High temperature, low cycle fatigue of a hybrid particulate/fiber aluminum metal-matrix composite

The effect of shot particles on the high temperature, low cycle fatigue of a hybrid fiber/particulate metal-matrix composite (MMC) was studied. Two hybrid composites with the general composition A356/35%SiC particle/5%Fiber (one without shot) were tested. It was found that shot particles acting as stress concentrators had little effect on the fatigue performance. It appears that fibers with a high silica content were more likely to debond from the matrix. Final failure of the composite was found to occur preferentially in the matrix. SiC particles fracture progressively during fatigue testing, leading to higher stress in the matrix, and final failure by matrix overload. A continuum mechanics based model was developed to predict failure in fatigue based on the tensile properties of the matrix and particles. By accounting for matrix yielding and recovery, composite creep and particle strength distribution, failure of the composite was predicted.

Characterization of thermal and mechanical properties of polypropylene-based composites for fuel cell bipolar plates and development of educational tools in hydrogen and fuel cell technologies

In this project we developed conductive thermoplastic resins by adding varying amounts of three different carbon fillers: carbon black (CB), synthetic graphite (SG) and multi-walled carbon nanotubes (CNT) to a polypropylene matrix for application as fuel cell bipolar plates. This component of fuel cells provides mechanical support to the stack, circulates the gases that participate in the electrochemical reaction within the fuel cell and allows for removal of the excess heat from the system. The materials fabricated in this work were tested to determine their mechanical and thermal properties. These materials were produced by adding varying amounts of single carbon fillers to a polypropylene matrix (2.5 to 15 wt.% Ketjenblack EC-600 JD carbon black, 10 to 80 wt.% Asbury Carbon's Thermocarb TC-300 synthetic graphite, and 2.5 to 15 wt.% of Hyperion Catalysis International's FIBRILTM multi-walled carbon nanotubes) In addition, composite materials containing combinations of these three fillers were produced. The thermal conductivity results showed an increase in both through-plane and in-plane thermal conductivities, with the largest increase observed for synthetic graphite. The Department of Energy (DOE) had previously set a thermal conductivity goal of 20 W/m·K, which was surpassed by formulations containing 75 wt.% and 80 wt.% SG, yielding in-plane thermal conductivity values of 24.4 W/m·K and 33.6 W/m·K, respectively. In addition, composites containing 2.5 wt.% CB, 65 wt.% SG, and 6 wt.% CNT in PP had an in–plane thermal conductivity of 37 W/m·K. Flexural and tensile tests were conducted. All composite formulations exceeded the flexural strength target of 25 MPa set by DOE. The tensile and flexural modulus of the composites increased with higher concentration of carbon fillers. Carbon black and synthetic graphite caused a decrease in the tensile and flexural strengths of the composites. However, carbon nanotubes increased the composite tensile and flexural strengths. Mathematical models were applied to estimate through-plane and in-plane thermal conductivities of single and multiple filler formulations, and tensile modulus of single-filler formulations. For thermal conductivity, Nielsen's model yielded accurate thermal conductivity values when compared to experimental results obtained through the Flash method. For prediction of tensile modulus Nielsen's model yielded the smallest error between the predicted and experimental values. The second part of this project consisted of the development of a curriculum in Fuel Cell and Hydrogen Technologies to address different educational barriers identified by the Department of Energy. By the creation of new courses and enterprise programs in the areas of fuel cells and the use of hydrogen as an energy carrier, we introduced engineering students to the new technologies, policies and challenges present with this alternative energy. Feedback provided by students participating in these courses and enterprise programs indicate positive acceptance of the different educational tools. Results obtained from a survey applied to students after participating in these courses showed an increase in the knowledge and awareness of energy fundamentals, which indicates the modules developed in this project are effective in introducing students to alternative energy sources.

