Modellazione strutturale di edifici storici in muratura e misti: valutazioni comparate e criteri operativi

L’obiettivo della presente tesi è evidenziare l’importanza dell’approccio critico alla valutazione della vulnerabilità sismica di edifici in muratura e misti Il contributo della tesi sottolinea i diversi risultati ottenuti nella modellazione di tre edifici esistenti ed uno ipotetico usando due diversi programmi basati sul modello del telaio equivalente. La modellazione delle diverse ipotesi di vincolamento ed estensione delle zone rigide ha richiesto la formulazione di quattro modelli di calcolo in Aedes PCM ed un modello in 3muri. I dati ottenuti sono stati confrontati, inoltre, con l’analisi semplificata speditiva per la valutazione della vulnerabilità a scala territoriale prevista nelle “Linee Guida per la valutazione e riduzione del rischio sismico del Patrimonio Culturale”. Si può notare che i valori ottenuti sono piuttosto diversi e che la variabilità aumenta nel caso di edifici non regolari, inoltre le evidenze legate ai danni realmente rilevati sugli edifici mostrano un profondo iato tra la previsione di danno ottenuta tramite calcolatore e le lesioni rilevate; questo costituisce un campanello d’allarme nei confronti di un approccio acritico nei confronti del mero dato numerico ed un richiamo all’importanza del processo conoscitivo. I casi di studio analizzati sono stati scelti in funzione delle caratteristiche seguenti: il primo è una struttura semplice e simmetrica nelle due direzioni che ha avuto la funzione di permettere di testare in modo controllato le ipotesi di base. Gli altri sono edifici reali: il Padiglione Morselli è un edificio in muratura a pianta a forma di C, regolare in pianta ed in elevazione solamente per quanto concerne la direzione y: questo ha permesso di raffrontare il diverso comportamento dei modelli di calcolo nelle sue direzioni; il liceo Marconi è un edificio misto in cui elementi in conglomerato cementizio armato affiancano le pareti portanti in muratura, che presenta un piano di copertura piuttosto irregolare; il Corpo 4 dell’Ospedale di Castelfranco Emilia è un edificio in muratura, a pianta regolare che presenta le medesime irregolarità nel piano sommitale del precedente. I dati ottenuti hanno dimostrato un buon accordo per la quantificazione dell’indice di sicurezza per i modelli regolari e semplici con uno scarto di circa il 30% mentre il delta si incrementa per le strutture irregolari, in particolare quando le pareti portanti in muratura vengono sostituite da elementi puntuali nei piani di copertura arrivando a valori massimi del 60%. I confronti sono stati estesi per le tre strutture anche alla modellazione proposta dalle Linee Guida per la valutazione dell’indice di sicurezza sismica a scala territoriale LV1 mostrando differenze nell’ordine del 30% per il Padiglione Morselli e del 50% per il Liceo Marconi; il metodo semplificato risulta correttamente cautelativo. È, quindi, possibile affermare che tanto più gli edifici si mostrano regolari in riferimento a masse e rigidezze, tanto più la modellazione a telaio equivalente restituisce valori in accordo tra i programmi e di più immediata comprensione. Questa evidenza può essere estesa ad altri casi reali divenendo un vero e proprio criterio operativo che consiglia la suddivisione degli edifici esistenti in muratura, solitamente molto complessi poiché frutto di successive stratificazioni, in parti più semplici, ricorrendo alle informazioni acquisite attraverso il percorso della conoscenza che diviene in questo modo uno strumento utile e vitale. La complessità dell’edificato storico deve necessariamente essere approcciata in una maniera più semplice identificando sub unità regolari per percorso dei carichi, epoca e tecnologia costruttiva e comportamento strutturale dimostrato nel corso del tempo che siano più semplici da studiare. Una chiara comprensione del comportamento delle strutture permette di agire mediante interventi puntuali e meno invasivi, rispettosi dell’esistente riconducendo, ancora una volta, l’intervento di consolidamento ai principi propri del restauro che includono i principi di minimo intervento, di riconoscibilità dello stesso, di rispetto dei materiali esistenti e l’uso di nuovi compatibili con i precedenti. Il percorso della conoscenza diviene in questo modo la chiave per liberare la complessità degli edifici storici esistenti trasformando un mero tecnicismo in una concreta operazione culturale . Il presente percorso di dottorato è stato svolto in collaborazione tra l’Università di Parma, DICATeA e lo Studio di Ingegneria Melegari mediante un percorso di Apprendistato in Alta Formazione e Ricerca.

