Influence of molecular composition on the development of microstructure from sheared polyethylene melts: Molecular and lamellar templating

A combination of in situ and ex situ X-ray scattering techniques and transmission electron microscopy has been used to study the crystallization behaviour of polyethylene, following the imposition of melt shear. In the case of a branched material, the imposition of shear flow up to a rate of 30 s(-1) was found to induce no anisotropy. Although shearing the linear material only ever induced a very small degree of anisotropy in the melt, for shear rates > 0.15 s(-1), subsequent crystallization resulted in increasing anisotropy. Blends of the above two polyethylenes were produced, in which the linear material constituted the minority fraction (similar to 10%). Isothermal crystallization at temperatures where extensive crystallization of the branched material does not occur demonstrated that the behaviour of the linear component of the sheared blend mirrored that of the linear polyethylene alone. However, in addition, it was found that when crystallized in the presence of an oriented morphology, the branched polymer also formed anisotropic structures. We have termed the process templating, in which the crystallization behaviour of the bulk of the system (similar to 90% branched material) is completely altered (spherulitic to oriented lamellar) by mapping it onto a pre-existing minority structure (similar to 10% linear polymer). (c) 2006 Elsevier Ltd. All rights reserved.

Seasonality of modern pollen and sediment deposition in an estuarine context: the Severn Estuary Levels, southwest England

Recent sedimentological and palynological research on subfossil Holocene banded sediments from the Severn Estuary Levels suggested seasonality of deposition, registered by variations in mineral grain-size and pollen assemblages between different parts of the bands. Here we provide data that strengthen this interpretation from sampling of modern sediments and pollen deposition on an active mudflat and saltmarsh on the margin of the Severn Estuary, and comparison with a vegetation survey and contemporary records of climate, river and tidal regimes. The results of grain-size analysis indicate deposition of comparatively coarse-grained silts during the relatively cool and windy conditions of winter and comparatively fine-grained sediments during relatively warm and calm summer months. Pollen analysis demonstrates the significance of long-term storage of pollen grains and fern spores in the estuarine waterbody, superimposed on which seasonal variations in pollen inputs from local and regional vegetation remain detectable. Copyright (C) 2007 John Wiley & Sons, Ltd.

Granulometric characterization and evaluation of annually banded mid-Holocene estuarine silts, Welsh Severn Estuary (UK): coastal change, sea level and climate

Holocene silts (salt marshes) and highest intertidal-supratidal peats are superbly exposed on a 15 kin coastal transect which reveals two laterally extensive units of annually banded silts (Beds 3, 7) associated with three transgressive-regressive silt-peat cycles (early sixth-early fourth millennium BC). Bed 3 in places is concordantly and gradationally related to peats above and below, but in others transgresses older strata. Bed 7 also grades up into peat, but everywhere overlies a discordance. The banding in Bed 3 at three main and two minor sites was resolved and characterized texturally at high-resolution (2.5/5 mm contiguous slices) using laser granulometry (LS230 with PIDS) and a comprehensive scheme of data-assessment. Most of Bed 3 formed very rapidly, at peak values of several tens of millimetres annually, in accordance with modelled effects of sea-level fluctuations on mature marshes (bed concordant and gradational) and on marshes growing up after coastal erosion and retreat (bed with discordant base). Using data from the modern Severn Estuary, the textural contrast within bands, and its variation between bands, points to a variable but overall milder mid-Holocene climate than today. The inter-annual variability affected marsh dynamics, as shown by the behaviour of the finely divided plant tissues present. Given local calibration, the methodology is applicable to other tidal systems with banded silts in Britain and mainland northwest Europe. (c) 2006 Elsevier Ltd. All rights reserved.