Nanomechanics of cellulose crystals and cellulose-based polymer composites

Cellulose-polymer composites have potential applications in aerospace and transportation areas where lightweight materials with high mechanical properties are needed. In addition, these economical and biodegradable composites have been shown to be useful as polymer electrolytes, packaging structures, optoelectronic devices, and medical implants such as wound dressing and bone scaffolds. In spite of the above mentioned advantages and potential applications, due to the difficulties associated with synthesis and processing techniques, application of cellulose crystals (micro and nano sized) for preparation of new composite systems is limited. Cellulose is hydrophilic and polar as opposed to most of common thermoplastics, which are non-polar. This results in complications in addition of cellulose crystals to polymer matrices, and as a result in achieving sufficient dispersion levels, which directly affects the mechanical properties of the composites. As in other composite materials, the properties of cellulose-polymer composites depend on the volume fraction and the properties of individual phases (the reinforcement and the polymer matrix), the dispersion quality of the reinforcement through the matrix and the interaction between CNCs themselves and CNC and the matrix (interphase). In order to develop economical cellulose-polymer composites with superior qualities, the properties of individual cellulose crystals, as well as the effect of dispersion of reinforcements and the interphase on the properties of the final composites should be understood. In this research, the mechanical properties of CNC polymer composites were characterized at the macro and nano scales. A direct correlation was made between: Dispersion quality and macro-mechanical properties Nanomechanical properties at the surface and tensile properties CNC diameter and interphase thickness Lastly, individual CNCs from different sources were characterized and for the first time size-scale effect on their nanomechanical properties were reported. Then the effect of CNC surface modification on the mechanical properties was studied and correlated to the crystalline structure of these materials.

COMPUTATIONAL STUDY OF MICROSTRUCTURE-PROPERTYMECHANISM RELATIONS IN FERROIC COMPOSITES

Ferroic materials, as notable members of smart materials, have been widely used in applications that perform sensing, actuation and control. The macroscopic property change of ferroic materials may become remarkably large during ferroic phase transition, leading to the fact that the macroscopic properties can be tuned by carefully applying a suitable external field (electric, magnetic, stress). To obtain an enhancement in physical and/or mechanical properties, different kinds of ferroic composites have been fabricated. The properties of a ferroic composite are determined not only by the properties and relative amounts of the constituent phases, but also by the microstructure of individual phase such as the phase connectivity, phase size, shape and spatial arrangement. This dissertation mainly focuses on the computational study of microstructure – property – mechanism relations in two representative ferroic composites, i.e., two-phase particulate magnetoelectric (ME) composite and polymer matrix ferroelectric composite. The former is a great example of ferroic composite exhibiting a new property and functionality that neither of the constituent phases possesses individually. The latter well represents the kind of ferroic composites having property combinations that are better than the existing materials. Phase field modeling was employed as the computing tool, and the required models for ferroic composites were developed based on existing models for monolithic materials. Extensive computational simulations were performed to investigate the microstructure-property relations and the underlying mechanism in ferroic composites. In particulate, it is found that for ME composite 0-3 connectivity (isolated magnetostrictive phase) is necessary to exhibit ME effect, and small but finite electrical conductivity of isolated magnetic phase can beneficially enhance ME effect. It is revealed that longitudinal and transverse ME coefficients of isotropic 0-3 particulate composites can be effectively tailored by controlling magnetic domain structures without resort to anisotropic two-phase microstructures. Simulations also show that the macroscopic properties of the ferroelectricpolymer composites critically depend on the ferroelectric phase connectivity while are not sensitive to the sizes and internal grain structures of the ceramic particles. Texturing is found critical to exploit the paraelectric«ferroelectric phase transition and nonlinear polarization behavior in paraelectric polycrystal and its polymer matrix composite. Additionally, a Diffuse Interface Field model was developed to simulate packing and motion in liquid phase which is promising for studying the fabrication of particulatepolymer composites.

A Study of Metallic Eutectics

All of the metals have definite melting points. When a metal is heated above the melting point, it exists as a liquid. Now if the melt is allowed to cool, it will solidify when a temperature corresponding to the melting point is reached. However, if one metal is added to another metal, both of which are mutually soluble in the liquid state, a certain effect can be noted. The melt will not solid­ify when the melting point of the pure metal is reached, but will freeze at a lower temperature.

Intraply fracture of fiber-reinforced composites: microscopic mechanisms and modeling

The fracture behavior parallel to the fibers of an E-glass/epoxy unidirectional laminate was studied by means of three-point tests on notched beams. Selected tests were carried out within a scanning electron microscope to ascertain the damage and fracture micromechanisms upon loading. The mechanical behavior of the notched beam was simulated within the framework of the embedded cell model, in which the actual composite microstructure was resolved in front of the notch tip. In addition, matrix and interface properties were independently measured in situ using a nanoindentor. The numerical simulations very accurately predicted the macroscopic response of the composite as well as the damage development and crack growth in front of the notch tip, demonstrating the ability of the embedded cell approach to simulate the fracture behavior of heterogeneous materials. Finally, this methodology was exploited to ascertain the influence of matrix and interface properties on the intraply toughness.