Studio Integrato Geomorfologico-Geofisico dell'Area Epicentrale del Terremoto del 20 Maggio 2012 (Mw 5.9) in Emilia-Romagna

La Sequenza Sismica Emiliana del 2012 ha colpito la zona compresa tra Mirandola e Ferrara con notevoli manifestazioni cosismiche e post-sismiche secondarie, soprattutto legate al fenomeno della liquefazione delle sabbie e alla formazione di fratturazioni superficiali del terreno. A fronte del fatto che la deformazione principale, osservata tramite tecniche di remote-sensing, ha permesso di individuare la posizione della struttura generatrice, ci si è interrogati sul rapporto tra strutture profonde e manifestazioni secondarie superficiali. In questa tesi è stato svolto un lavoro di integrazione di dati a varia scala, dalla superficie al sottosuolo, fino profondità di alcuni chilometri, per analizzare il legame tra le strutture geologiche che hanno generato il sisma e gli effetti superficiali percepiti dagli osservatori. Questo, non solo in riferimento allo specifico del sisma emiliano del 2012, ma al fine di trarre utili informazioni in una prospettiva storica e geologica sugli effetti di un terremoto “tipico”, in una regione dove le strutture generatrici non affiorano in superficie. Gli elementi analizzati comprendono nuove acquisizioni e rielaborazioni di dati pregressi, e includono cartografie geomorfologiche, telerilevamenti, profili sismici a riflessione superficiale e profonda, stratigrafie e informazioni sulla caratterizzazione dell’area rispetto al rischio sismico. Parte dei dati di nuova acquisizione è il risultato dello sviluppo e la sperimentazione di metodologie innovative di prospezione sismica in corsi e specchi d’acqua continentali, che sono state utilizzate con successo lungo il Cavo Napoleonico, un canale artificiale che taglia ortogonalmente la zona di massima deformazione del sisma del 20 Maggio. Lo sviluppo della nuova metodologia di indagine geofisica, applicata ad un caso concreto, ha permesso di migliorare le tecniche di imaging del sottosuolo, oltre a segnalare nuove evidenze co-sismiche che rimanevano nascoste sotto le acque del canale, e a fornire elementi utili alla stratigrafia del terreno. Il confronto tra dati geofisici e dati geomorfologici ha permesso di cartografare con maggiore dettaglio i corpi e le forme sedimentarie superficiali legati alla divagazione fluviale dall’VIII sec a.C.. I dati geofisici, superficiali e profondi, hanno evidenziato il legame tra le strutture sismogeniche e le manifestazioni superficiali seguite al sisma emiliano. L’integrazione dei dati disponibili, sia nuovi che da letteratura, ha evidenziato il rapporto tra strutture profonde e sedimentazione, e ha permesso di calcolare i tassi geologici di sollevamento della struttura generatrice del sisma del 20 Maggio. I risultati di questo lavoro hanno implicazioni in vari ambiti, tra i quali la valutazione del rischio sismico e la microzonazione sismica, basata su una caratterizzazione geomorfologico-geologico-geofisica dettagliata dei primi 20 metri al di sotto della superficie topografica. Il sisma emiliano del 2012 ha infatti permesso di riconoscere l’importanza del substrato per lo sviluppo di fenomeni co- e post-sismici secondari, in un territorio fortemente eterogeneo come la Pianura Padana.