Soil geochemical analyses as an indication of metal working at the excavation of a house in the Roman City at Silchester (UK)

Silchester is the site of a major late Iron Age and Roman town (Calleva Atrebatum), situated in northern Hampshire (England (UK)) and occupied between the late first century BC and the fifth or sixth century AD. Extensive evidence of the nature of the buildings and the plan of the town was obtained from excavations undertaken between 1890 and 1909. The purpose of this study was to use soil geochemical analyses to reinforce the archaeological evidence particularly with reference to potential metal working at the site. Soil analysis has been used previously to distinguish different functions or land use activity over a site and to aid identification and interpretation of settlement features (Entwistle et al., 2000). Samples were taken from two areas of the excavation on a 1-metre grid. Firstly from an area of some 500 square metres from contexts of late first/early second century AD date throughout the entirety of a large 'town house' (House 1) from which there was prima facie evidence of metalworking.

Comparing the performance of official and unofficial genetically modified cotton in India

Genetically modified (GM) cotton was approved for commercial cultivation in 2002. Hybrids to date have carried the Bt (Bacillus thuringiensis) gene, which confers resistance to Lepidoptera and certain Coleoptera. As well as "official" Bt hybrids (i.e., those that have gone through a formal approval process), there are "unofficial" Bt hybrids produced without such approval. The owners of the official hybrids, Monsanto-Mahyco, claim that the unofficial hybrids are not as good and could even damage the perception of Bt cotton amongst farmers. Anti-GM groups claim that neither type of Bt hybrid provides either yield or economic advantages over non-Bt hybrids. This paper reports the first study of official versus unofficial versus non-Bt hybrids in India (622 farmers in Gujarat State) with the specific aim of comparing one hypothesized ranking in terms of gross margin of (a) official Bt hybrids, (b) unofficial Bt hybrids, and (c) non-Bt hybrids. Results suggest that the official Bt varieties (MECH 12 and MECH 162) significantly outperform the unofficial varieties in terms of gross margin. However, unofficial, locally produced Bt hybrids can also perform significantly better than non-Bt hybrids, although second-generation (F2) Bt seed appears to have no yield advantage compared to non-Bt hybrids but can save on insecticide use. The paper explores some of the implications of this ranking.

Isolating the 'farmer' effect as a component of the advantage of growing genetically modified varieties in developing countries: a Bt cotton case study from Jalgaon, India

The present paper explores the 'farmer' effect in economic advantages often claimed for Bt cotton varieties (those with the endotoxin gene from Bacillus thuringiensis conferring resistance to some insect pests) compared to non-Bt varieties. Critics claim that much of the yield advantage of Bt cotton could be due to the fact that farmers adopting the technology are in a better position to provide inputs and management and so much of any claimed Bt advantage is an artefact rather than reflecting a real advantage of the variety per se. The present paper provides an in-depth analysis of 63 non-adopting and 94 adopting households of Bt cotton in Jalgaon, Maharashtra State, India, spanning the seasons 2002 and 2003. Results suggest that Bt adopters are indeed different from non-adopters in a number of ways. Adopters appear to specialize more on cotton (at least in terms of the land area they devote to the crop), spend more money on irrigation and grow well-performing non-Bt varieties of cotton (Bunny). Taking gross margin as the basis for comparison, Bt plots had 2.5 times the gross margin of non-Bt plots in both seasons. If only adopters are considered then the gross margin advantage of Bt plots reduces to 1.6 times that of non-Bt plots. This is still a significant advantage and could well explain the popularity of Bt in Maharashtra. However, it is clear that great care needs to be taken with such comparative studies.

Making 'dirty' nations look clean? The nation state and the problem of selecting and weighting indices as tools for measuring progress towards sustainability

