PLUS® software, and generation cost curves with data provided in the publication “Las centrales termoeléctricas: Consumos marginales, Consumos medios y costes de arranque de grupos de carbón” and other publications, to be used later in the dispatch, developed in Excel, using the VBA code, to write a code that automatize the correct election between all the generation possibilities. Analizing three possible cases of thermal generation with coal, economic-environmental dispatch for the five implied power plants has been done, with all the possible combinations (generating or no generating), obtaining, in each case, the most economically or environmentally way, as appropriate, to generate the demanded power in each moment.