猪场废水短程硝化反硝化-厌氧氨氧化脱氮研究

畜禽废水是农村水环境污染的主要来源之一，其处理的难点在于脱氮。传统生物脱氮法具有能耗高、需大量外加碳源等缺点，开发低成本、高效率的新型生物脱氮技术具有重要意义。 本研究将短程硝化反硝化和厌氧氨氧化两种脱氮新技术结合，让前者为后者创造去除可降解COD、降低总氮负荷、调整pH、调整氨氮和亚硝酸盐氮浓度比例等进水条件，而后者可在无需外加碳源的条件下进一步脱氮，二者结合可成为高氨氮、低C/N废水脱氮的新途径。 试验以低碳氮比猪场废水为研究对象，首先进行了短程硝化反硝化预处理研究，同时启动并运行调控厌氧氨氧化反应器，最后以经过短程硝化反硝化预处理的猪场废水为进水，进行厌氧氨氧化脱氮考察。实验表明：（1）短程硝化反硝化作为厌氧氨氧化的预处理工序是可行的。猪场废水通过短程硝化反硝化，可以达到基本去除可生化COD、部分脱氮、控制出水氨氮和亚硝酸盐氮浓度之比在1︰1左右、pH在7.5～8.0的目的， COD和总氮平均去除率分别为64.3%、49.1%,出水可达到厌氧氨氧化反应的进水要求。（2）采用模拟废水启动厌氧氨氧化反应器，经过5个月左右的运行调控，反应器启动成功并稳定运行，最高总氮去除率为87.1%，总氮容积去除率最高达到0.14kg/m3.d；整个稳定阶段，氨氮、亚硝酸盐氮、硝酸盐氮的变化量之比为1︰1.21︰0.33。（3）经过短程硝化反硝化预处理的猪场废水厌氧氨氧化脱氮效果稳定，氨氮、亚硝酸盐氮、总氮、COD的平均去除率分别为93.0%、99.4%、84.6%、18.1%，处理效果与模拟废水处理系统相比无明显变化。（4）经过短程硝化反硝化预处理后，猪场废水中残留有机物成分在厌氧氨氧化反应过程中无显著变化，主要为酯类和烷烃类物质；残留有机物对厌氧氨氧化效果无明显影响。（5）采用PCR技术进行特殊功能菌种检测，结果表明模拟废水处理系统和猪场废水处理系统的菌群中均含有厌氧氨氧化菌和好氧硝化菌；通过blast比对，厌氧氨氧化菌扩增序列与未培养的Planctomycetales菌和Candidatus Brocadia fulgida菌16S rRNA部分序列相似性分别为95％、90%。（6）MPN法菌种计数结果显示，模拟废水处理系统和猪场废水处理系统的菌群中均含有硝化细菌、亚硝化细菌和少量反硝化菌，实验条件下的微生物系统是一个厌氧氨氧化菌与好氧硝化菌、反硝化菌共存的系统。 Poultry wastewater is one of the main source of water pollution in rural areas，and nitrogen removal is the most difficult part in treating poultry wastewater. There are some disadvantages in traditional nitrogen removal, such as high energy consumption and more additional organic carbon. It is important to develop ecolomical and efficient technologyies. Shortcut nitricfication/denitrification, as a pretreatment process, was combined with Anammox in this research, so that part of total nitrogen and most degradable COD could be removed by the former, and further nitrogen removal could be implemented by the latter. The combination of the two technologies was a new approach to treat wastewater with high ammonium and low C/N. Piggery wastewater with low C/N was treated in lab-scale experiment. Firstly, shortcut nitrification/denitrification was investigated, and Anammox reactor was started up successfully at the same time. Then piggery wastewater after pretreatment was treated by Anammox. The results showed :(1) It was feasible to take nitrification/denitrification as the pretreatment process of Anammox. By using this process, part of total nitrogen and COD were removed, the ratio of ammonium and nitrite reached around 1︰1 and the pH was about 7.8, which were favorable for Anammox. The average removal percentage of COD and total nitrogen were about 64.3% and 49.1%, respectively. (2) Simulated wastewater was used to start up Anammox reactor. The reactor was started up successfully within 5 months and stable performance was achieved. The highest nitrogen removal reached 87.1% and the biggest volumetric total nitrogen removal rate reached 0.14kg/m3.d. The average ratio of ammonium, nitrite and nitrate was 1:1.21:0.33. (3)Taking the effluent of shortcut nitrification/denitrification as the influent, the nitrogen removal efficiency of Anammox was stable, and the the average removal percentage of ammonium, nitrite, total nitrogen and COD were 93.0%, 99.4% , 84.6% and 18.1%, respectively, which had little difference with that by using simulated wastewater..(4) After pretreatment, the residual organic carbon in piggery wastewater showed no obvious change during the Anammox process, and the main organic compounds were saturated hydrocarbon and ester, which had no obvious negative effect on Anammox process.(5) By PCR technology, the existence of Anammox bacteria was confirmed and the aerobic nitrifying bacteria was found to coexist as well. The result of blast showed that the identities of Anammox bacterium to part of 16S rRNA sequence of uncultured Planctomycetales bacterium and Candidatus Brocadia fulgida bacterium were 95% and 90%, respectively.（6）By MPN method, nitrite oxidizer, ammonium oxidizer and denitrification bacteria were detected in both simulated and piggery wastewater treatment system of Anammox, and the microorganism system was composed of Anammox bacteria，aerobic bacteria and denitrification bacteria together.

