Lifetime of silica final lenses subject to HiPER irradiation conditions

The goal of the European laser fusion project, is to build an engineering facility for repetitive laser operation (HiPER 4a) and later a fusion reactor (HiPER 4b). A key aspect for laser fusion energy is the final optics. At the moment, it is based on silica transmission lenses located 8 m away from the chamber center. Lens lifetime depends on the irradiation conditions. We have used a 48 MJ shock ignition target for calculations. We have studied the thermo-mechanical effects of ions and X-rays on the lenses. Ions lead to lens melting and must therefore be mitigated. On the other hand, X-rays (~1% of the energy) does not produce either a significant temperature rise or detrimental stresses. Finally, we calculated the neutron flux and gamma dose rate on the lenses. Next, based on a simple model we studied the formation of color centers in the sample, which lead to optical absorption. Calculations show that simultaneous neutron and gamma irradiation does not significantly increase the optical absorption during the expected lifetime of the HiPER 4a facility. Under severe conditions (HiPER 4b), operation above 800 K or lens refreshing by thermal annealing treatments seem to assure adequate behavior.

Thermal behaviour of Sunrise, a balloon-borne solar Telescope

Sunrise is a solar telescope, successfully flown in June 2009 with a long duration balloon from the Swedish Space Corporation Esrange launch site. The design of the thermal control of SUNRISE was quite critical because of the sensitivity to temperature of the optomechanical devices and the electronics. These problems got more complicated due the size and high power dissipation of the system. A detailed thermal mathematical model of SUNRISE was set up to predict temperatures. In this communication the thermal behaviour of SUNRISE during flight is presented. Flight temperatures of some devices are presented and analysed. The measured data have been compared with the predictions given by the thermal mathematical models. The main discrepancies between flight data and the temperatures predicted by the models have been identified. This allows thermal engineers to improve the knowledge of the thermal behaviour of the system for future missions.

Amplificador de potencia clase F a 1.64 ghz con control de armónicos

This paper presents a high-power high efficiency PA design method using load pull technique. Harmonic impedance control at the virtual drain is accomplished through the use of tunable pre-matching circuits and modeling of package parasitics. A 0.5 µm GaN high electron mobility transistor (HEMT) is characterized using the method, and loadpull measurements are simulated illustrating the impact of varying 2nd and 3rd harmonic termination. These harmonic terminations are added to satisfy conditions for class-F load pull. The method is verified by design and simulation of a 40-W class-F PA prototype at 1.64 GHz with 76% drain efficiency and 10 dB gain (70% PAE).

Banco de medidas automático para linealización de amplificadores

This work is focused on building and configuring a measurement test bench for non linear High Power Amplifiers, more precisely those ones based on the Envelope Elimination and Restoration. At first sight the test bench is composed of several arbitrary waveform generators, an oscilloscope, a vector signal generator and a spectrum analyzer all of them controlled remotely. The test bench works automatically, that is why several software control programs have been developed in order to control all this equipment. The control programs have been developed in Matlab/Octave Scripting language and at last chance in a more low level language as C. The signal processing algorithms, taking into account that the time alignment one is the most important, have been developed in Matlab/Octave Scripting too. An improvement of 10dB in the ACPR(Adjacent Channel Power Ratio) has been obtained just by applying the time alignment algorithm developed in this work

IFE Plant Technology Overview and contribution to HiPER proposal

HiPER is the European Project for Laser Fusion that has been able to join 26 institutions and signed under formal government agreement by 6 countries inside the ESFRI Program of the European Union (EU). The project is already extended by EU for two years more (until 2013) after its first preparatory phase from 2008. A large work has been developed in different areas to arrive to a design of repetitive operation of Laser Fusion Reactor, and decisions are envisioned in the next phase of Technology Development or Risk Reduction for Engineering or Power Plant facilities (or both). Chamber design has been very much completed for Engineering phase and starting of preliminary options for Reactor Power Plant have been established and review here.