RFID technology to support environmentally sustainable supply chain management

RFID is one of the contemporary technologies that has the potential to enable improved data gathering and cross-companies integration, and thus achieve cost efficiency. However, RFID has not yet become primary approach to collect data from the supply chain activities. This is partly due to (relative) high cost of implementation, partly due to technical deficiencies, as well as cross-company systems integration issues. This paper discusses a potential application area for RFID technology, which is environmentally sustainable supply chain management. The paper discusses the current practices in green supply chain management, and proposes possible applications of RFID enabling green supply chain management. The paper also proposes an idea of ad hoc RFID systems which are rapidly deployable and require minimal, if at all, pre-existing infrastructure. © 2010 IEEE.

Challenges of developing non-linear devices to achieve the linear Shannon limit

To achieve the Shannon Capacity Limit, we need to develop practical, effective and deployable non-linear devices to invert the non-linear effects of the transmission line. In this work, we will summarise the progress we are making to realise these, specifically looking at optical phase conjugation and phase regenerators as methods to improve non-linear tolerances. © 2014 IEEE.

Weak Polynomial Identities for M1,1(E)

* Partially supported by Universita` di Bari: progetto “Strutture algebriche, geometriche e descrizione degli invarianti ad esse associate”.

Practical and cost-effective high-fidelity optical carrier dissemination using coherent communication techniques

We report a unidirectional frequency dissemination scheme for high-fidelity optical carriers deployable over telecommunication networks. For the first time, a 10 Gb/s Binary Phase Shift Keying (BPSK) signal from an ultra-narrow linewidth laser was transmitted through a field-installed optical fibre with round-trip length of 124 km between Cork City and town of Clonakilty, without inline optical amplification. At the receiver, using coherent communication techniques and optical injection-locking the carrier was recovered with noise suppression. The beat signal between the original carrier at the transmitter and recovered carrier at the receiver shows a linewidth of 2.8 kHz. Long term stability measurements revealed fractional instabilities (True Allan deviation) of 3.3 × 10-14 for 1 s averaging time, prior to phase noise cancellation.

The absence of race in democratic politics: The case of the Dominican Republic

This dissertation explores the relationship between race and democratization. Through the examination of the case of the Dominican Republic, this study challenges mainstream explanations of democratic transitions. At its core, this dissertation aims at calling attention to the absence of race and ethnic allegiances as explanatory variables of the democratic processes and debates in the region. By focusing on structural variables, the analysis shies away from elite and actor-centered explanations that fall short in predicting the developments and outcomes of transitions. The central research questions of this study are: Why is there an absence of the treatment of race and ethnic allegiances during the democratic transitions in Latin America and the Caribbean? How has the absence of ethnic identities affected the nature and depth of democratic transitions? Unlike previous explanations of democratic transitions, this dissertation argues that the absence of race in democratic transitions has been a deliberate attempt to perpetuate limited citizenship by political and economic elites. Findings reveal a difficulty to overcome nationalist discourses where limited citizenship has affected the quality of democracy. Original field research data for the study has been gathered through semi-structured interviews and focus groups conducted from October 2008 to December 2009 in the Dominican Republic.

Headspace analysis of smokeless powders: Development of mass calibration methods using microdrop printing for chromatographic and ion mobility spectrometric detection