高效石油烃降解菌的分离鉴定及降解特性

为获得更为丰富的石油降解微生物资源,从沈抚污灌区石油污染土壤和实验室高浓度柴油胁迫土壤中筛选出了4株高效石油烃降解菌SF-422、SF-428、SF-433和SYS-1.这4株菌总石油烃(Total petroleum hydrocarbon/TPH)生物降解率为67.4%~73.6%.经过16项生理生化特性实验和16S rDNA序列分析鉴定,SF-433,SF-428,SF-422和SYS-1分别为蜡状芽孢杆菌(Bacillus cereus),木糖氧化无色杆菌(Achromobacter xylosoxidans),施氏假单胞菌(Pseudomonas stutzeri)和洋葱伯克霍尔德氏菌(Burkholderia cepacia).纯烃降解定性实验表明所筛选出的4株高效降解菌均能够利用正十六烷、苯、菲和环己烷为唯一碳源生长,其中菌株SF-428和SYS-1显示了对芳烃及环烷烃较强的利用能力.

Decomposition of transformer oil under ultrasonic irradiation during degassing process

In the degassing process of transformer oil with ultrasonic waves, decomposition of the oil was observed. Light hydrocarbons, including methane, ethane, ethylene, acetylene, propane etc, were found to be released continuously from the oil into headspace within a closed vial placed in an ultrasonic field. The gases came from decomposition of hydrocarbon Molecules under cavitation effect.

Remediation of Persistent Organic Pollutants (POPs) in Two Different Soils

Persistent organic pollutants (POPs) are a set of chemicals that are toxic, persist in the environment for long periods of time, and biomagnify as they move up through the food chain. The most widely used method of POP destruction is incineration, which is expensive and could result in undesirable by-products. An alternative bioremediation technology, which is cheaper and environ-mentally friendly, was tested during this experiment. Two different soil types containing high and low organic matter (OM) were spiked with 100 mg/kg each of pyrene and Aroclor 1248 and planted with three different species of grasses. The objective of the study was to determine residue recovery levels (availability) and potential effectiveness of these plant species for the remediation of POPs. The results showed that recovery levels were highly dependent on the soil organic matter content—very low in all treatments with the high OM content soil compared to recoveries in the low OM soil. This indicates that availability, and, hence, biodegradability of the contaminants is dependent on the organic matter content of the soil. Moreover, the degree of availability was also significantly different for the two classes of chemicals. The polyaromatic hydrocarbon (PAH) recovery (availability) was extremely low in the high organic matter content soil compared to that of the polychlorinated biphenyls (PCBs). In both soil types, all of the plant species treatments showed significantly greater PCB biodegradation compared to the unplanted controls. Planting did not have any significant effect on the transformation of the PAHs in both soil types; however, planting with switchgrass was the best remedial option for both soil types contaminated with PCB.

Infrared spectroscopic study on thermal behavior of Langmuir-Blodgett films of octadecyl ammonium octadecanoate and octadecylammonium octadecanoate-d(35)

Langmuir-Blodgett (LB) films of octadecylammonium octadecanoate (C(18)H(37)j7NH(3)(+)C(17)H(35)COO(-),ODASA) and octadecylammonium octadecanoate-d(35) (C18H37+NH3+C17D35COO-, ODASA-d(53)) were prepared and their thermal behaviors were investigated by variable-temperature Fourier transform infrared transmission spectroscopy. It was found that the two hydrocarbon chains of ODASA molecule in LB films are highly ordered while that protonated (H) chain in ODASA-d(35) is partially disordered with some gauche conformers introduced at room temperature.

Effect of diffusion barrier on the high-temperature oxidation behavior of thermal barrier coatings

A selective oxidation technique has been applied to form a diffusion barrier on the Ni-based superalloy substrate by heating the substrate with electron beam of the electron beam-physical vapor deposition (EB-PVD) facility. The interdiffusion behavior, cross-sectional morphology, isothermal and cyclic oxidations were studied for thermal barrier coatings (TBCs) with and without diffusion barrier.

Bump-Surface Multicompartment Micelles from a Linear ABC Triblock Copolymer: A Combination Study by Experiment and Computer Simulation

Novel bump-surface multicompartment micelles formed by a linear amphiphilic ABC triblock copolymer via self-assembly in selective solvent were successfully observed both in simulation and experiment. The results revealed that the block A forms the most inner core, and the blocks B and C form the inner and outer layers, respectively, and the bumps were formed by block A and more likely to be born on curving surfaces. Moreover, the micelle shape could be controlled by changing the solvent selectivity of the blocks A and B. Spherical, cylindrical, and discoidal micelles with bumpy surfaces were obtained both in experiment and simulation.