Optimizing three-phase planar transformer construction

A three-phase transformer with flat conductor layers is proposed in this article. This arrangement is used for high current density transformers. Cost effectiveness in planar magnetic are related with the optimization in the number of layers in each winding. This fact takes more relevance for the medium and high power three-phase transformers where the number of parallels to achieve the required DCR is increased. The proposed method allows the use of off-the-shell core shapes that are used for single phase transformers. Cost impact is significant and design implications become more flexible. The proposed solution has been validated and compared using the conventional and the proposed methodologies to design a high power (20 kW) transformer.

Contribution sharing of a fuel mixture components to the fuel cell potencial of a direct alcohol fuel cell

The increasing worldwide demand for electricity impels to develop clean and renewable energy resources. In the field of portable power devices not only size and weight represent important aspects to take into account, but the fuel and its storage are also critical issues to consider. In this last sense, the direct methanol (MeOH) fuel cells (DMFC) play an important role as they can offer high power and energy density, low emissions, ambient operating conditions and fast and convenient refuelling.

Comparative study of ion beam-irradiation effects on silica and α-quartz: evidences for excitonic mechanisms

Introduction - SiO 2 •Simple composition and structure; Crystalline and amorphous phases •Adequate for atomistic simulations •Abundant in nature. Relevant for many technologies -Irradiation with swift heavy ions: •They provide EXTREME physical conditions •Very high excitation densities similar to high power lasers •Very high local temperatures •By playing with high energy and heavy mass (SHI) : •One can go from low electronic excitations (collisions regime) to high electronic excitations (electronic regime

Physical characterization of laser interaction and shock generation in laser processing: coupled theoretical-experimental analysis

Outline: • Introduction • Fundamental Physics of the Laser-Plasma Interaction in Laser Shock Processing • Theoretical/Computational Model Description • Some Results. Analysis of Interaction Parameters • Experimental Validation. Diagnosis Setup • Discussion and Outlook

Envelope Amplifier Based on a Hybrid Series Converter With The Slow-envelope Technique

High frequency dc-dc switching converters are used as envelope amplifiers in RF transmitters. The dc-dc converter should operate at very high frequency to track an envelope in the MHz range to supply the power amplifier. One of the circuits suitable for this application is a hybrid topology composed of a switched converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. This topology can take advantage of the reduced slew-rate technique where switching dc-dc converter provides the RF envelope with limited slew rate in order to avoid high switching frequency and high power losses, while the linear regulator performs fine adjustment in order to obtain the exact replica of the RF envelope. The combination of this control technique with this topology is proposed in this paper. Envelopes with different bandwidth will be considered to optimize the efficiency of the dc-dc converter. The calculations and experiments have been done to track a 2MHz envelope in the range 0-12V for an EER RF transmitter.

An alternative for reducing the layers in the construction of three-phase planar transformers

A modified winding layout for three-phase transformers with PCB windings is proposed in this paper. This modified layout can be used in high current transformers with many PCB layers to simplify the fabrication process. One of the key factors that might increase the cost and complexity in the construction of planar transformers is the number of layers of each PCB winding. This issue becomes even more important in medium-high power three-phase transformers, where the number of PCB layers is higher. In addition to that, the proposed method allows the use of commercial core shapes that are commonly used to design single-phase transformers. This fact makes possible the reduction of cost and flexibility of the design solutions. The proposed solution has been validated and compared using the conventional and the proposed methodologies to design a high power (20 kW) transformer.