Application of digital image correlation at the microscale in fiber-reinforced composites

Digital image correlation (DIC) is applied to analyzing the deformation mechanisms under transverse compression in a fiber-reinforced composite. To this end, compression tests in a direction perpendicular to the fibers were carried out inside a scanning electron microscope and secondary electron images obtained at different magnifications during the test. Optimum DIC parameters to resolve the displacement and strain field were computed from numerical simulations of a model composite and they were applied to micrographs obtained at different magnifications (250_, 2000_, and 6000_). It is shown that DIC of low-magnification micrographs was able to capture the long range fluctuations in strain due to the presence of matrix-rich and fiber-rich zones, responsible for the onset of damage. At higher magnification, the strain fields obtained with DIC qualitatively reproduce the non-homogeneous deformation pattern due to the presence of stiff fibers dispersed in a compliant matrix and provide accurate results of the average composite strain. However, comparison with finite element simulations revealed that DIC was not able to accurately capture the average strain in each phase.

Highly conductive coatings of carbon black/silica composites obtained by a sol-gel process

Conductive submicronic coatings of carbon black (CB)/silica composites have been prepared by a sol-gel process and deposited by spray-coating on glazed porcelain tiles. Stable CB dispersions with surfactant were rheologically characterized to determine the optimum CB-surfactant ratio. The composites were analyzed by Differential Thermal and Thermogravimetric Analysis and Hg-Porosimetry. Thin coatings were thermally treated in the temperature range of 300-500degC in air atmosphere. The microstructure of the coatings was determined by scanning electron microscopy and the structure evaluated by confocal Raman spectroscopy. The electrical characterization of the samples was carried out using dc intensity-voltage curves. The coatings exhibit good adhesion, high density and homogeneous distribution of the conductive filler (CB) in the insulate matrix (silica) that protects against the thermal degradation of the CB nanoparticles during the sintering process. As consequence, the composite coatings show the lowest resistivity values for CB-based films reported in the literature, with values of ~7times10 -5Omegam.

Enhancing the thermomechanical behaviour of poly(phenylene sulphide) based composites via incorporation of covalently grafted carbon nanotubes

The thermal and thermomechanical properties of poly(phenylene sulphide) (PPS) based nanocomposites incorporating a polymer derivative covalently anchored onto single-walled carbon nanotubes (SWCNTs) were investigated. The grafted fillers acted as nucleating agents, increasing the crystallization temperature and degree of crystallinity of the matrix. They also enhanced its thermal stability, flame retardancy, glass transition (Tg) and heat deflection temperatures while reduced the coefficient of thermal expansion at temperatures below Tg. A strong rise in the thermal conductivity, Young?s modulus and tensile strength was found with increasing filler loading both in the glassy and rubbery states. All these outstanding improvements are ascribed to strong matrix-filler interfacial interactions combined with a compatibilization effect that results in very homogeneous SWCNT dispersion. The results herein offer useful insights towards the development of engineering thermoplastic/CNT nanocomposites for high-temperature applications.

Polypropylene/glass fiber hierarchical composites incorporating inorganic fullerene-like nanoparticles for advanced technological applications

Novel isotactic polypropylene (iPP)/glass fiber (GF) laminates reinforced with inorganic fullerene-like tungsten disulfide (IF-WS2) nanoparticles as environmentally friendly fillers have been successfully fabricated by simple melt-blending and fiber impregnation in a hot-press without the addition of any compatibilizer. The influence of IF-WS2 concentration on the morphology, viscosity. and thermal and mechanical behavior of the hierarchical composites has been investigated. Results revealed an unprecedented 62 °C increase in the degradation temperature of iPP/GF upon addition of only 4.0 wt % IF-WS2. The coexistence of both micro- and nanoscale fillers resulted in synergistic effects on enhancing the stiffness, strength, crystallinity, thermal stability, glass transition (Tg) and heat distortion temperature (HDT) of the matrix. The approach used in this work is an efficient, versatile, scalable and economic strategy to improve the mechanical and thermal behavior of GF-reinforced thermoplastics with a view to extend their use in advanced technological applications. This new type of composite materials shows great potential to improve the efficiency and sustainability of many forms of transport.