Pressing global environmental problems highlight the need to develop tools to measure progress towards "sustainability." However, some argue that any such attempt inevitably reflects the views of those creating such tools and only produce highly contested notions of "reality." To explore this tension, we critically assesses the Environmental Sustainability Index (ESI), a well-publicized product of the World Economic Forum that is designed to measure 'sustainability' by ranking nations on league tables based on extensive databases of environmental indicators. By recreating this index, and then using statistical tools (principal components analysis) to test relations between various components of the index, we challenge ways in which countries are ranked in the ESI. Based on this analysis, we suggest (1) that the approach taken to aggregate, interpret and present the ESI creates a misleading impression that Western countries are more sustainable than the developing world; (2) that unaccounted methodological biases allowed the authors of the ESI to over-generalize the relative 'sustainability' of different countries; and, (3) that this has resulted in simplistic conclusions on the relation between economic growth and environmental sustainability. This criticism should not be interpreted as a call for the abandonment of efforts to create standardized comparable data. Instead, this paper proposes that indicator selection and data collection should draw on a range of voices, including local stakeholders as well as international experts. We also propose that aggregating data into final league ranking tables is too prone to error and creates the illusion of absolute and categorical interpretations. (c) 2004 Elsevier Ltd. All rights reserved.

The rejuvenation of tourism in Barbados 1993-2003 - Reflections on the Butler model

This article examines how Barbados as a mature resort destination has set about rejuvenating its tourism product since the early 1990s, when the number of stop-over tourist arrivals showed year-on-year declines. This has been achieved in three principal ways: the extensive upgrading of existing hotel facilities, especially at the luxury end of the market: the increase of overall tourist capacity, and the development of niche markets, especially golf tourism. At both the outset and the conclusion, the rejuvenation of tourism in Barbados between 1993 and 2003 is viewed in light of Butler's (1980) model of resort-cycle development.

Remote sensing of intertidal morphological change in Morecambe Bay, U.K., between 1991 and 2007

Tidal Flats are important examples of extensive areas of natural environment that remain relatively unaffected by man. Monitoring of tidal flats is required for a variety of purposes. Remote sensing has become an established technique for the measurement of topography over tidal flats. A further requirement is to measure topographic changes in order to measure sediment budgets. To date there have been few attempts to make quantitative estimates of morphological change over tidal flat areas. This paper illustrates the use of remote sensing to measure quantitative and qualitative changes in the tidal flats of Morecambe Bay during the relatively long period 1991–2007. An understanding of the patterns of sediment transport within the Bay is of considerable interest for coastal management and defence purposes. Tidal asymmetry is considered to be the dominant cause of morphological change in the Bay, with the higher currents associated with the flood tide being the main agency moulding the channel system. Quantitative changes were measured by comparing a Digital Elevation Model (DEM) of the intertidal zone formed using the waterline technique applied to satellite Synthetic Aperture Radar (SAR) images from 1991–1994, to a second DEM constructed from airborne laser altimetry data acquired in 2005. Qualitative changes were studied using additional SAR images acquired since 2003. A significant movement of sediment from below Mean Sea Level (MSL) to above MSL was detected by comparing the two Digital Elevation Models, though the proportion of this change that could be ascribed to seasonal effects was not clear. Between 1991 and 2004 there was a migration of the Ulverston channel of the river Leven north-east by about 5 km, followed by the development of a straighter channel to the west, leaving the previous channel decoupled from the river. This is thought to be due to independent tidal and fluvial forcing mechanisms acting on the channel. The results demonstrate the effectiveness of remote sensing for measurement of long-term morphological change in tidal flat areas. An alternative use of waterlines as partial bathymetry for assimilation into a morphodynamic model of the coastal zone is also discussed.

LiDAR mapping of tidal marshes for ecogeomorphological modelling in the TIDE project

The European research project TIDE (Tidal Inlets Dynamics and Environment) is developing and validating coupled models describing the morphological, biological and ecological evolution of tidal environments. The interactions between the physical and biological processes occurring in these regions requires that the system be studied as a whole rather than as separate parts. Extensive use of remote sensing including LiDAR is being made to provide validation data for the modelling. This paper describes the different uses of LiDAR within the project and their relevance to the TIDE science objectives. LiDAR data have been acquired from three different environments, the Venice Lagoon in Italy, Morecambe Bay in England, and the Eden estuary in Scotland. LiDAR accuracy at each site has been evaluated using ground reference data acquired with differential GPS. A semi-automatic technique has been developed to extract tidal channel networks from LiDAR data either used alone or fused with aerial photography. While the resulting networks may require some correction, the procedure does allow network extraction over large areas using objective criteria and reduces fieldwork requirements. The networks extracted may subsequently be used in geomorphological analyses, for example to describe the drainage patterns induced by networks and to examine the rate of change of networks. Estimation of the heights of the low and sparse vegetation on marshes is being investigated by analysis of the statistical distribution of the measured LiDAR heights. Species having different mean heights may be separated using the first-order moments of the height distribution.