Análisis de la influencia de los diferentes parámetros de diseño en la aparición de fatiga superficial en contactos mecánicos

La fatiga superficial es uno de los principales problemas en las transmisiones mecánicas y es uno de los focos de atención de las investigaciones de los últimos anos en Tribología. La disminución de viscosidad de los lubricantes para la mejora de la eficiencia, el aumento de las potencias a transmitir, el aumento de la vida de los componentes o la mejora de su fiabilidad han supuesto que los fenómenos de fatiga superficial hayan cobrado especial relevancia, especialmente los fenómenos de pitting y micropitting en cajas multiplicadoras/reductoras de grandes potencias de aplicación, por ejemplo, en el sector eólico. Como todo fenómeno de fatiga, el pitting y micropitting son debidos a la aplicación de cargas ciclicas. Su aparición depende de las presiones y tensiones cortantes en el contacto entre dos superficies que al encontrarse en rodadura y deslizamiento varian con el tiempo. La principal consecuencia de la fatiga superficial es la aparición de hoyuelos de diferente magnitud segun la escala del fenómeno (pitting o micropitting) en la superficie del material. La aparición de estos hoyuelos provoca la perdida de material, induce vibraciones y sobrecargas en el elemento que finalmente acaba fallando. Debido a la influencia de la presión y tensión cortante en el contacto, la aparición de fatiga depende fuertemente del lubricante que se encuentre entre las dos superficies y de las condiciones de funcionamiento en las cuales este trabajando. Cuando el contacto trabaja en condiciones de lubricacion mixta-elastohidrodinamica tiende a aparecer micropitting debido a las altas tensiones localizadas en las proximidades de las asperezas, mientras que si el régimen es de lubricación completa el tipo de fatiga superficial suele ser pitting debido a las tensiones mas suavizadas y menos concentradas. En esta Tesis Doctoral se han analizado todos estos factores de influencia que controlan el pitting y el micropitting prestando especial atención al efecto del lubricante. Para ello, se ha dado un enfoque conjunto a ambos fenómenos resolviendo las ecuaciones involucradas en el contacto elastohidrodinamico no-Newtoniano (la ecuación de Reynolds, la deformación elástica de los sólidos y la reologia del lubricante) para conocer la presión y la tensión cortante en el contacto. Conocidas estas, se resuelve el campo de tensiones en el interior del material y, finalmente, se aplican criterios de fatiga multiaxial (Crossland, Dang Van y Liu-Mahadevan) para conocer si el material falla o no falla. Con la metodología desarrollada se ha analizado el efecto sobre las tensiones y la aparición de la fatiga superficial del coeficiente viscosidad-presion, de la compresibilidad, del espesor especifico de película y de la fricción así como de la influencia de las propiedades a fatiga del material y de las condiciones de funcionamiento (radios de contacto, velocidad, deslizamiento, carga y temperatura). Para la validación de los resultados se han utilizado resultados teóricos y experimentales de otros autores junto con normas internacionales de amplia utilización en el mundo industrial, entre otras, para el diseño y calculo de engranajes. A parte del trabajo realizado por simulación y cálculo de los diferentes modelos desarrollados, se ha realizado un importante trabajo experimental que ha servido no solo para validar la herramienta desarrollada sino que además ha permitido incorporar al estudio factores no considerados en los modelos, como los aditivos del lubricante. Se han realizado ensayos de medida del coeficiente de fricción en una maquina de ensayo puntual con la que se ha validado el cálculo del coeficiente de fricción y se ha desarrollado un proceso de mejora del coeficiente de fricción mediante texturizado superficial en contactos puntuales elastohidrodinamicos mediante fotolitografia y ataque quimico. Junto con los ensayos de medida de fricción en contacto puntual se han realizado ensayos de fricción y fatiga superficial