Smokeless powder additives are usually detected by their extraction from post-blast residues or unburned powder particles followed by analysis using chromatographic techniques. This work presents the first comprehensive study of the detection of the volatile and semi-volatile additives of smokeless powders using solid phase microextraction (SPME) as a sampling and pre-concentration technique. Seventy smokeless powders were studied using laboratory based chromatography techniques and a field deployable ion mobility spectrometer (IMS). The detection of diphenylamine, ethyl and methyl centralite, 2,4-dinitrotoluene, diethyl and dibutyl phthalate by IMS to associate the presence of these compounds to smokeless powders is also reported for the first time. A previously reported SPME-IMS analytical approach facilitates rapid sub-nanogram detection of the vapor phase components of smokeless powders. A mass calibration procedure for the analytical techniques used in this study was developed. Precise and accurate mass delivery of analytes in picoliter volumes was achieved using a drop-on-demand inkjet printing method. Absolute mass detection limits determined using this method for the various analytes of interest ranged between 0.03–0.8 ng for the GC-MS and between 0.03–2 ng for the IMS. Mass response graphs generated for different detection techniques help in the determination of mass extracted from the headspace of each smokeless powder. The analyte mass present in the vapor phase was sufficient for a SPME fiber to extract most analytes at amounts above the detection limits of both chromatographic techniques and the ion mobility spectrometer. Analysis of the large number of smokeless powders revealed that diphenylamine was present in the headspace of 96% of the powders. Ethyl centralite was detected in 47% of the powders and 8% of the powders had methyl centralite available for detection from the headspace sampling of the powders by SPME. Nitroglycerin was the dominant peak present in the headspace of the double-based powders. 2,4-dinitrotoluene which is another important headspace component was detected in 44% of the powders. The powders therefore have more than one headspace component and the detection of a combination of these compounds is achievable by SPME-IMS leading to an association to the presence of smokeless powders.

Disaster Risk Management Disparity in the Caribbean: Evidence from Barbados, Dominican Republic, Jamaica and Trinidad and Tobago

This study on risk and disaster management capacities of four Caribbean countries: Barbados, the Dominican Republic, Jamaica, and Trinidad and Tobago, examines three main dimensions: 1) the impact of natural disasters from 1900 to 2010 (number of events, number of people killed, total number affected, and damage in US$); 2) institutional assessments of disaster risk management disparity; and 3) the 2010 Inter-American Bank for Development (IADB) Disaster Risk and Risk Management indicators for the countries under study. The results show high consistency among the different sources examined, pointing out the need to extend the IADB measurements to the rest of the Caribbean countries. Indexes and indicators constitute a comparison measure vis-à-vis existing benchmarks in order to anticipate a capacity to deal with adverse events and their consequences; however, the indexes and indicators could only be tested against the occurrence of a real event. Therefore, the need exists to establish a sustainable and comprehensive evaluation system after important disasters to assess a country‘s performance, verify the indicators, and gain feedback on measurement systems and methodologies. There is diversity in emergency and preparedness for disasters in the four countries under study. The nature of the event (hurricanes, earthquakes, floods, and seismic activity), especially its frequency and the intensity of the damage experienced, is related to how each has designed its risk and disaster management policies and programs to face natural disasters. Vulnerabilities to disaster risks have been increasing, among other factors, because of uncontrolled urbanization, demographic density and poverty increase, social and economic marginalization, and lack of building code enforcement. The four countries under study have shown improvements in risk management capabilities, yet they are far from being completed prepared. Barbados‘ risk management performance is superior, in comparison, to the majority of the countries of the region. However, is still far in achieving high performance levels and sustainability in risk management, primarily when it has the highest gap between potential macroeconomic and financial losses and the ability to face them. The Dominican Republic has shown steady risk performance up to 2008, but two remaining areas for improvement are hazard monitoring and early warning systems. Jamaica has made uneven advances between 1990 and 2008, requiring significant improvements to achieve high performance levels and sustainability in risk management, as well as macroeconomic mitigation infrastructure. Trinidad and Tobago has the lowest risk management score of the 15 countries in the Latin American and Caribbean region as assessed by the IADB study in 2010, yet it has experienced an important vulnerability reduction. In sum, the results confirmed the high disaster risk management disparity in the Caribbean region.