Uses of airborne scanning laser altimetry for river flood modelling and coastal geomorphology

Two ongoing projects at ESSC that involve the development of new techniques for extracting information from airborne LiDAR data and combining this information with environmental models will be discussed. The first project in conjunction with Bristol University is aiming to improve 2-D river flood flow models by using remote sensing to provide distributed data for model calibration and validation. Airborne LiDAR can provide such models with a dense and accurate floodplain topography together with vegetation heights for parameterisation of model friction. The vegetation height data can be used to specify a friction factor at each node of a model’s finite element mesh. A LiDAR range image segmenter has been developed which converts a LiDAR image into separate raster maps of surface topography and vegetation height for use in the model. Satellite and airborne SAR data have been used to measure flood extent remotely in order to validate the modelled flood extent. Methods have also been developed for improving the models by decomposing the model’s finite element mesh to reflect floodplain features such as hedges and trees having different frictional properties to their surroundings. Originally developed for rural floodplains, the segmenter is currently being extended to provide DEMs and friction parameter maps for urban floods, by fusing the LiDAR data with digital map data. The second project is concerned with the extraction of tidal channel networks from LiDAR. These networks are important features of the inter-tidal zone, and play a key role in tidal propagation and in the evolution of salt-marshes and tidal flats. The study of their morphology is currently an active area of research, and a number of theories related to networks have been developed which require validation using dense and extensive observations of network forms and cross-sections. The conventional method of measuring networks is cumbersome and subjective, involving manual digitisation of aerial photographs in conjunction with field measurement of channel depths and widths for selected parts of the network. A semi-automatic technique has been developed to extract networks from LiDAR data of the inter-tidal zone. A multi-level knowledge-based approach has been implemented, whereby low level algorithms first extract channel fragments based mainly on image properties then a high level processing stage improves the network using domain knowledge. The approach adopted at low level uses multi-scale edge detection to detect channel edges, then associates adjacent anti-parallel edges together to form channels. The higher level processing includes a channel repair mechanism.

Origin and structure of Devensian depressions at Letton, Herefordshire

Groups of circular to oval enclosed depressions in soft sediments of Pleistocene age are relatively common in north-west Europe. These features are normally interpreted as being either glacial or periglacial in origin. Where these features are developed in glacial sediments, a glacial (and specifically ‘kettle hole’) genesis is considered most likely. Some groups of features, however, have been re-interpreted as being periglacial in origin and are thought to be the remains of cryogenic mounds (former pingos or palsas/lithalsas). The problem at many sites, of course, is correct identification and previously this was often resolved through extensive trenching of the sediments. The use of geophysics in the form of electrical resistivity tomography and ground probing radar, however, can aid investigation and interpretation and is less invasive. A group of enclosed depressions in the Letton area of Herefordshire within the Last Glacial Maximum ice limit (Late Devensian) have been investigated in this way. The morphology and internal structure of the features and their existence in glaciolacustrine sediments of Late Devensian age strongly suggests that these depressions are kettle holes resulting from ice block discharge into a shallow lakes or lakes, and hence a glacial origin is supported. The lack of any ramparts surrounding the depressions (at the surface or any evidence of these at depth) and the fact that they do not overlap (‘mutually interfere’) indicates that they are not the remains of cryogenic mounds.