Oxidation of cyclohexane - A significant impact of stainless steel reactor wall

The selective oxidation of cyclohexane to cyclohexanol and cyclohexanone is an important chemical process and it has been paid more attentions recently. In the present work, the stainless steel reactor wall was found to influence the selective oxidation of cyclohexane very significantly, and a quasi-crystalline Ti45Zr35Ni17Cu3 alloy with the similar compositions as the reactor wall was used as a catalyst for the cyclohexane oxidation, as expected, a higher activity was obtained with it. The present results open up a new avenue for developing new catalyst for alkane oxidation.

An infrared study on Langmuir-Blodgett films of octadecylammonium octadecanoate: FWHM and the vibrational coupling

The monolayer of the mixture of octadecanoic acid and octadecylamine with molar ratio 1: 1 has been investigated at the air-water interface. It was found that the monolayer shows a rather stable state at the surface pressure of 30 mN/m and this monolayer can be transferred onto a CaF2 plate by Langmuir-Blodgett (LB) technique. The infrared spectra of LB films indicated that octadecyl ammonium octadecanoate is formed by an intermolecular proton exchange between adjacent carboxylic and aminic groups (COO- and NH3+). In three-layer LB film, the CH2 scissoring mode of the long hydrocarbon chains of octadecyl ammonium octadecanoate shows a broad band feature at about 1468 cm(-1) while this vibrational mode of three-layer LB film of the mixture (1: 1) of deuterated stearic acid and octadecylamine (octadecylammonium octadecanoate-d35, C18H37NH3+C17D35COO-) only shows a narrow band. The broad feature of the CH2 scissoring mode in octadecylammonium octadecanoate probably originates from the coupling between the chain of stearic acid and that of octadecylamine while this kind of coupling could be completely removed in octadecylammonium octadecanoate-d35.

Infrared spectrum of 2-octadecyl-7,7,8,8-tetracyanoquinodimethane

Infrared spectrum of 2-octadecyl-7,7,8,8-tetracyanoquinodimethane was dealt with 2nd-derivative and deconvolution methods. It was first discovered that the band near 2849 cm(-1) assigned to the CH2 Symmetric stretching mode splited into two bands and this splitting might result from the coexistence of two kinds of conformations of CH2 in the hydrocarbon chain.

A study on the catalytic behaviors of concentrated heteropolyacid solution - I. A novel catalyst for isobutane alkylation with butene

The catalytic behaviors of a novel liquid acid catalyst (composed of heteropolyacid and acetic acid) for alkylation of isobutane with butene was investigated. As a solvent acetic acid had a synergistic effect. It enhanced the acid strength of HPA and its stability. The conditions for the formation of the catalytically active phase were studied systematically. The content of crystal water of HPA and the quantity of solvent affect the formation of active phase and the catalytic activity. Catalytically active phase consists of HPA, acetic acid and hydrocarbon produced from the reaction, as well as traces of water from the crystal water of HPA. This catalyst system is comparable to the sulfuric acid in catalytic activity.

Self-assembled monolayer growth of phospholipids on hydrophobic surface toward mimetic biomembranes: Scanning probe microscopy study

Atomic force microscopy (AFM) and lateral force microscopy (LFM) were used simultaneously to analyze a model membrane bilayer structure consisting of a phospholipid outer monolayer deposited onto organosilane-derivatized mica surfaces, which were constructed by using painting and self-assembly methods. The phospholipid used as outer monolayer was dimyristoylphosphatidylcholine (DMPC). The hydrocarbon-covered substrate that formed the inner half bilayer was composed of a self-assembly monolayer (SAM) of octadecyltrichloroorganosilane (OTS) on mica. SAMs of DMPC were formed by exposing hydrophobic mica to a solution of DMPC in decane/isobutanol and subsequently immersing into pure water. AFM images of samples immersed in solution for varying exposure times showed that before forming a complete monolayer the molecules aggregated into dense islands (2.2-2.6 nm high) on the surface. The islands had a compact and rounded morphology. LFM, coupled with topographic data obtained with the atomic force mode, had made possible the distinction between DMPC and OTS. The rate constant of DMPC growth was calculated. This is the first systematic study of the SAM formation of DMPC by AFM and LFM imaging. It reveals more direct information about the film morphology than previous studies with conventional surface analytical techniques such as infrared spectroscopy, X-ray, or fluorescence microscopy.

X-ray photoelectron spectroscopy and mass spectra study of alpha-amino acid

X-ray photoelectron spectroscopy and mass spectrometry have been used to study the ten alpha-Amino Acids. The chemical shiftss of N-1s electron binding energy have been explained by means of the difference in the hydrocarbon group of amino acids. The influence of the hydrocarbon group on NH2 has been disscussed using the XPS and MS results.