Disater Risk Management Disparity in the Caribbean: Evidence from Barbados, Dominican Republic, Jamaica and Trinidad and Tobago

This study on risk and disaster management capacities of four Caribbean countries: Barbados, the Dominican Republic, Jamaica, and Trinidad and Tobago, examines three main dimensions: 1) the impact of natural disasters from 1900 to 2010 (number of events, number of people killed, total number affected, and damage in US$); 2) institutional assessments of disaster risk management disparity; and 3) the 2010 Inter-American Bank for Development (IADB) Disaster Risk and Risk Management indicators for the countries under study. The results show high consistency among the different sources examined, pointing out the need to extend the IADB measurements to the rest of the Caribbean countries. Indexes and indicators constitute a comparison measure vis-à-vis existing benchmarks in order to anticipate a capacity to deal with adverse events and their consequences; however, the indexes and indicators could only be tested against the occurrence of a real event. Therefore, the need exists to establish a sustainable and comprehensive evaluation system after important disasters to assess a country’s performance, verify the indicators, and gain feedback on measurement systems and methodologies. There is diversity in emergency and preparedness for disasters in the four countries under study. The nature of the event (hurricanes, earthquakes, floods, and seismic activity), especially its frequency and the intensity of the damage experienced, is related to how each has designed its risk and disaster management policies and programs to face natural disasters. Vulnerabilities to disaster risks have been increasing, among other factors, because of uncontrolled urbanization, demographic density and poverty increase, social and economic marginalization, and lack of building code enforcement. The four countries under study have shown improvements in risk management capabilities, yet they are far from being completed prepared. Barbados’ risk management performance is superior, in comparison, to the majority of the countries of the region. However, is still far in achieving high performance levels and sustainability in risk management, primarily when it has the highest gap between potential macroeconomic and financial losses and the ability to face them. The Dominican Republic has shown steady risk performance up to 2008, but two remaining areas for improvement are hazard monitoring and early warning systems. Jamaica has made uneven advances between 1990 and 2008, requiring significant improvements to achieve high performance levels and sustainability in risk management, as well as macroeconomic mitigation infrastructure. Trinidad and Tobago has the lowest risk management score of the 15 countries in the Latin American and Caribbean region as assessed by the IADB study in 2010, yet it has experienced an important vulnerability reduction. In sum, the results confirmed the high disaster risk management disparity in the Caribbean region.

Headspace Analysis of Smokeless Powders: Development of Mass Calibration Methods using Microdrop Printing for Chromatographic and Ion Mobility Spectrometric Detection

Smokeless powder additives are usually detected by their extraction from post-blast residues or unburned powder particles followed by analysis using chromatographic techniques. This work presents the first comprehensive study of the detection of the volatile and semi-volatile additives of smokeless powders using solid phase microextraction (SPME) as a sampling and pre-concentration technique. Seventy smokeless powders were studied using laboratory based chromatography techniques and a field deployable ion mobility spectrometer (IMS). The detection of diphenylamine, ethyl and methyl centralite, 2,4-dinitrotoluene, diethyl and dibutyl phthalate by IMS to associate the presence of these compounds to smokeless powders is also reported for the first time. A previously reported SPME-IMS analytical approach facilitates rapid sub-nanogram detection of the vapor phase components of smokeless powders. A mass calibration procedure for the analytical techniques used in this study was developed. Precise and accurate mass delivery of analytes in picoliter volumes was achieved using a drop-on-demand inkjet printing method. Absolute mass detection limits determined using this method for the various analytes of interest ranged between 0.03 - 0.8 ng for the GC-MS and between 0.03 - 2 ng for the IMS. Mass response graphs generated for different detection techniques help in the determination of mass extracted from the headspace of each smokeless powder. The analyte mass present in the vapor phase was sufficient for a SPME fiber to extract most analytes at amounts above the detection limits of both chromatographic techniques and the ion mobility spectrometer. Analysis of the large number of smokeless powders revealed that diphenylamine was present in the headspace of 96% of the powders. Ethyl centralite was detected in 47% of the powders and 8% of the powders had methyl centralite available for detection from the headspace sampling of the powders by SPME. Nitroglycerin was the dominant peak present in the headspace of the double-based powders. 2,4-dinitrotoluene which is another important headspace component was detected in 44% of the powders. The powders therefore have more than one headspace component and the detection of a combination of these compounds is achievable by SPME-IMS leading to an association to the presence of smokeless powders.