Profitability and technical efficiency of aquaculture systems in Pampanga, Philippines

We evaluate the profitability and technical efficiency of aquaculture in the Philippines. Farm-level data are used to compare two production systems corresponding to the intensive monoculture of tilapia in freshwater ponds and the extensive polyculture of shrimps and fish in brackish water ponds. Both activities are very lucrative, with brackish water aquaculture achieving the higher level of profit per farm. Stochastic frontier production functions reveal that technical efficiency is low in brackish water aquaculture, with a mean of 53%, explained primarily by the operator's experience and by the frequency of his visits to the farm. In freshwater aquaculture, the farms achieve a mean efficiency level of 83%. The results suggest that the provision of extension services to brackish water fish farms might be a cost-effective way of increasing production and productivity in that sector. By contrast, technological change will have to be the driving force of future productivity growth in freshwater aquaculture.

Isolating the 'farmer' effect as a component of the advantage of growing genetically modified varieties in developing countries: a Bt cotton case study from Jalgaon, India

The present paper explores the 'farmer' effect in economic advantages often claimed for Bt cotton varieties (those with the endotoxin gene from Bacillus thuringiensis conferring resistance to some insect pests) compared to non-Bt varieties. Critics claim that much of the yield advantage of Bt cotton could be due to the fact that farmers adopting the technology are in a better position to provide inputs and management and so much of any claimed Bt advantage is an artefact rather than reflecting a real advantage of the variety per se. The present paper provides an in-depth analysis of 63 non-adopting and 94 adopting households of Bt cotton in Jalgaon, Maharashtra State, India, spanning the seasons 2002 and 2003. Results suggest that Bt adopters are indeed different from non-adopters in a number of ways. Adopters appear to specialize more on cotton (at least in terms of the land area they devote to the crop), spend more money on irrigation and grow well-performing non-Bt varieties of cotton (Bunny). Taking gross margin as the basis for comparison, Bt plots had 2.5 times the gross margin of non-Bt plots in both seasons. If only adopters are considered then the gross margin advantage of Bt plots reduces to 1.6 times that of non-Bt plots. This is still a significant advantage and could well explain the popularity of Bt in Maharashtra. However, it is clear that great care needs to be taken with such comparative studies.

Inequality and GM crops: a case study of Bt cotton in India

Critics of genetically modified (GM) crops often contend that their introduction enhances the gap between rich and poor farmers, as the former group are in the best position to afford the expensive seed as well as provide other inputs such as fertilizer and irrigation. The research reported in this paper explores this issue with regard to Bt cotton (cotton with the endotoxtin gene from Bacillus thuringiensis conferring resistance to some insect pests) in Jalgaon, Maharashtra State, India, spanning the 2002 and 2003 seasons. Questionnaire–based survey results from 63 non–adopting and 94 adopting households of Bt cotton were analyzed, spanning 137 Bt cotton plots and 95 non–Bt cotton plots of both Bt adopters and non–adopters. For these households, cotton income accounted for 85 to 88% of total household income, and is thus of vital importance. Results suggest that in 2003 Bt adopting households have significantly more income from cotton than do non–adopting households (Rp 66,872 versus Rp 46,351) but inequality in cotton income, measured with the Gini coefficient (G), was greater amongst non–adopters than adopters. While Bt adopters had greater acreage of cotton in 2003 (9.92 acres versus 7.42 for non–adopters), the respective values of G were comparable. The main reason for the lessening of inequality amongst adopters would appear to be the consistency in the performance of Bt cotton along with the preferred non–Bt cultivar of Bt adopters—Bunny. Taking gross margin as the basis for comparison, Bt plots had 2.5 times the gross margin of non–Bt plots of non–adopters, while the advantage of Bt plots over non–Bt plots of adopters was 1.6 times. Measured in terms of the Gini coefficient of gross margin/acre it was apparent that inequality was lessened with the adoption of Bunny (G = 0.47) and Bt (G = 0.3) relative to all other non–Bt plots (G = 0.63). Hence the issue of equality needs to be seen both in terms of differences between adopters and non–adopters as well as within each of the groups.