Multiscale Modeling of Composites: Toward Virtual Testing ... and Beyond

Recent developments in the area of multiscale modeling of fiber-reinforced polymers are presented. The overall strategy takes advantage of the separa-tion of length scales between different entities (ply, laminate, and component) found in composite structures. This allows us to carry out multiscale modeling by computing the properties of one entity (e.g., individual plies) at the relevant length scale, homogenizing the results into a constitutive model, and passing this information to the next length scale to determine the mechanical behavior of the larger entity (e.g., laminate). As a result, high-fidelity numerical sim-ulations of the mechanical behavior of composite coupons and small compo-nents are nowadays feasible starting from the matrix, fiber, and interface properties and spatial distribution. Finally, the roadmap is outlined for extending the current strategy to include functional properties and processing into the simulation scheme.

Mechanical behavior and failure micromechanisms of hybrid 3D woven composites in tension

The deformation and failure micromechanisms of a hybrid 3D woven composite were studied in tension. Plain and open-hole composite coupons were tested in tension until failure in the fill and warp directions, as well as fiber tows extracted from the dry fabric and impregnated with the matrix. The macroscopic evolution of damage in the composite coupons was assessed by means of periodic unloading–reloading (to obtain the elastic modulus and the residual strain), whereas the microscopic mechanism were established by means of X-ray computed microtomography. To this end, specimens were periodically removed from the mechanical testing machine and infiltrated with ZnI-containing liquid to assess the main damage modes as a function of the applied strain. The experimental observations and the predictions of an isostrain model were used to understand the key factors controlling the elastic modulus, strength and notch sensitivity of hybrid 3D woven composites in tension. It was found that the full contribution of the glass fibers to the composite strength was not employed, due to the premature fracture of the carbon fibers, but their presence increased the fracture strain and the energy dissipated during fracture. Thus, hybridization of the 3D woven composite led to a notch-insensitive behavior as demonstrated by open-hole tests

Automatic quantification of matrix cracking and fiber rotation by X-ray computed tomography in shear-deformed carbon fiber-reinforced laminates

The deformation and damage mechanisms of carbon fiber-reinforced epoxy laminates deformed in shear were studied by means of X-ray computed tomography. In particular, the evolution of matrix cracking, interply delamination and fiber rotation was ascertained as a function of the applied strain. In order to provide quantitative information, an algorithm was developed to automatically determine the crack density and the fiber orientation from the tomograms. The investigation provided new insights about the complex interaction between the different damage mechanisms (i.e. matrix cracking and interply delamination) as a function of the applied strain, ply thickness and ply location within the laminate as well as quantitative data about the evolution of matrix cracking and fiber rotation during deformation

A numerical study of the influence of microvoids in the transverse mechanical response of unidirectional composites

The effect of porosity on the transverse mechanical properties of unidirectional fiber-reinforced composites is studied by means of computational micromechanics. The composite behavior is simulated by the finite element analysis of a representative volume element of the composite microstructure in which the random distribution of fibers and the voids are explicitly included. Two types of voids – interfiber voids and matrix voids – were included in the microstructure and the actual damage mechanisms in the composite, namely matrix and interface failure, were accounted for. It was found that porosity (in the range 1–5%) led to a large reduction in the transverse strength and the influence of both types of voids in the onset and propagation of damage throughout the microstructure was studied under transverse tension and compression. Finally, the failure locus of the composite lamina under transverse tension/compression and out-of-plane shear was obtained by means of computational micromechanics and compared with the predictions of Puck’s model and with experimental data available in the literature. The results show that the strength of composites is significantly reduced by the presence of voids

Recubrimientos autolubricantes cuasicristalinos tipo composite depositados mediante proyección térmica para aplicaciones espaciales y de alta temperatura