en contacto lineal mediante una maquina de discos que ha permitido evaluar la influencia de diferentes aditivos (modificadores de fricción, antidesgaste y extrema-presion) en la aparición de fatiga superficial (pitting y micropitting) y la fricción en el contacto. Abstract Surface fatigue is one of the most important problems of mechanical transmissions and therefore has been one of the main research topics on Tribology during the last years. On the one hand, industrial demand on fuel economy has led to reduce lubricant viscosity in order to improve efficiency. On the other hand, the requirements of power and life of machine elements are continuously increasing, together with the improvements in reliability. As a consequence, surface fatigue phenomena have become critical in machinery, in particular pitting and micropitting in high power gearboxes of every kind of machines, e.g., wind turbines or cranes. In line with every fatigue phenomena, pitting and micropitting are caused by cyclic loads. Their appearance depends on the evolution of pressures and shear stresses with time, throughout the contact between surfaces under rolling and sliding conditions. The main consequence of surface fatigue is the appearance of pits on the surface. The size of the pits is related to the scale of the fatigue: pitting or micropitting. These pits cause material loss, vibrations and overloads until the final failure is reached. Due to the great influence of the pressures and shear stresses in surface fatigue, the appearance of pits depends directly on the lubricant and the operating conditions. When the contact works under mixed regime (or under elastohydrodynamic but close to mixed regime) the main fatigue failure is micropitting because of the high pressures located near the asperities. In contrast, when the contact works under elastohydrodynamic fully flooded conditions the typical fatigue failure is pitting. In this Ph.D. Thesis, the main factors with influence on pitting and micropitting phenomena are analyzed, with special attention to the effect of the lubricant. For this purpose, pitting and micropitting are studied together by solving the equations involved in the non-Newtonian elastohydrodynamic contact. Thus, pressure and shear stress distributions are found by taking into account Reynolds equation, elastic deflection of the solids and lubricant rheology. Subsequently, the stress field inside the material can be calculated and different multiaxial fatigue criteria (Crossland, Dang Van and Liu- Mahadevan) can be applied to predict whether fatigue failure is reached. The influences of the main parameters on pressure and surface fatigue have been studied, taking into account the lubricant compressibility and its viscosity-pressure coefficient, the specific film thickness, the friction coefficient and the fatigue properties of the contacting materials, together with the operating conditions (contact radius, mean velocity, sliding velocity, load and temperature). Several theoretical and experimental studies of different authors have been used to validate all the results obtained, together with international standards used worldwide in gear design industry. Moreover, an experimental stage has been carried out in order to validate the calculation methods and introduce additional influences not included previously, e.g., lubricant additives. The experimentation includes different friction tests in point contacts performed with a tribological equipment in order to validate the results given by the calculations. Furthermore, the reduction and optimization of the friction coefficient is analyzed by means of textured surfaces, obtained combining photolithography and chemical etching techniques. Besides the friction tests with point contact, friction and surface fatigue tests have also been performed with line contact in a tribological test rig. This equipment is also used to study the influence of different types of additives (friction modifiers, anti-wear and extreme-pressure additives) on surface fatigue (pitting and micropitting).