Los recubrimientos lubricantes sólidos son requeridos para reducir la fricción y prevenir el desgaste en componentes que operan a altas temperaturas o en vacío (vehículos espaciales, industria química, motores diésel, turbinas aeronáuticas y de generación de energía…). Los lubricantes líquidos pierden sus características cuando las condiciones de presión, temperatura o ambientales son severas (oxidación, inestabilidad térmica, volatilidad,…), por ejemplo los aceites minerales convencionales se descomponen a temperaturas próximas a 200 ºC. Por tanto, la única manera de poder conseguir una adecuada lubricación a temperaturas extremas es por medio de sólidos, que cada vez más, se aplican en forma de recubrimientos. Estos recubrimientos podrían ser empleados en componentes de vehículos espaciales reutilizables, donde se pueden alcanzar, en la reentrada en la atmósfera, temperaturas de 700 ºC (bisagras, rodamientos, articulaciones y zonas de sellado en las superficies de control, y rodamientos de las turbobombas y las cajas de engranajes). Dichos recubrimientos también deberían ser capaces de proporcionar una lubricación efectiva a bajas temperaturas para las operaciones en tierra, para las operaciones de arranque en frío, incluso en el espacio. El conjunto de requisitos que tendrían que satisfacer las capas tribológicas relacionadas con estas condiciones extremas es muy diverso, lo que hace que el concepto de capas tipo composite (aquéllas constituidas por varios componentes) sea, en principio, muy adecuado para estas aplicaciones. Recubrimientos composite proyectados térmicamente constituidos por una matriz dura y conteniendo lubricantes sólidos pueden ser una buena solución desde el punto de vista tribológico. El “Lewis Research Centre” de la NASA ha estado desarrollando recubrimientos autolubricantes tipo composite, constituidos por la combinación de materiales duros como el carburo de cromo, junto con lubricantes sólidos como plata o la eutéctica de fluoruros de calcio y bario, en una matriz de NiCr, para su uso en aplicaciones terrestres a alta temperatura. Estos recubrimientos han sido aplicados mediante proyección térmica, siendo denominados como series PS100, PS200, PS300 y PS400, reduciendo de forma significativa el coeficiente de fricción y mejorando la resistencia al desgaste en un amplio margen de temperaturas. Otra nueva familia de materiales con comportamiento tribológico prometedor son las aleaciones cuasicristalinas (QC). Presentan características muy atractivas: alta dureza, baja fricción, alto límite elástico de compresión... Son muy frágiles como materiales másicos, por lo que se intentan aplicar en forma de recubrimientos. Se pueden depositar mediante proyección térmica. Algunos de estos materiales cuasicristalinos, como AlCoFeCr, poseen coeficientes de dilatación próximos al de los materiales metálicos, alta estabilidad térmica, baja conductividad térmica y una elevada resistencia a la oxidación y a la corrosión en caliente. En esta tesis se han desarrollado recubrimientos tipo composite conteniendo cuasicristales como componente antidesgaste, NiCr como componente tenaz, y Ag y la eutéctica de BaF2-CaF2, como lubricantes sólidos. Estos recubrimientos han sido depositados con diferentes composiciones (denominadas TH100, TH103, TH200, TH400, TH600…) mediante distintos procesos de proyección térmica: plasma en aire (PS), plasma en baja presión (LPPS) y combustión a alta velocidad (HVOF). Los recubrimientos se han generado sobre el sustrato X-750, una superaleación base níquel, endurecible por precipitación, con muy buena resistencia mecánica y a la oxidación hasta temperaturas de 870 ºC y, además, es empleada en aplicaciones aeroespaciales e industriales. Los recubrimientos han sido caracterizados microestructuralmente en INTA (Instituto Nacional de Técnica Aeroespacial), mediante SEM-EDS (Scanning Electronic Microscopy-Energy Dispersive Spectroscopy) y XRD (X-Ray Diffraction), y tribológicamente mediante medidas de microdureza y ensayos en tribómetro POD (Pin On Disc) para determinar los coeficientes de fricción y de desgaste. Los recubrimientos han sido ensayados tribológicamente a alta temperatura en INTA y en vacío en AMTTARC (Aerospace and Space Materials Technology Testhouse – Austrian Research Centres), en Seibersdorf (Austria). Se ha estudiado la influencia de la carga normal aplicada, la velocidad lineal y el material del pin. De entre las diferentes series de recubrimientos cuasicristalinos tipo composite desarrolladas, dos de ellas, TH100 y TH103 han presentado una excelente calidad microestructural (baja porosidad, distribución uniforme de fases…) y se han mostrado como excelentes recubrimientos antidesgaste. Sin embargo, estas capas presentan un pobre comportamiento como autolubricantes a temperatura ambiente, aunque mejoran mucho a alta temperatura o en vacío. Los resultados del trabajo presentado en esta tesis han proporcionado nuevo conocimiento respecto al comportamiento tribológico de recubrimientos autolubricantes cuasicristalinos tipo composite depositados por proyección térmica. Sin