Optically Induced Reorientation in Nematic Cylindrical Structures

Cyclindrical structures of nematics give rise to several opto-optical effects related to molecular reorientation. One of these effects is the formation of diffraction ring patterns similar to the ones observed in planar cells, but differing in shape. Another effect has been observed, namely a quasi-chaotic motion of rings with a very large angular spread; this motion can be obtained using a cw laser and high power densities. The phenomenon could be attributed to thermal motion, however, there are some features that cannot be explained by a purely thermal effect, e.g., a wavelength dependence of the threshold and the frequencies of the ring motion.

Desarrollo y validación de tecnologías de intensificación lumínica para fotobiorreactores (FBR) para el aprovechamiento de la radiación en el cultivo de microalgas

En la actualidad la humanidad se enfrenta a una serie de problemas de gran transcendencia que van a determinar en alto grado los niveles de calidad de vida en los próximos años. El calentamiento global, el incremento demográfico incontrolado, la contaminación ambiental y la escasez de recursos así como una mala distribución de los mismos, son sólo algunos ejemplos. En este contexto, las microalgas, microrganismos fotosintéticos de alta eficiencia y versatilidad, presentan una serie de características que las convierten a priori en la base de una tecnología con un enorme potencial para formar parte de la solución a estos graves problemas planteados. Uno de los principales factores que impiden una mayor implantación de la tecnología de microalgas es de tipo económico. La baja productividad por unidad de área de los sistemas de cultivo actuales y la alta inversión necesaria en equipos y mantenimiento, hace que solo se justifique el cultivo de productos de muy alto valor añadido. Las soluciones pasan por aumentar el rendimiento global de los cultivos y por disminuir los costes de equipos e instalaciones. La presente tesis investiga sobre la posibilidad de conseguir un mejor aprovechamiento de la luz solar incidente sobre un cultivo de microalgas mediante el uso de una serie de dispositivos ópticos que vienen a denominarse intensificadores lumínicos. De entre los factores que determinan la productividad de un campo de cultivo de microalgas, posiblemente el más determinante sea la cantidad de radiación que las microalgas pueden aprovechar. Los intensificadores aumentan la disponibilidad de luz en el interior de los tubos de cultivo, de forma que la fotosíntesis se vea favorecida y, de este modo, se incremente la tasa de crecimiento de las microalgas. En el desarrollo de la tesis se proponen tres tipologías diferentes de intensificador diseñadas en base a criterios óptico-geométricos. Para cada una de estas tipologías se evalúa el incremento de radiación que se lograría sobre un tubo de cultivo. Paralelamente se desarrolla un modelo que permite la evaluación de la productividad del cultivo. Esto permite añadir el factor biológico al puramente óptico-físico y valorar las distintas propuestas de intensificadores en función de las características propias del microalga utilizada en el cultivo. El modelo es verificado y contrastado frente a datos de producción obtenidos en la bibliografía. Finalmente, la exposición concluye con una presentación general de las futuras líneas de investigación. ABSTRACT Today, humanity is facing a series of problems of global significance that will determine the standard of living in the years ahead. Global warming, uncontrolled population growth, pollution, lack of resources and poor distribution of them are just an example of the challenges we are facing. In this context, microalgae, high efficient photosynthetic microorganisms, have a number of characteristics that turn them into a very promising technology that can contribute or be part of a sustainable solution. One of the main factors preventing the adoption of microalgae technology is economical. The low productivity per unit area of current farming systems and the high investment needed in equipment and maintenance, only justifies the cultivation of algae for high value applications. One solution could be increasing the overall yield of the crops and reduce the equipment and facilities costs. Among the factors that determine the productivity of a microalgae culture, possibly the most influential one is the amount of radiation that microalgae receive. This Thesis develops the possibility of making better use of the sunlight radiation incident on a crop field using a series of devices similar to solar collectors. The solar collectors proposed are intended to increase the availability of light inside the culture tubes and within it, the tax of photosynthesis and the overall growth rate of the microalgae. In this research, three different configurations of collectors are designed, based on optical and geometrical criteria. For each one of these collectors, the increase on radiation that would be expected is evaluated. Furthermore, a model for light distribution inside the culture is developed in terms to estimate the biomass productivity. This allows adding the biological factor to purely optical-physical considerations and to assess the different solar collectors proposed, in terms specific for the microalgae. The model is tested against production data obtained in different scientific literature. Finally, the exposition concludes with some guidelines for future research.

Silica final lens performance in laser fusion facilities: HiPER and LIFE

Nowadays, the projects LIFE (Laser Inertial Fusion Energy) in USA and HiPER (High Power Laser Energy Research) in Europe are the most advanced ones to demonstrate laser fusion energy viability. One of the main points of concern to properly achieve ignition is the performance of the final optics (lenses) under the severe irradiation conditions that take place in fusion facilities. In this paper, we calculate the radiation fluxes and doses as well as the radiation-induced temperature enhancement and colour centre formation in final lenses assuming realistic geometrical configurations for HiPER and LIFE. On these bases, the mechanical stresses generated by the established temperature gradients are evaluated showing that from a mechanical point of view lenses only fulfil specifications if ions resulting from the imploding target are mitigated. The absorption coefficient of the lenses is calculated during reactor startup and steady-state operation. The obtained results reveal the necessity of new solutions to tackle ignition problems during the startup process for HiPER. Finally, we evaluate the effect of temperature gradients on focal length changes and lens surface deformations. In summary, we discuss the capabilities and weak points of silica lenses and propose alternatives to overcome predictable problems