embargo, dichos resultados, aunque son muy prometedores, no han puesto de manifiesto el adecuado comportamiento autolubricante que se pretendía y, además, como ocurre en cualquier trabajo de investigación, durante el desarrollo del mismo siempre aparecen nuevas dudas por resolver. Se proponen nuevas líneas de trabajo futuro que complementen los resultados obtenidos y que puedan encaminar hacia la obtención de un recubrimiento que mejore su comportamiento autolubricante. ABSTRACT Solid lubricant coatings are required to reduce friction and prevent wear in components that operate at high temperatures or under vacuum (space vehicles, chemical industry, diesel engines, power generation turbines and aeronautical turbines, for instance). In these cases neither greases nor liquid lubricants can be employed and the only practicable approach to lubrication in such conditions is by means of solids. These are increasingly applied in the form of coatings which should exhibit low shear strength, whilst maintaining their chemical stability at extremes temperatures and in the space environment. In the space field, these coatings would be employed in re-usable space plane applications, such as elevon hinges, where temperatures of 700 ºC are reached during re-entry into the Earth’s atmosphere. These coatings should also be capable of providing effective lubrication at lower temperatures since “cold start” operation may be necessary, even in the space environment. The diverse and sometimes conflictive requirements in high temperature and space-related tribological coatings make the concept of composite coatings highly suitable for these applications. Thermal-sprayed composites containing solid lubricants in a hard matrix perform well tribologically. NASA‘s Lewis Research Centre had developed self-lubricating composite coatings for terrestrial use, comprising hard materials like chromium carbide as well as solid lubricant additives such as silver and BaF2-CaF2 eutectic on a Ni-Cr matrix. These coatings series, named PS100, PS200, PS300 and PS400, are applied by thermal spray and significantly reduce friction coefficients, improving wear resistance over a wide temperature range. Quasicrystalline alloys (QC) constitute a new family of materials with promising tribological behaviour. Some QC materials exhibit a combination of adequate antifriction properties: low friction coefficient, high hardness and high yield strength under compression, and can be easily produced as coatings on top of metallic and non-metallic materials. Among these QC alloys, AlCoFeCr has high hardness (700 HV0.1), a thermal expansion coefficient close to that of metals, high thermal stability, low thermal conductivity and good oxidation and hot corrosion resistance. However most QC materials have the disadvantage of being very brittle. In order to take advantage of the excellent tribological properties of QCs, thick composite lubricant coatings were prepared containing them as the hard phase for wear resistance, Ag and BaF2-CaF2 eutectic as lubricating materials and NiCr as the tough component. These coatings were deposited in different composition mixtures (named TH100, TH103, TH200, TH400, TH600…) by different thermal spray processes: air plasma spray (PS), low pressure plasma spray (LPPS) and high velocity oxy-fuel (HVOF), on X-750 substrates. X-750 is an age-hardenable nickel-base superalloy with very good strength and a good resistance to oxidising combustion gas environments at temperatures up to about 870 ºC and it is widely used in aerospace and industrial applications. Coatings have been characterized microstructurally, at INTA (National Institute for Aerospace Technology), by means of SEM-EDS (Scanning Electronic Microscopy- Energy Dispersive Spectroscopy) and XRD (X-Ray Diffraction), and tribologically by microhardness measurements and pin-on-disc testing to determine friction coefficients as well as wear resistance. The coatings were tested tribologically at high temperature at INTA and under vacuum at AMTT-ARC (Aerospace and Space Materials Technology Testhouse – Austrian Research Centres), in Seibersdorf (Austria). Different loads, linear speeds and pin materials were studied. TH100 and TH103 QC alloy matrix composite coatings were deposited by HVOF with excellent microstructural quality (low porosity, uniform phase distribution) and showed to be excellent wear resistant coatings. However these QC alloy matrix composite coatings are poor as a self-lubricant at room temperature but much better at high temperature or in vacuum. The results from the work performed within the scope of this thesis have provided new knowledge concerning the tribological behavior of self-lubricating quasicrystalline composite coatings deposited by thermal spraying. Although these results are very promising, they have not shown an adequate self-lubricating behavior as was intended, and also, as in any research, the results have in addition raised new questions. Future work is suggested to complement the results of this thesis in order to improve the selflubricating behaviour of the coatings.